Search NASA⌕ Search

SEARCH · Search NASA

Results for “stream operators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Computational Analysis of the Combustion Processes in an Axisymmetric, RBCC Flowpath

Computational fluid dynamic simulations have been used to study the combustion processes within an axisymmetric, RBCC flowpath. Two distinct operating modes have been analyzed to date, including the independent ramjet stream (IRS) cycle and the supersonic combustion ramjet (scramJet) cycle. The IRS cycle investigation examined the influence of fuel-air ratio, fuel distribution, and rocket chamber pressure upon the combustion physics and thermal choke characteristics. Results indicate that adjustment of the amount and radial distribution of fuel can control the thermal choke point. The secondary massflow rate was very sensitive to the fuel-air ratio and the rocket chamber pressure. The scramjet investigation examined the influence of fuel-air ratio and fuel injection schedule upon combustion performance estimates. An analysis of the mesh-dependence of these calculations was presented. Jet penetration data was extracted from the three-dimensional simulations and compared favorably with experimental correlations of similar flows. Results indicate that combustion efficiency was very sensitive to the fuel schedule.

Steffen, Christopher J., Jr.↗

Regenerable Air Purification System for Gas-Phase Contaminant Control

A regenerable air purification system (RAPS) that uses water vapor to displace adsorbed contaminants from an. adsorbent column into a closed oxidation loop is under development through cooperative R&D between Vanderbilt University and NASA Ames Research Center. A unit based on this design can be used for removing trace gas-phase contaminants from spacecraft cabin air or from polluted process streams including incinerator exhaust. Recent work has focused on fabrication and operation of a RAPS breadboard at NASA Ames, and on measurement of adsorption isotherm data for several important organic compounds at Vanderbilt. These activities support the use and validation of RAPS modeling software also under development at Vanderbilt, which will in turn be used to construct a prototype system later in the project.

Constantinescu, Ileana C.↗

GPS-Based Navigation And Orbit Determination for the AMSAT AO-40 Satellite

The AMSAT OSCAR-40 (AO-40) spacecraft occupies a highly elliptical orbit (HEO) to support amateur radio experiments. An interesting aspect of the mission is the attempted use of GPS for navigation and attitude determination in HEO. Previous experiences with GPS tracking in such orbits have demonstrated the ability to acquire GPS signals, but very little data were produced for navigation and orbit determination studies. The AO-40 spacecraft, flying two Trimble Advanced Navigation Sensor (TANS) Vector GPS receivers for signal reception at apogee and at perigee, is the first to demonstrate autonomous tracking of GPS signals from within a HEO with no interaction from ground controllers. Moreover, over 11 weeks of total operations as of June 2002, the receiver has returned a continuous stream of code phase, Doppler, and carrier phase measurements useful for studying GPS signal characteristics and performing post-processed orbit determination studies in HEO. This paper presents the initial efforts to generate AO-40 navigation solutions from pseudorange data reconstructed from the TANS Vector code phase, as well as to generate a precise orbit solution for the AO-40 spacecraft using a batch filter.

Davis, George↗

Systematic Wind-Tunnel Measurements on Missiles

Wind-tunnel measurements on projectiles are discussed. Tests at the Gottingen Tunnel are described. The tunnel operates on the Prandtl principle, that is, a brief stationary air stream produced in an evacuated tank by induction of atmospheric air.

Walchner, O.↗

Noise Source Location and Flow Field Measurements on Supersonic Jets and Implications Regarding Broadband Shock Noise

An experiment was conducted in an effort to obtain data that would provide a better understanding of the origins of broadband shock noise (BBSN). Phased array noise source location and two types of flow field data (background oriented schlieren and particle image velocimetry) were acquired on unheated, single-stream jets. Results are presented for one subsonic and four supersonic operating conditions. These data show that BBSN is created primarily in the downstream portion of the shock train with peak BBSN production occurring near where the average size of the turbulent structures is equal to the shockcell spacing. These data tend to validate theories that BBSN is created by turbulent structures that are as large or larger than the shock spacing.

Podboy, Gary G.↗

Test data analysis of the thermodynamic vent system-augmented top spray injector liquid nitrogen transfer experiments

Traditionally, a cryogenic tank must be pre-chilled to some “target” temperature before the main vent valve can be closed to attempt a non-vented fill (NVF) of cryogenic liquid propellant. This methodology is particularly attractive for performing in-space transfer of cryogens due to the unknown location of the liquid/vapor interface in microgravity and the high likelihood of venting liquid if the vent valve is opened during transfer. This paper presents in-depth test data analysis of a Thermodynamic Vent System (TVS) augmented injector used for cryogenic tank chilldown and fill experiments of a thin-walled Titanium tank. Eight tests were conducted using liquid nitrogen across a range of inlet conditions and boundary conditions, and three different chilldown/fill methods. For four of the tests, the injector sprays liquid into the tank as normal, but also uses a TVS heat exchanger to cool the metallic injector itself as well as the main incoming liquid stream. Results show that using the TVS augmented injector simplifies transfer operation via enhanced condensation at the injector surface at the cost of sacrificing only a small amount of propellant.

No-vent Fill↗

Single-pass parallel prefix scan with dynamic look back

One embodiment of the present invention performs a parallel prefix scan in a single pass that incorporates variable look-back. A parallel processing unit (PPU) subdivides a list of inputs into sequentially-ordered segments and assigns each segment to a streaming multiprocessor (SM) included in the PPU. Notably, the SMs may operate in parallel. Each SM executes write operations on a segment descriptor that includes the status, aggregate, and inclusive-prefix associated with the assigned segment. Further, each SM may execute read operations on segment descriptors associated with other segments. In operation, each SM may perform reduction operations to determine a segment-wide aggregate, may perform look-back operations across multiple preceding segments to determine an exclusive-prefix, and may perform a scan seeded with the exclusive prefix to generate output data. Advantageously, the PPU performs one read operation per input, thereby reducing the time required to execute the prefix scan relative to prior-art parallel implementations.

Merrill, Duane↗

LCA of Carbon Capture Retrofit Using the “Petra Nova Style” Model - LCAXVIII

This work was presented at the American Center for Life Cycle Assessment (ACLCA) LCAXVIII Conference in Fort Collins, CO on September 26, 2018. This analysis compares the life cycle environmental impacts for an amine-based capture retrofit with an external co-gen source providing the utility inputs for capture compared to a more traditional retrofit in which the plant/unit output is de-rated with the utility inputs for operating the capture system coming directly from the plant. One of the major differences between the designs is that in the case of the external co-gen unit, the combustion emissions associated with operating the capture unit are not part of the flue gas stream that is directed to the capture unit. Another unique consideration in this analysis is the inclusion of the upstream natural gas life cycle in the boundaries of the co-gen retrofit.

Krynock, Michelle↗

Learning method and system for separating independent and dependent attacks

Streams of monitoring node signal values over time, representing a current operation of the industrial asset, are used to generate current monitoring node feature vectors. Each feature vector is compared with a corresponding decision boundary separating normal from abnormal states. When a first monitoring node passes a corresponding decision boundary, an attack is detected and classified as an independent attack. When a second monitoring node passes a decision boundary, an attack is detected and a first decision is generated based on a first set of inputs indicating if the attack is independent/dependent. From the beginning of the attack on the second monitoring node until a final time, the first decision is updated as new signal values are received for the second monitoring node. When the final time is reached, a second decision is generated based on a second set of inputs indicating if the attack is independent/dependent.

97 MATHEMATICS AND COMPUTING↗

Hydraulic Properties of Grout Monoliths Containing Organic Ion Exchange Resin - 18369

The Waste Treatment and Immobilization Plant (WTP) at Hanford is being constructed to treat 56 million gallons of radioactive waste currently stored in underground tanks at the Hanford site. Operation of the WTP will generate several solid secondary waste (SSW) streams including spent spherical resorcinol formaldehyde cation exchange resin (IXr). The current plan for safe disposal of IXr is solidification in cementitious material (CM) typically comprised of cement, fly ash and blast furnace slag. Three CM formulations were tested to stabilize IXr for long-term land disposal. Two IXr loading rates, 0.1 and 0.3 v/v IXr:grout were used with the three CM formulations to prepare simulated waste form monoliths for hydraulic property testing. Following curing, the monoliths were removed from molds and tested to determine saturated hydraulic conductivity (K{sub sat}) and water retention properties. K{sub sat} was measured using a standard flexible permeameter method ASTM D-5084-10. A constant vapor pressure (CVP) method was used to determine van Genuchten parameters for desorption moisture retention curves for each of the SSW grout formulations. For the CVP method, vacuum saturated, intact wafers approximately 1.25 cm thick were placed above a saturated salt solution inside a sealed container for equilibration. Each saturated salt solution has an associated vapor pressure related to relative humidity in the container. Visual examination and three-dimensional x-ray micro computed tomography (μCT) indicated that the IXr was uniformly distributed in the cured waste form. Saturated hydraulic conductivity was within the range previously reported by Flach et al. in a study of the hydraulic properties of 98 pastes and grouts. The solidification of IXr in CM resulted in a waste form with water retention properties similar to cementitious pastes. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Panel Session 120: Roundtable: Waste Management - Energy Facilities Contractor Operating Group (EFCOG WM)

This Roundtable focused on the WM EFCOG working group as they met to discuss a variety of issues of importance to US DOE waste management operations. The purpose of the WM EFCOG is to seek out and promote the best management and operating practices, cost effective technologies and disposal options for all waste streams generated at US DOE facilities whether destined for US DOE or commercial facilities. Each site representative provided a radioactive waste management lessons learned briefing. Panelists with presentations: Savannah River Site (SRS) Solid Waste Program Update (Kerri Crawford); Idaho Clean-up Project Status (Frederick Hughes); West Valley Demonstration Project Update - EFCOG Waste Management Working Group (John Rendall); Key Project Challenges and Successes (Kalli Shupe); EFCOG WMWG Challenging Waste Subgroup Update (Tammy Monday); CH TRU Difficult Waste Stream Processing Challenges (Daniel Pancake); Argonne Building 350 Clean-up Success Using Effective Work Control (Daniel Dilday); Problematic Waste Streams on the Oak Ridge Reservation (John Wrapp)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Heat Transfer Experiments of Ribbed, Serpentine Cooling Passages with Supercritical CO2

The results of heat transfer experiments with supercritical CO2 (sCO2) to capture the performance of ribbed, serpentine cooling passages for Reynolds numbers in the range of 100,000 - 400,000 are presented. The oxy-combustion turbine operating in an Allam-Fetvedt cycle has a turbine inlet temperature exceeding 1100°C, necessitating internally cooled turbine blades due to material creep strength limits. Reynolds numbers for sCO2, with its combination of high fluid density and low viscosity, can be up to an order of magnitude higher than comparable internal cooling conditions for an air-breathing engine where the majority of experimental data exists. To improve the prediction of cooling performance through turbulated passages, a test rig was designed and constructed with interchangeable insert capability for operation in sCO2 with heat transfer from a heater outlet flow stream to a lower temperature recuperator outlet flow stream. The inserts included serpentine passage geometry with five passes, one of the inserts including chevron ribs and the other a plain wall. The multi-pass serpentine geometry allowed for the evaluation of the effects 180 deg. tip turns have on the return passage flow characteristics, as they can depart significantly from fully-developed flow characteristics. The test procedure included the use of a modified Wilson plot method, with hot flow stream conditions kept effectively constant so that monitored changes in the overall thermal resistance could be attributed to manipulations in cooling flow stream conditions. Conditions during testing consisted of test section pressures of approximately 180 bar, cooling flow stream temperature of 175°C and hot flow stream temperature of 410°C. Test points at discrete cool flow Reynolds numbers up to 400,000 demonstrated an expected trend of decreased fluid thermal resistance with increasing Reynolds number, while at comparable Reynolds number there was an exhibited lower thermal resistance and higher passage pressure drop for the ribbed insert compared to the plain-walled insert. Processing of test data included establishment of Nusselt number enhancement ratios, so that for different internal cooling passage dimensions in the actual turbine blade at comparable Reynolds number the ratio could be applied to predict cooling performance.

Marshall, Michael↗

Libby Mitigation Program, 2007 Annual Progress Report: Mitigation for the Construction and Operation of Libby Dam.

Libby Reservoir was created under an International Columbia River Treaty between the United States and Canada for cooperative water development of the Columbia River Basin (Columbia River Treaty 1964). Libby Reservoir inundated 109 stream miles of the mainstem Kootenai River in the United States and Canada, and 40 miles of tributary streams in the U.S. that provided habitat for spawning, juvenile rearing, and migratory passage (Figure 1). The authorized purpose of the dam is to provide power (91.5%), flood control (8.3%), and navigation and other benefits (0.2%; Storm et al. 1982). The Pacific Northwest Power Act of 1980 recognized possible conflicts stemming from hydroelectric projects in the northwest and directed Bonneville Power Administration to 'protect, mitigate, and enhance fish and wildlife to the extent affected by the development and operation of any hydroelectric project of the Columbia River and its tributaries' (4(h)(10)(A)). Under the Act, the Northwest Power Planning Council was created and recommendations for a comprehensive fish and wildlife program were solicited from the region's federal, state, and tribal fish and wildlife agencies. Among Montana's recommendations was the proposal that research be initiated to quantify acceptable seasonal minimum pool elevations to maintain or enhance the existing fisheries (Graham et al. 1982). Research to determine how operations of Libby Dam affect the reservoir and river fishery and to suggest ways to lessen these effects began in May 1983. The framework for the Libby Reservoir Model (LRMOD) was completed in 1989. Development of Integrated Rule Curves (IRCs) for Libby Dam operation was completed in 1996 (Marotz et al. 1996). The Libby Reservoir Model and the IRCs continue to be refined (Marotz et al 1999). Initiation of mitigation projects such as lake rehabilitation and stream restoration began in 1996. The primary focus of the Libby Mitigation project now is to restore the fisheries and fish habitat in basin streams and lakes. 'Mitigation for the Construction and Operation of Libby Dam' is part of the Northwest Power and Conservation Council's (NPCC) resident fish and wildlife program. The program was mandated by the Northwest Planning Act of 1980, and is responsible for mitigating damages to fish and wildlife caused by hydroelectric development in the Columbia River Basin. The objective of Phase I of the project (1983 through 1987) was to maintain or enhance the Libby Reservoir fishery by quantifying seasonal water levels and developing ecologically sound operational guidelines. The objective of Phase II of the project (1988 through 1996) was to determine the biological effects of reservoir operations combined with biotic changes associated with an aging reservoir. The objectives of Phase III of the project (1996 through present) are to implement habitat enhancement measures to mitigate for dam effects, to provide data for implementation of operational strategies that benefit resident fish, monitor reservoir and river conditions, and monitor mitigation projects for effectiveness. This project completes urgent and high priority mitigation actions as directed by the Kootenai Subbasin Plan.

13 HYDRO ENERGY↗

Southern Hemisphere meteor stream determinations

Meteor orbits have been deduced from radio observations of meteor trails carried out at Adelaide, Australia, using a combined multistation CW and pulse radar system operating at 27 MHz. The orbits of 1667 meteors have been determined down to a limiting radio magnitude of +8. The data have been systematically searched for stream meteors, and the significance of minor associations has been appraised. Altogether, 40.4% of the orbits were found to be associated with at least one other orbit, and 29.8% with two or more. Numerous minor streams with high inclination and low eccentricity have been found at deep southern declinations from December to March, with little activity in this quarter during June and October. In addition to confirming several previously established cometary associations, a comprehensive search has indicated that 34 of the meteor associations may be related to 17 comets. Associations between several long-period comets and low-eccentricity high-inclination streams appear to be indisputable, and they confirm the origin of at least some of the 'toroidal group' meteors.

Gartrell, G.↗

HC-NIDS: signatures and simulations for detecting cyber-attacks aiming to cause damage against cyber-physical energy systems

Physical device safety is typically implemented locally using embedded controllers, while operations safety is primarily performed in control centers. Safe operations can be enhanced by correct design of device-level control algorithms, and protocols, procedures and operator training at the control-room level, but all can fail. Moreover, these elements exchange data and issue commands via vulnerable communication layers. In order to secure these gaps and enhance operational safety, we believe monitoring of command sequences must be combined with an awareness of physical device limitations and automata models that capture safety mechanisms. One way of doing this is by leveraging specification-based intrusion detection to monitor for physical constraint violations. The method can also verify that physical infrastructure state is consistent with monitoring information and control commands exchanged between field devices and control centers. This additional security layer enhances protection from both outsider attacks and insider mistakes. We implemented specification-based SCADA command analyzers using physical constraint algorithms directly in the Bro framework and Broccoli APIs for three separate scenarios: a water heater, an automated distribution system, and an over-current protection scheme. To accomplish this, we added low-level analyzers capable of examining control system-specific protocol packets for both Modbus TCP and DNP3, and also higher-level analyzers able to interpret device command and data streams within the context of each device's physical capabilities and present operational state. Thus the software that we are making available includes the Bro/Broccoli scripts for these three scenarios, as well as simulators, written in C, of those scenarios that generate sample traffic that is monitored by the Bro/Broccoli scripts. In addition, we have also implemented systems to directly pull cyber-physical information from the OSIsoft PI historian system. We have included the Python scripts used to perform that monitoring.

Source record↗

HC-NIDS: signatures and simulations for detecting cyber-attacks aiming to cause damage against cyber-physical energy systems

Physical device safety is typically implemented locally using embedded controllers, while operations safety is primarily performed in control centers. Safe operations can be enhanced by correct design of device-level control algorithms, and protocols, procedures and operator training at the control-room level, but all can fail. Moreover, these elements exchange data and issue commands via vulnerable communication layers. In order to secure these gaps and enhance operational safety, we believe monitoring of command sequences must be combined with an awareness of physical device limitations and automata models that capture safety mechanisms. One way of doing this is by leveraging specification-based intrusion detection to monitor for physical constraint violations. The method can also verify that physical infrastructure state is consistent with monitoring information and control commands exchanged between field devices and control centers. This additional security layer enhances protection from both outsider attacks and insider mistakes. We implemented specification-based SCADA command analyzers using physical constraint algorithms directly in the Bro framework and Broccoli APIs for three separate scenarios: a water heater, an automated distribution system, and an over-current protection scheme. To accomplish this, we added low-level analyzers capable of examining control system-specific protocol packets for both Modbus TCP and DNP3, and also higher-level analyzers able to interpret device command and data streams within the context of each device's physical capabilities and present operational state. Thus the software that we are making available includes the Bro/Broccoli scripts for these three scenarios, as well as simulators, written in C, of those scenarios that generate sample traffic that is monitored by the Bro/Broccoli scripts. In addition, we have also implemented systems to directly pull cyber-physical information from the OSIsoft PI historian system. We have included the Python scripts used to perform that monitoring.

Source record↗

Copper and bismuth-based sorbent characterization in simulated iodine off-gas streams

The effective capture of volatile radioiodine, a fission product present in used nuclear fuel (UNF), is of paramount importance for development of used fuel reprocessing schemes to prevent release of radioiodine during unit operations and to meet regulatory standards for air emissions. A well-studied method for iodine capture in off-gas streams is the use of silver-functionalized zeolite phases (AgZ), which exploit chemisorption of I to Ag. Advances into other Ag-functionalized materials, including aerogels and metal organic frameworks (MOFs), are underway [1]. Additional metals with the capability to chemisorb iodine, including Cu, Bi, and Sn, [1] are being evaluated as alternatives to Ag for potential applicability to iodine management in off-gas systems. The design of novel functionalized sorbents with Cu and Bi, including composites with metal particles embedded in PAN substrates [2] and composites with metal sulfides embedded in PAN [3], is an ongoing area of study for improved iodine capture. Previously reported work on novel PAN-based metal sorbents has provided the synthesis, characterization, and iodine capture efficiency of this new class of sorbent. Specifically, the metal sulfide PAN composites are found to be easy to produce and reproduce, as well as having a high iodine loading potential under static conditions [3]. Due to the favorable testing previously performed with metal sulfide PAN composites, further testing into the performance of these composites under gas streams containing I2(g) in combination with NO2(g) and H2O(g) is needed. Humid streams of NO2(g) may arise from dissolver off-gas streams, when used fuel is dissolved in HNO3(aq) [4]. NO2(g) has been found to reduce AgZ sorption capacity for I because of oxidation of Ag, the chemisorbing agent, to Ag2O [5]. It follows that performance evaluation of novel sorbents under highly oxidizing conditions such as NO2(g) streams is critical. Therefore, the objective of this study is to determine the effect of flowing NO2(g) and H2O(g) streams on iodine sorption capacity and sorbent performance. This work utilizes custom-built gas handling capabilities for sorbent exposure along with solid-state characterization techniques to assess the physical and chemical properties of sorbents before and after exposure.

copper, bismuth, iodine capture, iodine sorbent, p↗

Testing of an Iodine and Tritium Removal System for Advanced Tritium Pretreatment Off-Gas

The reprocessing of used nuclear fuel would release volatile radionuclides into the off-gas of a processing plant, including 3 H, 14 C, 85 Kr, and 129 I. For a reprocessing plant sited within the United States and governed by US regulations, the abatement of some or all of these radionuclides from the plant off-gas would be required before discharge of that gas to the environment. A potential simplification of the off-gas management system can be achieved through an efficient advanced tritium pretreatment (ATPT) step in which the UO 2 fuel is oxidized by NO 2 prior to dissolution. Oxidation of the UO 2 fuel matrix results in the release of tritium contained within. Up-front removal of tritium from the fuel in a pretreatment step, followed by the abatement of tritium from the advanced tritium pretreatment off-gas (ATPTOG) stream, can minimize or eliminate the distribution of tritium throughout the plant, also decreasing or eliminating the need for tritium capture on multiple off-gas streams. The use of NO 2 as the oxidant allows tritium pretreatment to be performed at lower temperatures and may result in the quantitative release of iodine from the fuel. A total of five tests examined AgA as a potential iodine sorbent at an operating temperature of 150°C and both 3A MS and silica gel as potential tritium sorbents with an operating temperature of 40°C. 3A MS and silica gel are intended for use as regenerative sorbents, in which the adsorbed tritium (as tritiated water or tritiated nitric acid) is loaded onto the sorbent at operating temperature and then subsequently desorbed at high temperature into a small-volume gas stream for recovery and conversion to a waste form. This testing leaves many fundamental questions regarding the ATPTOG iodine and tritium abatement systems unanswered. These include questions regarding sorbent capacity and sorbate desorption. Overall, this testing indicates that tritium and iodine abatement from an ATPTOG stream by solid sorbents is currently at a low stage of technological development and that deployment of such an abatement system would require substantial additional research and development.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗