Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface layering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

Evidence of a reduction reaction of oxidized iron/cobalt by boron atoms diffused toward naturally oxidized surface of CoFeB layer during annealing

We have investigated the redox reaction on the surface of Ta/CoFeB/MgO/CoFeB magnetic tunnel junction stack samples after annealing at 300, 350, and 400 °C for 1 h using angle-resolved X-ray photoelectron spectroscopy for precise analysis of the chemical bonding states. At a capping tantalum layer thickness of 1 nm, both the capping tantalum layer and the surface of the underneath CoFeB layer in the as-deposited stack sample were naturally oxidized. By comparison of the Co 2p and Fe 2p spectra among the as-deposited and annealed samples, reduction of the naturally oxidized cobalt and iron atoms occurred on the surface of the CoFeB layer. The reduction reaction was more significant at higher annealing temperature. Oxidized cobalt and iron were reduced by boron atoms that diffused toward the surface of the top CoFeB layer. A single CoFeB layer was prepared on SiO{sub 2}, and a confirmatory evidence of the redox reaction with boron diffusion was obtained by angle-resolved X-ray photoelectron spectroscopy analysis of the naturally oxidized surface of the CoFeB single layer after annealing. The redox reaction is theoretically reasonable based on the Ellingham diagram.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural-phase states and wear resistance of surface formed on steel by surfacing

Investigations of elementary and phase structure, state of defect structure and tribological characteristics of a surfacing, formed on a low carbon low-alloy steel by a welding method were carried out. It was revealed that a surfacing, formed on a steel surface is accompanied by the multilayer formation, and increases the wear resistance of the layer surfacing as determined.

36 MATERIALS SCIENCE↗

X-ray diffraction study of defects in zinc-diffusion-doped silicon

Samples of CZ n-Si〈Zn〉(111) are prepared by high-temperature zinc-diffusion annealing followed by quenching and are studied by X-ray diffraction. The silicon contains an initial phosphorus impurity and zinc-compensating admixture at concentrations N{sub P} = 1.5 × 10{sup 14} cm{sup −3} and N{sub Zn} = 1 × 10{sup 14} cm{sup −3}; i.e., the relation N{sub P}/2 < N{sub Zn} < N{sub P} is fulfilled. Microdefects are studied by double- and triple-crystal X-ray diffraction in the dispersion free modes (n, −n) and (n, −n, +n). The samples are found to contain microdefects with two characteristic sizes (average sizes of about 1 μm and 70 nm). The interplanar distance in the near-surface layer with a thickness of 0.1 μm is smaller than this parameter in the remaining matrix, the difference being equal to d{sub 0} Δd/d{sub 0} ≈ 2 × 10{sup −5}. This layer contains mainly vacancy-type microdefects. The angle between the reflecting planes and the local surface relief is Δψ = (7 ± 1) arcmin.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Rapid surface hardening and enhanced tribological performance of 4140 steel by friction stir processing

Tribological performance of steel materials can be substantially enhanced by various thermal surface hardening processes. For relatively low-carbon steel alloys, case carburization is often used to improve surface performance and durability. If the carbon content of steel is high enough (>0.4%), thermal treatments such as induction, flame, laser, etc. can produce adequate surface hardening without the need for surface compositional change. This paper presents an experimental study of the use of friction stir processing (FSP) as a means to hardened surface layer in AISI 4140 steel. The impacts of this surface hardening process on the friction and wear performance were evaluated under both dry and lubricated contact conditions in reciprocating sliding. FSP produced the same level of hardening and superior tribological performance when compared to conventional thermal treatment, using only 10% of the energy and without the need for quenching treatments. With FSP surface hardness of about 7.8 GPa (62 Rc) was achieved while water quenching conventional heat treatment produced about 7.5 GPa (61 Rc) hardness. Microstructural analysis showed that both FSP and conventional heat treatment produced martensite. Although the friction behavior for FSP treated surfaces and the conventional heat treatment were about the same, the wear in FSP processed surfaces was reduced by almost 2× that of conventional heat treated surfaces. Furthermore, the superior performance is attributed to the observed grain refinement accompanying the FSP treatment in addition to the formation of martensite. As it relates to tribological performance, this study shows FSP to be an effective, highly energy efficient, and environmental friendly (green) alternative to conventional heat treatment for steel.

36 MATERIALS SCIENCE↗

Oxygen Transport Kinetics in Infiltrated SOFCs Cathode by Electrical Conductivity Relaxation Technique

Infiltration has attracted increasing attention as an effective technique to modify SOFC cathodes to improve cell electrochemical performance while maintaining material compatibility and long-term stability. However, the infiltrated material's effect on oxygen transport is still not clear and detailed knowledge of the oxygen reduction reaction in infiltrated cathodes is lacking. In this work, the technique of electrical conductivity relaxation (ECR) is used to evaluate oxygen exchange in two common infiltrated materials, Ce{sub 0.8}Sm{sub 0.2}O{sub 1.9} and La{sub 0.6}Sr{sub 0.4}CoO{sub 3-δ}. The ECR technique is also used to examine the transport processes in a composite material formed with a backbone of La{sub 0.6}Sr{sub 0.4}Co{sub 0.2}Fe{sub 0.8}O{sub 3-δ} and possessing a thin, dense surface layer composed of the representative infiltrate material. Both the surface oxygen exchange process and the oxygen exchange coefficient at infiltrate/LSCF interface are reported. ECR testing results indicate that the application of infiltrate under certain oxygen partial pressure conditions produces a measureable increase in the fitted oxygen exchange parameter. It is presently only possible to generate hypotheses to explain the observation. However the correlation between improved electrochemical performance and increased oxygen transport measured by ECR is reliably demonstrated. The simple and inexpensive ECR technique is utilized as a direct method to optimize the selection of specific infiltrate/backbone material systems for superior performance.

30 DIRECT ENERGY CONVERSION↗

Remote sensing of soil moisture - Recent advances

Recent advancements in microwave remote sensing of soil moisture include a method for estimating the dependence of the soil dielectric constant on its texture, the use of a percent of field capacity to express soil moisture magnitudes independently of soil texture, methods of estimating soil moisture sampling depth, and models for describing the effect of surface roughness on microwave response in terms of surface height variance and horizontal correlation length, as well as the verification of radiative transfer model predictions of microwave emission from soils and methods for the estimation of vegetation effects on the microwave response to soil moisture. Such researches have demonstrated that it is possible to remotely sense soil moisture in the 0-5 cm soil surface layer, and simulation studies have indicated how remotely sensed surface soil moisture may be used to estimate evapotranspiration rates and root-zone soil moisture.

Schmugge, T. J.↗

Surface Fatigue Resistance with Induction Hardening

Induction hardening has been used for some years to harden the surface and improve the strength and service life of gears and other components. Many applications that employ induction hardening require a relatively long time to finish the hardening process and controlling the hardness of the surface layer and its depth often was a problem. Other surface hardening methods, ie., carbonizing, take a very long time and tend to cause deformations of the toothing, whose elimination requires supplementary finishing work. In double-frequency induction hardening, one uses a low frequency for the preheating of the toothed wheel and a much higher frequency for the purpose of rapidly heating the surface by way of surface hardening.

Townsend, Dennis↗

Rollable Thin-Shell Nanolaminate Mirrors

A class of lightweight, deployable, thin-shell, curved mirrors with built-in precise-shape-control actuators is being developed for high-resolution scientific imaging. This technology incorporates a combination of advanced design concepts in actuation and membrane optics that, heretofore, have been considered as separate innovations. These mirrors are conceived to be stowed compactly in a launch shroud and transported aboard spacecraft, then deployed in outer space to required precise shapes at much larger dimensions (diameters of the order of meters or tens of meters). A typical shell rollable mirror structure would include: (1) a flexible single- or multiple-layer face sheet that would include an integrated reflective surface layer that would constitute the mirror; (2) structural supports in the form of stiffeners made of a shape-memory alloy (SMA); and (3) piezoelectric actuators. The actuators, together with an electronic control subsystem, would implement a concept of hierarchical distributed control, in which (1) the SMA actuators would be used for global shape control and would generate the large deformations needed for the deployment process and (2) the piezoelectric actuators would generate smaller deformations and would be used primarily to effect fine local control of the shape of the mirror.

Hickey, Gregory↗

Structural properties 3,16-bis triisopropylsilylethynyl (pentacene) (TIPS-pentacene) thin films onto organic dielectric layer using slide coating method

3,16-bis triisopropylsilylethynyl (Pentacene) (TIPS-Pentacene) compactable interface property is important in order to have a good arrangement of molecular structure. Comparison for TIPS-Pentacene deposited between two different surface layers conducted. 0.1wt% TIPS-Pentacene diluted in chloroform were deposited onto poly(methylmeaclyrate) (PMMA) layered transparent substrates using slide coating method. X-ray diffraction (XRD) used to determine crystallinity of thin films. Series of (00l) diffraction peaks obtained with sharp first peaks (001) for TIPS-Pentacene deposited onto PMMA layer at 5.35° and separation of 16.3 Å. Morphology and surface roughness were carried out using scanning electron microscope (SEM) and surface profilemeter LS500, respectively.TIPS-Pentacene deposited onto PMMA layer formed needled-like-shape grains with 10.26 nm surface roughness. These properties were related as thin film formed and its surface roughness plays important role towards good mobility devices.

36 MATERIALS SCIENCE↗

The salinity effect in a mixed layer ocean model

A model of the thermally mixed layer in the upper ocean as developed by Kraus and Turner and extended by Denman is further extended to investigate the effects of salinity. In the tropical and subtropical Atlantic Ocean rapid increases in salinity occur at the bottom of a uniformly mixed surface layer. The most significant effects produced by the inclusion of salinity are the reduction of the deepening rate and the corresponding change in the heating characteristics of the mixed layer. If the net surface heating is positive, but small, salinity effects must be included to determine whether the mixed layer temperature will increase or decrease. Precipitation over tropical oceans leads to the development of a shallow stable layer accompanied by a decrease in the temperature and salinity at the sea surface.

Miller, J. R.↗

Change in the electronic properties of an InAs (111)A surface at oxygen and fluorine adsorption

Based on ab initio calculations, the adsorption of oxygen and fluorine on reconstructed (2 Multiplication-Sign 2) and unreconstructed (1 Multiplication-Sign 1) InAs (111)A surfaces is studied. The most stable adsorption positions are determined. It is shown that adsorption of oxygen on both surfaces gives rise to electronic states in the band gap. The preferential positions for oxygen adsorption on an InAs (111)A (2 Multiplication-Sign 2) surface are those where oxygen is bonded both to indium atoms and to arsenic atoms in the surface layer and also the vacant site between three indium atoms (the 'In-hollow position). Adsorption of fluorine brings about a pushing of the surface states out of the band gap; the position above indium atoms (the 'In-top position) is preferential for adsorbed fluorine. Adsorption of fluorine on an InAs (111)A (1 Multiplication-Sign 1) surface leads to the elimination of the surface state formed by indium p orbitals and to an unpinning of the Fermi level.

36 MATERIALS SCIENCE↗

Fluorination‐Enhanced Surface Stability of Disordered Rocksalt Cathodes

Abstract Cation‐disordered rocksalt (DRX) oxides are a promising new class of high‐energy‐density cathode materials for next‐generation Li‐ion batteries. However, their capacity fade presents a major challenge. Partial fluorine (F) substitution into the oxygen (O) lattice appears to be an effective strategy for improving the cycling stability, but the underlying atomistic mechanism remains elusive. Here, using a combination of advanced transmission electron microscopy based imaging and spectroscopy techniques, the structural and chemical evolution upon cycling of Mn‐based DRX cathodes with an increasing F content (Li–Mn–Nb–O–F x , x = 0, 0.05, 0.2) are probed. The atomic origin behind the beneficial effect of high‐level fluorination for enhancing the surface stability of the DRX is revealed. It is discovered that, due to the reduced O redox activity while with increasing F concentration, F in the DRX lattice mitigates the formation of an O‐deficient surface layer upon cycling. For low F‐substituted DRX, the O loss near the surface results in the formation of an amorphous cathode–electrolyte interphase layer and nanoscale voids after extended cycling. Increased F concentration in the DRX lattice minimizes both O loss and the interfacial reactions between DRX and the liquid electrolyte, enhancing the surface stability of DRX. These results provide guidance on the development of next‐generation cathode materials through anion substitution.

Li, Linze↗

Robust A -Type Order and Spin-Flop Transition on the Surface of the Antiferromagnetic Topological Insulator MnBi 2 Te 4

Here, we present microscopic evidence of the persistence of uniaxial A-type antiferromagnetic order to the surface layers of MnBi 2 Te 4 single crystals using magnetic force microscopy. Our results reveal termination-dependent magnetic contrast across both surface step edges and domain walls, which can be screened by thin layers of soft magnetism. The robust surface A-type order is further corroborated by the observation of termination-dependent surface spin-flop transitions, which have been theoretically proposed decades ago. Our results not only provide key ingredients for understanding the electronic properties of the antiferromagnetic topological insulator MnBi 2 Te 4 , but also open a new paradigm for exploring intrinsic surface metamagnetic transitions in natural antiferromagnets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Investigation of surface termination by directional elastic peak electron spectroscopy: Experiment and theory

Experimental and theoretical details concerning the directional elastic peak electron spectroscopy are presented. The application of this experimental method to the identification of a crystalline structure of surface layers is shown for Cu(111) and Ru(0001), which enables the analysis of different surface terminations associated with different sequences of atoms along the surface normal. Theoretical data are obtained by applying the multiple scattering theory and different sources of phase shifts. The quantitative analysis performed by an R-factor reveals almost the same populations of A and B terminated (0001) terraces and proves explicitly the presence of steps of atomic height on the clean Ru(0001) surface. This is not the case for the Cu(111) surface, where the terrace termination does not affect the distribution of atomic directions within the first few atomic layers. The averaging of theoretical data versus scattering volume defined by the sphere radius R{sub max} around the emitter site is discussed in view of the computation time optimization. - Highlights: • We examined the structure and surface termination of fcc and hcp monocrystals. • Crystalline structure within the first few atomic layers was determined by DEPES. • Multiple scattering formalism was used to obtain theoretical results. • Populations of terraces with different terminations were determined. • Scattering parameters are discussed in the context of computation time optimization.

36 MATERIALS SCIENCE↗

Texture Analysis of Inconel 718 with Different Modes During Single-Track Laser Surface Re-Melting

An in-depth understanding of the texture formation in melt pools allows for the modification of the surface layer microstructure and corresponding material properties, providing an opportunity to integrate laser surface re-melting into metal additive manufacturing. This study investigates crystallographic texture formation at different cooling rates in single melting tracks on the Inconel 718 (IN718) plate produced by laser surface re-melting. The cooling rate varies from 2.31 × 10 5 °C/s to 9.56 × 10 5 °C/s with the increase in scanning rates from 400 mm/s to 1200 mm/s, measured by recently developed real-time temperature monitoring of melt pools. Columnar grains are dominant, with distinct crystallographic textures forming in the melt pools. At a slower scanning speed, the keyhole mode shows three different textures forming at different depths (crystallographically layered structure), while, at a faster scanning speed, the conduction mode shows only random grain orientation. There are no pores/voids detected, and the columnar grain morphology and columnar grain width (8.6 μm to 12.4 μm) follow the analysis framework in terms of thermal gradient and solidification rate analysis. This implies that laser surface re-melting provides the potential to modify the surface structure from a random grain orientation to a crystallographically layered structure.

36 MATERIALS SCIENCE↗

An Operational Overview of the EXport Processes in the Ocean from RemoTe Sensing (EXPORTS) Northeast Pacific Field Deployment

The goal of the EXport Processes in the Ocean from RemoTe Sensing (EXPORTS) field campaign is to develop a predictive understanding of the export, fate, and carbon cycle impacts of global ocean net primary production. To accomplish this goal, observations of export flux pathways, plankton community composition, food web processes, and optical, physical, and biogeochemical (BGC) properties are needed over a range of ecosystem states. Here we introduce the first EXPORTS field deployment to Ocean Station Papa in the Northeast Pacific Ocean during summer of 2018, providing context for other papers in this special collection. The experiment was conducted with two ships: a Process Ship, focused on ecological rates, BGC fluxes, temporal changes in food web, and BGC and optical properties, that followed an instrumented Lagrangian float; and a Survey Ship that sampled BGC and optical properties in spatial patterns around the Process Ship. An array of autonomous underwater assets provided measurements over a range of spatial and temporal scales, and partnering programs and remote sensing observations provided additional observational context. The oceanographic setting was typical of late-summer conditions at Ocean Station Papa: a shallow mixed layer, strong vertical and weak horizontal gradients in hydrographic properties, sluggish sub-inertial currents, elevated macronutrient concentrations and low phytoplankton abundances. Although nutrient concentrations were consistent with previous observations, mixed layer chlorophyll was lower than typically observed, resulting in a deeper euphotic zone. Analyses of surface layer temperature and salinity found three distinct surface water types, allowing for diagnosis of whether observed changes were spatial or temporal.The 2018 EXPORTS field deployment is among the most comprehensive biological pump studies ever conducted. A second deployment to the North Atlantic Ocean occurred in spring 2021, which will be followed by focused work on data synthesis and modeling using the entire EXPORTS data set.

Biological pump↗

The Oceanic Barrier Layer in the Eastern Indian Ocean as a Predictor for Rainfall Over Indonesia and Australia

Barrier layers in the tropics trap heat in a shallow and stable near-surface layer and limit entrainment of cooler water from below. Both processes act to increase sea surface temperature and enhance atmospheric convection. The high resolution fully coupled pre-industrial Energy Exascale Earth System Model version 0 (E3SMv0) is used to investigate the relationship between barrier layers in the eastern Indian Ocean during the wet season with local atmospheric convection and remote rainfall. A partial least squares regression reveals a significant relationship between Australasian rainfall and the barrier layer thickness (BLT) west of Sumatra, occurring one month earlier. Furthermore, the largest positive regression coefficients are over northern Australia. The region west of Sumatra is strategically located where the East-Asian monsoon moisture flows toward northern Australia. Thickening of the west Sumatra BLT intensifies evaporation and local convection and amplifies the moisture transported to Australia acting to increase the terrestrial rainfall.

58 GEOSCIENCES↗

Formation and breakdown of a protective layer of chromium sesquioxide on L-605 alloy at 1100 C

The formation and breakdown of a protective layer of Cr2O3 on the cobalt-base alloy L-605 during oxidation at 1100 C was evaluated. Deformed surface layers, pressure, and moisture were variables. Increasing surface deformation, decreasing pressure, and decreasing moisture increased time to breakdown. A model was deduced. The breakdown of the Cr2O3 layer was caused by a combination of growth stresses and volatilization. Breakdown exposed a chromium-depleted alloy to air, resulting in very rapid oxidation, which continued until consumption of the depletion zone was complete.

Lowell, C. E.↗