Search NASA⌕ Search

SEARCH · Search NASA

Results for “BioMass”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Pretreatment of Biomass by Selected Type-III Deep Eutectic Solvents and Evaluation of the Pretreatment Effects on Hydrothermal Carbonization

Hydrothermal carbonization (HTC) is a novel thermochemical conversion that converts wet biomass into energy dense solid fuel. Residual moisture under subcritical conditions reacts with a lignin-cellulose-hemicellulose matrix with the major reactions being identified as dehydration and decarboxylation. Among other reaction parameters (e.g., temperature, time, pressure), biomass morphology often plays a key role in HTC. The hypothesis of this study was enhancing the porous structure of biomass without significantly affecting biopolymer composition would augment hydrothermal carbonization (HTC). To prove the hypothesis, two type-III deep eutectic solvents (DESs), namely choline chloride:urea (ChCl:Urea, 1:2 mol/mol) and methyltriphenylphosphonium bromide:ethylene glycol (MTPB:EG, 1:4 mol/mol), were studied to pretreat loblolly pine at room temperature and ambient pressure for 1 h. DES pretreatment shows swelling of the biomass, increasing the surface fiber-to-fiber gap length by 52% and 185% for ChCl:Urea and MPTB:EG pretreatments, respectively. The total pore volume remained intact (2.6 × 10 –3 cm 3 /g), although new small pores evolved, and existing pores were abated with DES pretreatment. Hydrochars prepared from DES pretreated loblolly pine showed a high O/C and H/C ratio resulting in a significant increase of energy content (up to 42%) and a decrease of mass yield (up to 50 wt %), indicating an enhancement of HTC severity due to the alteration of surface morphology by DES. Finally, a preliminary process economics revealed that integrated DES pretreatment-HTC would increase fixed capital investment but decrease the cost of operation and manufacturing than the standalone HTC process.

09 BIOMASS FUELS↗

Wear Mechanism Analysis of a New Rotary Shear Biomass Comminution System

A new biomass comminution system, Crumbler rotary shear, was developed to process fuel-grade biomass. The rotary shear is more efficient than the traditional hammer mill in comminuting high-moisture biomass and producing more uniform particles with minimal fines. However, the milling unit experiences significant wear in processing dirty woodchips. This study investigated the wear mechanisms of the rotary shear system based on analysis of the minerals carried by woodchips and characterization of actual worn components. Abrasive wear was found to be the dominant effect, and localized adhesive wear (material transfer), microfracture (chipping), and plastic deformation were additional effects. Connections have been made between the wear progression of key cutting components and the particle size change of biomass extrinsic minerals. On the basis of the wear mechanism understanding, mitigations based on advanced tool materials and optimized tool geometric designs are being developed for improving the tool life and cutting efficiency.

09 BIOMASS FUELS↗

Process Model-Based Validation of the Intensification of Biomass Fast Pyrolysis in a Fluidized Bed via Autothermal Operation

A model for the fluidized-bed pyrolysis of biomass is extended to enable the simulation of intensified autothermal operation. In this system, partial oxidation of char and pyrolysate species replaces an external heat source to supply the enthalpy of pyrolysis, greatly increasing the throughput of a given fast pyrolysis reactor. Oxidation reactions are compiled from CRECK and other literature sources and extended to cover the species found in pyrolysis products, including a derivation of the catalytic effect of ash on char combustion from experimental studies at Iowa State University (ISU). Results indicate a roughly 3-fold increase in biomass throughput for a given reactor volume at the pilot scale with minimal loss of valuable products, in agreement with published data from the 3 × 10 -2 m 3 reactor operated by ISU. Additionally, a proposal for a 250 ton/day commercial-scale biomass pyrolysis reactor is analyzed, showing that the same size reactor operated by heating the fluidizing gas externally would have only one-tenth the capacity; if operated by heating the sand externally, the sand would need to circulate at an impractical 0.7 bed volume per minute rate to maintain a 250 ton/day biomass throughput.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Wedge-Shaped Hopper Design for Milled Woody Biomass Flow

The bioenergy industry has been challenged by unstable flow and transport of milled biomass in material handling operations. Handling issues such as hopper clogging and auger jamming are attributed to knowledge gaps between existing handling units designed for bulk solids and their suitability for milled biomass with high compressibility. This work investigates various flow behaviors of granular woody biomass in wedge-shaped hoppers. Herein, hopper flow physical experiments and numerical simulations are conducted to study the influence of the critical material attributes and critical processing parameters on the flow pattern, arching, and throughput. The results show that (1) the preferred flow pattern, mass flow, can be achieved by controlling the material’s internal friction angle, hopper inclination, and hopper wall friction; (2) hopper arching, governed by the competing gravity-driven force against flow resistance from material internal friction and material–wall friction, can be controlled by the hopper wall friction angle and the inclination angle; and (3) flow throughput can be accurately estimated from our empirical equation with inputs of hopper outlet geometry and particle-scale to bulk-scale material attributes. This study elucidates woody biomass flow physics and provides guidance for industrial equipment design.

09 BIOMASS FUELS↗

Real-Time and Post-Reaction Microscopic Structural Analysis of Biomass Undergoing Pyrolysis

The structural complexity of unprocessed plant tissues used for thermochemical conversion of biomass to fuels and energy impedes heat and mass transfer and may increase the occurrence of tar-forming secondary chemical reactions. At industrial scales, gas and liquid products trapped within large biomass particles may reduce net fuel yields and increase tars, impacting industrial operations and increasing overall costs. Real-time microscopic analysis of poplar (Populus sp.) wood samples undergoing anoxic, pyrolytic heat treatment has revealed a pattern of tissue and macropore expansion and collapse. Post-reaction structural analyses of biomass char (biochar) by light and transmission electron microscopy have provided direct structural evidence of pyrolysis product mass-transfer issues, including trapped pyrolysis products and cell wall compression, and have demonstrated the impact of heat-transfer problems on biomass particles. Finally, microscopic imaging has revealed that pyrolyzed/gasified biochars recovered from a fluidized bed reactor retain a similar pre-reaction basic plant tissue structure as the samples used in this study, suggesting that the phenomena observed here are representative of those that occur in larger scale reactors.

BASIC BIOLOGICAL SCIENCES,BIOMASS FUELS↗

Case Study of Water-Soluble Metal Containing Organic Constituents of Biomass Burning Aerosol

Natural and prescribed biomass fires are a major source of aerosols that may persist in the atmosphere for several weeks. Biomass burning aerosols (BBA) can be associated with long-range transport of water-soluble N-, S-, P-, and metal-containing species. In this study, BBA samples were collected using a particle-into-liquid sampler (PILS) from laboratory burns of vegetation collected on military bases in the southeastern and southwestern United States. The samples were then analyzed using high resolution electrospray ionization mass spectrometry (ESI/HR-MS) that enabled accurate mass measurements for hundreds of species with m/z values between 70 and 1000 and assignment of elemental formulas. Mg, Al, Ca, Cr, Mn, Fe, Ni, Cu, Zn, and Ba-containing organometallic species were identified. The results suggest that the biomass may have accumulated metal-containing species that were re-emitted during biomass burning. Finally, further research into the sources, dispersion, and persistence of metal-containing aerosols, as well as their environmental effects, is needed.

09 BIOMASS FUELS↗

A Random Walk Model for Biomass Particle Mixing in Bubbling Fluidized Beds

We propose a physically motivated random walk model to describe the spatial and temporal mixing of a single biomass particle in a bubbling fluidized bed. The model parameters are estimated from measurements of a magnetically tagged simulated biomass particle in a laboratory fluidized bed. We demonstrate that Monte Carlo simulations using the model match key statistical features of the observed behavior reasonably well. These results suggest that a model of this type can simulate the effects of biomass particle mixing in biomass conversion reactors. We suggest possible improvements to the random walk model and propose how it might be used in conjunction with computational fluid dynamics simulations.

09 BIOMASS FUELS↗

Vertical distribution and radiative effects of mineral dust and biomass burning aerosol over West Africa during DABEX

This paper presents measurements of the vertical distribution of aerosol extinction coefficient over West Africa, during the Dust and Biomass burning aerosol Experiment (DABEX) / African Monsoon Multidisciplinary Analysis dry season Special Observing period zero (AMMA-SOP0). In situ aircraft measurements from the UK FAAM aircraft are compared with two ground based lidars (POLIS and ARM MPL) and an airborne lidar on an ultra-light aircraft. In general mineral dust was observed at low altitudes (up to 2km) and a mixture of biomass burning aerosol and dust was observed at altitudes of 2-5km. The study exposes difficulties associated with spatial and temporal variability when inter-comparing aircraft and ground measurements. Averaging over many profiles provided a better means of assessing consistent errors and biases associated with in situ sampling instruments and retrievals of lidar ratios. Shortwave radiative transfer calculations and a 3-year simulation with the HadGEM2-A climate model show that the radiative effect of biomass burning aerosol is somewhat sensitive to the vertical distribution of aerosol. Results show a 15% increase in absorption of solar radiation by elevated biomass burning aerosol when the observed low-level dust layer is included as part of the background atmospheric state in the model. This illustrates that the radiative forcing of anthropogenic absorbing aerosol is sensitive to the treatment of other aerosol species and that care is needed in simulating natural aerosols assumed to exist in the pre-industrial, or natural state of the atmosphere.

09 BIOMASS FUELS↗

A functional metagenomic approach for expanding the synthetic biology toolbox for biomass conversion

Sustainable biofuel alternatives to fossil fuel energy are hampered by recalcitrance and toxicity of biomass substrates to microbial biocatalysts. To address this issue, we present a cultureindependent functional metagenomic platform for mining Nature’s vast enzymatic reservoir and show its relevance to biomass conversion. We performed functional selections on 4.7 Gb of metagenomic fosmid libraries and show that genetic elements conferring tolerance toward seven important biomass inhibitors can be identified. We select two metagenomic fosmids that improve the growth of Escherichia coli by 5.7- and 6.9-fold in the presence of inhibitory concentrations of syringaldehyde and 2-furoic acid, respectively, and identify the individual genes responsible for these tolerance phenotypes. Finally, we combine the individual genes to create a three-gene construct that confers tolerance to mixtures of these important biomass inhibitors. This platform presents a route for expanding the repertoire of genetic elements available to synthetic biology and provides a starting point for efforts to engineer robust strains for biofuel generation.

09 BIOMASS FUELS↗

Heterogeneous Diels–Alder catalysis for biomass-derived aromatic compounds

In this tutorial review, we provide an overview of heterogeneous Diels–Alder catalysis for the production of lignocellulosic biomass-derived aromatic compounds. Diels–Alder reactions afford an extremely selective and efficient route for carbon–carbon cycloadditions to produce intermediates that can readily undergo subsequent dehydration or dehydrogenation reactions for aromatization. As a result, catalysis of Diels–Alder reactions with biomass-derived dienes and dienophiles has seen a growth of interest in recent years; however, significant opportunities remain to (i) tailor heterogeneous catalyst materials for tandem Diels–Alder and aromatization reactions, and (ii) utilize biomass-derived dienes and dienophiles to access both conventional and novel aromatic monomers. As such, this review discusses the mechanistic aspects of Diels–Alder reactions from both an experimental and computational perspective, as well as the synergy of Brønsted–Lewis acid catalysts to facilitate tandem Diels–Alder and aromatization reactions. Heterogeneous catalyst design strategies for Diels–Alder reactions are reviewed for two exemplary solid acid catalysts, zeolites and polyoxometalates, and recent efforts for targeting direct replacement aromatic monomers from biomass are summarized. In conclusion, we point out important research directions for progressing Diels–Alder catalysis to target novel, aromatic monomers with chemical functionality that enables new properties compared to monomers that are readily accessible from petroleum.

09 BIOMASS FUELS↗

Effect of small-scale biomass gasification at the state of refractory lining the fixed bed reactor

The article deals with the influence of biomass gasification on the condition of the refractory lining of a fixed bed reactor. The refractory lining of the gasifier is one part of the device, which significantly affects the operational reliability and durability. After removing the refractory lining of the gasifier from the experimental reactor, there was done an assessment how gasification of different kinds of biomass reflected on its condition in terms of the main factors affecting its life. Gasification of biomass is reflected on the lining, especially through sticking at the bottom of the reactor. Measures for prolonging the life of lining consist in the reduction of temperature in the reactor, in this case, in order to avoid ash fusion biomass which it is difficult for this type of gasifier.

09 BIOMASS FUELS↗

Biomass market dynamics supporting the large‐scale deployment of high‐octane fuel production in the United States

Abstract US Department of Energy research aimed at co‐optimizing fuels and engine performance identified several bioblendstocks that can improve fuel economy including an aromatic‐rich hydrocarbon derived from woody biomass. This work supports an analysis of its large‐scale deployment implying a production target of approximately 15 billion liters of bioblendstock for the supply of 57 billion liters of high‐octane fuel by 2050. It simulates potential transition pathways to lignocellulosic feedstock market structures capable of supplying a mature biorefining industry at this scale. In the present absence of biorefineries, transitions are modeled via nonbiofuel feedstock markets, so‐called companion markets. The resource distribution across several demand industries is simulated to determine biomass availability and price dynamics over time. Results indicate that the wood supply base is mainly influenced by traditional markets including housing and pulp and paper. The selected companion market of wood pellet combustion for heat and electricity generation is found to positively stimulate biomass mobilization, especially in the initial absence of biorefineries. Eventually, biorefineries are found to be able to out‐compete the companion market. As such, they directly benefit from the processing (i.e., pelleting) capacity established to produce commodity‐type intermediates for the companion market. We conclude that the amount of bioblendstock produced is directly related to the size of the companion market (and its pelleting capacity). An initially larger companion market generates up to 20 million dry tonnes of additional feedstock, equivalent to 27 commercial‐scale biorefineries, or an additional production of 5 billion liters by 2050. Distinguishing between industry‐specific feedstock preferences based on average biomass quality characteristics, this analysis goes beyond past research efforts that assume automatic fungibility across different feedstocks. Improving engine performance is a key driver for the promotion of low‐carbon fuels derived from bioblendstocks. This analysis portrays feedstock market transition pathways for their large‐scale deployment.

09 BIOMASS FUELS↗

Miscanthus biomass productivity within US croplands and its potential impact on soil organic carbon

Interest in bioenergy crops is increasing due to their potential to reduce greenhouse gas emissions and dependence on fossil fuels. Here, we combined process-based and geospatial models to estimate the potential biomass productivity of miscanthus and its potential impact on soil carbon stocks in the croplands of the continental United States. The optimum (climatic potential) rainfed productivity for field-dried miscanthus biomass ranged from 1 to 23 Mg biomass ha -1 yr -1 , with a spatial average of 13 Mg ha -1 yr -1 and a coefficient of variation of 30%. This variation resulted primarily from the spatial heterogeneity of effective rainfall, growing degree days, temperature, and solar radiation interception. Cultivating miscanthus would result in a soil organic carbon (SOC) sequestration at the rate of 0.16–0.82 Mg C ha -1 yr -1 across the croplands due to cessation of tillage and increased biomass carbon input into the soil system. We identified about 81 million ha of cropland, primarily in the eastern United States, that could sustain economically viable (>10 Mg ha -1 yr -1 ) production without supplemental irrigation, of which about 14 million ha would reach optimal miscanthus growth. To meet targets of the US Energy Independence and Security Act of 2007 using miscanthus as feedstock, 19 million ha of cropland would be needed (spatial average 13 Mg ha -1 yr -1 ) or about 16% less than is currently dedicated to US corn-based ethanol production.

09 BIOMASS FUELS↗

OsCESA9 conserved-site mutation leads to largely enhanced plant lodging resistance and biomass enzymatic saccharification by reducing cellulose DP and crystallinity in rice

Genetic modification of plant cell walls has been posed to reduce lignocellulose recalcitrance for enhancing biomass saccharification. Several dozen CESA mutants have been reported since cellulose synthase (CESA) gene was first identified, but almost all mutants exhibit the defective phenotypes in plant growth and development. Here, the rice (Oryza sativa) Osfc16 mutant with substitutions (W481C, P482S) at P-CR conserved site in CESA9 shows a slightly affected plant growth and higher biomass yield by 25%–41% compared with wild type (Nipponbare, a japonica variety). Chemical and ultrastructural analyses indicate that Osfc16 has a significantly reduced cellulose crystallinity (CrI) and thinner secondary cell walls compared with wild type. CESA co-IP detection, together with implementations of a proteasome inhibitor (MG132) and two distinct cellulose inhibitors (Calcofluor, CGA), shows that CESA9 mutation could affect integrity of CESA4/7/9 complexes, which may lead to rapid CESA proteasome degradation for low-DP cellulose biosynthesis. These may reduce cellulose CrI, which improves plant lodging resistance, a major and integrated agronomic trait on plant growth and grain production, and enhances biomass enzymatic saccharification by up to 2.3-fold and ethanol productivity by 34%–42%. Our study has for the first time reported a direct modification for the low-DP cellulose production that has broad applications in biomass industries.

09 BIOMASS FUELS↗

Leveling Intermittent Renewable Energy Production Through Biomass Gasification-Based Hybrid Systems

The increased use of intermittent renewable power in the United States is forcing utilities to manage increasingly complex supply and demand interactions. This paper evaluates biomass pathways for hydrogen production and how they can be integrated with renewable resources to improve the efficiency, reliability, dispatchability, and cost of other renewable technologies. Two hybrid concepts were analyzed that involve co-production of gaseous hydrogen and electric power from thermochemical biorefineries. Both of the concepts analyzed share the basic idea of combining intermittent wind-generated electricity with a biomass gasification plant. The systems were studied in detail for process feasibility and economic performance. The best performing system was estimated to produce hydrogen at a cost of $1.67/kg. The proposed hybrid systems seek to either fill energy shortfalls by supplying hydrogen to a peaking natural gas turbine or to absorb excess renewable power during low-demand hours. Direct leveling of intermittent renewable electricity production is accomplished with either an indirectly heated biomass gasifier, or a directly heated biomass gasifier. The indirect gasification concepts studied were found to be cost competitive in cases where value is placed on controlling carbon emissions. A carbon tax in the range of $26-40 per metric ton of CO{sub 2} equivalent (CO{sub 2}e) emission makes the systems studied cost competitive with steam methane reforming (SMR) to produce hydrogen. However, some additional value must be placed on energy peaking or sinking for these plants to be economically viable. The direct gasification concept studied replaces the air separation unit (ASU) with an electrolyzer bank and is unlikely to be cost competitive in the near future. High electrolyzer costs and wind power requirements make the hybridization difficult to justify economically without downsizing the system. Based on a direct replacement of the ASU with electrolyzers, hydrogen can be produced for $0.27 premium per kilogram. Additionally, if a non-renewable, grid-mix electricity is used, the hybrid system is found to be a net CO{sub 2}e emitter.

08 HYDROGEN↗

High temperature pre-digestion of corn stover biomass for improved product yields

Introduction: The efficient conversion of lignocellulosic feedstocks remains a key step in the commercialization of biofuels. One of the barriers to cost-effective conversion of lignocellulosic biomass to sugars remains the enzymatic saccharification process step. Here, we describe a novel hybrid processing approach comprising enzymatic pre-digestion with newly characterized hyperthermophilic enzyme cocktails followed by conventional saccharification with commercial enzyme preparations. Dilute acid pretreated corn stover was subjected to this new procedure to test its efficacy. Thermal tolerant enzymes from Acidothermus cellulolyticus and Caldicellulosiruptor bescii were used to pre-digest pretreated biomass at elevated temperatures prior to saccharification by the commercial cellulase formulation. Results: We report that pre-digestion of biomass with these enzymes at elevated temperatures prior to addition of the commercial cellulase formulation increased conversion rates and yields when compared to commercial cellulase formulation alone under low solids conditions. In conclusion, Our results demonstrating improvements in rates and yields of conversion point the way forward for hybrid biomass conversion schemes utilizing catalytic amounts of hyperthermophilic enzymes.

09 BIOMASS FUELS↗

Ethanol and High-Value Terpene Co-Production from Lignocellulosic Biomass of Cymbopogon flexuosus and Cymbopogon martinii

Cymbopogon flexuosus, lemongrass, and C. martinii, palmarosa, are perennial grasses grown to produce essential oils for the fragrance industry. The objectives of this study were (1) to evaluate biomass and oil yields as a function of nitrogen and sulfur fertilization, and (2) to characterize their utility for lignocellulosic ethanol compared to Panicum virgatum (switchgrass). Mean biomass yields were 12.83 Mg lemongrass ha -1 and 15.11 Mg palmarosa ha -1 during the second harvest year resulting in theoretical biofuel yields of 2541 and 2569 L ethanol ha -1 respectively compared to reported 1749–3691 L ethanol ha -1 for switchgrass. Pretreated lemongrass yielded 198 mL ethanol (g biomass) -1 and pretreated palmarosa yielded 170 mL ethanol (g biomass) -1 . Additionally, lemongrass yielded 85.7 kg essential oil ha-1 and palmarosa yielded 67.0 kg ha -1 with an estimated value of USD $857 and $1005 ha -1 . These data suggest that dual-use crops such as lemongrass and palmarosa may increase the economic viability of lignocellulosic biofuels.

09 BIOMASS FUELS↗

Macroalgae as a Biomass Feedstock: A Preliminary Analysis

A thorough of macroalgae analysis as a biofuels feedstock is warranted due to the size of this biomass resource and the need to consider all potential sources of feedstock to meet current biomass production goals. Understanding how to harness this untapped biomass resource will require additional research and development. A detailed assessment of environmental resources, cultivation and harvesting technology, conversion to fuels, connectivity with existing energy supply chains, and the associated economic and life cycle analyses will facilitate evaluation of this potentially important biomass resource.

09 BIOMASS FUELS↗