Search NASA⌕ Search

SEARCH · Search NASA

Results for “Data Reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

MicroED data collection and processing

The collection and processing of MicroED data are presented. MicroED, a method at the intersection of X-ray crystallography and electron cryo-microscopy, has rapidly progressed by exploiting advances in both fields and has already been successfully employed to determine the atomic structures of several proteins from sub-micron-sized, three-dimensional crystals. A major limiting factor in X-ray crystallography is the requirement for large and well ordered crystals. By permitting electron diffraction patterns to be collected from much smaller crystals, or even single well ordered domains of large crystals composed of several small mosaic blocks, MicroED has the potential to overcome the limiting size requirement and enable structural studies on difficult-to-crystallize samples. This communication details the steps for sample preparation, data collection and reduction necessary to obtain refined, high-resolution, three-dimensional models by MicroED, and presents some of its unique challenges.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The Influence of Pressure on Flame-Flow Characteristics of a Reacting Jet in Crossflow

This work experimentally investigates the effects of elevated combustor pressures on the characteristics of a lean premixed reacting methane/air jet injected into a lean vitiated crossflow using a 12.7 mm axial jet. Experiments were conducted in an axially staged combustor, which implements a reacting jet in crossflow (RJIC) configuration and operates over a pressure range of 1–5 atmospheres. Simultaneous CH* chemiluminescence and particle image velocimetry (PIV) are used to study the flow field and flame behavior. The results show that the reacting jet trajectory exhibits greater penetration with elevated pressure, which is a novel finding compared to available data in the literature. However, the flame liftoff point and ignition delay time both decreased with elevated pressure, which was attributed to decreased vorticity along the flame boundary which corresponds to increased Damköhler numbers (Da). Emissions measurements confirm the NOx increase with pressure as reported in the literature for single-stage gas turbine combustors. Concurrently, emission measurements for the staged configuration show the strong NOx benefit of the RJIC system: the data prove a reduction of global outlet emission levels at elevated pressure with the axially staged configuration. Here, the axial emission reduction was attributed to the decreasing liftoff at elevated pressure levels. Hence, the research emphasizes that the flame and emission characteristics are coupled; they are not only dependent on the geometric parameters and momentum flux ratios but are also a function of pressure.

03 NATURAL GAS↗

Strong suppression of heat conduction in a laboratory replica of galaxy-cluster turbulent plasmas

In conventional gases and plasmas, it is known that heat fluxes are proportional to temperature gradients, with collisions between particles mediating energy flow from hotter to colder regions and the coefficient of thermal conduction given by Spitzer’s theory. However, this theory breaks down in magnetized, turbulent, weakly collisional plasmas, although modifications are difficult to predict from first principles due to the complex, multiscale nature of the problem. Understanding heat transport is important in astrophysical plasmas such as those in galaxy clusters, where observed temperature profiles are explicable only in the presence of a strong suppression of heat conduction compared to Spitzer’s theory. To address this problem, we have created a replica of such a system in a laser laboratory experiment. Our data show a reduction of heat transport by two orders of magnitude or more, leading to large temperature variations on small spatial scales (as is seen in cluster plasmas).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Scalable Tensor Methods for Nonuniform Hypergraphs

While multilinear algebra appears natural for studying the multiway interactions modeled by hypergraphs, tensor methods for general hypergraphs have been stymied by theoretical and practical barriers. A recently proposed adjacency tensor is applicable to nonuniform hypergraphs, but is prohibitively costly to form and analyze in practice. We develop tensor times same vector (TTSV) algorithms for this tensor which improve complexity from $O(n^r)$ to a low-degree polynomial in $r$, where $n$ is the number of vertices and $r$ is the maximum hyperedge size. Our algorithms are implicit, avoiding formation of the order $r$ adjacency tensor. Here, we demonstrate the flexibility and utility of our approach in practice by developing tensor-based hypergraph centrality and clustering algorithms. We also show these tensor measures offer complementary information to analogous graph-reduction approaches on data, and are also able to detect higher-order structure that many existing matrix-based approaches provably cannot.

97 MATHEMATICS AND COMPUTING↗

Algorithms for Efficient Reproducible Floating Point Summation

We define “reproducibility” as getting bitwise identical results from multiple runs of the same program, perhaps with different hardware resources or other changes that should not affect the answer. Many users depend on reproducibility for debugging or correctness. However, dynamic scheduling of parallel computing resources, combined with nonassociative floating point addition, makes reproducibility challenging even for summation, or operations like the BLAS. We describe a “reproducible accumulator” data structure (the “binned number”) and associated algorithms to reproducibly sum binary floating point numbers, independent of summation order. We use a subset of the IEEE Floating Point Standard 754-2008 and bitwise operations on the standard representations in memory. Our approach requires only one read-only pass over the data, and one reduction in parallel, using a 6-word reproducible accumulator (more words can be used for higher accuracy), enabling standard tiling optimization techniques. Summing n words with a 6-word reproducible accumulator requires approximately 9 n floating point operations (arithmetic, comparison, and absolute value) and approximately 3 n bitwise operations. The final error bound with a 6-word reproducible accumulator and our default settings can be up to 2 29 times smaller than the error bound for conventional (recursive) summation on ill-conditioned double-precision inputs.

Computer Science↗

Band Excitation in Scanning Probe Microscopy: Recognition and Functional Imaging

Field confinement at the junction between a biased scanning probe microscope s (SPM) tip and solid surface enables local probing of various bias-induced transformations such as polarization switching, ionic motion, or electrochemical reactions to name a few. The nanoscale size of the biased region is smaller or comparable to features like grain boundaries and dislocations, potentially allows for the study of kinetics and thermodynamics at the level of a single defect. In contrast to classical statistically averaged approaches, this allows one to link structure to functionality and deterministically decipher associated mesoscopic and atomistic mechanisms. Furthermore, this type of information can serve as a fingerprint of local material functionality, allowing for local recognition imaging. Here, current progress in multidimensional SPM techniques based on band-excitation time and voltage spectroscopies is illustrated, including discussions on data acquisition, dimensionality reduction, and visualization along with future challenges and opportunities for the field.

Jesse, Stephen↗

Electrochemistry-Induced Restructuring of Tin-Doped Indium Oxide Nanocrystal Films of Relevance to CO 2 Reduction

The electrochemical reduction of CO 2 into fuels using renewable electricity presents an opportunity to utilize captured CO 2 . Electrocatalyst development has been a primary focus of research in this area. This is especially true at the nanoscale, where researchers have focused on understanding nanostructure-property relationships. However, electrocatalyst structure may evolve during operation. Indium- and tin-based oxides have been widely studied as electrocatalysts for CO 2 reduction to formate, but evolution of these catalysts during operation is not well-characterized. Here, we report the evolution of nanoscale structure of precise tin-doped indium oxide nanocrystals under CO 2 reduction conditions. We show that sparse monolayer nanocrystal films desorb from the electrode upon charging, but thicker nanocrystal films remain, likely due to an increased number of physical contacts. Upon applying a cathodic voltage of –1.0 V vs RHE or greater, the original 10-nm diameter nanocrystals are no longer visible, and instead form a larger microstructural network. Elemental analysis suggests the network is an oxygen-deficient indium-tin metal alloy. We hypothesize that this morphological evolution is the result of nanocrystal sintering due to oxide reduction. Furthermore, these data provide insights into the morphological evolution of tin-doped indium oxide nanocrystal electrocatalysts under reducing conditions and highlight the importance of post-electrochemical structural characterization of electrocatalysts.

25 ENERGY STORAGE↗

Performance improvements of the windowed multipole formalism using a rational fraction approximation of the Faddeeva function

The windowed multipole (WMP) formalism was introduced as a way to calculate Doppler broadened cross sections on the fly during Monte Carlo simulations. While more arithmetic is needed compared to point-wise cross section look-ups, performance remained competitive from the large memory reductions and sequential data access. The single most expensive function call in a depleted fuel assembly problem using WMP comes from the evaluation of the Faddeeva function, which previously relied on a highly accurate, highly-branching algorithm. This paper explores the use of rational fraction approximations tailored to the domain interest of reactor physics applications and the development of lower accuracy approximations sufficient for our application. The rational approximations were implemented and tested in OpenMC on an infinite medium problem to stress the cross section calculation routine and a PWR assembly problem. In both cases, the rational approximation nearly eliminated the ∼ 20% penalty previously observed when comparing to point-wise libraries. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

INVESTIGATION OF HELIUM FLOW LAMINARIZATION AT HIGH TEMPERATURES AND HIGH PRESSURES IN A GRAPHITE FLOW CHANNEL

Abstract: Forced convection experiments were performed with helium to investigate thermal hydraulic phenomena in a heated graphite test section. Flow regimes include turbulent, transition and laminar flows with Reynolds numbers between 500 and 5,000. Experiments were performed with upward flow at different helium temperatures and pressures up to 550 oC and 61 bar, respectively, various flow rates (50-500 SLPM), and heater power up to 6.5 kW. The analyses of the experimental data showed significant reductions in the Reynolds number of up to 50% over the 2.7 m test section between the gas inlet and outlet. Flow laminarization caused by intense heating was defined to occur when the local Nusselt number decreased below 20% of the Nusselt number based on the Gnielinski correlation. In this study, a flow laminarization criterion was considered based on a dimensionless acceleration parameter (Kv) and buoyancy parameter (Bo). Experiments involved high heating rates leading to the wall-to-bulk temperature ratios ranging from 1.8 to 3.4, dimensionless heat flux (q+) from 1x10^-4 to 7x10^-3 and buoyancy parameter (Bo) from 0.001 to 0.5. The latter range covers a value of Bo˜0.1 that has previously been suggested to correspond to the onset of the influence of the buoyancy force.

99 GENERAL AND MISCELLANEOUS↗

Extreme-Scale Algorithms & Software Resilience (EASIR) Architecture-Aware Algorithms for Scalable Performance and Resilience on Heterogeneous Architectures

This project addresses both communication-avoiding algorithms, and reproducible floating-point computation. Communication, i.e. moving data, either between levels of memory or processors over a network, is much more expensive per operation than arithmetic (measured in time or energy), so we seek algorithms that greatly reduce communication. We developed many new algorithms for both dense and sparse, and both direct and iterative linear algebra, attaining new communication lower bounds, and getting large speedups in many cases. We also extended this work in several ways: (1) We minimize writes separately from reads, since writes may be much more expensive than reads on emerging memory technologies, like Flash, sometimes doing asymptotically fewer writes than reads. (2) We extend the lower bounds and optimal algorithms to arbitrary algorithms that may be expressed as perfectly nested loops accessing arrays, where the array subscripts may be arbitrary affine functions of the loop indices (eg A(i), B(i,j+k, k+3*m-7, …) etc.). (3) We extend our communication-avoiding approach to some machine learning algorithms, such as support vector machines. This work has won a number of awards. We also address reproducible floating-point computation. We define reproducibility to mean getting bitwise identical results from multiple runs of the same program, perhaps with different hardware resources or other changes that should ideally not change the answer. Many users depend on reproducibility for debugging or correctness. However, dynamic scheduling of parallel computing resources, combined with nonassociativity of floating point addition, makes attaining reproducibility a challenge even for simple operations like summing a vector of numbers, or more complicated operations like the Basic Linear Algebra Subprograms (BLAS). We describe an algorithm that computes a reproducible sum of floating point numbers, independent of the order of summation. The algorithm depends only on a subset of the IEEE Floating Point Standard 754-2008, uses just 6 words to represent a “reproducible accumulator,” and requires just one read-only pass over the data, or one reduction in parallel. New instructions based on this work are being considered for inclusion in the future IEEE 754-2018 floating-point standard, and new reproducible BLAS are being considered for the next version of the BLAS standard.

97 MATHEMATICS AND COMPUTING↗

ParameterizationBR2

In the following we detail the ramp parameterization procedure. The purpose of this procedure is in reduction of the data volume loaded into PSC. The same approach will be implemented in HLA “Booster Ramp Generator”.

42 ENGINEERING↗

Probabilistic modeling approach for tracking each collision and breakup of computational parcels

A modeling approach for binary collision and particle breakup is presented for a stochastic particle model in which a computational parcel represents a number of similar physical particles. Presented in this report includes sampling from a distribution of discrete data, parcel number reduction, probabilistic calculation of collision rates, and various particle-particle interactions. Modeling of elastic scattering, coalescence and agglomeration, and breakup are discussed for solid-solid, solid-liquid, and liquid-liquid particle collisions. Numerical procedures are also summarized.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

FAIR data infrastructure and tools for AI-assisted streamflow prediction

Focal Area(s) Areas: We discuss how the integration of AI into Earth Science models can impact streamflow predictions at both the science and data levels. Doing so, we address cross-cutting needs related to the goal of making data FAIR (Findable, Accessible, Interoperable, and Re-usable [1]) for seamless use with Artificial Intelligence/Machine Learning (AI/ML) in Earth System Science at DOE. A novel idea is that AI/ML itself can help with the FAIR data goal and address issues in targeted areas e.g. missing data, data quality and reduction. In addition, the interpretability of results obtained with new AI methods is poised to impact broader scientific challenges in hydrology..

54 ENVIRONMENTAL SCIENCES↗

Impact of Color Space and Color Resolution on Vehicle Recognition Models

In this study, we analyze both linear and nonlinear color mappings by training on versions of a curated dataset collected in a controlled campus environment. We experiment with color space and color resolution to assess model performance in vehicle recognition tasks. Color encodings can be designed in principle to highlight certain vehicle characteristics or compensate for lighting differences when assessing potential matches to previously encountered objects. The dataset used in this work includes imagery gathered under diverse environmental conditions, including daytime and nighttime lighting. Experimental results inform expectations for possible improvements with automatic color space selection through feature learning. Moreover, we find there is only a gradual decrease in model performance with degraded color resolution, which suggests the need for simplified data collection and processing. By focusing on the most critical features, we could see improved model generalization and robustness, as the model becomes less prone to overfitting to noise or irrelevant details in the data. Such a reduction in resolution will lower computational complexity, leading to quicker training and inference times.

47 OTHER INSTRUMENTATION↗

HST HOT-JUPITER TRANSMISSION SPECTRAL SURVEY: CLEAR SKIES FOR COOL SATURN WASP-39b

We present the Hubble Space Telescope (HST) Space Telescope Imaging Spectrograph (STIS) optical transmission spectroscopy of the cool Saturn-mass exoplanet WASP-39b from 0.29-1.025 μ m, along with complementary transit observations from Spitzer IRAC at 3.6 and 4.5 μ m. The low density and large atmospheric pressure scale height of WASP-39b make it particularly amenable to atmospheric characterization using this technique. We detect a Rayleigh scattering slope as well as sodium and potassium absorption features; this is the first exoplanet in which both alkali features are clearly detected with the extended wings predicted by cloud-free atmosphere models. The full transmission spectrum is well matched by a clear H{sub 2}-dominated atmosphere, or one containing a weak contribution from haze, in good agreement with the preliminary reduction of these data presented in Sing et al. WASP-39b is predicted to have a pressure-temperature profile comparable to that of HD 189733b and WASP-6b, making it one of the coolest transiting gas giants observed in our HST STIS survey. Despite this similarity, WASP-39b appears to be largely cloud-free, while the transmission spectra of HD 189733b and WASP-6b both indicate the presence of high altitude clouds or hazes. These observations further emphasize the surprising diversity of cloudy and cloud-free gas giant planets in short-period orbits and the corresponding challenges associated with developing predictive cloud models for these atmospheres.

79 ASTRONOMY AND ASTROPHYSICS↗

High-speed Boulders and the Debris Field in DART Ejecta

On 2022 September 26 the Double Asteroid Redirection Test (DART) spacecraft collided with Dimorphos, the moon of the near-Earth asteroid 65803 Didymos, in a full-scale demonstration of a kinetic impactor concept. The companion Light Italian Cubesat for Imaging of Asteroids (LICIACube) spacecraft documented the aftermath, capturing images of the expansion and evolution of the ejecta from 29 to 243 s after the impact. We present results from our analyses of these observations, including an improved reduction of the data and new absolute calibration, an updated LICIACube trajectory, and a detailed description of the events and phenomena that were recorded throughout the flyby. One notable aspect of the ejecta was the existence of clusters of boulders, up to 3.6 m in radius, that were ejected at speeds of up to 52 m s −1 . Our analysis of the spatial distribution of 104 of these boulders suggests that they are likely the remnants of larger boulders shattered by the DART spacecraft in the first stages of the impact. The amount of momentum contained in these boulders is more than 3 times that of the DART spacecraft, and it is directed primarily to the south, almost perpendicular to the DART trajectory. Recoil of Dimorphos from the ejection of these boulders has the potential to change its orbital plane by up to a degree and to impart a non-principal-axis component to its rotation state. Damping timescales for these phenomena are such that the Hera spacecraft, arriving at the system in 2026, should be able to measure these effects.

asteroid dynamics↗

Red Sky with Red Mesa

The Red Sky/Red Mesa supercomputing platform dramatically reduces the time required to simulate complex fuel models, from 4-6 months to just 4 weeks, allowing researchers to accelerate the pace at which they can address these complex problems. Its speed also reduces the need for laboratory and field testing, allowing for energy reduction far beyond data center walls.

180-TERAFLOP↗

Diverse Power Iteration Embeddings and Its Applications

Abstract—Spectral Embedding is one of the most effective dimension reduction algorithms in data mining. However, its computation complexity has to be mitigated in order to apply it for real-world large scale data analysis. Many researches have been focusing on developing approximate spectral embeddings which are more efficient, but meanwhile far less effective. This paper proposes Diverse Power Iteration Embeddings (DPIE), which not only retains the similar efficiency of power iteration methods but also produces a series of diverse and more effective embedding vectors. We test this novel method by applying it to various data mining applications (e.g. clustering, anomaly detection and feature selection) and evaluating their performance improvements. The experimental results show our proposed DPIE is more effective than popular spectral approximation methods, and obtains the similar quality of classic spectral embedding derived from eigen-decompositions. Moreover it is extremely fast on big data applications. For example in terms of clustering result, DPIE achieves as good as 95% of classic spectral clustering on the complex datasets but 4000+ times faster in limited memory environment.

97 MATHEMATICS AND COMPUTING↗