Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffraction pattern”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Microstructure Evolution and Failure Analysis of an Aluminum–Copper Cathode Conductive Head Produced by Explosive Welding

In this paper, microstructure evolution and failure analysis of the aluminum-copper interface of cathode conductive heads during their use were studied. The interface morphologies, compositions, conductivity and mechanical properties were investigated and analyzed. Obvious corrosion was found on the surface of the contact interface, which was more prevalent on an Al matrix. The crack increased sharply in the local metallurgical bonding areas on the interface, with the compound volume having no significant change. The phase transformation occurred on the interface during use, which was investigated using the elemental composition and x-ray diffraction pattern. The microhardness near the interface increased accordingly. An obvious electrical conductivity decrease appeared on the Al/Cu interface of the cathode conductive head after use over a specific time interval. Therefore, the deterioration of the microstructures and corrosion are the primary factors that affect the electrical conductivity and effective bonding, which will lead to eventual failure.

36 MATERIALS SCIENCE↗

Structure-Optical Property Correlations of Arsenic Sulfide Glasses in Visible, Infrared, and Sub-millimeter Regions

Optical properties and structural aspects of AsxS100-x glasses from visible to terahertz wavelengths were explored. A series of annealed, bulk AsxS100-x glasses (x = 30 to 42) were made and their refractive indices determined at terahertz, infrared, and visible frequencies using a combination of a quasi-optical backwards wave oscillator spectrometer for terahertz measurements and a prism coupler for visible and infrared measurements. It was found that refractive index at all frequencies increases with arsenic composition up to 40 atomic % arsenic then decreases with additional arsenic. Structure in x-ray diffraction patterns support the notion of a minimum volume at 40 atomic %, while the average covalent coordination number indicates the rigidity percolation threshold is reached there. At As concentrations > 40 atomic %, the network becomes over-constrained, the molar volume increases.

36 MATERIALS SCIENCE↗

Sol-gel synthesis of Mn1.5Co1.5O4 spinel nano powders for coating applications

Highlights: • Nano powder of Mn/Co spinel, applicable to solid oxide fuel cell, is synthesized. • The sol-gel synthesis of nanocrystalline Mn{sub 1.5}Co{sub 1.5}O{sub 4} spinel is investigated. • Sol-gel annealing temperature, time, and metal-to-citrate ratio are evaluated. • The optimum conditions for producing dual phase of Mn{sub 1.5}Co{sub 1.5}O{sub 4} are achieved. - Abstract: Mn{sub 1.5}Co{sub 1.5}O{sub 4} oxide spinels are widely used as protective coatings for stainless steel interconnects within planar solid oxide fuel cell stacks. Containing both cubic and tetragonal crystalline phases, these Mn/Co oxide spinels exhibit favorable thermal stability and electronic conductivity for the SOFC interconnect application. Slurry-based coating applications of Mn/Co oxides require precursor powders, which can benefit from being nano-structured. In this study, the sol-gel synthesis of nanocrystalline Mn{sub 1.5}Co{sub 1.5}O{sub 4} spinel is investigated. The decomposition of sol-gel precursors, as well as the crystalline phase structures and microstructures of the product Mn{sub 1.5}Co{sub 1.5}O{sub 4} are characterized by differential thermal and thermogravimetric (DTA/TG) analysis, X-ray diffraction (XRD), and transmission electron microscopy (TEM). The effects of various sol-gel annealing temperatures (T), treatment times (t), and citrate-to-metal ratios (Rc) are evaluated. Results suggest that nanocrystalline Mn{sub 1.5}Co{sub 1.5}O{sub 4} spinel can be synthesized around 1050 °C, and that T = 1050 °C, t = 6 h and Rc = 2 are optimum conditions for producing the smallest grain size. Image analysis of TEM results shows that the size of Mn{sub 1.5}Co{sub 1.5}O{sub 4} crystallites increases with increasing temperature, with average particle sizes ranging from ∼70 nm to ∼1 μm. Selected area diffraction pattern (SADP) of Mn{sub 1.5}Co{sub 1.5}O{sub 4} spinel synthesized at 800 °C confirms the dual (cubic/tetragonal) structure of Mn{sub 1.5}Co{sub 1.5}O{sub 4}.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Novel data analysis method for obtaining better performance from a complex 3D-printed collimator

Additively manufactured scattered beam collimators are increasingly being employed to boost the sample to cell peak signal ratio in high pressure neutron diffraction studies because of manufacturing versatility and performance improvements. We study how the measured diffraction pattern is affected by the presence of a collimator downstream of the sample, and develop a novel protocol that provides more effective background rejection. This protocol takes into account critical performance-determinants that were identified in this study, namely: (i) effectively identifying the collimator pattern on the detector; (ii) understanding the dependence of this pattern on sample and cell composition; and (iii) accurately identifying and differentiating the different regions of the pattern on the detector based on the dependency of the cell or sample and finally (iv) resolving the intensities at regions of the detector where neutrons scattered from the sample are preferentially represented, in order to boost the sample to cell peak signal ratio. Application of this novel analysis protocol is shown to increase the collimator performance over the traditional method.

3D printing↗

Signatures of the unique microstructure of additively manufactured steel observed via diffraction

A series of measurements were designed to gain confidence in the interpretation of the peak breadth in diffraction patterns collected from additively manufactured material, which has a novel microstructure in comparison to the well understood microstructure of wrought materials. Stainless steels made with two additive manufacturing techniques were compared to wrought material. Similar patterns observed in the scattering vector dependence for additively manufactured and deformed wrought materials suggested that the broadening in both materials was related to dislocations. Finally, this was confirmed by heat-treatment, during which both materials exhibited recovery due to the annealing of dislocations at the same temperature.

304L stainless-steel↗

Single crystal structure analysis of a single Sm{sub 2}Fe{sub 17}N{sub 3} particle

We performed single crystal structure analysis of Sm{sub 2}Fe{sub 17}N{sub 3} using X-ray diffraction. A pick-up system combined with a micromanipulation tool driven by piezoelectric actuators and a microgripper was used. A single Sm{sub 2}Fe{sub 17}N{sub x} particle with the diameter of about 20 μm was picked up, and X-ray diffraction was measured using an X-ray diffractometer at the synchrotron radiation beamline at the Photon Factory, KEK. Single crystal structure analysis of a Sm{sub 2}Fe{sub 17}N{sub 3} particle was performed and the structure was successfully determined from X-ray diffraction patterns. The space group and the lattice constants were determined to be R-3m (number sign166) a = b = 8.7206 Å and c = 12.6345 Å, respectively. Atomic positions of Sm and Fe atoms were accurately determined by single crystal structure analysis of only one particle.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Magnetic properties of in-plane oriented barium hexaferrite thin films prepared by direct current magnetron sputtering

In-plane c-axis oriented Ba-hexaferrite (BaM) thin films were prepared on a-plane (112{sup ¯}0) sapphire (Al{sub 2}O{sub 3}) substrates by DC magnetron sputtering followed by ex-situ annealing. The DC magnetron sputtering was demonstrated to have obvious advantages over the traditionally used RF magnetron sputtering in sputtering rate and operation simplicity. The sputtering power had a remarkable influence on the Ba/Fe ratio, the hematite secondary phase, and the grain morphology of the as-prepared BaM films. Under 80 W of sputtering power, in-plane c-axis highly oriented BaM films were obtained. These films had strong magnetic anisotropy with high hysteresis loop squareness (M{sub r}/M{sub s} of 0.96) along the in-plane easy axis and low M{sub r}/M{sub s} of 0.03 along the in-plane hard axis. X-ray diffraction patterns and pole figures revealed that the oriented BaM films grew via an epitaxy-like growth process with the crystallographic relationship BaM (101{sup ¯}0)//α-Fe{sub 2}O{sub 3}(112{sup ¯}0)//Al{sub 2}O{sub 3}(112{sup ¯}0)

36 MATERIALS SCIENCE↗

Laser beam scattering on an inhomogeneous ensemble of elliptical discs modelling red blood cells in an ectacytometer

We have theoretically studied the effect of difference in particle shapes on the appearance of the diffraction pattern, which arises in the scattering of a laser beam on a dilute suspension of erythrocytes in an ectacytometer. We have proposed data processing algorithms allowing one to estimate the red blood cell shape parameter variance under conditions of laser ectacytometry. The conclusions of the theoretical analysis are verified experimentally. (laser methods in biology)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Prediction and Measurement of the Kinetics of Isothermal Crystallization and Devitrification of Mold Powder Slags

The rate and extent of formation of crystalline phases in the slag film that develops between the mold and the strand in steel continuous casting determine heat transfer and lubrication between them and therefore play crucial roles in shell integrity. In this work, a commercial mold powder for casting medium carbon (MC) thin steel slabs is selected for carrying out detailed comparisons between predicted and experimental results of the rates of isothermal crystallization and devitrification of liquid and glassy slag, respectively. Predictions are obtained with a kinetic model that combines the induction period (of Šimon and Kolman) and the Kissinger methods to evaluate time–temperature–transformation (TTT) diagrams for the devitrification and crystallization reactions associated with the peaks appearing in non-isothermal thermo-analysis traces. To obtain experimental validation of the diagram, a high-temperature confocal laser scanning microscope (HT-CLSM) is used to rapidly heat or cool a sample, ~ 140 mg, of glassy powder or liquid slag, respectively, to selected isothermal conditions, where it is held for a prescribed length of time before quenching. Identification and quantification of the phases present in the quenched samples are done by a quantitative X-ray powder diffraction analysis (QXRPDA) method that uses a PONKCS (partial or not known crystal structure) procedure based on Le Bail and Rietveld strategies for refinement of diffraction patterns. The many experimental results indicate that the predicted TTT diagrams for devitrification and crystallization of the mold slag give a good estimation of the rate of the transformations that take place at different temperatures and reveal the differences in the reactions that occur along both paths.

36 MATERIALS SCIENCE↗

Creep-induced microstructural evolution in a nickel-based superalloy designed for advanced ultra-supercritical boilers

Highlights: • Microstructural evolution of a nickel-based superalloy during long-term creep was investigated. • Precipitate-free zones (PFZs) widely arose near the grain boundary under stress. • The coarsened and elongated particles in the PFZs were identified as γ′ precipitates. • The boundary movement plays a role in evolution of grain boundary precipitates. - Abstract: Long-term microstructural stability is a major concern for candidate materials used in advanced ultra-supercritical (A-USC) power plants. In the present work, precipitation behavior of a nickel based superalloy designed for A-USC boilers, with a base composition of Ni-25Cr-20Co, was investigated during long-term thermal exposure under different stresses at 1043 K. The results showed that the coarsening of γ′ precipitates in the grain interior had occurred during thermal exposure in the presence and absence of stress. The microstructure around grain boundary was altered remarkably under stress. The precipitate-free zones (PFZs) commonly existed near the grain boundary in the gauge sections of specimens after long-term creep. Coarsened and elongated particles in the PFZs were identified as γ′-Ni{sub 3} (Ti, Al) precipitates by chemical composition analysis and diffraction pattern. Furthermore, the morphology and distribution of MC-type carbides have no significant changes observed due to their good stability, but discontinuous M{sub 23}C{sub 6} appeared under stress, due to formation of PFZs resulting in dissolution of the adjacent M{sub 23}C{sub 6}. Besides, the creep-rupture mechanism was discussed to explore a potential approach for improving creep properties.

36 MATERIALS SCIENCE↗

Synthesis and optical properties of hierarchical pure ZnO nanostructures

We report the catalyst-free synthesis of hierarchical pure ZnO nanostructures with 6-fold structural symmetry by two-step thermal evaporation process. At the first step, the hexagonal-shaped nanowires consisting of a great deal of Zn and little oxide were prepared via the layer-by-layer growth mechanism; and at the second step, hierarchical pure ZnO nanostructures were synthesized by evaporating the Zn source on the basis of the step-one made substrate. Scanning electron microscopy, transmission electron microscope images, and the corresponding selected area electron diffraction pattern have been utilized to reveal the screw dislocation growth mechanism, through which the single crystal ZnO nanorods are epitaxially grown from the side-wall of central axial nanowires. Raman and photoluminescence spectra further indicate that, for the hierarchical ZnO nanostructures, the ultraviolet peak is related to the free exciton recombination, while the oxygen vacancies and high surface-to-volume ratio are responsible for the strong green peak emission.

36 MATERIALS SCIENCE↗

Magnetic field dependent neutron powder diffraction studies of Ru{sub 0.9}Sr{sub 2}YCu{sub 2.1}O{sub 7.9}

Temperature and magnetic field dependent neutron diffraction has been used to study the magnetic order in Ru{sub 0.9}Sr{sub 2}YCu{sub 2.1}O{sub 7.9}. The appearance of (1/2, 1/2, 1/2), (1/2, 1/2, 3/2), and (1/2, 1/2, 5/2) peaks below T{sub M}=140 K manifests the antiferromagnetic order. Neutron diffraction patterns measured in applied magnetic fields from 0 to 6 T show the destruction of the antiferromagnetic order with increasing field. There is no evidence of spontaneous or field-induced long range ferromagnetic order. This latter result contradicts the vast majority of other experimental observations for this system.

36 MATERIALS SCIENCE↗

Long-term stable water vapor permeation barrier properties of SiN/SiCN/SiN nanolaminated multilayers grown by plasma-enhanced chemical vapor deposition at extremely low pressures

We investigated the water vapor permeation barrier properties of 30-nm-thick SiN/SiCN/SiN nanolaminated multilayer structures grown by plasma enhanced chemical vapor deposition at 7 mTorr. The derived water vapor transmission rate was 1.12 × 10{sup −6} g/(m{sup 2} day) at 85 °C and 85% relative humidity, and this value was maintained up to 15 000 h of aging time. The X-ray diffraction patterns revealed that the nanolaminated film was composed of an amorphous phase. A mixed phase was observed upon performing high resolution transmission electron microscope analysis, which indicated that a thermodynamically stable structure was formed. It was revealed amorphous SiN/SiCN/SiN multilayer structures that are free from intermixed interface defects effectively block water vapor permeation into active layer.

36 MATERIALS SCIENCE↗

A simplified algorithm for measuring erythrocyte deformability dispersion by laser ektacytometry

The possibility of measuring the dispersion of red blood cell deformability by laser diffractometry in shear flow (ektacytometry) is analysed theoretically. A diffraction pattern parameter is found, which is sensitive to the dispersion of erythrocyte deformability and to a lesser extent – to such parameters as the level of the scattered light intensity, the shape of red blood cells, the concentration of red blood cells in the suspension, the geometric dimensions of the experimental setup, etc. A new algorithm is proposed for measuring erythrocyte deformability dispersion by using data of laser ektacytometry. (laser applications in medicine)

60 APPLIED LIFE SCIENCES↗

Studying Near-Surface Layers of Germanium Implanted with Cobalt Ions

Results of an investigation of the surface of germanium nanostructured by means of ion implantation are presented. Single-crystalline germanium (c-Ge) plates were irradiated by 40-keV cobalt Co{sup +} ions in a dose range of (2–8) × 10{sup 16} ion/cm{sup 2}. Evolution of the germanium surface morphology with increasing ion dose was studied by method of scanning electron microscopy. It is established that an increase in the ion implantation dose is accompanied by gradual formation of a surface layer consisting of spherical particles with diameters of ~150 nm. Analysis of the X-ray diffraction patterns of samples was indicative of the appearance of nanosized cobalt germanide (CoGe) particles in the ion-implanted surface layer.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural, microstructural and vibrational analyses of the monoclinic tungstate BiLuWO{sub 6}

The bismuth lutetium tungstate phase BiLuWO{sub 6} has been prepared using a solid state route with stoichiometric mixtures of oxide precursors. The obtained polycrystalline phase has been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Raman spectroscopy. In the first step, the crystal structure has been refined using Rietveld method: the crystal cell was resolved using monoclinic system (parameters a, b, c, β) with space group A2/m. SEM images showed the presence of large crystallites with a constant local nominal composition (BiLuW). TEM analyses showed that the actual local structure could be better represented by a superlattice (a, 2b, c, β) associated with space groups P2 or P2/m. The Raman spectroscopy showed the presence of vibrational bands similar to those observed in the compounds BiREWO{sub 6} with RE=Y, Gd, Nd. However, these vibrational bands were characterized by large full width at half maximum, probably resulting from the long range Bi/Lu disorder and local WO{sub 6} octahedron distortions in the structure. - Graphical abstract: The average structure of BiLuWO{sub 6} determined from X-ray diffraction data can be represented by A2/m space group. Experimental Electron Diffraction patterns along the [0vw] zone axes of the monoclinic structure and associated simulated patterns show the existence of a monoclinic superstructure with space group P2 or P2/m. - Highlights: • A new monoclinic BiLuWO{sub 6} phase has been elaborated from solid-state reaction. • The space group of the monoclinic disordered average structure should be A2/m. • Transmission electron microscopy leads to a superlattice with P2/m space group. • Raman spectroscopy suggests existence of local disorder.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fabrication of shape controlled Fe{sub 3}O{sub 4} nanostructure

Shape-controlled Fe{sub 3}O{sub 4} nanostructure has been successfully prepared using polyethylene glycol as template in a water system at room temperature. Different morphologies of Fe{sub 3}O{sub 4} nanostructures, including spherical, cubic, rod-like, and dendritic nanostructure, were obtained by carefully controlling the concentration of the Fe{sup 3+}, Fe{sup 2+}, and the molecular weight of the polyethylene glycol. Transmission Electron Microscope images, X-ray powder diffraction patterns and magnetic properties were used to characterize the final product. This easy procedure for Fe{sub 3}O{sub 4} nanostructure fabrication offers the possibility of a generalized approach to the production of single and complex nanocrystalline oxide with tunable morphology.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

On the improvement of measurement accuracy of retained austenite in steel with X-ray diffraction

Highlights: • Improved procedure to determine austenite in steels with crystallographic texture • Extension to X-ray area detectors • Electropolishing is essential to get correct results. - Abstract: An improved measurement scheme for the determination of the retained austenite fraction with X-ray diffraction is extended to area detectors. The scheme reduces the error due to crystallographic texture in phase analysis of steel by averaging the results of diffraction patterns at different sample positions. The method is based on the standard ASTM E975, but it can be easily extended to other crystal structures, multi-phase materials or X-ray wavelengths. Phase transformation, induced by mechanical sample preparation, may lead to a significant reduction of the retained austenite fraction. Electropolishing before the measurement is beneficial to remove the layer affected by sample preparation.

36 MATERIALS SCIENCE↗