Search NASA⌕ Search

SEARCH · Search NASA

Results for “Electrode Engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

A Review of the Suppression of Secondary Electron Emission from the Electrodes of Multistage Collectors

A review is presented of more than 20 years of research conducted at NASA Lewis Research Center on the suppression of secondary electron emission (SEE) for the enhancement of the efficiency of vacuum electron devices with multistage depressed collectors. This paper will include a description of measurement techniques, data from measurements of SEE on a variety of materials of engineering interest and methods of surface treatment for the suppression of SEE. In the course of this work the lowest secondary electron yield ever reported was achieved for ion textured graphite, and, in a parallel line of research, the highest yield was obtained for chemical vapor deposited thin diamond films.

Dayton, James A., Jr.↗

Facile in Situ Syntheses of Cathode Protective Electrolyte Additives for High Energy Density Li-Ion Cells

Increasing the energy densities of Li-ion batteries necessitates operation of layered lithiated oxide cathodes at potentials exceeding 4 V vs Li/Li + . When continually exposed to such high potentials, these materials gradually deteriorate unless protected by sacrificial agents called electrolyte additives. During the formation cycles, these electrolyte additives decompose on the electrodes forming thin protective layers of insoluble products impeding further deleterious reactions. Some of these electrolyte additives spontaneously react when introduced into the electrolyte to yield specific surface-modifying products that alone protect the cathode; in other words, the nominal additive is the precursor and the secondary product is the protective agent. Guided by this insight, we used molecular engineering to obtain such surface-active secondary products in situ with 100% yield. Two of these electrolyte additives proved exceptional in that they delay both the impedance rise and capacity fade in the Li-ion cells. We demonstrate this protective action and scrutinize the activation of these additives in the electrolyte. As a result, by “taming” spontaneous reactions and regaining full control over the chemical structure, new avenues open to targeted synthesis of electrolyte additives extending the operation of high voltage Li-ion batteries.

25 ENERGY STORAGE↗

Toward Long-Life, Ultrahigh-Nickel Layered Oxide Cathodes for Lithium-Ion Batteries: Optimizing the Interphase Chemistry with a Dual-Functional Polymer

Boosting the Ni content in LiMO 2 (M = Ni, Co, Mn, etc.) layered oxides is a promising way to establish high-energydensity, low-cost cathodes, but the poor cathode surface stability is a daunting challenge for their practical viability. Herein, by constructing a dual-functional binder framework with a conductive polymer - polyaniline (PANI), the ultrahigh-Ni layered oxide cathode (LiNi 0.94 Co 0.06 O 2 ) exhibits significantly improved cyclability, with a capacity retention greatly increased from 47% to 81% over 1,000 cycles in full cells. It is demonstrated that the acidic species (e.g. HF) in the electrolyte can be efficiently scavenged through a protonation process of PANI, hence the cathode surface reactivity is greatly suppressed and the rock-salt phase propagation into bulk structure is considerably alleviated. Furthermore, the PANI binder system effectively prevents both the cathode-electrolyte interphase (CEI) and anode-electrolyte interphase (AEI) from degrading to a thick “triple-layer” architecture upon extensive cycling, resulting in more robust, thinner CEI and AEI with regulated interphasial chemistry. Moreover, the delocalized π-conjugated electrons along the backbone of PANI facilitate fast electron transfer and promote rate capability even at low temperatures (-20 °C). Finally, this work sheds light on rational binder engineering for developing high-energy-density lithium-ion batteries with acceptable cycle life.

25 ENERGY STORAGE↗

Boosting Fuel Cell Performance with Accessible Carbon Mesopores

We present that heavy use of scarce Pt in the electrodes poses a barrier to the application of proton exchange membrane fuel cells (PEMFCs) for transportation. Although some automakers can now commercialize fuel cell electric vehicles (FCEVs) with as little as 30 g of Pt, this is still substantially more than what incumbent internal combustion engine vehicles use (2-8 g of precious metals). A long-term target of <5 g of Pt-group metals per vehicle is probably needed to be sustainable. Since W. R. Grove’s invention of the fuel cell in 1839, most breakthroughs in fuel cell performance have been associated with an increase in the so-called three-phase interface—the interface where the reactant gas meets electrons in the solid phase and protons in the electrolyte phase. Pt is made into nanoparticles and supported on carbon black to increase the mass-specific Pt surface area and to secure large pores for reactant oxygen gas to access Pt. Solid electrolyte such as the perfluorosulfonic acid (PFSA) ionomer is blended with the catalyst to carry protons to the Pt surface. Lastly, despite a long history of maximizing the three-phase interfacial area, one must realize that an optimized three-phase interface does not equal a maximum Pt/ionomer interface area.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Low-Resistant Ion-Exchange Membranes for Energy Efficient Membrane Capacitive Deionization

Membrane capacitive deionization (MCDI) has emerged as an effective and energy efficient desalination technology for treating brackish water streams used in numerous industrial processes. Most material research studies on MCDI focus on improving the porous electrodes or using flowing electrode architectures, and little emphasis is given to the rationale design of ion-exchange membranes (IEMs) for MCDI. In this work, the ionic conductivity, permselectivity, and thickness for three different IEM chemistries (polyaliphatic, poly(arylene ether), and perfluorinated) were correlated to MCDI performance attributes: energy expended per ion removed, salt removal efficiency, and Coulombic efficiency. A 5- to 10-fold reduction in area specific resistance, which accounts for thickness and ionic conductivity, with unconventional perfluorinated and poly(arylene ether) IEMs reduced the energy expended per ion removed in MCDI by a factor of 2 when compared to conventional electrodialysis IEMs. In situ electrochemical impedance spectroscopy substantiated that thinner membranes with higher ionic conductivity helped in the reduction of energy expended per ion removed (more than 50%). Lastly, the lower than 100% Coulombic efficiency is ascribed to carbon corrosion of the porous electrodes highlighting that further improvements in MCDI do not just necessitate more appropriate membranes but corrosion resilient electrodes. KEYWORDS: Desalination, Ion-exchange membranes, Membrane capacitive deionization

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Manipulating the diffusion energy barrier at the lithium metal electrolyte interface for dendrite-free long-life batteries

Abstract Constructing an artificial solid electrolyte interphase (SEI) on lithium metal electrodes is a promising approach to address the rampant growth of dangerous lithium morphologies (dendritic and dead Li 0 ) and low Coulombic efficiency that plague development of lithium metal batteries, but how Li + transport behavior in the SEI is coupled with mechanical properties remains unknown. We demonstrate here a facile and scalable solution-processed approach to form a Li 3 N-rich SEI with a phase-pure crystalline structure that minimizes the diffusion energy barrier of Li + across the SEI. Compared with a polycrystalline Li 3 N SEI obtained from conventional practice, the phase-pure/single crystalline Li 3 N-rich SEI constitutes an interphase of high mechanical strength and low Li + diffusion barrier. We elucidate the correlation among Li + transference number, diffusion behavior, concentration gradient, and the stability of the lithium metal electrode by integrating phase field simulations with experiments. We demonstrate improved reversibility and charge/discharge cycling behaviors for both symmetric cells and full lithium-metal batteries constructed with this Li 3 N-rich SEI. These studies may cast new insight into the design and engineering of an ideal artificial SEI for stable and high-performance lithium metal batteries.

25 ENERGY STORAGE↗

Improving the fast-charging capability of NbWO-based Li-ion batteries

The discovery of Nb-W-O materials years ago marks the milestone of charging a lithium-ion battery in minutes. Nevertheless, for many applications, charging lithium-ion battery within one minute is urgently demanded, the bottleneck of which largely lies in the lack of fundamental understanding of Li + storage mechanisms in these materials. Herein, by visualizing Li + intercalated into representative Nb 16 W 5 O 55 , we find that the fast-charging nature of such material originates from an interesting rate-dependent lattice relaxation process associated with the Jahn-Teller effect. Furthermore, in situ electron microscopy further reveals a directional, [010]-preferred Li + transport mechanism in Nb 16 W 5 O 55 crystals being the “bottleneck” toward fast charging that deprives the entry of any desolvated Li + through the prevailing non-(010) surfaces. Hence, we propose a machine learning-assisted interface engineering strategy to swiftly collect desolvated Li + and relocate them to (010) surfaces for their fast intercalation. As a result, a capacity of ≈ 116 mAh g −1 (68.5% of the theoretical capacity) at 80 C (45 s) is achieved when coupled with a Li negative electrode.

batteries↗

Preliminary results of the International Fusion Materials Irradiation Facility deuteron injector

In the framework of the IFMIF-EVEDA project (International Fusion Materials Irradiation Facility-Engineering Validation and Engineering Design Activities), CEA/IRFU is in charge of the design, construction, and characterization of the 140 mA continuous deuteron injector, including the source and the low energy beam line. The electron cyclotron resonance ion source which operates at 2.45 GHz is associated with a 4-electrode extraction system in order to minimize beam divergence at the source exit. Krypton gas injection is foreseen in the 2-solenoid low energy beam line. Such Kr injection will allow reaching a high level of space charge compensation in order to improve the beam matching at the radio frequency quadrupole (RFQ) entrance. The injector construction is now completed on the Saclay site and the first plasma and beam production has been produced in May 2011. This installation will be tested with proton and deuteron beams either in pulsed or continuous mode at Saclay before shipping to Japan. In this paper, after a brief description of the installation, the preliminary results obtained with hydrogen gas injection into the plasma chamber will be reported.

43 PARTICLE ACCELERATORS↗

Simulation of a wire-cylinder-plate positive corona discharge in nitrogen gas at atmospheric pressure

In this work, we are going to perform a simulation of a wire-cylinder-plate positive corona discharge in nitrogen gas, and compare our results with already published experimental results in air for the same structure. We have chosen to simulate this innovative geometry because it has been established experimentally that it can generate a thrust per unit electrode length transmitted to the gas of up to 0.35 N/m and is also able to induce an ion wind top velocity in the range of 8-9 m/s in air. In our model, the used ion source is a small diameter wire, which generates a positive corona discharge in nitrogen gas directed to the ground electrode, after which the generated positive ions are further accelerated in the acceleration channel between the ground and cathode. By applying the fluid dynamic and electrostatic theories, all hydrodynamic and electrostatic forces that act on the considered geometries will be computed in an attempt to theoretically confirm the generated ion wind profile and also the thrust per unit electrode length. These results are important to establish the validity of this simulation tool for the future study and development of this effect for practical purposes.

42 ENGINEERING↗

Densified vertically lamellar electrode architectures for compact energy storage

As one of the most compact electrochemical energy storage systems, lithium-ion batteries (LIBs) are playing an indispensable role in the process of vehicle electrification to accelerate the shift to sustainable mobility. Making battery electrodes thicker is a promising strategy for improving the energy density of LIBs which is essential for applications with weight or volume constraints, such as electric-powered transportation; however, their power densities are often significantly restricted due to elongated and tortuous charge traveling distances. Here, we propose an effective methodology that couples bidirectional freeze-casting and compression-induced densification to create densified vertically lamellar electrode architectures for compact energy storage. The vertically lamellar architectures not only overcome the critical thickness limit for conventional electrodes but also facilitate and redistribute the lithium-ion flux enabling both high rate capability and stable cyclability. Furthermore, this proposed methodology is universal as demonstrated in various electrochemical active material systems. This study offers a facile approach that realizes simultaneous high energy and high power in high-loading battery electrodes and provides useful rationales in designing electrode architectures for scalable energy storage systems.

42 ENGINEERING↗

Conductivity and touch-sensor application for atomic layer deposition ZnO and Al:ZnO on nylon nonwoven fiber mats

Flexible electronics and wearable technology represent a novel and growing market for next generation devices. In this work, the authors deposit conductive zinc oxide films by atomic layer deposition onto nylon-6 nonwoven fiber mats and spun-cast films, and quantify the impact that deposition temperature, coating thickness, and aluminum doping have on the conductivity of the coated substrates. The authors produce aluminum doped zinc oxide (AZO) coated fibers with conductivity of 230 S/cm, which is ∼6× more conductive than ZnO coated fibers. Furthermore, the authors demonstrate AZO coated fibers maintain 62% of their conductivity after being bent around a 3 mm radius cylinder. As an example application, the authors fabricate an “all-fiber” pressure sensor using AZO coated nylon-6 electrodes. The sensor signal scales exponentially under small applied force (<50 g/cm{sup 2}), yielding a ∼10{sup 6}× current change under 200 g/cm{sup 2}. This lightweight, flexible, and breathable touch/force sensor could function, for example, as an electronically active nonwoven for personal or engineered system analysis and diagnostics.

42 ENGINEERING↗

Actinic and electron beam radiation curable water based electrode binders and electrodes incorporating same

A process for manufacturing an electrode utilizing electron beam (EB) or actinic radiation to cure the electrode binder is provided. A process is also disclosed for mixing specific actinic or EB radiation curable polymer precursors with electrode solid particles to form an aqueous mixture, application of the mixture to an electrode current collector, followed by the application of actinic or EB radiation to the current collector for curing the polymer, thereby binding the electrode binder to the current collector. Lithium ion batteries, electric double layer capacitors, and components produced therefrom are also provided.

25 ENERGY STORAGE↗

Flexible thin film solid state lithium ion batteries

Exemplary flexible thin film solid state lithium ion batteries (10) and methods for making the same are disclosed. An exemplary flexible solid state thin film electrochemical device (10) may include a flexible substrate (12), first (14) and second electrodes (18), and an electrolyte (16) disposed between the first (14) and second electrodes (18). The electrolyte (16) is disposed on the flexible substrate (12). The first electrode (14) is disposed on the electrolyte (16), and the second electrode (18) having been buried between the electrolyte (16) and the substrate (12).

25 ENERGY STORAGE↗

High efficiency iron electrode and additives for use in rechargeable iron-based batteries

An iron electrode and a method of manufacturing an iron electrode for use in an iron-based rechargeable battery are disclosed. In one embodiment, the iron electrode includes carbonyl iron powder and one of a metal sulfide additive or metal oxide additive selected from the group of metals consisting of bismuth, lead, mercury, indium, gallium, and tin for suppressing hydrogen evolution at the iron electrode during charging of the iron-based rechargeable battery. An iron-air rechargeable battery including an iron electrode comprising carbonyl iron is also disclosed, as is an iron-air battery wherein at least one of the iron electrode and the electrolyte includes an organosulfur additive.

25 ENERGY STORAGE↗

Reliable SOFC Systems

The goal of this U.S. Department of Energy (DOE) sponsored project was to advance the reliability, robustness and endurance of low-cost SOFC technology suitable for ultimate deployment in ≥100 MWe Integrated Gasification Fuel Cell (IGFC) or Natural Gas Fuel Cell (NGFC) systems capable of ≥97% CO2 capture. The ultimate SOFC program goals are ≤ 0.2% per 1000 hours power degradation over a 5-plus year stack life, high-volume (≥ 250 MW/year) stack production cost of ≤$225/kWsystem net AC, and “power block” (exclusive of fuel supply, contaminant removal, and CO2 capture subsystems) capital cost of ≤ 900/kWsystem net AC (in year 2011). To progress towards the ultimate program goals, the specific objectives of this project were to achieve an SOFC stack power degradation rate of ≤1.5% per 1000 hours in a 100 kW (125 kW Peak) Modular Power Block (MPB) stand-alone power system under thermally self-sustained normal operating conditions and to verify the prospects for high volume SOFC stack production cost below the DOE target of ≤ 225/kW. This final technical report summarizes the progress made during the project period of 36 months. Significant progress was made in the areas of cell and stack technology development, Modular Power Block (MPB) development, sub-MW MPB system development, and MW-class SOFC System Development and Costing. The work focused on areas necessary for comprehensive development of an SOFC fuel cell system, including, active cell improvement, contaminant resistance, process engineering, and development of non-repeat module components. Additionally, several custom built balance-of-plant components were designed and fabricated to support the fuel cell system. SOFC cell and stack development focused on improving cell performance and durability. Enhancements were achieved in areas of electrode stability and impurity tolerance. Additionally, several quality control techniques and tools were developed to ensure predictable and repeatable fabrication of SOFC stacks. Module development continued previous development efforts to achieve footprint reduction and higher efficiency by incorporating balance-of-plant functional equipment into the fuel cell containment module. Several improvements were made to prior design. Control and instrumentation hardware was integrated within the module for serviceability and size reduction. The design efforts culminated in a complete SOFC power plant system. The designed plant was constructed and tested at FCE. Stack and system costs were updated, reflecting advances made in this program.

20 FOSSIL-FUELED POWER PLANTS↗

Rechargeable Lithium-Air Batteries: Development of Ultra High Specific Energy Rechargeable Lithium-Air Batteries Based on Protected Lithium Metal Electrodes

BEEST Project: PolyPlus is developing the world’s first commercially available rechargeable lithium-air (Li-Air) battery. Li-Air batteries are better than the Li-Ion batteries used in most EVs today because they breathe in air from the atmosphere for use as an active material in the battery, which greatly decreases its weight. Li-Air batteries also store nearly 700% as much energy as traditional Li-Ion batteries. A lighter battery would improve the range of EVs dramatically. Polyplus is on track to making a critical breakthrough: the first manufacturable protective membrane between its lithium–based negative electrode and the reaction chamber where it reacts with oxygen from the air. This gives the battery the unique ability to recharge by moving lithium in and out of the battery’s reaction chamber for storage until the battery needs to discharge once again. Until now, engineers had been unable to create the complex packaging and air-breathing components required to turn Li-Air batteries into rechargeable systems.

ARPA-E↗