Search NASA⌕ Search

SEARCH · Search NASA

Results for “Engine Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Evaluation of fuel-borne sodium effects on a DOC-DPF-SCR heavy-duty engine emission control system: Simulation of full-useful life

Here we report that for renewable fuels to displace petroleum, they must be compatible with emissions control devices. Pure biodiesel contains up to 5 ppm Na + K and 5 ppm Ca + Mg metals, which have the potential to degrade diesel emissions control systems. This study aims to address these concerns, identify deactivation mechanisms, and determine if a lower limit is needed. Accelerated aging of a production exhaust system was conducted on an engine test stand over 1001 h using 20% biodiesel blended into ultra-low sulfur diesel (B20) doped with 14 ppm Na. This Na level is equivalent to exposure to Na at the uppermost expected B100 value in a B20 blend for the system full-useful life. During the study, NOx emissions exceeded the engine certification limit of 0.33 g/bhp-hr before the 435,000-mile requirement. Replacing aged diesel oxidation catalyst (DOC), diesel particulate filter (DPF), and selective catalytic reduction (SCR) devices with new degreened parts showed that each device contributed equally to the NOx increase. Following this systems-based evaluation, a detailed investigation of the individual components was completed. Na was determined to have minimal impact on DOC activity. For this system, it is estimated that B20-Na resulted in 50% more ash into the DPF. However, the Na did not diffuse into the cordierite DPF nor degrade its mechanical properties. The SCR degradation was found to be caused by a small amount of precious group metals (PGM) contamination that increased NH3 oxidation, and lowered NOx reduction. Therefore, we determined that the primary effect of Na in this study is through increased ash in the DPF rather than deactivation of the catalytic activity.

42 ENGINEERING↗
NASA NTRS1988

A microprocessor-based real-time simulator of a turbofan engine

A real-time digital simulator of a Pratt and Whitney F 100 engine is discussed. This self-contained unit can operate in an open-loop stand-alone mode or as part of a closed-loop control system. It can also be used in control system design and development. It accepts five analog control inputs and its sixteen outputs are returned as analog signals.

Litt, Jonathan S.↗
DOE OSTI2021

Linear and Nonlinear Solvers for Simulating Multiphase Flow within Large-Scale Engineered Subsurface Systems

Simulation of multiphase flow in the subsurface is well-known to be computationally challenging. While there have been many studies that have explored approaches to overcoming these challenges, they often utilize relatively simple case studies. In this paper, we focus on the unique numerical challenges posed by modeling large-scale engineered subsurface systems, characterized by discrete features embedded in a heterogeneous natural subsurface setting. The man-made features such as shafts, tunnels, and barriers often cause multiple challenges in modeling the domain for multiphase porous media flow. This flow scenario can have a wide range of applications such as nuclear waste repositories, enhanced recovery of a petroleum reservoir, geothermal engineering, and carbon sequestration. An example of these severe numerical challenges is the case of performance assessment (PA) for Waste Isolation Pilot Plant (WIPP), the only operating deep geological repository in the US, which simulates extreme material properties of bedded salt rock formation and extreme contrast due to open excavation next to the formation. The models have extremes not only of permeability and porosity but also of the constitutive models needed for multiphase flow; additionally, they have process models like salt creep closure reducing porosity over time, fracturing in clay and anhydrite interbeds of the bedded salt, gas generation from the waste materials, and unintentional human borehole intrusions in some scenarios. Numerical simulations require the solution of coupled systems of nonlinear PDEs; in our work, we use the open-source simulator PFLOTRAN which is based on Finite Volume discretization. The solution of the nonlinear equations requires use of the Newton-Raphson iteration at each time step, which entails the solution of the linearized Jacobian system at each iteration. The effects of all the processes (i.e., large number of unknowns, highly nonlinear constitutive relations, large contrasts in material properties in short distances) lead to an ill-conditioned Jacobian matrix that severely challenges traditional linear solver, i.e., stabilized biconjugate gradient with block Jacobi incomplete LU preconditioner (BCGS-ILU) leading to non-convergence for traditional Newton-Raphson nonlinear solver causing unacceptably long computation time for each model. This paper presents linear solvers such as constrained pressure residual (CPR) two-stage preconditioner with alternate-block-factorization (ABF) and quasi- implicit pressure and explicit saturation (QIMPES) decouplers and flexible generalized residual solver (FGMRES). The new general-purpose nonlinear solver, Newton trust-region dogleg Cauchy (NTRDC), is also introduced to resolve extreme nonlinearities in the models. We demonstrate the effectiveness of each method relative to the default BCGS-Newton solver. The two best cases had nearly 50 times speed-up and achieved completion of a simulation in 14 hours that never completed due to non-convergence with the default solver. We also investigate the strong scalability of each method and discuss some of the deficiencies found for Block Jacobi preconditioner using parallel domain decomposition, and node packing effects of modern processor architecture.

Preconditioner, Nonlinear, Porous media, Multiphas↗
NASA NTRSDate not supplied

Exploitation of a Validation Hierarchy for Modeling and Simulation

Across engineering there is an evolving need to increase reliance on physics-based simulation to develop, design and optimize engineering systems. This increased reliance on modeling and simulation has highlighted a growing need to transform the confidence that modeling and simulation analysts have in their results into credibility for systems engineers to design and field systems more quickly and with less physical testing. For isolated components of a complex system, where a single discipline may drive product design, this is less of a concern as the relationship is often straightforward and easy to explain. However, when these isolated components are integrated, and are expected to operate in a multi-disciplinary context in which safety critical systems are involved, new concepts and model assurance standards are required. In this paper we address this challenge by showing how a model validation hierarchy can be exploited to identify those model validation experiments that will contribute most to increasing confidence and credibility of modeling and simulation predictions. The approach that is adopted contains four main steps. The first step is the construction of a model validation hierarchy that links subsystems, assemblies, and components to a hierarchy of physical experiments that can be used support model validation. This hierarchy connects the concerns of systems engineers to those of the modeling and simulation analyst in a clear and logical way. The structure and content of this hierarchy is then used in a second step to establish which physical phenomena have the greatest impact on overall system performance metrics. A gap analysis technique, based upon modeling and simulation concerns, is then used to prioritize the important physical phenomenon. Unfortunately, a common outcome of such gap analyses is the identification of many important gaps and so, in the final step of our process, we advocate the use of a global sensitivity analysis as a means to complete the prioritization.

Verification and Validation↗
NASA NTRSDate not supplied

Exploitation of a Validation Hierarchy for Modeling and Simulation

Across engineering there is an evolving need to increase reliance on physics-based simulation to develop, design and optimize engineering systems. This increased reliance on modeling and simulation has highlighted a growing need to transform the confidence that modeling and simulation analysts have in their results into credibility for systems engineers to design and field systems more quickly and with less physical testing. For isolated components of a complex system, where a single discipline may drive product design, this is less of a concern as the relationship is often straightforward and easy to explain. However, when these isolated components are integrated, and are expected to operate in a multi-disciplinary context in which safety critical systems are involved, new concepts and model assurance standards are required. In this paper we address this challenge by showing how a model validation hierarchy can be exploited to identify those model validation experiments that will contribute most to increasing confidence and credibility of modeling and simulation predictions. The approach that is adopted contains four main steps. The first step is the construction of a model validation hierarchy that links subsystems, assemblies, and components to a hierarchy of physical experiments that can be used support model validation. This hierarchy connects the concerns of systems engineers to those of the modeling and simulation analyst in a clear and logical way. The structure and content of this hierarchy is then used in a second step to establish which physical phenomena have the greatest impact on overall system performance metrics. A gap analysis technique, based upon modeling and simulation concerns, is then used to prioritize the important physical phenomenon. Unfortunately, a common outcome of such gap analyses is the identification of many important gaps and so, in the final step of our process, we advocate the use of a global sensitivity analysis as a means to complete the prioritization.

Verification and Validation↗
NASA NTRS2010

A High-Fidelity Simulation of a Generic Commercial Aircraft Engine and Controller

A new high-fidelity simulation of a generic 40,000 lb thrust class commercial turbofan engine with a representative controller, known as CMAPSS40k, has been developed. Based on dynamic flight test data of a highly instrumented engine and previous engine simulations developed at NASA Glenn Research Center, this non-proprietary simulation was created especially for use in the development of new engine control strategies. C-MAPSS40k is a highly detailed, component-level engine model written in MATLAB/Simulink (The MathWorks, Inc.). Because the model is built in Simulink, users have the ability to use any of the MATLAB tools for analysis and control system design. The engine components are modeled in C-code, which is then compiled to allow faster-than-real-time execution. The engine controller is based on common industry architecture and techniques to produce realistic closed-loop transient responses while ensuring that no safety or operability limits are violated. A significant feature not found in other non-proprietary models is the inclusion of transient stall margin debits. These debits provide an accurate accounting of the compressor surge margin, which is critical in the design of an engine controller. This paper discusses the development, characteristics, and capabilities of the C-MAPSS40k simulation

May, Ryan D.↗
NASA NTRS1994

Experimental Water Droplet Impingement Data on Airfoils, Simulated Ice Shapes, an Engine Inlet and a Finite Wing

An experimental method has been developed to determine the water droplet impingement characteristics on two- and three-dimensional aircraft surfaces. The experimental water droplet impingement data are used to validate particle trajectory analysis codes that are used in aircraft icing analyses and engine inlet particle separator analyses. The aircraft surface is covered with thin strips of blotter paper in areas of interest. The surface is then exposed to an airstream that contains a dyed-water spray cloud. The water droplet impingement data are extracted from the dyed blotter paper strips by measuring the optical reflectance of each strip with an automated reflectometer. Experimental impingement efficiency data represented for a NLF (1)-0414 airfoil, a swept MS (1)-0317 airfoil, a Boeing 737-300 engine inlet model, two simulated ice shapes and a swept NACA 0012 wingtip. Analytical impingement efficiency data are also presented for the NLF (1)-0414 airfoil and the Boeing 737-300 engine inlet model.

Papadakis, M.↗
NASA NTRS1979

Simulation of liquid propellant rocket engine combustion instabilities

A simulation technique for studying the high frequency combustion instabilities of liquid propellant rocket engines has been developed and used to investigate various aspects of instability phenomena. Of importance was investigation of the significance of the method of coupling the combustion and the gas dynamics of the system. Two coupling processes were studied: linear response of the combustion process to pressure fluctuations, and the nature of the resulting instabilities; and nonlinear response of the combustion process to velocity fluctuations, and the nature of the resulting instabilities. For the combustion model studied, nonlinear (velocity) coupling was found to more closely characterize liquid propellant instabilities.

Ventrice, M. B.↗
DOE OSTI2024

NuQKD: A Modular Quantum Key Distribution Simulation Framework for Engineering Applications

Abstract An experimental Quantum Key Distribution (QKD) implementation requires advanced costly hardware, unavailable in most research environments, making protocol testing and performance evaluation complicated. This has been a major motivation for the development of QKD simulation frameworks, to allow researchers to obtain insight before proceeding into practical implementations. Several simulators have been introduced over the recent years. However, only four are publicly available, only one of which models equipment imperfections. Currently, no open‐source simulator includes all following capabilities: channel attenuation modelling, equipment imperfections and effects on key rates, estimation of elapsed time during classical and quantum‐ channel processes, use of truly random binary sequences for qubits and measurement bases, shared ‐bit fraction customization. In this paper, we present NuQKD, an open‐ source modular, intuitive simulator, featuring all the above capabilities. NuQKD establishes communication between two computer terminals, accepts custom user inputs (iterations, raw key size, attacker interception rate etc.) and evaluates the sifted key, Quantum Bit Error Rate (QBER), elapsed communication time, and more. NuQKD capabilities include optical fiber and free ‐space simulation, modeling of equipment/channel imperfections, bitstrings from True Random Number Generators, decoy‐state protocol support, and automated evaluation of performance metrics. We expect NuQKD to enable convenient and accurate representation of actual experimental conditions.

Gkouliaras, Konstantinos↗
DOE OSTI2021

Impact of Materials Properties on Higher-Temperature Engine Operation

Here, we examine the effects on materials temperatures and engine efficiency via simulations of engines operating at temperatures which exceed the thermal limits of today’s materials. Potential focus areas include high-speed, high-load operation (in the fuel-enrichment zone) as well as conditions of selective cooling at lower speeds and loads. We focus on a light-duty DISI and a heavy-duty CI engine using GT-Power. Temperature distributions within the head, block, piston, and valves were obtained from 3D FEA simulations coupled with 1D GT-Power representations of the engine’s gas flow and combustion regions. We use experimentally measured thermal properties of current commercial alloys for specific engine components, as well as candidate developmental alloys with improved temperature tolerance, to gauge the effects of materials properties on engine performance, particularly focusing on operating areas where materials which can withstand higher temperatures can enable intensified combustion conditions and increased specific output. The outcome of this work is guidance on materials selection targets and benefits as OEMs meet engine-performance needs in the coming decades, to include Class 8 line-haul freight vehicles with reduced emissions, as well as design of future near net zero-carbon light-duty range extenders for more rapid electrification of medium- and heavy-duty vehicles.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Simulation of a turbofan engine for evaluation of multivariable optimal control concepts

This paper describes the development and use of a real-time simulation of the F100-PW-100 turbofan engine. The simulation is being used in a multi-variable optimal controls research program using linear quadratic regulatory theory. The simulation is used to generate linear engine models at selected operating points and evaluate the control algorithm. The paper discusses a technique to reduce the order of the model and compares selected results between high and low order models.

Seldner, K.↗
NASA NTRS2002

Software Estimates Costs of Testing Rocket Engines

Simulation-Based Cost Model (SiCM) is a computer program that simulates pertinent aspects of the testing of rocket engines for the purpose of estimating the costs of such testing during time intervals specified by its users. A user enters input data for control of simulations; information on the nature of, and activity in, a given testing project; and information on resources. Simulation objects are created on the basis of this input. Costs of the engineering-design, construction, and testing phases of a given project are estimated from numbers and labor rates of engineers and technicians employed in each phase, the duration of each phase; costs of materials used in each phase; and, for the testing phase, the rate of maintenance of the testing facility. The three main outputs of SiCM are (1) a curve, updated at each iteration of the simulation, that shows overall expenditures vs. time during the interval specified by the user; (2) a histogram of the total costs from all iterations of the simulation; and (3) table displaying means and variances of cumulative costs for each phase from all iterations. Other outputs include spending curves for each phase.

Source record↗
NASA NTRS1984

Real-time hybrid computer simulation of a small turboshaft engine and control system

The development of an analytical model of a small turboshaft engine designed for helicopter propulsion systems is described. The model equations were implemented on a hybrid computer system to provide a real time nonlinear simulation of the engine performance over a wide operating range. The real time hybrid simulation of the engine was used to evaluate a microprocessor based digital control module. This digital control module was developed as part of an advanced rotorcraft control program. After tests with the hybrid engine simulation the digital control module was used to control a real engine in an experimental program. A hybrid simulation of the engine's electrical hydromechanical control system was developed. This allowed to vary the fuel flow and torque load inputs to the hybrid engine simulation for simulating transient operation. A steady-state data and the experimental tests are compared. Analytical model equations, analog computer diagrams, and a digital computer flow chart are included.

Hart, C. E.↗
NASA NTRS2013

Jet Engine Bird Ingestion Simulations: Comparison of Rotating to Non-Rotating Fan Blades

Bird strike events in commercial airliners are a fairly common occurrence. According to data collected by the US Department of Agriculture, over 80,000 bird strikes were reported in the period 1990-2007 in the US alone [1]. As a result, bird ingestion is an important factor in aero engine design and FAA certification. When it comes to bird impacts on engine fan blades, the FAA requires full-scale bird ingestion tests on an engine running at full speed to pass certification requirements. These rotating tests are complex and very expensive. To reduce development costs associated with new materials for fan blades, it is desirable to develop more cost effective testing procedures than full-scale rotating engine tests for material evaluation. An impact test on a non-rotating single blade that captures most of the salient physics of the rotating test would go a long way towards enabling large numbers of evaluative material screening tests. NASA Glenn Research Center has been working to identify a static blade test procedure that would be effective at reproducing similar results as seen in rotating tests. The current effort compares analytical simulations of a bird strike on various nonrotating blades to a bird strike simulation on a rotating blade as a baseline case. Several different concepts for simulating the rotating loads on a non-rotating blade were analyzed with little success in duplicating the deformation results seen in the rotating case. The rotating blade behaves as if it were stiffer than the non-rotating blade resulting in less plastic deformation from a given bird impact. The key factor limiting the success of the non-rotating blade simulations is thought to be the effect of gyroscopics. Prior to this effort, it was anticipated the difficulty would be in matching the pre-stress in the blade due to centrifugal forces Additional work is needed to verify this assertion, and to determine if a static test procedure can simulate the gyroscopic effects in a suitable manner. This paper describes the various non-rotating concepts analyzed, and demonstrates the effect believed to be gyroscopic in nature on the results.

Howard, Samuel A.↗
NASA NTRS2013

Jet Engine Bird Ingestion Simulations: Comparison of Rotating to Non-Rotating Fan Blades

Bird strike events in commercial airliners are a fairly common occurrence. According to data collected by the US Department of Agriculture, over 80,000 bird strikes were reported in the period 1990 to 2007 in the US alone (Ref. 1). As a result, bird ingestion is an important factor in aero engine design and FAA certification. When it comes to bird impacts on engine fan blades, the FAA requires full-scale bird ingestion tests on an engine running at full speed to pass certification requirements. These rotating tests are complex and very expensive. To reduce development costs associated with new materials for fan blades, it is desirable to develop more cost effective testing procedures than full-scale rotating engine tests for material evaluation. An impact test on a nonrotating single blade that captures most of the salient physics of the rotating test would go a long way towards enabling large numbers of evaluative material screening tests. NASA Glenn Research Center has been working to identify a static blade test procedure that would be effective at reproducing similar results as seen in rotating tests. The current effort compares analytical simulations of a bird strike on various non-rotating blades to a bird strike simulation on a rotating blade as a baseline case. Several different concepts for simulating the rotating loads on a non-rotating blade were analyzed with little success in duplicating the deformation results seen in the rotating case. The rotating blade behaves as if it were stiffer than the non-rotating blade resulting in less plastic deformation from a given bird impact. The key factor limiting the success of the non-rotating blade simulations is thought to be the effect of gyroscopics. Prior to this effort, it was anticipated the difficulty would be in matching the prestress in the blade due to centrifugal forces Additional work is needed to verify this assertion, and to determine if a static test procedure can simulate the gyroscopic effects in a suitable manner. This paper describes the various non-rotating concepts analyzed, and demonstrates the effect believed to be gyroscopic in nature on the results

Howard, Samuel A.↗