Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLAME”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Effects of repetitive pulsing on multi-kHz planar laser-induced incandescence imaging in laminar and turbulent flames

Planar laser-induced incandescence (LII) imaging is reported at repetition rates up to 100 kHz using a burst-mode laser system to enable studies of soot formation dynamics in highly turbulent flames. Furthermore, to quantify the accuracy and uncertainty of relative soot volume fraction measurements, the temporal evolution of the LII field in laminar and turbulent flames is examined at various laser operating conditions. Under high-speed repetitive probing, it is found that LII signals are sensitive to changes in soot physical characteristics when operating at high laser fluences within the soot vaporization regime. For these laser conditions, strong planar LII signals are observed at measurement rates up to 100 kHz but are primarily useful for qualitative tracking of soot structure dynamics. However, LII signals collected at lower fluences allow sequential planar measurements of the relative soot volume fraction with a sufficient signal-to-noise ratio at repetition rates of 10–50 kHz. Finally, guidelines for identifying and avoiding the onset of repetitive probe effects in the LII signals are discussed, along with other potential sources of measurement error and uncertainty.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Development of Criteria for Flashback Propensity in Jet Flames for High Hydrogen Content and Natural Gas Type Fuels

Due to increasingly stringent air quality requirements stationary power gas turbines have moved to lean-premixed operation, which reduces pollutant emissions but can result in flashback. Curtailing flashback can be difficult with hydrocarbon fuels and becomes even more challenging when hydrogen is used as the fuel. In fact, flashback is a key operability issue associated with low emission combustion of high hydrogen content fuels. Flashback can cause serious damage to the premixer hardware. Hence, design tools to predict flashback propensity are of interest. Such a design tool has been developed based on the data gathered by experimental study to predict boundary layer flashback using non-dimensional parameters. The flashback propensity of a premixed jet flame has been studied experimentally. Boundary layer flashback has been investigated under turbulent flow conditions at elevated pressures and temperatures (i.e. 3 atm to 8 atm and 300 K to 500 K). The data presented in this study are for hydrogen fuel at various Reynolds numbers, which are representative of practical gas turbine premixer conditions and are significantly higher than results currently available in the literature. Three burner heads constructed of different materials (stainless steel, copper, and zirconia ceramic) were used to evaluate the effect of tip temperature, a parameter found previously to be an important factor in triggering flashback. This study characterizes flashback systematically by developing a comprehensive non-dimensional model which takes into account all effective parameters in boundary layer flashback propensity. The model was optimized for new data and captures the behavior of the new results well. Further, comparison of the model with the single existing study of high pressure jet flame flashback also indicates good agreement. The model developed using the high pressure test rig is able to predict flashback tendencies for a commercial gas turbine engine and can thus serve as a design tool for identifying when flashback is likely to occur for a given geometry and condition.

03 NATURAL GAS↗

A Flame Spray Process for Cathode Materials Manufacturing for Lithium Ion Batteries

Flame (combustion) processes are the most economic ones to produce fine powders and have been used to produce pigment titanium oxide and fused silica in large volumes. In this work a flame spray pyrolysis (FSP) process has been developed to make metal oxide powders for the positive electrode materials at low cost. In particular, the work was focused on making metal oxides of NMC materials with stoichiometric compositions and desired morphologies. Our FSP is a green chemical process employing low cost biomass precursors for the battery material manufacturing. The detailed results of the synthesis, characterization, and battery testing of the NMC powder materials will be presented.

25 ENERGY STORAGE↗

Nanostructured Powders Made from Flame Spray Pyrolysis for Li-Ion Cathode

Flame processes are the most economic ones to produce fine powders and have been used to produce pigment titanium oxide and fused silica in large volumes. In this work a flame spray pyrolysis (FSP) process is used to make positive electrode materials for Li-ion battery, which is made of complex metal oxide powders, such as Li(Ni1/3Mn1/3Co1/3)O2. In particular, the work was focused on making the NMC materials with stoichiometric compositions and desired morphologies. During the pyrolysis process different morphologies can be formed, involving often powders with primary nanoparticles. Such nanostructures were found to have affected the battery performance. Detailed results of the synthesis, characterization, and battery testing of the NMC powder materials will be presented.

25 ENERGY STORAGE↗

Steady Laminar Flame for 1-Step Thermal Decomposition Model of PBX 9501

We have recently developed a new 1-step thermal decomposition model of PBX 9501 high explosive. In this report, we examine the behavior of the model in 1-D steady laminar flame calculations. In particular, the dependencies of the steady laminar flame velocity on initial pressure, thermal conductivies and parameters of the thermal decomposition model are investigated. The results of our numerical calculations are compared to available experimental data.

42 ENGINEERING↗

Heat transfer through a box beam from an impinging hydrogen flame

An analysis was performed to determine whether a hydrogen jet flame impinging on a tunnel ceiling composed of multiple prestressed steel reinforced concrete box beams could result in permanent damage to the tunnel. The lower layer of the concrete box beam was modeled to determine whether heat reaches the steel reinforcing bars and whether spalling could occur. Heat transfer analysis shows that the temperature remains constant at the location of the steel reinforcing bars after 1.3 minutes of impingement and reaches a maximum of 130°C after 5 minutes. However, assuming a constant impingement for 5 minutes is an over estimation due the existing fire model which includes conservative assumptions. Explosive spalling may occur at a thin layer (~0.05 in. at 50 seconds, 0.1 in. at 5 minutes) at the bottom surface of the concrete box beam, but the steel reinforcing bars will not be exposed to the hydrogen flame.

42 ENGINEERING↗

Evaluation of flame propagation of retrofit energy efficient wall assemblies

Leveraging safety science experience and industry relationships, UL Solutions and the International Association of Fire Fighters (IAFF) initiated a joint project in 2022 under an agreement with the US Department of Energy to evaluate the flame propagation of retrofit energy efficient wall assemblies. A draft of the protocol from the ASTM work was used to test and comparatively study various retrofit energy efficient designs to gain a better understanding of their fire behavior. The goals of this study were as follows: Develop an understanding of fire propagation across new, cost effective, and energy efficient exterior retrofit wall assemblies. Refine the flame propagation draft test method for exterior wall assemblies based on ASTM E2707. Identify conditions that create fire propagation hazards in exterior wall assemblies and educate the fire service on the findings.

42 ENGINEERING↗

Predictive Modeling of NOx Emissions from Lean Direct Injection of Hydrogen and Hydrogen/Natural Gas Blends Using Flame Imaging and Machine Learning

This research paper explores the use of machine learning to relate images of flame structure and luminosity to measured NOx emissions. Images of reactions produced by 16 aero-engine derived injectors for a ground-based turbine operated on a range of fuel compositions, air pressure drops, preheat temperatures and adiabatic flame temperatures were captured and postprocessed. The experimental investigations were conducted under atmospheric conditions, capturing CO, NO and NOx emissions data and OH* chemiluminescence images from 27 test conditions. The injector geometry and test conditions were based on a statistically designed test plan. These results were first analyzed using the traditional analysis approach of analysis of variance (ANOVA). The statistically based test plan yielded 432 data points, leading to a correlation for NOx emissions as a function of injector geometry, test conditions and imaging responses, with 70.2% accuracy. As an alternative approach to predicting emissions using imaging diagnostics as well as injector geometry and test conditions, a random forest machine learning algorithm was also applied to the data and was able to achieve an accuracy of 82.6%. This study offers insights into the factors influencing emissions in ground-based turbines while emphasizing the potential of machine learning algorithms in constructing predictive models for complex systems.

08 HYDROGEN↗

Quantification of biogenic volatile organic compounds with a flame ionization detector using the effective carbon number concept

Biogenic volatile organic compounds (BVOCs) are emitted into the atmosphere by plants and include isoprene, monoterpenes, sesquiterpenes, and their oxygenated derivatives. These BVOCs are among the principal factors influencing the oxidative capacity of the atmosphere in forested regions. BVOC emission rates are often measured by collecting samples onto adsorptive cartridges in the field and then transporting these samples to the laboratory for chromatographic analysis. One of the most commonly used detectors in chromatographic analysis is the flame ionization detector (FID). For quantitative analysis with an FID, relative response factors may be estimated using the effective carbon number (ECN) concept. The purpose of this study was to determine the ECN for a variety of terpenoid compounds to enable improved quantification of BVOC measurements. A dynamic dilution system was developed to make quantitative gas standards of VOCs with mixing ratios from 20–55 ppb. For each experiment using this system, one terpene standard was co-injected with an internal reference, n-octane, and analyzed via an automated cryofocusing system interfaced to a gas chromatograph flame ionization detector and mass spectrometer (GC/MS/FID). The ECNs of 16 compounds (14 BVOCs) were evaluated with this approach, with each test compound analyzed at least three times. The difference between the actual carbon number and measured ECN ranged from -24% to -2%. Furthermore, the difference between theoretical ECN and measured ECN ranged from -22% to 9%. Measured ECN values were within 10% of theoretical ECN values for most terpenoid compounds.

47 OTHER INSTRUMENTATION↗

Turbulent flame speeds and NOx kinetics of HHC fuels with contaminants and high dilution levels

This progress report documents the second year of the project, from October 1, 2011 through September 30, 2012. Characterization of the new turbulent flame speed vessel design was completed. Turbulence statistics of three impellers with different geometric features were measured using particle image velocimetry inside a Plexiglas model (~1:1 scale) of a cylindrical flame speed vessel (30.5 cm ID × 35.6 cm L). With four impellers arranged in a central-symmetric configuration, turbulence intensities between 1.2 and 1.7 m/s with negligible mean flow (0.1u´) were attained at the lowest fan speeds. Acceptable ranges for homogeneity and isotropy ratios of the velocity fields were set within a narrow bandwidth near unity (0.9-1.1). Homogeneity ratios were unaffected by changes to the impeller geometry, and the prototype with the higher number of blades caused the flow to become anisotropic. The integral length scale of the flow fields varied between 27 and 20 mm, which correlates well with those typically observed inside a gas turbine combustor. The mechanism to independently vary the intensity level and the integral length scale was established, where turbulence intensity level was dependent on the rotational speed of the fan, and the integral length scale decreased with increasing blade pitch angle. Ignition delay times of H₂/O₂ mixtures highly diluted with Ar and doped with various amounts of N₂O (100, 400, 1600, 3200 ppm) were measured in a shock tube behind reflected shock waves over a wide range of temperatures (940-1675 K). The pressure range investigated during this work (around 1.6, 13, and 30 atm) allows studying the effect of N₂O on hydrogen ignition at pressure conditions that have never been heretofore investigated. Ignition delay times were decreased when N₂O was added to the mixture only for the higher nitrous oxide concentrations, and some changes in the activation energy were also observed at 1.5 and 30 atm. When it occurred, the decrease in the ignition delay time was proportional to the amount of N₂O added and depended on pressure and temperature conditions. A detailed chemical kinetics model was developed using kinetic mechanisms from the literature. This model predicts well the experimental data obtained during this study and from the literature. The chemical analysis using this model showed that the decrease in the ignition delay time was mainly due to the reaction N₂O +M ⇌ N₂ + O +M which provides O atoms to strengthen the channel O + H₂ ⇌ OH + H. Ignition delay times have been measured behind reflected shock waves at 1.5, 12 and 30 atm for a mixture representative of a syngas produced from biomass (0.29659% CO / 0.29659% H₂ / 0.15748% CO₂ / 0.08924% CH₄ / 0.20997% H₂O / 0.95013% O₂ in 98% Ar (mol.%)) and for the same biomass-derived syngas mixture doped with 200 ppm of NH₃. The importance of the various constituents on the ignition delay time was investigated by comparing the results with data from various baseline mixtures (H₂/O₂/Ar, H₂/CO/O₂/Ar and H₂/CO/O₂/Ar with one of the other constituent of the syngas (i.e. CO₂, H₂O, CH₄ or NH₃)). The equivalence ratio was set to 0.5 during this study. Several recent detailed kinetics mechanisms from the literature were computed against these data, with fair agreement. Results showed that the mixture composition can have an important effect on the ignition delay time, with most of the effect being due to CH₄ addition through the reaction CH₄+OH⇌CH₃+H₂O. The ammonia impurity had very little effect on the ignition delay time over the range of conditions studied.

Petersen, Eric↗

Ignition, Flame Progation, and End-Gas Autoignition Studies of Natural Gas/ EGR Blends in a Rapid Compression Machine

The development of high efficiency, spark ignited natural gas engines is currently limited by engine knock at high power density (at high compression ratio and/or elevated boost pressures) and misfire (at lean conditions and/or high exhaust gas recirculation levels). The knock and misfire limits are further confounded by the wide variety in fuel reactivity observed in “pipeline quality” natural gas. In this study, a rapid compression machine (RCM) was used to characterize the effects of variation in natural gas fuel reactivity and exhaust gas recirculation (EGR) on homogeneous ignition delay, flame propagation rate and end-gas autoignition (EGAI) propensity for stoichiometric natural gas/oxidizer/EGR blends. Pipeline quality natural gas with variable reactivity (68 < Methane Number < 95) was simulated using mixtures of methane, ethane, and propane. EGR was simulated with mixtures of Ar, CO2, CO, and NO. EGR substitution rates were varied from 0 to 30 mass percent. Ignition delay period under homogeneous autoignition conditions was measured at compressed pressures of 24.0 to 33.1 bar and compressed temperatures of 667 to 980 K. Flame propagation rate and EGAI propensity was measured at spark-ignition pressures of 29.9 to 32.9 bar and temperatures of 721 to 782 K.

Mohr, Jeffrey↗

DNS of a Simplified Gas Turbine Premixer: Auto-Ignition and Flame Stabilization

With the increasing need for fuel-flexibility, an understanding of auto-ignition inside gas turbine premixers is crucial. Direct numerical simulation (DNS) is a great tool to reveal the fine grain details of physics inside the premixer and guide the choice of the models to use for less expensive simulations. We present numerical simulations of a simplified and downscaled premixer, with multiple air jets in rich fuel crossflow. The simulations show intense fuel-air mixing and flame-turbulence interaction. We examine flow acceleration by the incoming jets, and the combustion within the device. We observe low-temperature and high-temperature combustion signatures, and compute the flame index to quantify local stabilization modes.

combustion↗

In-Situ Species Concentration Measurements in Ammonia-Mix Flames Using FTIR Spectroscopy

Hydrogen and ammonia represent two carbon-free fuel sources that could be used in place of current fossil energy sources in combustion systems. To develop optimized ammonia combustion systems, validated modeling tools are needed. In the open literature, it has been shown that the complex chemistry associated with fuel-bound nitrogen contained in ammonia differs greatly from natural gas or hydrogen combustion. As a result, several new chemical kinetic mechanisms have been developed. Many of these mechanisms have been validated experimentally, however this has primarily focused on bulk parameters such as laminar flame speed and ignition delay time. Critically, high quality measurements of species concentrations are needed under controlled conditions which are easily represented by simple models. In this paper, direct, in-situ measurements of species concentrations and gas temperature are performed in a laminar flat-flame burner. This arrangement enables comparison with 1D model predictions, better isolating chemical kinetics from the fluid dynamics. Quantitative species concentrations are determined by absorption spectroscopy using an FTIR spectrometer. Fuel compositions representative of cracked ammonia (NH3/H2) and ammonia-natural gas (NH3/CH4) are considered for rich and lean equivalence ratios. A major focus of the paper is on the selection of spectral features for nitric oxide and ammonia and correcting for large amounts of baseline H2O absorption.

Bedick, Clinton↗

The Sensitivity of Chemical Kinetic Models on Flame Transfer Functions in High Frequency Acoustic Fluctuation Environments

This paper investigates how different chemical kinetics models are able to capture the dynamics of laminar premixed methane/air flames. In particular, this paper computes flame transfer functions and compares the performance of different global kinetic models as well as detailed kinetic models. This is accomplished using a sequence of one-dimensional incompressible simulations implemented in OpenFOAM. The detailed GRI Mech 3.0 is used as a baseline for comparison. Detailed kinetic analysis will be conducted to understand the underlying kinetics-dynamics coupling.

Girdhar, Anant↗

Combined TDLAS and chemiluminescence imaging in a flat flame burner operated with NH3/H2 blends

Ammonia is a promising hydrogen carrier due to its favorable storage and transport characteristics. However, its direct use in combustion systems is limited by low flammability and potential for high nitrogen oxide emissions. To better understand ammonia combustion, researchers conducted experiments using a flat flame burner and measured species profiles using tunable-diode-laser-absorption-spectroscopy and chemiluminescence imaging. They tested three flame conditions with different ammonia-hydrogen blends and oxygen levels. The results were compared to simulations using various kinetic mechanisms, including one that accounts for excited species chemistry. The goal is to provide direct information about species profiles in a simple system, isolating chemical kinetics from fluid dynamic effects, which can inform the development of more efficient and low-emission combustion systems using ammonia.

ammonia combustion↗

Scalar filtered mass density functions in nonpremixed turbulent jet flames

Filtered mass density functions (FMDFs) of mixture fraction and temperature are studied by analyzing experimental data obtained from one-dimensional Raman/Rayleigh/LIF measurements of nonpremixed CH{sub 4}/H{sub 2}/N{sub 2} turbulent jet flames at Reynolds numbers of 15,200 and 22,800 (DLR-A and -B). The experimentally determined FMDFs are conditioned on the Favre filtered values of the mixture fraction and its variance. Filter widths are selected as fixed multiples of the experimentally determined dissipation length scale at each measurement location. One-dimensional filtering using a top-hat filter is performed to obtain the filtered variables used for conditioning. The FMDFs are obtained by binning the mass and filter kernel weighted samples. Emphasis is placed on the shapes of the FMDFs in the fuel-rich, fuel-lean, and stoichiometric intervals for the Favre filtered mixture fraction, and low, medium, and high values for the Favre filtered mixture fraction variance. It is found that the FMDFs of mixture fraction are unimodal in samples with low mixture fraction variance and bimodal in samples with high variance. However, the FMDFs of mixture fraction at the smallest filter size studied are unimodal for all values of the variance. The FMDFs of temperature are unimodal in samples with low mixture fraction variance, and either unimodal or bimodal, depending on the mixture fraction mean, in samples with high variance. The influence of the filter size and the jet Reynolds number on the FMDFs is also considered. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A numerical study of soot aggregate formation in a laminar coflow diffusion flame

Soot aggregate formation in a two-dimensional laminar coflow ethylene/air diffusion flame is studied with a pyrene-based soot model, a detailed sectional aerosol dynamics model, and a detailed radiation model. The chemical kinetic mechanism describes polycyclic aromatic hydrocarbon formation up to pyrene, the dimerization of which is assumed to lead to soot nucleation. The growth and oxidation of soot particles are characterized by the HACA surface mechanism and pyrene-soot surface condensation. The mass range of the solid soot phase is divided into thirty-five discrete sections and two equations are solved in each section to model the formation of the fractal-like soot aggregates. The coagulation model is improved by implementing the aggregate coagulation efficiency. Several physical processes that may cause sub-unitary aggregate coagulation efficiency are discussed. Their effects on aggregate structure are numerically investigated. The average number of primary soot particles per soot aggregate n{sub p} is found to be a strong function of the aggregate coagulation efficiency. Compared to the available experimental data, n{sub p} is well reproduced with a constant 20% aggregate coagulation efficiency. The predicted axial velocity, OH mole fraction, and C{sub 2}H{sub 2} mole fraction are validated against experimental data in the literature. Reasonable agreements are obtained. Finally, a sensitivity study of the effects of particle coalescence on soot volume fraction and soot aggregate nanostructure is conducted using a coalescence cutoff diameter method. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Relevance of the Bray number in the small-scale modeling of turbulent premixed flames

The present study is devoted to the analysis of the influence of expansion phenomena on turbulent small scales in premixed reactive flows. It is shown that, under certain conditions, the expansion that takes place across wrinkled laminar flamelet can be sufficient to control the fluctuating velocity gradients and associated dissipation rate functions. These conditions are fixed by the respective values of a set of nondimensional parameters, namely the turbulence Reynolds number Re{sub T}, the Bray number, and the ratio between integral length scale of turbulence and thermal flame front thickness. A new criterion is introduced that makes it possible to delineate the influence of expansion phenomena on small-scale turbulent premixed reactive flows. The relevance of this criterion is analyzed in the light of experimental results represented in the classical diagram of combustion regime. The present analysis confirms that special care is required to represent and include the influence of expansion phenomena when using either RANS or LES closures to model turbulent premixed combustion. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗