Search NASA⌕ Search

SEARCH · Search NASA

Results for “Heat engine”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Sockeye Validation Support Using the SPHERE Facility

The engineering-scale heat pipe application Sockeye, being developed through the Nuclear En- ergy Advanced Modeling and Simulation program is concurrently undergoing code development and verification and validation activities. The Single Primary Heat Extraction and Removal Emu- lator (SPHERE) facility at Idaho National Laboratory has performed numerous sodium heat pipe experiments, one of which is modeled in this work to support Sockeye validation. Heat pipe data produced by the SPHERE facility was found to be very useful not only for Sockeye validation but also as a useful resource for model development. A Sockeye simulation performed using Sockeye’s conduction model modeled an experimental run at SPHERE and was found to be able to accurately reproduce the steady temperature distribution but revealed discrepancies in transient behavior after shutoff of the power. This effort also revealed a number of challenges of modeling an experimental setup such as SPHERE, for example, the importance of details in the setup such as possible gaps in insulation. Also, continuous collaboration between Sockeye developers and SPHERE experimentalists has been established, which allows future experiments to be refined in response to questions and challenges found by simulating earlier experiments.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Production of Diesel Engine Turbocharger Turbine from Low Cost Titanium Powder

Turbochargers in commercial turbo-diesel engines are multi-material systems where usually the compressor rotor is made of aluminum or titanium based material and the turbine rotor is made of either a nickel based superalloy or titanium, designed to operate under the harsh exhaust gas conditions. The use of cast titanium in the turbine section has been used by Cummins Turbo Technologies since 1997. Having the benefit of a lower mass than the superalloy based turbines; higher turbine speeds in a more compact design can be achieved with titanium. In an effort to improve the cost model, and develop an industrial supply of titanium componentry that is more stable than the traditional aerospace based supply chain, the Contractor has developed component manufacturing schemes that use economical Armstrong titanium and titanium alloy powders and MgR-HDH powders. Those manufacturing schemes can be applied to compressor and turbine rotor components for diesel engine applications with the potential of providing a reliable supply of titanium componentry with a cost and performance advantage over cast titanium.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Quinault Indian Nation Comprehensive Biomass Strategic Planning Project

The overall purposes of the Quinault Indian Nation’s Comprehensive Biomass Strategic Planning Project were to: (1) Identify and confirm community and tribal energy needs; (2) Conducting an inventory of sustainable biomass feedstock availability; (3) Development of a biomass energy vision statement with goals and objectives; (4) Identification and assessment of biomass options for both demand-side and supply side that are viable to the Quinault Indian Nation (QIN); and (5) Developing a long-term biomass strategy consistent with the long-term overall energy goals of the QIN. This Comprehensive Biomass Strategic Planning Project is consistent with the QIN’s prior two-year DOE Renewable Energy Study from 2004 through 2006. That study revealed that the most viable options to the QIN’s renewable energy options were biomass and energy efficiency best practices. QIN's Biomass Strategic Planning Project is focused on using forest slash in chipped form as feedstock for fuel pellet manufacturing in support of a tribal biomass heating facility. This biomass heating facility has been engineered and designed to heat existing tribal facilities as well as tribal facilities currently being planned including a new K-12 School.

09 BIOMASS FUELS↗

CRADA Number NFE-17-06866 with Active Energy Systems, Inc. (CRADA Final Report)

Cooperative Research and Development Agreement (CRADA) NFE-17-06866 between Oak Ridge National Laboratory (ORNL) and Active Energy Systems Inc. (AES) focused on studying and modeling a low cost, high efficiency energy storage technology. The successful development of low-cost, high-efficiency energy storage is a significant bottleneck in the implementation of intermittent renewable energy sources such as wind and solar. AES is a startup company developing a heat exchange technology to utilize a low-temperature phase change material (PCM). The work done under this CRADA explored this technology’s ability to augment a heat pump/heat engine device to convert electricity into thermal energy and vice versa, operating to complement the needs of the electric grid. Modeling, design and development of a prototype to prove the technology was successful, but current production economics and market demand make further exploration undesirable.

25 ENERGY STORAGE↗

Biodiesel Handling and Use Guide: Sixth Edition

This document serves as background and a guide for those who blend, distribute, and/or use biodiesel and biodiesel blends. It provides basic information on the proper and safe use of biodiesel in compression ignition engines, home heating oil systems, boilers, and other applications. This guide is intended to help users, fleets, blenders, distributors, and others understand handling and use of biodiesel and biodiesel blends. Information on the environmental benefits of biodiesel is also provided.

09 BIOMASS FUELS↗

Refining NEAMS MARVEL Reactor Model Accuracy

This report outlines the progress of Idaho National Laboratory (INL) in improving the fidelity of the multiphysics model of the Microreactor Applications Research Validation and Evaluation (MARVEL) reactor developed in FY24. The multiphysics model firstly developed in FY24 leverages three single-physics models coupled via the MOOSE’s MultiApps and Transfer systems. The first single-physics model, that functions as the driver application, leverages Griffin to model the neutron transport in the core through the discontinuous finite element (DFEM) discrete ordinates solver (SN). The second single-physics model uses BISON to compute the solid temperature in the reactor. Finally, the System Analysis Module (SAM) was used to model the flow of the sodium-potassium eutectic in the primary loop. In this report we detail the following improvement and enhancements: • An updated mesh leveraging the latest feature in the reactor module (see Section 3.1.).

42 - ENGINEERING↗

Assembly and comparison of available solar hot water system reliability databases and information.

Solar hot water (SHW) systems have been installed commercially for over 30 years, yet few quantitative details are known about their reliability. This report describes a comprehensive analysis of all of the known major previous research and data regarding the reliability of SHW systems and components. Some important conclusions emerged. First, based on a detailed inspection of ten-year-old systems in Florida, about half of active systems can be expected to fail within a ten-year period. Second, valves were identified as the probable cause of a majority of active SHW failures. Third, passive integral and thermosiphon SHW systems have much lower failure rates than active ones, probably due to their simple design that employs few mechanical parts. Fourth, it is probable that the existing data about reliability do not reveal the full extent of fielded system failures because most of the data were based on trouble calls. Often an SHW system owner is not aware of a failure because the backup system silently continues to produce hot water. Thus, a repair event may not be generated in a timely manner, if at all. This final report for the project provides all of the pertinent details about this study, including the source of the data, the techniques to assure their quality before analysis, the organization of the data into perhaps the most comprehensive reliability database in existence, a detailed statistical analysis, and a list of recommendations for additional critical work. Important recommendations include the inclusion of an alarm on SHW systems to identify a failed system, the need for a scientifically designed study to collect high-quality reliability data that will lead to design improvements and lower costs, and accelerated testing of components that are identified as highly problematic.

14 SOLAR ENERGY↗

Refractory thermal insulation for smooth metal surfaces

To protect rocket metal surfaces from engine exhaust heat, a refractory thermal insulation mixture, which adheres to smooth metals, has been developed. Insulation protection over a wide temperature range can be controlled by thickness of the applied mixture.

Source record↗

Aero-acoustic performance characteristics of duct burning turbofan exhaust nozzles

A recent experimental investigation has identified the aero/acoustic characteristics of exhaust nozzles for duct heating turbofan engines over a range of simulated flow conditions. Jet noise and performance levels are summarized for a series of coannular nozzles representing both acoustically suppressed and unsuppressed designs operating in a static environment. The basic coannular nozzles were found to provide inherent noise suppression. Multi-element suppressor nozzles provided additional noise suppression, but with appreciable thrust loss. The impact of these results on the advanced supersonic transport studies is also presented, indicating potentially large reductions in take-off gross weight or community noise footprints.

Kozlowski, H.↗

Projection of distributed-collector solar-thermal electric power plant economics to years 1990-2000

A preliminary comparative evaluation of distributed-collector solar thermal power plants was undertaken by projecting power plant economics of selected systems to the 1990 to 2000 time frame. The selected systems include: (1) fixed orientation collectors with concentrating reflectors and vacuum tube absorbers, (2) one axis tracking linear concentrator including parabolic trough and variable slat designs, and (3) two axis tracking parabolic dish systems including concepts with small heat engine-electric generator assemblies at each focal point as well as approaches having steam generators at the focal point with pipeline collection to a central power conversion unit. Comparisons are presented primarily in terms of energy cost and capital cost over a wide range of operating load factors. Sensitvity of energy costs for a range of efficiency and cost of major subsystems/components is presented to delineate critical technological development needs.

Fujita, T.↗

Methanol decomposition bottoming cycle for IC engines

This paper presents the concept of methanol decomposition using engine exhaust heat, and examines its potential for use in the operation of passenger cars, diesel trucks, and diesel-electric locomotives. Energy economy improvements of 10-20% are calculated over the representative driving cycles without a net loss in power. Some reductions in exhaust emissions are also projected.

Purohit, G.↗

Steam bottoming cycle for an adiabatic diesel engine

Steam bottoming cycles using adiabatic diesel engine exhaust heat which projected substantial performance and economic benefits for long haul trucks were studied. Steam cycle and system component variables, system cost, size and performance were analyzed. An 811 K/6.90 MPa state of the art reciprocating expander steam system with a monotube boiler and radiator core condenser was selected for preliminary design. The costs of the diesel with bottoming system (TC/B) and a NASA specified turbocompound adiabatic diesel with aftercooling with the same total output were compared, the annual fuel savings less the added maintenance cost was determined to cover the increase initial cost of the TC/B system in a payback period of 2.3 years. Steam bottoming system freeze protection strategies were developed, technological advances required for improved system reliability are considered and the cost and performance of advanced systes are evaluated.

Poulin, E.↗

Corrosion of SiC by Molten Salt

Advanced ceramic materials considered for wide range of applications as in gas turbine engines and heat exchangers. In such applications, materials may be in corrosive environments that include molten salts. Very corrosive to alloys. In order to determine extent of problem for ceramic materials, corrosion of SiC by molten salts studied in both jet fuel burners and laboratory furnaces. Surface of silicon carbide corroded by exposure to flame seeded with 4 parts per million of sodium. Strength of silicon carbide decreased by corrosion in flame and tube-furnace tests.

Jacobson, Nathan S.↗

Aluminum Alloys for High Temperatures

New Al/Li alloys processed by rapid solidification show greatly improved strength-to-density ratios. Alloys suitable substitutes for heavier titanium alloys and weaker aluminum alloys in high-performance aircraft, bombers, and transports. Also suitable for use in high-performance-aircraft structures heated by engines and normally constructed from titanium alloys.

Meschter, Peter J.↗