Search NASA⌕ Search

SEARCH · Search NASA

Results for “Injections”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Mitigation of divertor heat flux by high-frequency ELM pacing with non-fuel pellet injection in DIII-D

Experiments have been conducted on DIII-D investigating high repetition rate injection of non-fuel pellets as a tool for pacing Edge Localized Modes (ELMs) and mitigating their transient divertor heat loads. Effective ELM pacing was obtained with injection of Li granules in different H-mode scenarios, at frequencies 3–5 times larger than the natural ELM frequency, with subsequent reduction of strike-point heat flux. However, in scenarios with high pedestal density (~6 × 10 19 m –3 ), the magnitude of granule triggered ELMs shows a broad distribution, in terms of stored energy loss and peak heat flux, challenging the effectiveness of ELM mitigation. Furthermore, transient heat-flux deposition correlated with granule injections was observed far from the strike-points. As a result, field line tracing suggest this phenomenon to be consistent with particle loss into the mid-plane far scrape-off layer, at toroidal location of the granule injection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Modeling of fault activation and seismicity by injection directly into a fault zone associated with hydraulic fracturing of shale-gas reservoirs

We conducted three-dimensional coupled fluid-flow and geomechanical modeling of fault activation and seismicity associated with hydraulic fracturing stimulation of a shale-gas reservoir. We simulated a case in which a horizontal injection well intersects a steeply dip- ping fault, with hydraulic fracturing channeled within the fault, during a 3-hour hydraulic fracturing stage. Consistent with field observations, the simulation results show that shale-gas hydraulic fracturing along faults does not likely induce seismic events that could be felt on the ground surface, but rather results in numerous small microseismic events, as well as aseismic deformations along with the fracture propagation. The calculated seismic moment magnitudes ranged from about -2.0 to 0.5, except for one case assuming a very brittle fault with low residual shear strength, for which the magnitude was 2.3, an event that would likely go unnoticed or might be barely felt by humans at its epicenter. The calculated moment magnitudes showed a dependency on injection depth and fault dip. We attribute such dependency to variation in shear stress on the fault plane and associated variation in stress drop upon reactivation. Our simulations showed that at the end of the 3-hour injection, the rupture zone associated with tensile and shear failure extended to a maximum radius of about 200 m from the injection well. The results of this modeling study for steeply dipping faults at 1000 to 2500 m depth is in agreement with earlier studies and field observations showing that it is very unlikely that activation of a fault by shale-gas hydraulic fracturing at great depth (thousands of meters) could cause felt seismicity or create a new flow path (through fault rupture) that could reach shallow groundwater resources.

54 ENVIRONMENTAL SCIENCES↗

Investigation of post-injection strategies for diesel engine Catalyst Heating Operation using a vapor-liquid-equilibrium-based spray model

Most multidimensional engine simulations spend much time solving for non-equilibrium spray dynamics (atomization, collision, vaporization). However, their accuracy is limited by significant grid dependency, and the need for extensive calibration. This is critical for modeling cold-start diesel fuel post injections, which occur at low temperatures and pressures, far from typical model validation ranges. At the same time, resolving micron-scale spray phenomena would render full Eulerian multiphase calculations prohibitive. In this study, an improved phase equilibrium based approach was implemented and assessed for simulating diesel catalyst heating operation strategies. A phase equilibrium solver based on the model by Yue and Reitz [1] was implemented: a fully multiphase CFD solver is employed with an engineering-size engine grid, and fuel injection is modeled using the standard Lagrangian parcels approach. Mass and energy from the liquid parcels are released to the Eulerian multiphase mixture according to an equilibrium-based liquid jet model. An improved phase equilibrium solver was developed to handle large real-gas mixtures such as those from accurate chemical kinetics mechanisms. The liquid-jet model was improved such that momentum transfer to the Eulerian solver better reproduces the physical spray jet structure. Validation of liquid/vapor penetration predictions showed that the model yields accurate results with very limited tuning and low sensitivity to the few calibration constants. In-cylinder simulations of diesel catalyst heating operation strategies showed that capturing spray structure is paramount when short, transient injection pulses and low temperatures are present. Furthermore, the EP model provides improved predictions of post-injection spray structure and ignitability, while conventional spray modeling does not capture the increase of liquid penetration during the expansion stroke. Finally, the only important EP model calibration constant, Cliq, does not affect momentum transfer, but it changes the local charge cooling distribution through the local energy transfer, which makes it candidate to additional research. The results confirm that non-equilibrium spray processes do not need to be resolved in engineering simulations of high-pressure diesel sprays.

42 ENGINEERING↗

Pneumatic Microvalve-Based Hydrodynamic Sample Injection for High-Throughput, Quantitative Zone Electrophoresis in Capillaries

A hybrid microchip/capillary CE system was developed to allow unbiased and lossless sample loading and high throughput repeated injections. This new hybrid CE system consists of a polydimethylsiloxane (PDMS) microchip sample injector featuring a pneumatic microvalve that separates a sample introduction channel from a short sample loading channel and a fused silica capillary separation column that connects seamlessly to the sample loading channel. The sample introduction channel is pressurized such that when the pneumatic microvalve opens briefly, a variable-volume sample plug is introduced into the loading channel. A high voltage for CE separation is continuously applied across the loading channel and the fused silica capillary separation column. Analytes are rapidly separated in the fused silica capillary with high resolution. High sensitivity MS detection after CE separation is accomplished via a sheathless CE/ESI-MS interface. The performance evaluation of the complete CE/ESI-MS platform demonstrated that reproducible sample injection with well controlled sample plug volumes could be achieved by using the PDMS microchip injector. The absence of band broadening from microchip to capillary indicated a minimum dead volume at the junction. The capabilities of the new CE/ESI-MS platform in performing high throughput and quantitative sample analyses were demonstrated by the repeated sample injection without interrupting an ongoing separation and a good linear dependence of the total analyte ion abundance on the sample plug volume using a mixture of peptide standards. The separation efficiency of the new platform was also evaluated systematically at different sample injection times, flow rates and CE separation voltages.

Eletrophoresis↗

Modeling Ethanol-Blend Fuel Sprays under Direct-Injection Spark-Ignition Engine Conditions

Computational modeling of fuel-injection and fuel-impingement processes was carried out to provide insight into previous experimental results obtained from a direct-injection spark-ignition research engine operated with various ethanol and aromatic fuel blends. Seven model fuels were evaluated using both single- and split-injection strategies. Model results showed that droplet vaporization enriched the concentrations of aromatic species in the liquid phase, especially those with low vapor pressure, and ethanol-containing fuels altered droplet sizes and led to increased liquid-phase mass in the cylinder. For the spray-modeling conditions studied, most of the injected fuel remained in the liquid phase, which would be expected to result in more fuel impingement on cylinder or piston surfaces. Fuel impinging on lower cylinder-temperature surfaces was found to create wall films that could interact with the piston during the compression stroke. Fuel impinging on hotter piston-temperature surfaces vaporized more readily, but for fuels with high ethanol and aromatic content, wall films remained and were highly concentrated with lower vapor pressure and aromatic compounds. These films could lead to pool fires during combustion and therefore significant particulate matter emissions.

BIOMASS FUELS,INORGANIC, ORGANIC, PHYSICAL, AND AN↗

Efficient Photoinduced Charge Injection from Chemical-Bath Deposited CdS into Mesoporous TiO2 Probed with Time-Resolved Microwave Conductivity

We use the contactless time-resolved microwave conductivity (TRMC) technique to investigate the photoconductance of CdS-coated mesoporous TiO2 and ZrO2. The CdS domains were grown directly on the surface of the oxide by a chemical bath deposition method. Mobile charge carriers are generated with a low yield following photoexcitation of CdS grown on ZrO2; there is no injection into the oxide and the short-lived photoconductance signal is attributed to the hole in CdS. In contrast, illumination of CdS domains grown on TiO2 results in very efficient electron injection into the TiO2 nanoparticles, producing long-lived charge carriers. We show that the quantum yield for electron injection into TiO2 per photon absorbed by the CdS sensitizer is close to unity. The photoconductance action spectrum follows the absorption of the CdS domains, which indicates that the charge injection efficiency does not depend on wavelength in the range where the CdS absorbs (425-550 nm).

absorption↗

The Seismic Response to Injected Carbon Dioxide: Comparing Observations to Estimates Based Upon Fluid Flow Modeling

Time-lapse seismic amplitude differences and travel time shifts, obtained while monitoring enhanced oil recovery at Cranfield, Mississippi, reveal coherent changes that are associated with the injection of carbon dioxide. Rock physics modeling highlights the importance of the oil, brine, and gas content of pore fluids prior to the injection of carbon dioxide. For example, compressional velocity changes due to the injection of carbon dioxide can drop from 300 m/s to less than 100 m/s as the percentage of oil increases from 1% to 50%. Predictions based upon a new technique for modeling wave propagation in a poroelastic medium containing an arbitrary number of fluids, coupled with multicomponent numerical reservoir modeling at Cranfield, reproduce the general pattern of observed seismic amplitude changes and travel time shifts. In particular, time-lapse amplitude changes suggest a significant and widespread lowering of compressional velocities due to the injection of CO 2 into an aquifer bounding the oil rim of the reservoir. It appears that the large-scale variations in preexisting pore fluid content have a major influence on seismic velocity changes, even in the highly heterogeneous reservoir at Cranfield.

58 GEOSCIENCES↗

Basement Fault Reactivation by Fluid Injection Into Sedimentary Reservoirs: Poroelastic Effects

Abstract To investigate mechanisms of seismic fault reactivation in crystalline basement in response to fluid injection in overlying sedimentary reservoirs, we conducted three‐dimensional finite element simulations to assess the effects of direct pore pressure communication and indirect poroelastic stress transfer on the change in Coulomb failure stress of favorably oriented faults of varying permeability structure in normal, strike‐slip, and reverse faulting stress regimes. We demonstrate that the direct pore pressure effect transmitted along a hydraulically conductive fault exceeds the indirect poroelastic effect, but alone is insufficient for fault reactivation in the basement. The poroelastic effect on the Coulomb failure stress results from induced normal tractions and, to a lesser extent, from induced shear tractions that relate to the flexing of the fault as the reservoir expands poroelastically with fluid injection. Assuming a higher Biot coefficient for reservoir over basement rock as previously reported, the combined direct pore pressure and indirect poroelastic effects result in reactivation of hydraulically conductive faults in the basement in normal and strike‐slip faulting stress regimes and in the reservoir in reverse faulting regimes. Sealing normal faults that are not preferentially conductive also preferentially reactivate in the reservoir. These findings apply to injection in either hanging or footwall of normal and reverse faults. Reducing the contrast in Biot coefficient between reservoir and basement favors fault reactivation in the reservoir for injection in the footwall in normal faulting stress regimes. These simulations demonstrate that geomechanical models without coupled poroelasticity underestimate the potential of fault reactivation in crystalline basement.

Fan, Zhiqiang↗

Nitrogen-Driven Chromatographic Separation During Gas Injection Into Hydrate-Bearing Sediments

Hydrates are solid phases composed of water cages enclosing gas molecules that may host large quantities of recoverable natural gas and may serve to sequester CO 2 on geological time scales. Most hydrate studies focus on hydrates containing a single gas component, such as CH 4 or CO 2 . Yet, there are several settings in which multiple components form hydrate mixtures, or mixed hydrates, including a subsurface injection technique that claims to simultaneously recover CH 4 and sequester CO 2 called “guest molecule exchange.” Here, we combine multicomponent phase behavior for hydrate-forming systems with a multiphase fluid flow simulator to understand the evolution of hydrate and nonhydrate phases during subsurface injection. We simulate various scenarios for systems composed of H 2 O, CH 4 , CO 2 , and N 2 . Our study probes the impact of injection composition, initial reservoir composition, and transport of each component through the model domain. We observe chromatographic separation from the combined effect of compositional partitioning in each phase, variable flow speed of each phase, and compositional dependence of phase stabilities. We show that N 2 drives chromatographic separation to create a CH 4 -free zone and a CO 2 -free zone that are connected by a continuous N 2 -dominated vapor phase. While our results are theoretical and should be validated experimentally, they imply that guest molecule exchange acts as two sequential processes rather than as a simultaneous process. Furthermore, they show that injections into reservoirs with and without free water have vastly different behaviors, which has implications for the interpretation of the guest molecule exchange field test and various laboratory studies.

54 ENVIRONMENTAL SCIENCES↗

High‐Latitude Stratospheric Aerosol Injection to Preserve the Arctic

Abstract Stratospheric aerosol injection (SAI) has been shown in climate models to reduce some impacts of global warming in the Arctic, including the loss of sea ice, permafrost thaw, and reduction of Greenland Ice Sheet (GrIS) mass; SAI at high latitudes could preferentially target these impacts. In this study, we use the Community Earth System Model to simulate two Arctic‐focused SAI strategies, which inject at 60°N latitude each spring with injection rates adjusted to either maintain September Arctic sea ice at 2030 levels (“Arctic Low”) or restore it to 2010 levels (“Arctic High”). Both simulations maintain or restore September sea ice to within 10% of their respective targets, reduce permafrost thaw, and increase GrIS surface mass balance by reducing runoff. Arctic High reduces these impacts more effectively than a globally focused SAI strategy that injects similar quantities of SO 2 at lower latitudes. However, Arctic‐focused SAI is not merely a “reset button” for the Arctic climate, but brings about a novel climate state, including changes to the seasonal cycles of Northern Hemisphere temperature and sea ice and less high‐latitude carbon uptake relative to SSP2‐4.5. Additionally, while Arctic‐focused SAI produces the most cooling near the pole, its effects are not confined to the Arctic, including detectable cooling throughout most of the northern hemisphere for both simulations, increased mid‐latitude sulfur deposition, and a southward shift of the location of the Intertropical Convergence Zone. For these reasons, it would be incorrect to consider Arctic‐focused SAI as “local” geoengineering, even when compared to a globally focused strategy.

Lee, Walker Raymond↗

The Shortwave Radiative Flux Response to an Injection of Sea Salt Aerosols in the Gulf of Mexico

We report marine cloud brightening (MCB) has been proposed as a potential means of geoengineering the climate, temporarily providing cooling to offset some of the effects of climate change. Marine sky brightening (MSB), involving the direct scattering of sunlight from sea salt injection into the marine boundary layer, has been proposed as an additional geoengineering method that could work in areas that are not regularly cloudy. Here, we use a regional atmospheric model to simulate MCB and MSB over the Gulf of Mexico and nearby land, a highly populated and economically important region that is not characterized by persistent marine stratocumulus cloud cover. Injection of sea salt in the Aitken mode from a region in the central Gulf of Mexico equivalent to 10.8 Tg yr -1 produces an upwards 8.4 W m -2 radiative flux change across the region at the top of the atmosphere, largely due to cloud property changes. Comparatively, a similar mass injection in the accumulation mode produces a 3.1 W m -2 radiative flux change driven primarily by direct scattering. Injection of even larger particles produces a much smaller radiative flux change. Shortwave flux changes due to clouds are largely driven by an increase in cloud droplet number concentration and an increase in cloud liquid water path (each contributing about 45% to the flux change), with a much lower contribution from cloud fraction changes (10%).

54 ENVIRONMENTAL SCIENCES↗

Control Mechanisms for Self‐Sealing in Activated Clay‐Rich Faults Through Controlled Hydraulic Injection Experiment

Abstract In a high‐pressure injection fault activation experiment conducted at the Mont Terri underground research laboratory in Switzerland, the transmissivity of the Opalinus Clay fault significantly increased due to opening and shearing. The fluid injection, spanning a few hours, generated a 10 m radius fault activation patch. Subsequent pressure pulse tests conducted bi‐weekly for a year revealed the gradual return of fault transmissivity to its initial state. The study utilized fluid pressure decay analysis, optical fiber monitoring, continuous active source seismic measurements and borehole displacement sensors for measuring fault displacements. The fault zone exhibited a dilation of approximately 1.4 mm, associated with both normal and tangential movements during activation, resulting in a sudden transmissivity increase from 1 × 10 −12 to 3.2 × 10 −7 m 2 /s. Early post‐activation, transient compaction and the subsequent slow compaction were observed, transitioning to an extension regime. The pressure pulse tests demonstrated a rapid transmissivity drop by more than two orders of magnitude within the first 10 days, followed by a gradual and less pronounced decrease. Plastic shear and compaction dominated the transmissivity evolution until 70 days after injection ended, followed by a period where additional factors, such as clay mineral swelling, influenced the behavior. Extrapolation suggested a sealing process taking at least 50 years after the initial activation. Plain Language Summary A field‐scale fault activation experiment offers valuable insights into the elasto‐plastic processes governing the sealing of shale faults. The experiment reveals a rapid increase in the fault's transmissivity by approximately five orders of magnitude during activation. Subsequent observations show a gradual transmissivity decrease by about three orders of magnitude post‐activation, with slow long‐term plastic shear and compaction of the fault competing against secondary processes, notably clay mineral swelling. All conceptual models employed to interpret these field data converge on the estimation that the fault's return to its initial low transmissivity state would require a minimum of 50 years. Key Points High‐pressure injection fault activation experiment at the Mont Terri underground research laboratory Continuous transmissivity measurements record self‐sealing inside a clay‐rich fault zone Transmissivity undergoes a phase of domination by slow plastic compaction and shearing during the initial post‐activation period, with mineral swelling exerting its influence over the long term

Guglielmi, Yves↗

High-throughput injection-acceleration of electron bunches from a linear accelerator to a laser wakefield accelerator

Plasma-based accelerators (PBAs) driven by either intense lasers (laser wakefield accelerators, LWFAs) or particle beams (plasma wakefield accelerators, PWFAs), can accelerate charged particles at extremely high gradients compared to conventional radio-frequency (RF) accelerators. In the past two decades, great strides have been made in this field, making PBA a candidate for next-generation light sources and colliders. However, these challenging applications necessarily require beams with good stability, high quality, controllable polarization and excellent reproducibility. To date, such beams are generated only by conventional RF accelerators. As such, it is important to demonstrate the injection and acceleration of beams first produced using a conventional RF accelerator, by a PBA. In some recent studies on LWFA staging and external injection-acceleration in PWFA only a very small fraction (from below 0.1% to few percent) of the injected charge (the coupling efficiency) was accelerated. For future colliders where beam energy will need to be boosted using multiple stages, the coupling efficiency per stage must approach 100%. Here we report the first demonstration of external injection from a photocathode-RF-gun-based conventional linear accelerator (LINAC) into a LWFA and subsequent acceleration without any significant loss of charge or degradation of quality, which is achieved by properly shaping and matching the beam into the plasma structure. Furthermore, this is an important step towards realizing a high-throughput, multi-stage, high-energy, hybrid conventional-plasma accelerator.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Comprehensive analysis of disruption mitigation methods using gas and pellet-like injections in ITER-like Tokamaks

Abstract Inert-gas shielding could be an effective mechanism for protection of plasma facing surfaces (PFS) against plasma particles impact and photon radiation heat loads during transient events in fusion devices. Neutral gas injection is one promising way to mitigate erosion of tokamak components and contamination. The objective of this work is to study and optimize mitigation methods using neutral gas and pellet-like injections to decrease the heat load to the divertor surfaces and to prevent vaporization of the various internal surfaces due to transient events in ITER-like devices. The integrated self-consistent models implemented in the HEIGHTS package was used for detailed analysis of the potential secondary plasma generation from the injected inert gas, its radiative characteristics, and shielding effectiveness. We varied the density, size, and location of an argon gas cloud to minimize the disruption energy deposited into the divertor components. We also investigated innovative ways for minor changes in ITER-like internal design to mitigate disruptions. We found the optimum parameters to fully protect ITER tokamak surfaces from erosion and vaporization during plasma instabilities. This preliminary analysis showed that using Ar gas injection methods could lead to enhancement in components lifetime in ITER-like and future DEMO devices with minor design changes.

Science & Technology - Other Topics↗

In-Situ TEM Visualization Of Vacancy Injection And Chemical Partition During Oxidation Of Ni-Cr Nanoparticles

Oxidation of alloy often involves chemical partition and injection of vacancies. Chemical partition is the consequence of selective oxidation, while injection of vacancies is associated with the differences of diffusivity of cations and anions. It is far from clear as how the injected vacancies behave during oxidation of metal. Using in-situ transmission electron microscopy, we captured unprecedented details on the collective behavior of injected vacancies during oxidation of metal, featuring an initial multi-site oxide nucleation, vacancy supersaturation, nucleation of a single cavity, sinking of vacancies into the cavity and accelerated oxidation of the particle. High sensitive energy dispersive x-ray spectroscopy mapping reveals that Cr is preferentially oxidized even at the initial oxidation, leading to a structure that Cr oxide is sandwiched near the inner wall of the hollow particle. The work provides a general guidance on tailoring of nanostructured materials involving multi-ion exchange such as core-shell structured composite nanoparticles.

Environmental Molecular Sciences Laboratory↗

Model simulations of continuous ion injection into electron-beam ion source trap with slanted electrostatic mirror

The efficiency of trapping ions in an electron-beam ion source (EBIS) is of primary importance for many applications requiring operations with externally produced ions: RIA breeders, ion sources, and traps. At the present time, the most popular method of ion injection is pulsed injection, when short bunches of ions get trapped in a longitudinal trap while traversing the trap region. Continuous trapping is a challenge for EBIS devices because mechanisms which reduce the longitudinal ion energy per charge in a trap (cooling with residual gas, energy exchange with other ions, and ionization) are not very effective, and accumulation of ions is slow. A possible approach to increase trapping efficiency is to slant the mirror at the end of the trap which is opposite to the injection end. A slanted mirror will convert longitudinal motion of ions into transverse motion, and, by reducing their longitudinal velocity, prevent these ions from escaping the trap on their way out. The trade-off for the increased trapping efficiency this way is an increase in the initial transverse energy of the accumulated ions. The slanted mirror can be realized if the ends of two adjacent electrodes, drift tubes, which act as an electrostatic mirror, are machined to produce a slanted gap, rather than an upright one. Applying different voltages to these electrodes will produce a slanted mirror. The results of two-dimensional (2D) and three-dimensional (3D) computer simulations of the ion injection into an EBIS are presented using simplified models of an EBIS with conical (2D simulations) and slanted (3D simulations) mirror electrodes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Measurement of heating laser injection time to imploded core plasma by using x-ray framing camera

A simultaneous measurement of imploded core plasma and injection time of heating laser is conducted by using an x-ray framing camera (XFC). The experiments are performed using Gekko XII laser system for implosion of the deuterated polystyrene (CD) plastic shell target and Peta Watt (PW) laser system for heating. The time of PW laser injection is observed as the bright zone in the XFC image. The measured x-ray intensity profiles fit the Gaussian profiles well. The calculations of microchannel plate by using dynode model explain these broadened temporal profiles qualitatively. The peak position of fitted x-ray intensity profile is almost in agreement with the time when the high energy x ray is observed by x-ray streak camera. Moreover, the peak position is delayed corresponding to the delayed setting of PW laser injection time. From these results, it is concluded that we can estimate the heating laser injection time with resolution of the order of 10 ps by using XFC.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Optimization of Micro Metal Injection Molding By Using Grey Relational Grade

Micro metal injection molding ({mu}MIM) which is a variant of MIM process is a promising method towards near net-shape of metallic micro components of complex geometry. In this paper, {mu}MIM is applied to produce 316L stainless steel micro components. Due to highly stringent characteristic of {mu}MIM properties, the study has been emphasized on optimization of process parameter where Taguchi method associated with Grey Relational Analysis (GRA) will be implemented as it represents novel approach towards investigation of multiple performance characteristics. Basic idea of GRA is to find a grey relational grade (GRG) which can be used for the optimization conversion from multi objectives case which are density and strength to a single objective case. After considering the form 'the larger the better', results show that the injection time(D) is the most significant followed by injection pressure(A), holding time(E), mold temperature(C) and injection temperature(B). Analysis of variance (ANOVA) is also employed to strengthen the significant of each parameter involved in this study.

36 MATERIALS SCIENCE↗