Search NASA⌕ Search

SEARCH · Search NASA

Results for “Model Form”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Analyzing Mechanical integrity of Microwave resonant Cavity flowmeter

The microwave resonant cavity flow sensor has been proposed to address the difficulties of measuring high-temperature molten salt flow in reactor vessels. The flow sensor consists of a metallic cylindrical cavity coupled to a microwave waveguide. The cylindrical cavity has one of the flat surfaces thin enough to undergo microscopic deflection due to dynamic pressure of the exerted by the flowing fluid. Deflection of the membrane causes a shift in the microwave resonant frequency. Fluid velocity can be estimated from the calibration curve. The objective of this report is to investigate mechanical integrity of the flowmeter’s membrane. The membrane is a thin stainless-steel circular plate with a clamped edge, subjected to uniform load. By calculating the stress on the plate due to deflection and, comparing the stress to the material ultimate tensile strength and yield strength, it can be estimated if the plate will fail. If the maximum stress is greater than the yield strength, the plate will undergo plastic deformation, and the sensor will be disabled. A stress greater than the ultimate tensile strength will cause the plate to fracture. The stress on the plate was calculated with an analytic closed form solution model, and with COMSOL Structural Mechanics Module which does not involve any approximations. Stresses in both the analytic model and COMSOL numerical model were calculated for stainless steel 316 thin circular plates under room temperature conditions, where the fluid is water. The diameter of the circular plate is approximately one inch, and thickness is 10mil. Fluid flow velocity is in the range from 0.5m/s to 1m/s. The results from the two models are similar. Both the analytic model and COMSOL model showed that maximum stresses on the plate, which are at the radial boundary of the plate, are three orders of magnitude smaller than the yield strength and ultimate tensile strength. This indicates that the sensor is at a low risk of mechanical failure.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Stochastic Price Generation for Evaluating Wholesale Electricity Market Bidding Strategies

This work presents a novel method for generating electricity price scenarios from statistical properties of past electricity prices using a hybrid statistical and reduced-form stochastic model. Previous work in applying stochastic differential equations (SDE) to model electricity prices has focused on daily average prices. To extend stochastic price generation methods to hourly or sub-hourly pricing, we address several weaknesses in the state-of-the-art: (1) we replace the mean-reversion component of the SDE with an ARIMA process that is better able to characterize the daily and weekly trends; (2) we extend the price-spike, or jump process to account for conditional probabilities of price spikes occurring in consecutive time steps by replacing the traditional Poisson process for modeling jumps with a generalized point process model inspired by brain neuron models; and (3) we replace the traditional method of estimating spike intensity with empirical variance with a Markov process based on observed price spike intensity transitions. The method is demonstrated with electricity prices from the US ERCOT market and a use-case example is provided for bidding an energy storage unit into the day-ahead and real-time energy markets of ERCOT using stochastic optimization methods. Results show that the the synthetic price model out performs a (naive) persistence forecast model by resulting in 24% to 47% more in profits over 168 simulated days.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

HIGH-MASS STAR FORMATION TOWARD SOUTHERN INFRARED BUBBLE S10

An investigation in radio and infrared wavelengths of two high-mass star-forming regions toward the southern Galactic bubble S10 is presented here. The two regions under study are associated with the broken bubble S10 and Extended Green Object, G345.99-0.02, respectively. Radio continuum emission mapped at 610 and 1280 MHz using the Giant Metrewave Radio Telescope, India, is detected toward both of the regions. These regions are estimated to be ionized by early-B- to late-O-type stars. Spitzer GLIMPSE mid-infrared data is used to identify young stellar objects (YSOs) associated with these regions. A Class-I/II-type source, with an estimated mass of 6.2 M {sub ⊙}, lies ∼7″ from the radio peak. Pixel-wise, modified blackbody fits to the thermal dust emission using Herschel far-infrared data is performed to construct dust temperature and column density maps. Eight clumps are detected in the two regions using the 250 μ m image. The masses and linear diameter of these range between ∼300–1600 M {sub ⊙} and 0.2–1.1 pc, respectively, which qualifies them as high-mass star-forming clumps. Modeling of the spectral energy distribution of these clumps indicates the presence of high luminosity, high accretion rate, massive YSOs possibly in the accelerating accretion phase. Furthermore, based on the radio and MIR morphology, the occurrence of a possible bow wave toward the likely ionizing star is explored.

79 ASTRONOMY AND ASTROPHYSICS↗

Boxy/Peanut/X-Shaped Bulges: Steep Inner Rotation Curve Leads to Barlens Face-on Morphology

We use stellar dynamical bulge/disk/halo simulations to study whether barlenses (lens-like structures embedded in the narrow bar component) are only the face-on counterparts of Boxy/Peanut/X-shapes (B/P/X) seen in edge-on bars, or if some additional physical parameter affects that morphology. A range of bulge-to-disk mass and size ratios are explored: our nominal parameters (B/D=0.08, r{sub eff}/h{sub r}=0.07, disk comprising two-thirds of total force at 2.2h{sub r}) correspond to typical Milky Way mass galaxies. In all models, a bar with pronounced B/P/X forms in a few Gyr, visible in the edge-on view. However, the pure barlens morphology forms only in models with sufficiently steep inner rotation curves, dV{sub cir}/dr≳5V{sub max}/h{sub r}, achieved when including a small classical bulge with B/D≳0.02 and r{sub eff}/h{sub r}≲0.1. For shallower slopes, the central structure still resembles a barlens, but shows a clear X signature even in low inclinations. A similar result holds for bulge-less simulations, where the central slope is modified by changing the halo concentration. The predicted sensitivity on the inner rotation curve is consistent with the slopes that are estimated from gravitational potentials calculated from the 3.6 μm images, for the observed barlens and X-shaped galaxies in the Spitzer Survey of Stellar Structure in Galaxies (S{sup 4}G). For inclinations <60° the galaxies with barlenses have on average twice steeper inner rotation curves than galaxies with X shapes: the limiting slope is ∼250 km s{sup −1} kpc{sup −1}. Among barred galaxies, those with barlenses have both the strongest bars and the largest relative excess of inner surface density, both in barlens regions (≲0.5h{sub r}) and near the center (≲0.1h{sub r}); this provides evidence for bar-driven secular evolution in galaxies.

79 ASTRONOMY AND ASTROPHYSICS↗

Binary architecture of the Na v 1.2-β2 signaling complex

To investigate the mechanisms by which β-subunits influence Na v channel function, we solved the crystal structure of the β2 extracellular domain at 1.35Å. We combined these data with known bacterial Na v channel structural insights and novel functional studies to determine the interactions of specific residues in β2 with Na v 1.2. We identified a flexible loop formed by 72 Cys and 75 Cys, a unique feature among the four β-subunit isoforms. Moreover, we found that 55 Cys helps to determine the influence of β2 on Na v 1.2 toxin susceptibility. Further mutagenesis combined with the use of spider toxins reveals that 55 Cys forms a disulfide bond with 910 Cys in the Na v 1.2 domain II pore loop, thereby suggesting a 1:1 stoichiometry. Our results also provide clues as to which disulfide bonds are formed between adjacent Na v 1.2 912/918 Cys residues. The concepts emerging from this work will help to form a model reflecting the β-subunit location in a Na v channel complex.

59 BASIC BIOLOGICAL SCIENCES↗

The synthesis of starch from carbon dioxide using isolubilized stabilized enzymes

Systems for artificial manufacture of starch and for delineation of technological areas, and the rationale for studying them are considered. A discussion of the enzyme-catalyzed routes of synthesis available and a choice as to the most promising route are presented. A discussion of the enzymes involved, of enzyme insolubilization technology, and of possible engineering approaches, with examples in the form of model calculations for both reactors and separators, are also presented.

Bassham, J. A.↗

Models of subjective response to in-flight motion data

Mathematical relationships between subjective comfort and environmental variables in an air transportation system are investigated. As a first step in model building, only the motion variables are incorporated and sensitivities are obtained using stepwise multiple regression analysis. The data for these models have been collected from commercial passenger flights. Two models are considered. In the first, subjective comfort is assumed to depend on rms values of the six-degrees-of-freedom accelerations. The second assumes a Rustenburg type human response function in obtaining frequency weighted rms accelerations, which are used in a linear model. The form of the human response function is examined and the results yield a human response weighting function for different degrees of freedom.

Rudrapatna, A. N.↗

Model of human dynamic orientation

The dynamics associated with the perception of orientation were modelled for near-threshold and suprathreshold vestibular stimuli. A model of the information available at the peripheral sensors which was consistent with available neurophysiologic data was developed and served as the basis for the models of the perceptual responses. The central processor was assumed to utilize the information from the peripheral sensors in an optimal (minimum mean square error) manner to produce the perceptual estimates of dynamic orientation. This assumption, coupled with the models of sensory information, determined the form of the model for the central processor. The problem of integrating information from the semi-circular canals and the otoliths to predict the perceptual response to motions which stimulated both organs was studied. A model was developed which was shown to be useful in predicting the perceptual response to multi-sensory stimuli.

Ormsby, C. C.↗

An assembler for the MOS Technology 6502 microprocessor as implemented in jolt (TM) and KIM-1 (TM)

Design of low-cost, microcomputer-based navigation receivers, and the assembler are described. The development of computer software for microprocessors is materially aided by the assembler program using mnemonic variable names. The flexibility of the environment provided by the IBM's Virtual Machine Facility and the Conversational Monitor System, make possible the convenient assembler access. The implementation of the assembler for the microprocessor chip serves a part of the present need and forms a model for support of other microprocessors.

Lilley, R. W.↗

Development of a laminate fatigue analysis

A fatigue analysis technique developed to predict damage growth in notched laminates is described. Features of the analysis include: criteria to relate matrix failure to cyclic stresses in and between plies; correlation of delamination growth with strain-release rate; and in-plane shear modulus change is related to cyclic shear stresses. A simplified finite element model is used to determine stresses in laminates that contain matrix damage. Failure criteria are integrated with the finite element model to form the fatigue analysis.

Roderick, G. L.↗

Long-wave baroclinic instability in the troposphere and stratosphere with spherical geometry

The most unstable normal modes are obtained for a global, quasi-geostrophic and spectral-form atmospheric model that includes wavenumbers one through six. In a first set of model calculations, the basic state represents Northern Hemisphere winter solstice conditions, whose long waves are deep modes having maximum kinetic energy in the stratosphere. These internal modes exist even in the presence of a stratospheric wind minimum, but propagate vertically into the stratosphere only north of this minimum, at the latitudes of the polar jet. The basic state for a second set of calculations is the axisymmetric solution corresponding to radiative equilibrium, with large vertical wind shear and all modes being essentially external, tropospheric Charney modes.

Straus, D. M.↗

Application of HCMM data to regional geologic analysis for mineral and energy resource evaluation

The effects of topographic elevation and slope on thermal images were examined using representative field obstructions of the solar and sky radiation and a simple linearized thermal model. The forms are easily adapted for analysis of HCMM images using the DMA digital terrain data. From a representative set of field observations, it was found that flux variations with elevation can cause changes in the mean diurnal temperature gradient from -4 deg to -14 deg per km evaluated at 2000 m. Changes in the temperature difference gradient of 1 to 2 C per km are also produced which is equivalent to an effective thermal inertia gradient of 100 W s to the 1/2 power/sq m K/1 per km. Exposed bedrock on topographic ridges will appear to have a lower thermal inertia due to the additional effect.

Watson, K.↗

Aerodynamics on a transport aircraft type wing-body model

The DFLR-F4 wing-body combination is studied. The 1/38 model is formed by a 9.5 aspect ratio transonic wing and an Airbus A 310 fuselage. The F4 wing geometrical characteristics are described and the main experimental results obtained in the S2MA wind tunnel are discussed. Both wing-fuselage interferences and viscous effects, which are important on the wing due to a high rear loading, are investigated by performing 3D calculations. An attempt is made to find their limitations.

Schmitt, V.↗

Computational modeling of multispectral remote sensing systems: Background investigations

A computational model of the deterministic and stochastic process of remote sensing has been developed based upon the results of the investigations presented. The model is used in studying concepts for improving worldwide environment and resource monitoring. A review of various atmospheric radiative transfer models is presented as well as details of the selected model. Functional forms for spectral diffuse reflectance with variability introduced are also presented. A cloud detection algorithm and the stochastic nature of remote sensing data with its implications are considered.

Aherron, R. M.↗

Crop weather models of corn and soybeans for Agrophysical Units (APU's) in Iowa using monthly meteorological predictors

Models based on multiple regression were developed to estimate corn and soybean yield from weather data for agrophysical units (APU) in Iowa. The predictor variables are derived from monthly average temperature and monthly total precipitation data at meteorological stations in the cooperative network. The models are similar in form to the previous models developed for crop reporting districts (CRD). The trends and derived variables were the same and the approach to select the significant predictors was similar to that used in developing the CRD models. The APU's were selected to be more homogeneous with respect crop to production than the CRDs. The APU models are quite similar to the CRD models, similar explained variation and number of predictor variables. The APU models are to be independently evaluated and compared to the previously evaluated CRD models. That comparison should indicate the preferred model area for this application, i.e., APU or CRD.

Leduc, S.↗

Crop weather models of barley and spring wheat yield for agrophysical units in North Dakota

Models based on multiple regression were developed to estimate barley yield and spring wheat yield from weather data for Agrophysical units(APU) in North Dakota. The predictor variables are derived from monthly average temperature and monthly total precipitation data at meteorological stations in the cooperative network. The models are similar in form to the previous models developed for Crop Reporting Districts (CRD). The trends and derived variables were the same and the approach to select the significant predictors was similar to that used in developing the CRD models. The APU models show sight improvements in some of the statistics of the models, e.g., explained variation. These models are to be independently evaluated and compared to the previously evaluated CRD models. The comparison will indicate the preferred model area for this application, i.e., APU or CRD.

Leduc, S.↗