Search NASA⌕ Search

SEARCH · Search NASA

Results for “Texturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Quasi in-situ analysis of geometrically necessary dislocation density in α-fibre and γ-fibre during static recrystallization in cold-rolled low-carbon Ti-V bearing microalloyed steel

Highlights: • Average GND density is higher in gamma fibre than alpha fibre. • Higher drop in average GND density in un-recrystallized portion of gamma fibre • Fine precipitates pin the grain boundary at 700 °C 0 s. • Precipitates are coarse at 800 °C and present inside strain-free grains. - Abstract: In the present study, cold-rolled low-carbon steel is annealed at three different conditions: 700 °C for 0 s, 800 °C for 0 s and 800 °C for 2 min at the heating rate of ~10 °C/s. Recrystallization behaviour on sample surface is studied using a heated stage Scanning Electron Microscopy and Electron Backscattered Diffraction. For the lower annealing temperature of 700 °C with no dwell, almost no recrystallization is observed and microstructure resembles the as-received deformed material with the exception of occasional sub-micron sized nuclei. For the annealing conditions of 800 °C 0 s and 800 °C 2 min, onset and evolution of recrystallization is observed in-situ as a function of the initial as-cold rolled texture. Slower recovery rate of alpha fibre than gamma fibre is observed and confirmed by lower drop in average geometrically necessary dislocation (GND) density for un-recrystallized alpha fibres (1.1E+14 m{sup −2} for 700 °C 0 s, 1.4E+14 m{sup −2} for 800 °C 0 s and 4.5E+14 m{sup −2} for 800 °C 2 min) than for un-recrystallized gamma fibre grains (3.0E+14 m{sup −2} for 700 °C 0 s, 6.2E+14 m{sup −2} for 800 °C 0 s and 9.8E+14 m{sup −2} for 800 °C 2 min) during annealing. Strong gamma texture in recrystallized matrix is found for annealing conditions of 800 °C 0 s and 800 °C 2 min. From TEM characterisation it was shown that sub-grain boundaries are decorated with fine precipitates (diameter d < 15 nm) of titanium‑vanadium carbides (Ti,V)C for the annealing condition of 700 °C 0 s, which suggests that these precipitates play a major overall role in retardation of the recrystallization kinetics.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructural and micro-mechanical analysis of 14YWT nanostructured Ferritic alloy after varying thermo-mechanical processing paths into tubing

Microstructural analyses and micro-pillar compression were conducted on 14YWT nanostructured ferritic alloy (NFA) to compare different processing pathways: hydrostatic extrusion and Pilger processing with varying annealing temperatures into thin walled tubing, and after hot extrusion and cross-rolling into a plate. Hydrostatic extrusion at 815 °C resulted in the smallest grain sizes and highest yield strength of 1.20 GPa. Pilger processing with annealing at 800 °C had fine grained regions and bands of coarse grains, leading to a large variation in yield strength of 0.9–1.40 GPa. Higher annealing temperatures of 1200 °C after pilger processing significantly increased the grain size and lowered the yield strength to 1.01 GPa. These tubes showed a stronger (111) crystallographic texture in the normal direction and elongated grains in the extrusion direction. Characterization of the nano-oxides using TEM reveals more numerous, smaller oxides present in tubing processed at lower temperatures. Overall, this work shows NFA tubing after hydrostatic extrusion and pilger processing can lead to fine grained microstructures and texturing leading to higher yield strengths at lower annealing temperatures (e.g. 800 °C).

14YWT↗
DOE OSTI2021

Direct Observation of Tungsten Oxidation Studied by In Situ Environmental TEM

In this study, in situ environmental transmission electron microscopy (ETEM) was applied, for the first time, to investigate the thermal oxidation of a pristine and a self-ion irradiated polycrystalline tungsten, using a MEMS-based gas cell at 500 oC to 900 oC in a 1 bar 2%O2/N2 gas mixture. By tracking the dynamic evolution of the tungsten oxide scale as it initiates, grows, and sublimates during a consecutive thermal oxidation experiment, we observed two distinctive tungsten oxide microstructure – one nanocrystalline o-WO3 scale grown on W{27-1 } and W{1-1 8} and another o-WO3 scale exhibits a novel highly textured nanostructure. While the two oxide microstructures shared a similar thickness of ~200 nm after 40-minute early-stage oxidation, the nanocrystalline scale on the W{27-1 } grew much more rapidly at 800 oC than the highly textured oxide at a higher temperature of 900 oC. This suggests both the microstructure of these tungsten oxide scales as well as their oxidation kinetics are highly sensitive to the tungsten surface orientation, and such correlations also change dynamically in the course of oxidation. We also discuss the tungsten oxidation mechanism, the effects of the TEM foil thickness, and the focused ion beam (FIB) Ga+ damage on in situ ETEM oxidation.

In situ ETEM, Tungsten, Thermal oxidation, Orienta↗
DOE OSTI2017

Ferroelectric and dielectric study of strontium tantalum based perovskite oxynitride films deposited by reactive rf magnetron sputtering

Highlights: • Oxynitride perovskite thin films were deposited by reactive sputtering. • Films are textured or epitaxially grown on MgO and Nb-SrTiO{sub 3} substrates. • Local piezoelectric and ferroelectric behavior was highlighted by PFM. • A 1600 nm-thick film presents a permittivity of 175 at 10 kHz and RT. • Permittivity is around 65 in high frequency range. - Abstract: Strontium and tantalum based oxynitride perovskite thin films were deposited by reactive magnetron sputtering. Epitaxial films deposited on Nb-SrTiO{sub 3} substrates show smooth surfaces with roughness values from 1.5 to 3.6 nm for a thickness of films in the range 20–1600 nm. The samples are yellow with band gap values around 2.35 eV. Piezo-force microscopy characterization pointed out the local piezoelectric and ferroelectric behavior of the oxynitride perovskite films. In the low frequency range, the 1600 nm-thick film exhibits a permittivity of 175 at 10 kHz, with dielectric losses of 0.055. Permittivity is lowered in high frequencies with a value around 65 obtained on a 1520 nm-thick film deposited on MgO substrate, which is textured with a preferential c-axis orientation. No accordability of the permittivity was highlighted at a macroscopic scale. The moderate crystallographic strain evidenced in the 20 nm thin film does not induce a high permittivity.

36 MATERIALS SCIENCE↗
DOE OSTI2017

One-pot synthesis of Ni/Ni{sub 3}C/Ni{sub 3}N nanocomposite: Structure, growth mechanism and magnetic properties

Graphical abstract: Ni/Ni{sub 3}C/Ni{sub 3}N nanocomposites were synthesized by a one-pot solution chemistry method at lower temperature of 200 °C. The formation mechanism, magnetic properties and textural structures of Ni/Ni{sub 3}C/Ni{sub 3}N nanocomposite were investigated. - Highlights: • Ni/Ni{sub 3}C/Ni{sub 3}N nanocomposites were synthesized by a one-pot solution chemistry method at lower temperature of 200 °C. • Ni{sub 3}N nanomaterials were generally obtained by two steps, here we use one-step for preparation of Ni{sub 3}N nanomaterials. • The formation mechanism, magnetic properties and textural structures of Ni/Ni{sub 3}C/Ni{sub 3}N nanocomposite were investigated. - Abstract: A one-pot solvothermal synthesis of Ni/Ni{sub 3}C/Ni{sub 3}N nanocomposite, using hydrazine hydrate (N{sub 2}H{sub 4}) as reducing agent and tetraethylene glycol (TEG) as solvent, is reported. The contents of Ni{sub 3}C and Ni{sub 3}N decrease with increasing the amount of N{sub 2}H{sub 4}. The magnetic hysteresis loops at room temperature of the Ni/Ni{sub 3}C/Ni{sub 3}N display ferromagnetic characteristics. Saturation magnetization increases gradually with increasing Ni content of the Ni/Ni{sub 3}C/Ni{sub 3}N. Growth mechanism is discussed based on the characterization results of X-ray diffraction (XRD), scanning electron microscope (SEM), and X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TG), nitrogen adsorption desorption, and elemental analysis. Furthermore, Ni{sub 3}N was fabricated by such a solution chemistry method at low-temperature of 200 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Magnesium Alloy ZK60 Tubing made by Shear Assisted Processing and Extrusion (ShAPE)

ZK60 Magnesium tubing has been friction extruded from as-cast billets and T5 conditioned bars using Shear Assisted Processing and Extrusion (ShAPE). Tubes having an outer diameter of 50.8 mm and wall thickness of 1.9 mm were extruded with >20 times less ram force compared to conventional extrusion due to the unique shearing conditions and tooling inherent to ShAPE. Microstructures of the as-cast billet and T5 bar feedstock materials were significantly different from each other in terms of grain size, texture, and second phase distribution; yet the resulting microstructures after ShAPE were remarkably similar. An average grain size of 4-5 microns, 20o tilt of basal texture away from the extrusion axis, and refined second phases having a uniform distribution were achieved independent of the feedstock material. Hardness for as-extruded and artificially aged tubes are presented with isotropic behavior explained by detailed microstructural analysis. This work suggests that bulk ZK60 magnesium alloys extrusions may be fabricated in a single step, with microstructures that are unobtainable with conventional extrusion.

Friction Stir Extrusion, Friction Consolidation an↗
DOE OSTI2020

AA2024/SiC metal matrix composites simultaneously improve ductility and cracking resistance during elevated temperature deformation

Here this study uses the stir-casting technique to combine a semi-solid AA2024 alloy directly with finely-sized β-SiC p embedded as a powder or with mechanically alloyed granules as a delivery agent. Liquid-state primary fabrication tends to form agglomerates of reinforcement particles, whereas rolling better distributes the composite constituents. Sub-micron reinforcements of low volume fractions do not significantly increase the hardness of the composite materials. Uniaxial tensile testing at elevated temperatures over a wide range of strain rates showed simultaneous increases in the ductility and crack resistance of AA2024 + SiC p granules embedded as a powder when compared to the non-reinforced control material at lower strain rates, with the same toughness as the control material. The maximum engineering strain of 252.7 ± 19.2% was observed in AA2024/SiCp at a strain rate of 10 -4 s -1 . This improvement in properties is attributed to grain refinement in the MMCs, leading to pinning events during the straining and ductility increases. The resultant impediments to grain growth and crack propagation allow the fine-sized reinforcements to control dynamic microstructural changes during fatigue. Cube {001}<100> is a dominant texture component in AA2024, whereas the Goss {011}<100> and S {123}<634> components mainly represent the texture of the discontinuously reinforced aluminum matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Laser powder bed fusion of oxide dispersion-strengthened IN718 alloys: A complementary study on microstructure and mechanical properties

In this study, two new grades of oxide dispersion strengthened (ODS) Inconel 718 (IN718) alloys were designed by the thermochemical CALPHAD method and produced by laser powder bed fusion (LPBF) technique. Alloys designated as IN718-YF and IN718-YFH, that consist Y 2 O 3 –FeO and Y 2 O 3 –FeO–Hf, respectively, were fabricated with >99.9 % densification using optimized process parameters. CALPHAD calculations were highly consistent with experimental findings, highlighting the formation of Al-containing Y–Ti–O and Y–Hf–O nano-oxides in both alloy types. Texture analyzes revealed no significant texture development in as-built (AB) or heat-treated (HT) alloys. Heat treatment was applied at 1050 °C for 1 h to enhance nano-oxide density. Further, the nano-oxide number density remained similar in IN718-YF while it decreased in IN718-YFH alloy as a result of carbide formation after the heat treatment. Besides, formation of secondary γ' particles was observed in the IN718-YFH/HT alloy. Even though the yield strengths of IN718-YF and IN718-YFH alloys in both AB and HT conditions were similar, the ductility of IN718-YFH was ~50 % less in almost all conditions compared to the ductility of IN718-YF. This has been shown to be as a result of irregular shaped micron-sized Y-Hf-O oxides, martensite formation in AB condition, increased amount of carbides and existence of secondary γ' particles in HT condition in IN718-YFH. High density of stacking faults (SF) forming at the interface of the nano-oxides have been detected in IN718-YF alloys. Besides dislocation/nanoparticle interactions, SFs which are responsible for the delocalization of the deformation improve the ductility of IN718-YF alloys. Overall, high temperature mechanical tests exhibit that both alloys have higher strength with improved ductility compared to the standard IN718 alloys, indicating the contribution of the nano-oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Developing an experimental-computational framework to investigate the deformation mechanisms and mechanical properties of Al-8Ce-10Mg alloys at micro and macroscales

There is a promising future for the use of aluminum-cerium-magnesium alloys in a broad range of applications, including devices that operate at high temperatures. With cerium currently considered a waste product of rare earth mining validation studies of possible applications are essential to reduce the environmental waste. Here, a computational-experimental framework is developed to investigate the role both the intermetallic and matrix have on the mechanical properties of these alloys. A set of experiments, including SEM/EBSD imaging, nanoindentation, in-situ SEM tensile testing, and in-situ SEM-DIC tests are performed to characterize the microstructure and mechanical properties of these alloys. Furthermore, the elastic, plastic, and failure deformation mechanisms of the microstructure, and their correlation with the bulk scale mechanical properties are investigated. Experimental results are also used to calibrate parameters for a crystal plasticity finite element model, by performing a computational framework that minimizes the error between the computational and experimental results. This model is then utilized to investigate how the area percentage of intermetallics and the crystallographic texture control the mechanical properties of the alloy. Simulation results show that an increase in the percentage of intermetallics increase the strength but decrease the ductility of the alloy. Also, a change in material texture improves strength and reduces damage that leads to material failure. The development of the crystal plasticity model, as discussed in this work, opens opportunities for future investigations of similar aluminum-cerium-magnesium alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Evidence for metal sources, fluid-mixing processes, and S isotope recycling within the feeder zone of an Irish type Zn-Pb deposit

The origin and evolution of fluids in Irish-type Zn-Pb deposits remains debated, particularly regarding the mobility of metals such as Cu and Ni, sources of sulphur, and the role of fluid mixing and replacement. The Lisheen Zn-Pb deposit, Ireland, offers a well-defined natural laboratory to investigate these questions. While most studies have focused on the Waulsortian Limestone Formation, the primary sulphide host, less is known about mineralisation in underlying units, such as the Lisduff Oolite Member (LOM). The LOM displays enrichment in Cu and Ni and displays intense replacement textures compared to other hosts at Lisheen, making it an ideal target for studying metal mobility and sulphur recycling in carbonate-hosted systems. Through characterising and studying LOM-hosted sulphides, valuable insights into mineralisation processes, especially related to Cu-Ni metals, can be defined. This study integrates petrography, EMPA, and in situ sulphur isotope (δ 34 S) analysis to investigate sulphide paragenesis, mineral chemistry, and fluid evolution across LOM ore zones. Results reveal a multistage mineralising system involving extensive replacement of early pyrite (Py0, δ 34 S = −28.4 to −21.9 ‰) by sphalerite and galena, with zoned pyrite (Py1) enriched in As-Cu-Ni-Tl. The δ 34 S values and trace element trends indicate mixing between hydrothermal and bacteriogenic sulphur-rich fluids, with evidence for sulphur recycling during replacement. Pyrite textures and compositions capture this evolving fluid regime, with trace element enrichment linked to paragenetic stage. The steel ore region, adjacent to major fault intersections, records intense hydrothermal fluid interaction, hosting Ni- and As-rich phases such as nickeline, gersdorffite, and arsenopyrite. These findings highlight the importance of structural controls and fluid mixing in metal transport and deposition, positioning the LOM as a key stratigraphic unit for understanding ore-forming processes in Irish-type systems. These results have implications for targeting similar carbonate-hosted systems globally, especially where deeper or structurally complex ore zones remain underexplored.

58 - GEOSCIENCES↗
DOE OSTI2023

Electrodeposited nickel coatings for exceptional corrosion mitigation in industrial grade molten chloride salts for concentrating solar power

Molten chloride salt eutectics are attractive candidates for use as thermal energy storage media and heat transfer fluids in generation-three concentrating solar thermal power (Gen3 CSP) plants. However, corrosion of alloys in molten chloride salts, especially at high temperatures, is an extremely challenging problem that studies focus on lower temperatures, shorter durations, or analytical grade, and high-purity, salts. To date, there has been no study on corrosion or corrosion mitigation in an industrial-grade salt at a high temperature such as 750 °C. To alleviate this knowledge gap, the study presents new multiscale fractal-textured Ni coatings on various alloy surfaces for effective corrosion mitigation at 750 °C in molten chloride salts. Using the electrodeposition method, durable double-layer textured coatings were formed on stainless steel alloys (SS316, SS310, and SS347) and In800H. The corrosion performance of the coatings is investigated in both analytical-grade purity and, for the first time, practically relevant industrial-grade chloride salts. Ni-coated ferrous alloys showed an exceptionally reduced corrosion rate in the range of 350–480 μm/y in analytical-grade salts, and between 450 and 490 μm/y in purified industrial-grade salts at 750 °C. Ni coatings on ferrous alloys reduced corrosion rates by as much as 70% compared to uncoated surfaces and were comparable to the expensive Ha230 alloy with a high Ni content. As a result, by the use of innovative fractal corrosion mitigation coatings, for the first time, low-cost structural alloys are rendered viable for use with industrial-grade chloride salts, which is profoundly beneficial in practical systems.

14 SOLAR ENERGY↗
DOE OSTI2024

Biomolecular budget of persistent, microbial-derived soil organic carbon: The importance of underexplored pools

The details of how soil microorganisms contribute to stable soil organic carbon pools are a pressing knowledge gap with direct implications for soil health and climate mitigation. It is now recognized that microbial necromass contributes substantially to the formation of stable soil carbon. However, the quantification of necromass in soils has largely been limited to model molecules such as aminosugar biomarkers. The abundance and chemical composition of other persistent microbial residues remain unresolved, particularly concerning how these pools may vary with microbial community structure, soil texture, and management practices. We use yearlong soil incubation experiments with an isotopic tracer to quantify the composition of persistent residues derived from microbial communities inhabiting sand or silt dominated soil with annual (corn) or perennial (switchgrass) monocultures. Persistent microbial residues were recovered in diverse soil biomolecular pools including metabolites, proteins, lipids, and mineral-associated organic matter (MAOM). The relative abundances of microbial contributions to necromass pools were consistent across cropping systems and soil textures. The greatest residue accumulation was not recovered in MAOM but in the light density fraction of soil debris that persisted after extraction by chemical fractionation using organic solvents. Necromass abundance was positively correlated with microbial biomass abundance and revealed a possible role of cell wall morphology in enhancing microbial carbon persistence; while gram-negative bacteria accounted for the greatest contribution to microbial-derived carbon by mass at one year, residues from gram-positive Actinobacteria and Firmicutes showed greater durability. Together these results offer a quantitative assessment of the relative importance of diverse molecular classes for generating durable soil carbon.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Tailoring the nanotwin spacing of Ni-Mo-W alloys via composition and substrate temperature control

Alloy chemistry and deposition conditions can strongly influence the structure and properties of nanostructured materials. However, in Ni-Mo-W alloys, the limited influence of deposition rate on the twin spacing compels the exploration of other routes to tailor the structure and properties. This study was undertaken to investigate the effect of composition and substrate temperature on the nanotwin spacing of sputter-deposited Ni-Mo-W alloys. Increasing the Ni content from 84 at.% to 93 at.% doubled the average twin spacing from 1.8 nm to 3.8 nm, while raising the substrate temperature from room temperature to 200°C for a fixed Ni content of 91 at.% resulted in an increase from 2.9 nm to 5.0 nm. Concurrent weakening of the {111} texture occurred with both increased Ni and temperature. Furthermore, the combined effectiveness of composition and temperature demonstrated here provides a potential process window for tuning the twin spacing while maintaining the strongly textured columnar structure.

36 MATERIALS SCIENCE↗
DOE OSTI2020

PERC silicon PV infrared to ultraviolet optical model

Here, optical modeling of aluminum back surface field (Al-BSF) and passivated emitter and rear contact (PERC) silicon wafer solar cells are extended into the infrared wavelength range (300–2500 nm). The model incorporates ray tracing to account for pyramidal texture of the front silicon surface, free carrier absorption in the front emitter; bulk silicon wafer, BSF; and Lambertian scattering at the silicon back contact. Total reflectance of pyramidal textured cells with different contact geometries with and without encapsulation are simulated. Simulated reflectance and short circuit current density match well with experimental values. These physics-based optical models serve as input for evaluating optical and thermal management strategies for silicon wafer solar cells.

14 SOLAR ENERGY↗
DOE OSTI2021

Why does a phosphonium-phosphinate ionic liquid protect the contact surfaces from wear and micropitting but increase vibration when used as an additive in rolling-sliding lubrication?

A phosphonium-phosphinate ionic liquid (IL) was studied as a lubricant additive for rolling-sliding contacts. The bench-scale test was designed to simulate automotive rear axle operation during cold start, highway towing, and overload conditions. Adding such an IL (2%) into a base oil significantly reduced wear loss and rolling contact fatigue, e.g., microcracking and micropitting, but made the vibrational noise notably higher under a low (-1.5%) sliding roll ratio (SRR). Additionally, worn surface characterization revealed an interesting texture pattern with alternating smoother plateaus and rougher valleys, which is believed to cause the high vibration. No increased vibration was observed at a high (-30%) SRR, possibly because the more aggressive sliding abrasion prevented such a surface texture from forming.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Stress localization investigation of additively manufactured GRCop-42 thin-wall structure

A full-field crystal plasticity (CP) framework is presented for the GRCop-42 alloy to study microscopic mechanical behavior and local stress heterogeneities. The microstructures of additively manufactured (AM) materials are often unique relative to conventionally processed materials, and the local thermal histories drive these differences during the build process. These thermal histories depend on the process parameters (laser power, scan speed, and scan strategy) and the part geometry. Prior research has shown that the mechanical properties of thin-walled structures can vary significantly with wall thickness due to changes in the thermal boundary conditions during manufacturing. It is, therefore, desirable to perform CP simulations based on the phenomenological constitutive model to predict the local mechanical responses induced by microstructural heterogeneities. This work generates representative microstructures based on experimentally collected grain information (i.e., texture) for grain scale stress analysis, and the material constitutive parameters are calibrated using the experimental mechanical testing data. Here, we specifically investigated the effect of crystallographic texture and grain morphologies on the size-dependent mechanical properties of AM GRCop-42. The selection of appropriate material properties for implementing an effective free surface boundary condition and the influence of adjacent buffer layers are also discussed. Analysis of local field results reveals a strong correlation between stress localization and the initial grain orientation. However, no significant relationship between the misorientation of the individual adjacent grains and the average misorientation is observed.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Magnetic domain wall contrast under zero domain contrast conditions in spin polarized low energy electron microscopy

Critical applications of spin polarized low energy electron microscopy (SPLEEM) employ this technique's vector imaging capability to resolve domain wall (DW) spin textures. Studying several thin film systems including Co/W(110), Co/Cu(001) and (Co/Ni) n /W(110), we demonstrate that an additional contrast can appear at magnetic DWs. By imaging the magnetization as a function of electron landing energy, electron energies are selected at which the magnetic domain contrast vanishes. Surprisingly, under such conditions of zero contrast between magnetic domains, we observe the appearance of magnetic contrast outlining the DWs. This DW contrast fails to depend on the DW spin texture. Instead, our measurements show that this DW contrast results from a combination of the energy-dependence of the spin reflectivity asymmetry of the magnetic film, the finite energy width of the spin polarized electron source, and the dispersion of the magnetic prism array that separates the illumination and imaging columns of the instrument. Awareness of this DW contrast mechanism is useful to aid correct interpretation of SPLEEM images.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2025

Accumulation of Soil Microbial Necromass Controlled by Microbe–Mineral Interactions

Soil organic matter (SOM) is a key reservoir for global carbon (C), supporting soil fertility and influencing greenhouse gas emissions. Microbial residues, composed of dead cells and cellular fragments, are major contributors to SOM formation. Yet, mechanisms by which minerals enhance the accumulation of microbial residues remain poorly understood. Here, we used 13 C-labeled glucose in a year-long incubation to trace microbial residue in sandy and silty soils. Across both soils, approximately 89% of retained microbial 13 C was recovered in the fine (<53 μm) mineral-associated organic matter (MAOM) pool. Within this pool, the light MAOM fraction, enriched in poorly crystalline Fe minerals, held 4.3 times more 13 C than the heavy, phyllosilicate-dominated MAOM fraction, despite accounting for only 17.2% of the total MAOM mass and 12.3% of the total soil mass. Along with 13 C enrichment, the light MAOM fraction showed greater abundance of N-containing groups, e.g., (amides and amino groups), indicative of microbial-derived compounds like proteins and amino sugars. Fe oxides in light MAOM from both soils were spatially dispersed. Microbial residue accumulation was greater in finer-textured silty soil. These findings demonstrate that mineral composition and texture jointly regulate microbial necromass accrual, highlighting light MAOM as a key pool for enhancing soil C storage.

13C isotope labeling↗