Search NASA⌕ Search

SEARCH · Search NASA

Results for “WELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Investigation of Hydrogen Embrittlement Susceptibility of X80 Weld Joints by Thermal Simulation

The objective of this study was to investigate the hydrogen embrittlement (HE) susceptibility and influence mechanism of X80 weld joints. Slow strain rate testing (SSRT) under in situ H-charging, combined with microstructure and fracture analysis, was performed on the base metal (BM), weld metal (WM), thermally simulated fine-grained heat-affected zone (FGHAZ) and coarse-grained heat-affected zone (CGHAZ). Results showed that the WM and simulated HAZ had a greater degree of high local strain distribution than the BM; compared to the CGHAZ, the FGHAZ had lower microhardness and more uniformly distributed stress. SSRT results showed that the weld joint was highly sensitive to HE; the HE index decreased in the following sequence: FGHAZ, WM, CGHAZ and BM. The effect of the microstructure on HE was mainly reflected in microstructure, local stress distribution and microhardness.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Heat Exposure on the Fatigue Properties of AA7050 Friction Stir Welds

This work examines the effect of heat exposure on the subsequent monotonic and fatigue properties of friction stir-welded AA7050. Mechanical characterization tests were conducted on friction stir-welded specimens as-welded (AW) and specimens heated to 315 °C in air for 20 min. Monotonic testing revealed high joint efficiencies of 98% (UTS) in the AW specimens and 60% in the heat-damaged (HD) specimens. Experimental results of strain-controlled fatigue testing revealed shorter fatigue lives for the HD coupons by nearly a factor of four, except for the highest strain amplitude tested. Postmortem fractography analysis found similar crack initiation or propagation behavior between the AW and HD specimens; however, the failure locations for the AW were predominantly in the heat-affected zone, while the HD specimens also failed in the stir zone. Microhardness measurements revealed a relatively uniform strength profile in the HD group, accounting for the variety of failure locations observed. The differences in both monotonic and cyclic properties observed between the AW and HD specimens support the conclusion that the heat damage (315 °C at 20 min) acts as an over-aging and a quasi-annealing treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Rotation Speed on the Microstructure and Mechanical Properties of Friction-Stir-Welded CuSn6 Tin Bronze

Four-mm-thick CuSn6 tin bronze plates were friction stir welded at a constant tool traverse speed of 100 mm min{sup −1}. Favorable joints could be obtained with rotation speeds ranging from 600 to 1000 rev min{sup −1}, and groove was found on the surface of the joint under 400 rev min{sup −1}. The microstructure of the weld nugget zone was characterized by equiaxed recrystallized grains with heterogeneity along the thickness direction. Moreover, the grain size of the thermo-mechanically affected zone and stir zone increased with the increase in rotation speed. Hardness of the stir zone was higher than that of other zones due to microstructural refinement. There was little change in tensile properties of the defect-free welded joints. During tensile test, all of the defect-free joints were fractured at heat-affected zone with typical plastic fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Boron Content on Hot Ductility and Hot Cracking Susceptibility in 316L Austenitic Stainless Steel for Welding Components

Liquation cracking may occur in the heat-affected zone during welding. Two factors influence this phenomenon: the tensile stresses generated during welding and the potential loss of ductility due to the presence of a liquid film at grain boundaries depending on their chemical composition. Gleeble hot ductility tests have been used to study the combined effect of boron content and holding time on ductility drop in the liquation temperature range of a 316L type austenitic stainless steel. It is shown that high boron contents and short holding times promote the loss of ductility in this temperature range. Secondary ion mass spectrometry has been used to correlate mechanical results to boron distribution either at grain boundaries or in the bulk. Other welding tests have been performed to confirm the influence of boron content on hot cracking sensitivity of AISI 316L stainless steels. Results indicate that cracks appear on all specimens but at different strain levels. The higher the boron content is, the more the specimen exhibits tendency to hot cracking.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Optimization of Tensile and Corrosion Properties of Dissimilar Friction Stir Welded AA2024-7075 Joints

In this work, we performed some joining experiments of dissimilar aluminum alloys AA2024-T351 and AA7075-T651 using friction stir welding (FSW) technique with different process parameters (rotational speed, welding speed and plunge depth). Response surface methodology based on a central composite rotatable design was used to establish the mathematical models predicting the tensile properties and corrosion rate of dissimilar FSW joints with some high confidence level. Analysis of variance method was employed to verify the developed models. Besides, the influences of FSW process parameters on tensile and corrosion properties of joints were analyzed. In order to obtain a desirable combination property of the dissimilar FSW joints, the optimum process parameters after experimental verification were proposed as: rotational speed 1495 rev/min, welding speed 187 mm/min and plunge depth 0.03 mm. This verification illustrated that the developed models are appropriate for the modeling and optimization of process.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Nonuniformity in Mechanical Properties of Linear Friction Welded Mild Steel Joint

Mild steel was successfully joined by linear friction welding. Grain size at peripheral region was coarser than that at the other zones of the weld interface, which had no significant effect on microhardness. The local tensile properties were considerably decreased when oxides or lack of bonding appeared at the interface. Ductile fracture dominated the fracture mode for all joints. Variation in local tensile properties could be relieved under a medium friction pressure, a relatively high amplitude with a sufficient friction time. It was attributed to the facts that plastic metal layer of joint became uniform to some extent and interfacial defects were eliminated. The standard deviation of plastic metal layer thickness (χ{sub p}) could be used to describe the combined effects of welding parameters on joint integral performance. It was found that the standard deviation of plastic metal layer thickness showed a strong inverse correlation with the joint integral performance. Well-formed and defect-free joints exhibiting 90% of the base metal tensile strength could be produced when processing at a frequency of 20 Hz with a friction pressure of 103 MPa or 155 MPa, an amplitude of 2.5 mm and a friction time of at least 4 s.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Hardening, Softening, and Mechanical Properties in Ultra-High-Strength DP1180 Tailor-Welded Blanks

In this paper, the microstructure, microhardness, tensile behavior, and formability of ultra-high-strength DP1180 tailor-welded blanks have been proposed to exhibit the micro- and macro-features of the hardening and softening phenomena. The microstructural investigation pointed to the effects of the microscale on the hardening mechanisms, such as martensite coarsening and martensite–austenite deficiency. Finally, the microstructural difference led to the increase in hardness, a reduction in cupping height, and also the fracture mode transformation in formability test of dissimilar DP1180–DP590 tailor-welded blanks. Furthermore, the softening mechanism in similar welded structures was also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Improvement of Al/Steel Tungsten Inert Gas Welding–Brazing Joint by High-Energy Shot Peening

High-energy shot peening treatment was applied to improve the Al/steel tungsten inert gas welding–brazing lap joint. The mechanical properties and microstructure evolution of the joint were investigated. Results showed that the mechanical properties of weld were evidently reinforced due to microstructure transformation of joint surface layer. The grain structure in the joint surface layer was distorted and refined. Large compressive residual stress was introduced into the joint surface, and its hardness obviously increased due to strain hardening. When the peening pressure was 0.15 MPa, the tensile shear strength of the joint reached the maximum value (199.6 MPa), which was 16.5% higher than that of the as-welded joint.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Forced Cooling Friction Stir Welding of 2060-T8 Al-Li Alloy

Friction stir welding of 2060-T8 Al-Li alloy was experimentally investigated. Forced cooling process was realized by placing two copper pressure plates with a waterway on both sides of weld top surface. The relations between joint formation, microstructures and mechanical properties were mainly discussed. Compared with conventional joint by natural cooling, the welding joint with smaller flashes by forced cooling has the smaller well-distributed grains and higher microhardness in the stir zone (SZ). The tensile strength and elongation of forced cooling joint, respectively, reach 445.7 MPa and 6.7%, which are obviously higher than those of the conventional joint. The fracture locations of the conventional and forced cooling joints are located in the SZ, and the fracture surface morphologies show a typical ductile fracture mode.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Characterization of Laser-Welded Ti Alloy and Stainless Steel Joint Using Cu Interlayer

In this study, Cu was used as an interlayer to restrain the formation of brittle Ti-Fe intermetallics when joining Ti alloy to SS. Microstructures of the joint were analyzed using optical microscopy, scanning electron microscopy and x-ray diffraction. Besides, the tensile strength of the joint was also measured. The melting amount of base materials was controlled by changing thickness of Cu interlayer to control the melting proportion in weld. The melting amount of base materials in weld decreased with the thickness of Cu interlayer. The content of Cu solid solution in weld increased with the thickness of Cu interlayer. Ti-Cu compound layer was formed on the Ti alloy side. The width of the Ti-Cu compound layer increased with the increase in heat input. The tensile strength of joint was largely impacted by Ti-Cu compound layer. The tensile strength of joint first increased and then decreased with the increase in width of the Ti-Cu compound layer.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Flow Patterns, Microstructure and Mechanical Properties of AZ31/Al6061 Dissimilar Friction Stir-Welded Joints

Dissimilar joints between die-cast AZ31 and extruded Al6061-T6 were joined using friction stir welding technology at a constant transverse speed (50 mm/min) and rotation rate of 800 or 1000 rpm. The flow patterns, microstructure evolution and intermetallic compounds in dissimilar joints were studied by optical and scanning electron microscopy. The relationship between microstructure and tensile properties was analyzed. The microhardness distribution along the horizontal centerline in cross section was investigated. Local flow without obvious mixing existed between Mg and Al metals in the tool shoulder-affected zone. For the tool-pin-affected zone, two typical zones, namely, the “extrusion zone” and “flow zone” existed because of the different flow modes of the plastic metals. The phase analysis showed that intermetallic compounds, including Al{sub 12}Mg{sub 17} and Al{sub 3}Mg{sub 2} formed in banded structures. Phase analysis showed that a joint with welding parameters of 800 rpm and 50 mm/min (Joint-500) had good mechanical properties because of the more uniform microstructure distribution and fewer intermetallic compounds. Fracture analysis indicated some microvoids and lamellate intermetallic compounds in the fracture surface of the joint with welding parameters of 1000 rpm and 50 mm/min (Joint-1000), which deteriorated its tensile strength significantly.

36 MATERIALS SCIENCE↗
DOE OSTI2019

The Effect of Annealing on the Properties of AW5754 Aluminum Alloy-AZ31B Magnesium Alloy Explosively Welded Bimetals

Explosive welding of AW5754 aluminum alloy to AZ31B magnesium alloy was performed. AW5754 was proposed as a flyer plate. A parallel setup was used during explosive welding. The annealing of AW5754/AZ31B composite plate at 250, 300 and 350 °C for 2, 3, 4 and 5 h was performed after explosive welding. Bimetals were characterized by regular wavy interface. Annealing resulted in the creation of intermetallic compounds (IMCs). The increase in the thickness of IMC interfacial layer was observed with increasing of annealing temperature and time. IMC layer of highest thickness was recorded after annealing at 350 °C for 5 h and averaged 67 µm. EDS analysis showed that the interfacial layer close to AW5754 alloy was formed by Al{sub 3}Mg{sub 2} IMC, and interfacial layer adjacent to the AZ31B alloy consisted of Mg{sub 17}Al{sub 12} IMC. Bright particles were spread at the AW5754-Al{sub 3}Mg{sub 2} IMC interface. Rise in the microhardness at the interface of produced bimetal was associated with work hardening. Microhardness values increased to 218 HV0.025 after annealing process due to IMCs present at the interface. Decrease in microhardness in locations close to the IMC interfacial layer was found after heat treatment due to recrystallization. The bimetal tensile strength reached 120 MPa. The annealing resulted in decrease in the bimetal tensile strength.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructural Development and Mechanical Properties of Friction Stir Welded Ferritic Stainless Steel AISI 409

This work investigates the effect of friction stir welding process parameters (rotation rate and traverse speed) on the microstructural evolution of friction stir welded (FSWed) ferritic stainless steel (FSS) AISI 409. Optical microscope, scanning electron microscope and electron backscattering diffraction are used to quantitatively assess the development in grain structure and texture. The microstructural development suggested that thermo-mechanical deformation occurs in the stir zone within the austenite/ferrite phase region, ultimately transforming upon cooling into bainitic/ferritic microstructure. The fraction and size of the bainitic/ferritic grains are found to vary through the thickness of the joints. High fractions of coarse ferritic grains are found near the top of the stir zone, and low fraction of fine ferritic grains is found near the bottom of the stir zone. This bainitic/ferritic grain structure resulted in an increase in the hardness of the stir zone by about 74% relative to the base material. The tensile strength of the FSWed FSS joints is almost at the same level of the base material with reduction in the ductility as a result of the increased hardness of the weld zone.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Impact of Backing Plate and Thermal Boundary Conditions for High-Speed Friction Stir Welding of 25-mm Thick Aluminum Alloy 7175-T79

Here this study demonstrates high-speed (150 mm/min) single pass friction stir butt joining of 25 mm thick aluminum alloy 7175-T79. To understand the impact of quenching and cooling rate on process responses, joint strength, and grain size distributions across the weld thickness, we performed a series of friction stir welding (FSW) trials in air and with a trailing water spray using steel and composite backing plates (BP). Welds made in air and trailing water spray exhibit significantly different hardness distributions across the nugget, heat affected zone (HAZ), and HAZ minimum hardness as evidenced by detailed microhardness mapping. The effect of trailing water spray (TWS) on joint efficiency overshadows the influence of BP composition due to the vastly different contribution to quenching. TWS also resulted in a multifaceted effect on FSW such as lowering processing temperature, increasing X and Z forces while lowering Y force, and narrow heat affecting zone. Finally, digital image correlation (DIC)-based fracture mode analysis and grain size measurements correlate with the hardness distribution.

42 ENGINEERING↗
DOE OSTI2020

Pitting behavior of friction stir repair-welded 304L stainless steel in 3.5% NaCl solution at room temperature: role of grain and defect structures

Stainless steel (SS) canisters used for storing spent nuclear waste are prone to chloride-induced stress corrosion cracking. Friction stir welding (FSW), being a low heat input process, can be used for repair welding of these canisters. In this study, an artificial crack was introduced on the 304L SS coupons by an electric discharge machining process. The artificial crack was repair-welded by FSW by maintaining the tool temperature a constant at two levels (725 and 825 °C). Friction stirring significantly reduced the grain size of the stirred zone (SZ) from about 47 to 2–4 μm. The fraction of low-angle grain boundaries increased in the SZ from 2 to 37–43%. Here, on the other hand, the fraction of special grain boundaries (Σ3 and Σ9) that was ~ 50% in the base metal reduced to < 10% in the SZ. During friction stirring, the oxide layer of artificial crack was broken and aligned to form a spiral defect called lazy-S structure. All these microstructural changes affected the corrosion behavior of the FSW specimens when tested in 3.5% NaCl at room temperature using cyclic polarization, chronoamperometry, and electrochemical impedance spectroscopy. The FSW specimens showed lower polarization resistance and lower transpassive potential than those of the base metal specimens. However, the pitting protection potentials of the FSW specimens were higher than that of the base metal. The pitting behavior of the FSW specimens was influenced more by the preferential attack on the lazy-S region than by passive film breakdown. The flat band potentials of the passive film formed on the FSW specimens were more positive than that of base metal. The charge carrier density of passive film formed on the FSW specimens was higher than that of the base metal. The higher fraction of low-angle grain boundaries present in the FSW specimens could supply more number of misorientation dislocations at the metal/film interface which could form anion vacancies by a climb process leading to formation of oxide at these locations without stressing the substrate. Therefore, low-angle boundaries are considered helpful for formation of stress-free passive films that will be highly stable and enhance both pitting and stress corrosion cracking resistance.

Dry storage canister↗
DOE OSTI2018

Residual stresses distribution, correlated with bending tests, within explosively welded Ti gr. 2/A1050 bimetals

Highlights: • Ti gr.2/A1050 clad was slightly affected by the explosive welding since negative sign values of stress tensor were detected. • Upon bending higher negative compression stresses were detected in this area. • Twins morphology changed from parallel to cross-shaped arrangement as a consequence of bending. • The compressive twinning was the dominant system before and after three point bending. - Abstract: Synchrotron radiation and XRD{sup 2} method were used to investigate the residual stress distribution before and after three point bending tests within an explosively welded composite composed of two light metals, namely: Ti gr. 2 and A1050. The analysis has shown that the bimetal is slightly affected by the explosive welding process since negative sign values of stress tensor were detected only in the immediate vicinity of interface of Ti gr. 2 characterized by a width of about 0.25 mm. Upon bending higher negative compression stresses are detected in this area as the σ{sub 11} value changes from −500 MPa to −1200 MPa. Additionally, the analysis of microstructure has revealed significant changes in twins morphology with primary and conjugate twinning before and after bending, respectively. However, the compressive twinning was the dominant system in both cases. Bending has changed the initial bimodal texture developing more spread basal components towards the transverse direction. The sample surface has been also significantly affected as the presence of compressive residual stress (−500 MPa) after bending was measured.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Deep reinforcement learning for optimal control of induction welding process

Optimizing induction welding (IW) process parameters for the application of joining thermoplastic composites is challenging as it requires achieving complex spatiotemporal thermal characteristics along the weld-line to obtain desired weld quality. We formulate an optimal control problem which captures these requirements and seeks to optimize the IW coil speed using a fast-acting dynamic IW process model. We develop a novel Deep Reinforcement Learning (DRL) framework to solve this computationally challenging control problem and demonstrate via simulation study that the learned DRL feedback control policy results in better spatiotemporal thermal characteristics as compared to the current state-of-the-art.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Self-welding of Inconel 617 under high-pressure-high-temperature conditions for nuclear reactors

In response to continuously declining availability of fossil fuels, nuclear power has become an important alternative source of power generation. Growing application of nuclear power has relieved the shortage of electricity. However, it is also accompanied with new drawbacks, such as radioactive waste, and potential catastrophic consequences in case of major accidents. For nuclear power plants, severe accidents mostly originate from the reactor, making the reliability of the reactor of paramount importance to the overall safety of a nuclear power plant. Massive heat generation through nuclear fission/fusion and heat exchange render the whole reactor operating at extremely high temperatures (i.e., 900–1000 °C), which, in conjunction with large load from subsystems/ components made of special heavy alloys, renders the reactor under the risk of self-welding, a phenomenon that could lead to strong bonding between components and paralyze the operability of the nuclear reactor. This paper investigates the self-welding behavior of Inconel 617, a primary candidate nickel alloy for key components of the next generation gas cooled nuclear plant, inside a controlled atmospheric furnace with preset static load, simulating the high-pressure high-temperature conditions inside nuclear reactors. Therefore, test results show that Inconel 617 experiences self-welding through common oxide zone at the interface, and it has remarkable bonding strength, requiring 4114 N (57.15 MPa) and 4338 N (60.25 MPa) to break apart a mated sample pair, under an apparent contact pressure of 0.341 MPa after 50-h aging, in helium and air atmospheres, respectively. The higher oxygen presence in air results in slightly stronger oxide bond at the interface, compared to helium, and the bond strength increases with dwell time.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗