Search NASA⌕ Search

SEARCH · Search NASA

Results for “catalyst loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

The Impact of Catalyst Layer Composition and Structure on Performance and Durability of PEMWE Anodes

A study of various compositions of anodes for proton exchange membrane water electrolysis aimed at reducing precious metal content and system costs without compromising performance and durability is presented. A key challenge in current water electrolysis technologies is the reliance on high iridium loadings to ensure sufficient catalytic activity, electronic conductivity, and durability for the oxygen evolution reaction. To address this, catalyst layers based on the stable but kinetically limited rutile phase of iridium oxide are combined with platinum nanoparticles and carbon-based additives to improve structural properties and ink processability. By systematically varying the volume ratios of carbon to precious metals and ionomer to solids, compositional trends have been identified, and significant performance improvements have been achieved. Structural and elemental analysis confirms improved dispersion of platinum and iridium can be achieved, as well as electronic conductivity improvements within the catalyst layer. Polarization curve analysis has shown the ability of added Pt and C to significantly increase catalytic activity. These results highlight the potential positive impact of Pt and C on anode structure, composition, and cell performance.

36 MATERIALS SCIENCE↗

Co-Design of Charge Transport Superhighways to Connect Catalytic Sites in Soft Photoelectrochemical Systems

Efficient photon-to-electron-to-molecule conversion requires multi-length scale control over charge transport pathways, where electronic charges are delivered to catalytic sites under high mass transport flux. A fundamental question is how can we co-design charge transport pathways to promote efficient charge transfer to/from catalytic sites in complex three-dimensional architectures? Soft conducting polymer systems offer exceptional promise to provide three-dimensional charge transport networks, where electrolyte (ion and solvent) can interdiffuse to promote long-lived charge carriers and the molecular nature allows for strategic synthetic design of catalytic sites. Herein we combine theoretical and experimental approaches to investigate the earliest stages of photoelectrochemical deposition of near-surface catalytic sites (Pt) on soft bulk heterojunction polymeric semiconductors composed of a prototype donor (PTB7-Th) and a prototype acceptor (N2200) as a model system towards better understanding molecular catalyst-polymer site interactions. We focus initially on photoelectrochemical deposition of low Pt loadings, nanoparticle sizes (formed by progressive nucleation) below 20 nm, for both density functional theory (DFT) modeling studies and for spectroscopic characterization using surface-sensitive X-ray and UV-photoemission (XPS/UPS). DFT modeling of “n-type” N2200 slabs reveal for the first time that sulfur atoms in the thiophene units serve as the lowest-energy adsorption sites for single Pt atoms, while larger Pt clusters engage more complexly with both thiophene and naphthalene diimide (NDI) core sites. Changes in chemical composition observed by X-ray photoelectron spectroscopy (XPS) support the DFT predictions, and the angle-resolved measurements reveal that Pt nucleation initiates at subsurface sites which appear to be localized active domains that promote charge transport/transfer and enable vertical growth toward the surface. These results suggest that light-activated Pt nanoparticle deposition decorates energetically distinct sites, where photoactivity is dictated by the local energetics of those sites, and the fact that they represent the termini of charge transport “super-highways” – a small percentage of the total volume of the donor/acceptor polymeric active layer which carries most of the photocurrent generated during both Pt deposition and photoelectrochemical HER. We posit that these initial studies provide a foundational strategy for design of catalytic sites in the near surface regions of complex polymeric materials and advancing soft semiconductor-based photoelectrochemical systems. Achieving a nanometer-scale understanding of catalyst deposition and the impact of local composition and energetics on that placement, should ultimately provide the design guidelines (co-design) for a broad array of catalysts at sites that optimize that efficiency and maximize platform durability.

14 SOLAR ENERGY↗

Mercury oxidation in flue gas using gold and palladium catalysts on fabric filters

The feasibility of oxidizing elemental mercury in coal combustion flue gas using catalytic material impregnated onto fabric filters was explored. TiO{sub 2}, Au/TiO{sub 2}, and Pd/Al{sub 2}O{sub 3} were studied based on promising results in previous research. Several fabric coating methods were investigated to determine the best way to load a filter. A spray coat method was found to have the highest initial loading and had the lowest losses after simulated pulse-jet cleaning. The oxidation performance of the catalyst-coated filters was tested using a simulated flue gas in a bench-scale reactor under conditions similar to those found in a baghouse. Au/TiO{sub 2} and Pd/Al{sub 2}O{sub 3} were effective, yielding mercury oxidation ranges of 40-60% and 50-80%, respectively. A 19 kW research combustor equipped with a baghouse was used to fire a range of coals and further test the performance of Pd/Al{sub 2}O{sub 3}. Results obtained warrant further development of this technique as a means of mercury pollution control. 19 refs., 2 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Selective and Stable Non-Noble-Metal Intermetallic Compound Catalyst for the Direct Dehydrogenation of Propane to Propylene

A non-noble intermetallic compound catalyst consisting of Ni 3 Ga nanoparticles supported on Al 2 O 3 that exhibits high selectivity (~94%), comparable activity (TOF = 4.7 × 10 –2 s –1 ), good stability (~94% to 81% over the 82 h test), and regenerability in the direct dehydrogenation of propane to propylene at 600 °C has been developed. Through synthesis techniques that stabilize the Ni 3 Ga phase, the surface composition of the catalytic nanoparticles could be tuned by Ni and Ga loading such that improved selectivity toward propylene may be achieved. Comparisons with well-defined silica-supported Ni 3 Ga and NiGa catalysts and Ni 3 Ga/Al 2 O 3 with a range of Ni:Ga loading suggested that a specific surface composition range was most promising for propylene production. Furthermore the presence of Ni at the active particle surface was also found to be critical to drive dehydrogenation and enhance conversion, whereas the presence of Ga was necessary to attenuate the reactivity of the surface to improve selectivity and catalyst stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Highly Robust and Efficient Blechert-Type Cyclic(alkyl)(amino)carbene Ruthenium Complexes for Olefin Metathesis

The first Blechert-type ruthenium complexes containing cyclic(alkyl)(amino)carbene (CAAC) ligands are reported. Furthermore, these catalysts demonstrate remarkable thermal stability in solution and excellent catalytic performances at low catalytic loading (up to 0.005 mol%) in ring-closing metathesis (RCM), macro-RCM, ring-closing enyne metathesis (RCEYM), cross-metathesis (CM), ethenolysis and ring-opening cross metathesis (ROCM). Moreover, up to 95% ee was obtained in asymmetric ring-opening cross metathesis (AROCM) and 57% ee asymmetric cross-metathesis (ACM)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of platinum catalyst supported on carbon nanoballs prepared by solution plasma processing

In order to improve the energy-conversion efficiency in fuel cells, the authors loaded Pt nanoparticles on carbon nanoballs (CNBs) by using solution plasma processing (SPP) involving CNB and Pt ion with a protection group. In this study, we employed poly(vinylpyrrolidone) (PVP) or sodium dodecyl sulfate (SDS) to prepare Pt nanoparticles supported on CNB (Pt/CNB) by the SPP, and the electrochemical properties as a catalyst was evaluated by cyclic voltammetry. The carbon nanoballs were prepared by thermal decomposition process of ethylene and hydrogen gases. Color of the solution changed from yellow to dark brown as synthesis time. This change indicates the improvement of dispersibility of CNB. Moreover, transmission electron microscopy images and elemental mapping images showed the Pt nanoparticles supported on CNB. A catalytic activity of the Pt/CNB in use of SDS was shown to be higher than the Pt/CNB prepared with PVP system. The SDS-containing Pt/CNB also showed the higher activity than that obtained by the conventional method.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Carbon-pore-sheathed cobalt nanoseeds: An exceptional and durable bifunctional catalyst for zinc-air batteries

Exceptional and durable catalysts for Zinc-air batteries are plagued by nanoparticle agglomeration. As a proof-of-concept, we designed carbon-pore-sheathed cobalt nanoseeds by loading cobalt nanoparticles into N-doped defective carbon pores. Introduced N-doping, Co-N-C bond and graphitic/graphenic carbon defects endow the catalyst with exceptional catalytic activity. Most importantly, the design of Co confined within carbon pores effectively solved the dilemma of nanomaterial stability. By balancing the high catalytic activity and stable cyclability, this unique catalyst is among the outstanding bifunctional catalysts, with a high ORR half-wave potential of 0.847 V and a low OER potential at 10 mA/cm 2 of 1.593 V. As demonstrated in the full cell, a peak power density of 135 mW/cm 2 at a current density of 200 mA/cm 2 and 450 h of stable cycling performance without fading at a current density of 30 mA/cm 2 was delivered.

25 ENERGY STORAGE↗

Synthesis and Characterization of Mixed-Conducting Corrosion Resistant Oxide Supports

An extensive search and evaluation of electrochemically stable catalyst supports (including metal oxides like RuO2-SiO2, RuO2-TiO2, and ITO was perfomed during the 4 years of the project. The suports were also catalyzed by deposition of Pt and tested for its performance and electrochemical stability in RDE and fuel cell experiments. For testing the electrochemical stability and fuel cell performance of the catalysts and supports, we have employed the protocols in use at the Department of Energy and Nissan Technological Center North America (NTCNA). The use of such procedures allows a precise and reproducible estimation of the performance and stability of the materials and permits comparisons among laboratories and DOE funded projects. RuO2-SiO2 catalyst supports showed no loss in surface area during start-stop stability tests that were performed by cycling the electrode potential between 0 V to 1.8 V for 1000 cycles. Catalyzed support (40% Pt/RuO2-SiO2; 1:1 mole ratio) were tested in a PEFC, resulting in a current density of 750 mA/cm2 at 0.6 Volts, and a maximum power density of 570 mW/cm2. Measurements were conducted at 80 ºC with 75% relative humidity of the inlet gases (H2/O2); Pt loadings were 0.4 mg/cm2 at the cathode and 0.2 mg/cm2 at the anode. Start-stop stability tests for support and catalyzed support performed in RDE and PEFC set-ups have confirmed RuO2-TiO2 support stability. The beginning of life performance was exactly equal to end of life performance (in an MEA that has been subjected to severe start-stop cycling for 10,000 start/stop cycles between 1 V to 1.5 V). This result was in sharp contrast to baseline Pt/C catalyst that showed significant performance deterioration after accelerated stability tests. The Pt/TRO showed minimal loss in performance upon exposure to start-stop cycles. The loss in cell voltage at 1 A/cm2 at 100% RH was almost 700 mV for Pt/C whereas it was only ca. 15 mV for Pt/TRO. 40% RH data (of inlet gases) revealed a similar trend in terms of stability – exceptional stability for Pt/TRO as opposed to very poor stability for Pt/HSAC. These observations were attributed to the much higher stability of the TRO support compared to Carbon. The carbon dioxide concentration in the cathode exit stream during the accelerated degradation test with Pt/TRO (start-stop protocol) was extremely low (between 3 to 10 ppm of CO2). In contrast, the CO2 emission levels from a conventional Pt/C catalyst were found to be approx. 200 ppm. This observation was a clear indicator that the main source of carbon being oxidized to carbon dioxide in an MEA was the carbon catalyst support, and not the gas diffusion layer or the graphite flow fields. Indium tin oxide (ITO) was also evaluated as a catalyst support for PEFCs. Pt/ITO was very stable under start-up/shutdown accelerated degradation protocol (RDE tests in perchloric acid). The ECSA change was less than 4% over 10,000 cycles. The load cycling accelerated protocol (from 0.6 to 0.95 V vs. RHE) resulted in a loss of approximately 34% of the initial ECSA after 10,000 cycles. However, fuel cell testing resulted in a very low performing catalyst. XPS spectroscopy was employed to investigate the changes in the catalysts occuring during fuel cell operation. It was observed a shift of In 3d5/2 and In 3d3/2 peaks towards higher binding energies. This can be explained by the formation of hydroxides or oxy-hydroxides in the surface of the catalyst. O1s spectrum for Pt/ITO catalyst after being operated in the fuel cell, also confirmed the formation of significant amounts of surface hydroxides (12 to 16%). The presence of surface hydroxides in the catalyst increased the electrode resistivity affecting fuel cell performance. NTCNA performed a detailed analysis of transport phenomena (reactants and products to/from the Pt active sites) in both commercial catalyst and Pt/RTO (in order to have a better understanding at the basic level). The proton resistance (Rionomer) in Pt/C and Pt/RTO cathode catalyst layers were 150 and 12 mΩ-cm2, respectively. Pt/RTO catalyst layer has about an order or magnitude lower proton transfer resistance than Pt/C catalyst layer. Since the ionomer/support ratio that was used in formulating the ink for both catalysts was the same (0.9), it is expected that the volumetric coverage of ionomer of both catalysts will be significantly different due to the disparity in the surface areas (Pt/C had ~ 800 m2/g, while Pt/RTO had ~ 50 m2/g). The differences in the ionomer volumetric coverage and the ionomer film thickness may explain the significantly higher proton conductivity in the Pt/RTO catalyst layer when compared to Pt/HSAC. It is therefore very important to optimize the ionomer loadings when synthesizing new catalyst supports (and never rely on values for carbon-based commercial catalysts). Finally, NTCNA has elaborated a cost model for non-carbon support materials considering their durability benefits. Material costs for production of Pt/ RuO2-TiO2 electrodes were compared to Pt/C. RuO2-TiO2 support was more expensive than carbon but the total material cost was still dominated by platinum cost. Though ruthenium is considered a precious metal, its cost is far less than platinum. It should also be noted that ruthenium only makes up 38% of the mass of the support, while the rest is inexpensive TiO2. After considering the durability advantages of Pt/RTO, cost model showed that even with almost double the Pt loading (0.35 vs 0.18 mgPt/cm2), Pt/RTO ($22.7/kWnet) is only slightly more expensive than Pt/C ($21.9/kWnet).

08 HYDROGEN↗

Synthesis and characterization of novel WO{sub 3} loaded Ag–ZnO and its photocatalytic activity

Graphical abstract: Display Omitted Highlights: ► A novel WO{sub 3} loaded Ag–ZnO was prepared by a simple solvothermal method. ► ‘Ag’ traps the electron from both ZnO and WO{sub 3} reducing electro–hole recombination. ► WO{sub 3}–Ag–ZnO is more efficient than Ag–ZnO, WO{sub 3}–ZnO, Ag–WO{sub 3} and undoped catalysts. ► WO{sub 3}–Ag–ZnO material will be much useful for the treatment of dye effluents. -- Abstract: A novel WO{sub 3} loaded Ag–ZnO photocatalyst was successfully synthesized by a simple solvothermal method and characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM) images, energy dispersive spectrum (EDS), diffuse reflectance spectra (DRS), photoluminescence spectra (PL), cyclic voltammetry (CV) and Brunauer–Emmett–Teller (BET) surface area measurements. The photocatalytic activity of WO{sub 3}–Ag–ZnO was investigated for the degradation of RR 120 and RO 4 dyes in aqueous solution using UV-A light. WO{sub 3}–Ag–ZnO is found to be more efficient than Ag–ZnO, WO{sub 3}–ZnO, Ag–WO{sub 3}, commercial ZnO, prepared ZnO, TiO{sub 2}-P25 and TiO{sub 2} (Merck) at neutral pH for the mineralization of dyes. First time we have reported that novel WO{sub 3} loaded Ag–ZnO has been found to be very efficient for two azo dyes removal when compared to commercially available catalyst (Degussa P25, ZnO (Merck) and TiO{sub 2} (Merck)). The mineralization of dyes has been confirmed by chemical oxygen demand (COD) measurements. A mechanism of degradation has been proposed for the higher efficiency of WO{sub 3}–Ag–ZnO.

36 MATERIALS SCIENCE↗

Atomic Layer Deposition Overcoating Improves Catalyst Selectivity and Longevity in Propane Dehydrogenation

Propylene, a precursor for commodity chemicals and plastics, is produced by propane dehydrogenation (PDH). An increase in PDH yield via added catalyst activity, lifetime, or selectivity represents significant energy and economic savings. Using Pt dispersed on Al2O3 extrudate supports as a commercially relevant model system, we demonstrate that atomic layer deposition (ALD) metal oxide overcoats, used to tailor metal-active sites, can increase PDH yield and selectivity. We investigate the interplay of Pt loading, ALD overcoat thickness, and Al 2 O 3 support surface area on PDH activity, selectivity, and catalyst stability to show that applying a 6-8 A thick layer of Al 2 O 3 on low-surface area Al 2 O 3 supports of similar to 90 m 2 /g surface area yields the optimal combination of stability and activity, while increasing propylene selectivity from 91 to 96%. Increased stability upon steaming deactivation occurs because the Al 2 O 3 overcoat prevents the Pt nanoparticles from sintering. We speculate that the ALD overcoat selectively binds to the undercoordinated sites on the Pt nanoparticles, while leaving the more selective terrace sites available for dehydrogenation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Harnessing photoenzymatic reactions for unnatural biosynthesis in microorganisms

Photobiocatalysis provides a powerful strategy for integrating light and biological catalysts to drive abiological transformations. However, its scalability is hindered by high enzyme loading, reliance on costly cofactors and instability under radical-generating conditions. Here we report the integration of light-driven enzymatic reactions into the cellular metabolism of Escherichia coli, bridging flavin-based photobiocatalysis with biosynthesis. Using synthetic biology strategies, we engineered microbial cells to continuously produce olefin substrates and ene-reductase while regenerating cofactors directly from glucose. By externally supplying radical precursors or introducing synthetic pathways for their in situ production, we enabled fermentation-based microbial photobiosynthesis, achieving high titres and demonstrating feasibility for scale-up in a bioreactor. This approach extends photobiocatalysis from in vitro applications to in vivo semi- and complete biosynthesis, revealing its full potential for integrating light-driven reactions into cellular metabolism.

Biocatalysis↗

Identification of the structure of the Bi promoted Pt non-oxidative coupling of methane catalyst: a nanoscale Pt 3 Bi intermetallic alloy

Recently, stable non-oxidative conversion of methane (NOCM) for up to 8 h with a C 2 selectivity greater than 90% has been reported over Pt–Bi/ZSM-5 at moderate temperatures (600–700 °C). In this study, we demonstrate that the structure of the bimetallic nanoparticles on Pt–Bi/ZSM-5 catalyst is similar to Pt–Bi/SiO 2 . EXAFS indicates the formation of Pt-rich bimetallic Pt–Bi nanoparticles with Pt–Bi bond distance of 2.80 Å. The XRD spectra (on SiO 2 ) are consistent with cubic, intermetallic surface Pt 3 Bi phase on a Pt core. The Pt 3 Bi structure is not known in the thermodynamic phase diagram. In all catalysts, only a small fraction of Bi alloys with Pt. At high Bi loadings, excess Bi reduces at high temperature, covering the catalytic surface leading to a loss in activity. At lower Bi loadings with little excess Bi, the Pt 3 Bi surface is effective for non-oxidative coupling of CH 4 (on ZSM-5) and propane dehydrogenation (on SiO 2 ).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Activity and selectivity control by niobium for the preferential oxidation of co on pt supported catalysts

The promotional effect of Nb on Pt supported on alumina or on niobia, was studied for the preferential oxidation of CO (PROX) in hydrogen. The results show a unique effect of Nb as a promoter to Pt. At low Nb loadings on Pt/alumina, the CO oxidation activity and selectivity are significantly increased. The CO selectivity is 100% at conversions up to about 60%. For Pt supported on Nb{sub 2}O{sub 5}, however, the CO oxidation activity is strongly suppressed with low CO conversion but high H{sub 2} oxidation activity. Pt on niobia, therefore, is poorly selective for the PROX reaction, but is an active hydrogen oxidation catalyst, resistant to CO poisoning. For Pt supported on highly loaded Nb-alumina or Nb{sub 2}O{sub 5}, XPS indicate an increase in the Pt and Nb oxidation states. These surface changes also correlate with changes in the DRIFTS spectra suggesting that CO is more weakly adsorbed on Pt/Nb{sub 2}O{sub 5} compared to Pt/Al{sub 2}O{sub 3}, or Pt/Nb-Al{sub 2}O{sub 3}.

08 HYDROGEN↗

High Load Expansion of Catalytic EGR-Loop Reforming under Stoichiometric Conditions for Increased Efficiency in Spark Ignition Engines

The use of fuel reformate from catalytic processes is known to have beneficial effects on the spark-ignited (SI) combustion process through enhanced dilution tolerance and decreased combustion duration, but in many cases reformate generation can incur a significant fuel penalty. In a previous investigation, the researchers showed that, by controlling the boundary conditions of the reforming catalyst, it was possible to minimize the thermodynamic expense of the reforming process, and in some cases, realize thermochemical recuperation (TCR), a form of waste heat recovery where exhaust heat is converted to usable chemical energy. The previous work, however, focused on a relatively light-load engine operating condition of 2000 rpm, 4 bar brake mean effective pressure (BMEP). The present investigation demonstrates that this operating strategy is applicable to higher engine loads, including boosted operation up to 10 bar BMEP. By controlling the reforming catalyst boundary conditions, it is possible to achieve fuel reforming without experiencing high temperature exotherms that could be damaging to the catalyst. Additionally, the thermodynamic air handling consequences of operating a highly dilute strategy at high loads is quantified. Furthermore the results confirm that this operating strategy provides an efficiency benefit at all conditions investigated, with relative efficiency increases of 3-6%, and is therefore applicable over wider regions of the engine operating map.

42 ENGINEERING↗

Carboxylic acid ligand substituent impacts hydrosilylation activity of platinum single atom catalysts on ceria

Current industrially employed hydrosilylation catalysts rely on homogeneous platinum catalysts which are not recovered after the reaction. To eliminate this issue, our group has been working to optimize recyclability of heterogeneous platinum single atom catalysts (SACs) on ceria via 1,10-phenanthroline-5,6-dione ligands (PDO), which incorporates mono (PDO-C) and dicarboxylic acid (PDO-C2) groups in the 2- and 9-position of PDO ligand to increase metal–surface interaction. DRIFTS results confirm carboxylic acid coordination to the terminal hydroxy groups of the ceria surface. New catalyst synthesis conditions wherein PDO was combined with the metal prior to exposure to the surface allow control of Pt oxidation state on the surface. Here, the highest metal loading was observed for PDO and PDO-C, correlating with improved catalytic recyclability compared to the PDO-C2 ligand. It is proposed that the location of the carboxylic acid groups and the steric effects can explain the lower activity and metal loading for PDO-C2 ligands. Post-reaction XPS and DRIFTS spectra show the appearance of new Si and O species on the catalyst during the hydrosilylation reaction, indicating the silane reagent is depositing on the surface. The silane coverage and leaching of catalyst from the surface is the cause for the reduced catalytic activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗