Search NASA⌕ Search

SEARCH · Search NASA

Results for “compositional”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Microstructure evolution and properties of graphene nanoplatelets reinforced aluminum matrix composites

Highlights: • Lamellar structure of GNPs fibers and Al matrix was obtained in the rolling direction. • Stacking faults were observed in Al grains due to greatly increased GNPs/Al interfaces. • Strength of Al-0.2 wt% GNPs increased 36.8% with negligible electrical conductivity loss. - Abstract: Aluminum matrix composites reinforced with graphene nanoplatelets (GNPs) were prepared by continuous casting and subsequent rolling. Al-GNPs master alloy, prepared by ball milling and cold pressing, was added into Al melts to fabricate the composites. Microstructure evolution of the composites were observed using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron back scattered diffraction (EBSD). GNPs distributed uniformly in the as-cast specimen and then transformed into fibers in the rolling direction after deformation and finally a lamellar structure formed in the composites. Raman spectra showed that the structural damage of GNPs mainly came from ball milling. The interface between GNPs and Al was well combined in general while a few microcracks were observed, which reduced the ductility of the composites and no adverse aluminum carbide (Al{sub 4}C{sub 3}) was detected at the interface. Stacking faults were observed interior of the aluminum grain, which may due to the existence of plentiful interface introduced by GNPs. Fracture observation revealed that the load transferred from Al matrix to GNPs. The ultimate tensile strength of Al-0.2 wt% GNPs composites was about 36.8% higher than that of pure Al with the same casting and rolling process, which should result from the lamellar structure and load transfer, while the conductivity of the composites decreased slightly, indicating that interface scattering between Al and GNPs is very limited. The investigation results show that Al-GNPs composite is potential for high strength and high conductivity application.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of boric acid on the properties of Li{sub 2}MnO{sub 3}·LiNi{sub 0.5}Mn{sub 0.5}O{sub 2} composite cathode powders prepared by large-scale spray pyrolysis with droplet classifier

Graphical abstract: Display Omitted Highlights: ► Spherical shape Li{sub 2}MnO{sub 3}·LiNi{sub 0.5}Mn{sub 0.5}O{sub 2} composite cathode powders are prepared by large-scale spray pyrolysis with droplet classifier. ► Boric acid improves the morphological and electrochemical properties of the composite cathode powders. ► The discharge capacity of the composite cathode powders decreases from 217 to 196 mAh g{sup −1} by the 30th cycle. -- Abstract: Spherically shaped 0.3Li{sub 2}MnO{sub 3}·0.7LiNi{sub 0.5}Mn{sub 0.5}O{sub 2} composite cathode powders with filled morphology and narrow size distribution are prepared by large-scale spray pyrolysis. A droplet classification reduces the standard deviation of the size distribution of the composite cathode powders. Addition of boric acid improves the morphological properties of the product powders by forming a lithium borate glass material with low melting temperature. The optimum amount of boric acid dissolved in the spray solution is 0.8 wt% of the composite powders. The powders prepared from the spray solution with 0.8 wt% boric acid have a mixed layered crystal structure comprising Li{sub 2}MnO{sub 3} and LiNi{sub 0.5}Mn{sub 0.5}O{sub 2} phases, thus forming a composite compound. The initial charge and discharge capacities of the composite cathode powders prepared from the 0.8 wt% boric acid spray solution are 297 and 217 mAh g{sup −1}, respectively. The discharge capacity of the powders decreases from 217 to 196 mAh g{sup −1} by the 30th cycle, in which the capacity retention is 90%.

36 MATERIALS SCIENCE↗

The AMWCNTs supported porous nanocarbon composites for high-performance supercapacitor

Graphical abstract: The AMWCNTs supported porous nanocarbon composites were prepared by a easy method. The composites had shown good performances for electrochemical energy storage with high specific capacitance and good stability. - Highlights: • The AMWCNTs supported porous nanocarbon composites were prepared. • The composites have good conductivity and large BET specific surface areas. • The composites had shown high specific capacitance, and good stability. - Abstract: The porous nanocarbons supported by acid-treated multiwall carbon nanotubes (PC@ACNTs) were prepared by the combination of the hydrothermal polymerization of glucose on ACNTs, carbonization under N{sub 2} protection and final activation with ZnCl{sub 2}. The materials were characterized by transmission electron microscopy, X-ray powder diffraction and Raman spectra. The results indicated that the ACNTs distributed uniformly into the framework of the porous carbon. The composites showed the high BET specific surface area up to 1712 m{sup 2} g{sup −1} and good conductivity. The electrochemical measurements indicated that the composites processed good performances for electrochemical energy storage (210 F g{sup −1} at 0.5 A g{sup −1}), and high stability (>99.9%), much higher than the corresponding ACNTs, porous carbons and the samples prepared by using raw MWCNTs as source. The good performance of PC@ACNTs composites was relative with the synergy of good conductivity of ACNTs and large specific surface areas of PC.

36 MATERIALS SCIENCE↗

Copper ions removal from water using functionalized carbon nanotubes–mullite composite as adsorbent

Highlights: • CNTs–mullite composite was prepared via chemical vapor deposition (CVD) method. • The prepared composite was modified with concentrated nitric acid and chitosan. • The modified CNTs–mullite composites were used as novel adsorbents. • Copper ion removal from water by the prepared adsorbents was performed. • Langmuir and Freundlich isotherms and two kinetic models were applied to fit the experimental data. - Abstract: Carbon nanotubes–mullite composite was synthesized by direct growth of carbon nanotubes on mullite particles via chemical vapor deposition method using cyclohexanol and ferrocene as carbon precursor and catalyst, respectively. The carbon nanotubes–mullite composite was oxidized with concentrated nitric acid and functionalized with chitosan and then used as a novel adsorbent for copper ions removal from water. The results demonstrated that modification with concentrated nitric acid and chitosan improves copper ions adsorption capacity of the prepared composite, significantly. Langmuir and Freundlich isotherms and two kinetic models were applied to fit the experimental data. The carbon nanotubes growth on mullite particles to form the carbon nanotubes–mullite composite with further modification is an inherently safe approach for many promising environmental applications to avoid some concerns regarding environment, health and safety. It was found that the modified carbon nanotubes–mullite composite can be considered as an excellent adsorbent for copper ions removal from water.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Preparation of graphene/WO3/TiO2 composite and its photocathodic protection performance for 304 stainless steel

Highlights: • TiO{sub 2} nanoparticles and WO{sub 3} nanorods were immobilized onto graphene by the hydrothermal method. • The composite can provide an effective protection for 304 stainless steel under visible light. • The composite can offer a sufficient cathodic protection even in the dark. • Possible photocathodic protection mechanism of graphene/WO{sub 3}/TiO{sub 2} composite was proposed. - Abstract: Graphene/WO{sub 3}/TiO{sub 2} composite (RGO/WO{sub 3}/TiO{sub 2}) was successfully fabricated via a two-step hydrothermal method. The structure, morphology and optical property of the as-prepared composite were characterized by X-ray powder diffraction, fourier transform infrared spectra, Raman spectra, transmission electron microscope, scanning electron microscope and ultraviolet-visible diffuse reflectance spectra, respectively. Results showed that the composite was incorporated by graphene nanosheets, WO{sub 3} nanorods and TiO{sub 2} nanoparticles. It exhibited favorable absorption ability in both UV and visible light region. The photocathodic protection performance for 304 stainless steel (304SS) was proven by photocurrent density, open circuit potential, Tafel polarization curves and electrochemical impedance spectroscopy. It was found that the composite could provide an efficient protection for 304SS under visible light irradiation and even in the dark compared to the pure TiO{sub 2}. The electrode potentials negatively shifted to −760 mV under visible light. The possible photocathodic protection mechanism of the composite was also proposed.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Minor titanium addition markedly improves the co-deformability of copper-tantalum composites

We investigated the microstructures of equal channel angular extrusion (ECAE) processed sintered composites of copper (Cu) and tantalum (Ta). These composites were produced with nominal Ta volume percentages ranging from 25% to 75%. Additional composites of the same nominal Ta content were prepared with a minor amount of titanium (Ti) added to facilitate interphase bonding. Ti addition was found to markedly improve the strength and co-deformability of the composites, allowing reliable extrusion of Cu-Ta composites with novel microstructures. A major influence of the Ti appears to be to soften the Ta, which contributes to improved co-deformability by reducing the flow stress mismatch between the composite constituents. Here, a change in the fracture surface morphology in the Ti-modified composite compared to the unmodified composite suggests that the Ti may also improve cohesion between Cu and Ta by reducing Ta surface oxides.

36 MATERIALS SCIENCE↗

Compositional Models of Glass/Melt Properties and their Use for Glass Formulation

Nuclear waste glasses must simultaneously meet a number of criteria related to their processability, product quality, and cost factors. The properties that must be controlled in glass formulation and waste vitrification plant operation tend to vary smoothly with composition allowing for glass property-composition models to be developed and used. Models have been fit to the key glass properties. The properties are transformed so that simple functions of composition (e.g., linear, polynomial, or component ratios) can be used as model forms. The model forms are fit to experimental data designed statistically to efficiently cover the composition space of interest. Examples of these models are found in literature. The glass property-composition models, their uncertainty definitions, property constraints, and optimality criteria are combined to formulate optimal glass compositions, control composition in vitrification plants, and to qualify waste glasses for disposal. An overview of current glass property-composition modeling techniques is summarized in this paper along with an example of how those models are applied to glass formulation and product qualification at the planned Hanford high-level waste vitrification plant.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Codes and standards for ceramic composite core materials for High Temperature Reactor applications

Fiber-reinforced ceramic matrix composites are attractive for high-temperature nuclear applications due to excellent thermal and mechanical properties as well as reasonable-to-outstanding radiation resistance. Over the past 20 years, the use of ceramic matrix composite applications expanded to many commercial non-nuclear industries as fabrication and application of the technologies mature. The ASME Boiler Pressure Vessel Code, under Section III Division 5, provides the design and construction rules for High Temperature Reactor components. It published the first rules for ceramic matrix composites to be used for reactor core components. The rules lay out the quality requirements together with the design and materials criteria for the use and application of silicon carbide- and carbon-based matrix material technologies. As with the established graphite rules, the ceramic composite material rules are structured in Subsection HH (from Section III), that addresses the criteria for class SN nonmetallic core components. The code rules rely heavily on the development and publication of standards for composite specification, classification, and testing of mechanical, thermal, and other properties. These test methods are developed in ASTM Committee C28 on Advanced Ceramics, with a current focus on ceramic composite tubes. This article describes the detail of the composites code, the design methodology and similarities to the graphite code, the guidance for the development of specifications for ceramic composites (for nuclear applications) including recent standard developments, and it mentions the next steps to support licensing aspects by validating the code with benchmarking data.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Composition–Structure–Activity Correlation of Platinum–Ruthenium Nanoalloy Catalysts for Ethanol Oxidation Reaction

Understanding the evolution of the composition and atomic structure of nanoalloy catalysts in the ethanol oxidation reaction (EOR) is essential for the design of active and robust catalysts for direct ethanol fuel cells. This article describes a study of carbon-supported platinum–ruthenium electrocatalysts (PtRu/C) with different bimetallic compositions and their activities in the EOR, an important anode reaction in direct ethanol fuel cells (DEFCs). The study focused on establishing the relationship between the catalyst’s composition, atomic structure, and catalytic activity for the EOR. Ex situ and in situ synchrotron high-energy X-ray diffraction (HE-XRD) experiments coupled with atomic pair distribution function (PDF) analysis and in situ energy-dispersive X-ray (EDX) analysis were employed to probe the composition and structural evolution of the catalysts during the in situ EOR inside a membrane electrode assembly (MEA) in the fuel cell. The results revealed an intriguing composition–structure–activity relationship for the PtRu electrocatalysts under EOR experimental conditions. In particular, the alloy with a Pt/Ru ratio of ~50:50 was found to exhibit a maximum EOR activity as a function of the bimetallic composition. This composition–activity relationship coincides with the relationship between the Pt interatomic distances and coordination numbers and the bimetallic composition. Notably, the catalytic activities of the PtRu electrocatalysts showed a significant improvement during the EOR, which can be related to atomic-level structural changes in the nanoalloys occurring during the EOR, as indicated by in situ HE-XRD/PDF/EDX data. Here, the findings shed some new light on the mechanism of the ethanol oxidation reaction over bimetallic alloy nanocatalysts, which is important for the rational design and synthesis of active nanoalloy catalysts for DEFCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis and characterization of (Ga 1-x Zn x )(N 1-x O x ) nanocrystals with a wide range of compositions

We describe the synthesis and characterization of wurtzite (Ga 1-x Zn x )(N 1-x O x ) nanocrystals with a wide range of compositions and a focus on properties relevant for solar fuel generation. (Ga 1-x Zn x )(N 1-x O x ), a solid solution of GaN and ZnO, is an intriguing material because it exhibits composition-dependent visible absorption even though the parent semiconductors absorb in the UV. When functionalized with co-catalysts, (Ga 1-x Zn x )(N 1-x O x ) is also capable of water splitting under visible irradiation. Here, we examine the synthesis of (Ga 1-x Zn x )(N 1-x O x ) nanocrystals to understand how they form by nitridation of ZnO and ZnGa 2 O 4 nanocrystalline precursors. We find that the ZnO precursor is critical for the formation of crystalline (Ga 1-x Zn x )(N 1-x O x ) at 650 °C, consistent with a mechanism in which wurtzite (Ga 1-x Zn x )(N 1-x O x ) nucleates topotactically on wurtzite ZnO at an interface with ZnGa 2 O 4 . Using this information, we expand the range of compositions from previously reported 0.30 ≤ x ≤ 0.87 to include the low-x and high-x ends of the range. The resulting compositions, 0.06 ≤ x ≤ 0.98, constitute the widest range of (Ga 1-x Zn x )(N 1-x O x ) compositions obtained by one synthetic method. We then examine how the band gap depends on sample composition and find a minimum of 2.25 eV at x = 0.87, corresponding to a maximum possible solar-to-H 2 power conversion efficiency of 12%. Finally, we examine the photoelectrochemical (PEC) oxidation behavior of thick films of (Ga 1-x Zn x )(N 1-x O x ) nanocrystals with x = 0.40, 0.52, and 0.87 under visible illumination. (Ga 1-x Zn x )(N 1-x O x ) nanocrystals with x = 0.40 exhibit solar PEC oxidation activity that, while too low for practical applications, is higher than that of bulk (Ga 1-x Zn x )(N 1-x O x ) of the same composition. The highest photocurrents are observed at x = 0.52, even though x = 0.87 absorbs more visible light, illustrating that the observed photocurrents are a result of an interplay of multiple parameters which remain to be elucidated. This set of characterizations provides information useful for future studies of composition-dependent PEC properties of nanoscale (Ga 1-x Zn x )(N 1-x O x ).

36 MATERIALS SCIENCE↗

Development of nickel-incorporated MCM-41–carbon composites and their application in nitrophenol reduction

MCM-41–carbon composites were obtained by soft-templating strategy by adding resorcinol and formaldehyde as carbon precursors during the synthesis of MCM-41. The synthesis of these composites was optimized until mesoporous MCM-41 domains remained highly ordered and the overall specific surface area and pore volume remained relatively high. The one-pot synthetic procedure was further extended to obtain the Ni-containing MCM-41–carbon composites using nickel nitrate as an additive. A homogeneous distribution of nickel nanoparticles in the composites was achieved by adding histidine to the reaction mixture, which was able to form a complex with nickel ion. Carbonization of organic components in the composites produced carbon that was responsible for in situ reduction of nickel(II) to metallic nickel (Ni0) at elevated temperatures, eliminating the post-synthesis reduction step carried out in the presence of hydrogen gas or other reducing agent. Furthermore, the resulting composites showed enhanced catalytic activity toward nitrophenol reduction obeying the zero-order kinetics. Three unique features of the resulting composites, namely mesoporous channels of MCM-41, carbon-induced in situ reduction of Ni ions to metallic Ni nanoparticles, and abundance of highly active Ni sites due to high dispersion of Ni0, make this strategy applicable for the synthesis of other transition metal-based catalysts. XRD and STEM analyses revealed a homogeneous distribution of nickel nanoparticles in the composites without significant distortion of their ordered mesoporosity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Vapor-liquid-solid epitaxial growth of Si 1-x Ge x alloy nanowires. Composition dependence on precursor reactivity and morphology control for vertical forests

The growth of high-density group IV alloy nanowire forests is critical for exploiting their unique functionalities in many applications. Here, the compositional dependence on precursor reactivity and optimized conditions for vertical growth are studied for Si 1- x Ge x alloy nanowires grown by the vapor-liquid-solid method. The nanowire composition versus gas partial-pressure ratio for germane-silane and germane-disilane precursor combinations is obtained at 350°C over a wide composition range (0.05 ≤ x ≤ 0.98) and a generalized model to predict composition for alloy nanowires is developed based on the relative precursor partial pressures and reactivity ratio. In combination with germane, silane provides more precise compositional control at high Ge concentrations (x > 0.7), whereas disilane greatly increases the Si concentration for a given gas ratio and enables more precise alloy compositional control at small Ge concentrations (x < 0.3). Vertically oriented, non-kinking nanowire forest growth on Si (111) substrates is then discussed for silane/germane over a wide range of compositions, with temperature and precursor partial pressure optimized by monitoring the nanowire growth front using in-situ optical reflectance. For high Ge compositions (x ≈ 0.9), a “two-step” growth approach with nucleation at higher temperatures results in nanowires with high-density and uniform vertical orientation. Furthermore, increasing Si content (x ≈ 0.8), the optimal growth window is shifted to higher temperatures, which minimizes nanowire kinking morphologies. For Si-rich Si 1- x Ge x alloys (x ≈ 0.25), vertical nanowire growth is enhanced by single-step, higher-temperature growth at reduced pressures.

36 MATERIALS SCIENCE↗

Evolution of AlGaN deep level defects as a function of alloying and compositional grading and resultant impact on electrical conductivity

AlGaN:Si epilayers with uniform Al compositions of 60%, 70%, 80%, and 90% were grown by metal-organic vapor phase epitaxy along with a compositionally graded, unintentionally doped (UID) AlGaN epilayer with the Al composition varying linearly between 80% and 100%. The resistivity of AlGaN:Si with a uniform composition increased significantly for the Al content of 80% and greater, whereas the graded UID-AlGaN film exhibited resistivity equivalent to 60% and 70% AlGaN:Si owing to polarization-induced doping. Deep level defect studies of both types of AlGaN epilayers were performed to determine why the electronic properties of uniform-composition AlGaN:Si degraded with increased Al content, while the electronic properties of graded UID-AlGaN did not. The deep level density of uniform-composition AlGaN:Si increased monotonically and significantly with the Al mole fraction. Conversely, graded-UID AlGaN had the lowest deep level density of all the epilayers despite containing the highest Al composition. These findings indicate that Si doping is an impetus for point defect incorporation in AlGaN that becomes stronger with the increasing Al content. However, the increase in deep level density with the Al content in uniform-composition AlGaN:Si was small compared to the increase in resistivity. This implies that the primary cause for increasing resistivity in AlGaN:Si with the increasing Al mole fraction is not compensation by deep levels but rather increasing activation energy for the Si dopant. As a result, the graded UID-AlGaN films maintained low resistivity because they do not rely on thermal ionization of Si dopants.

36 MATERIALS SCIENCE↗

Room temperature multiferroicity and magnetodielectric coupling in 0–3 composite thin films

Magnetoelectric (ME) composite thin films are promising candidates for novel applications in future nanoelectronics, spintronics, memory and other multifunctional devices as they exhibit much higher ME coupling and transition temperatures (Tc) than well-known single phase multiferroics discovered to date. Among the three types of multiferroic composite nanostructures, (2-2) layered and (1-3) vertically aligned composite nanostructures exhibit comparatively smaller ME coupling due to different shortcomings which restrict their use in many applications. Here we study the morphological, piezoresponse force microscopic (PFM), ferroelectric, magnetic, and magnetodielectric properties of 0-3 (magnetic nanoparticles (0) homogeneously distributed in ferroelectric matrices (3)) multiferroic composite thin films. The Pb(Fe 0.5 Nb 0.5 )O 3 (PFN) - Ni 0.65 Zn 0.35 Fe 2 O 4 (NZFO) particulate composite films were synthesized by pulsed laser deposition (PLD). These particulate composite thin films are completely c-axis oriented with very low surface roughness. We observed magnetic and ferroelectric T c above room temperature (RT) for all composite thin films. The PFN-NZFO 0-3 composites exhibit large polarization, high saturated magnetization with low coercive field, low dielectric loss along with magnetodielectric coupling at RT. These nanocomposites might be utilized in next generation nano/microelectronics and spintronic devices.

36 MATERIALS SCIENCE↗

OXYGEN ISOTOPIC COMPOSITIONS OF SOLAR CORUNDUM GRAINS

Oxygen is one of the major rock-forming elements in the solar system and the third most abundant element of the Sun. Oxygen isotopic composition of the Sun, however, is not known due to a poor resolution of astronomical spectroscopic measurements. Several DELTA{sup 17}O values have been proposed for the composition of the Sun based on (1) the oxygen isotopic measurements of the solar wind implanted into metallic particles in lunar soil (< -20 per mille by Hashizume and Chaussidon and approx +26 per mille by Ireland et al.), (2) the solar wind returned by the Genesis spacecraft (-27 per mille +- 6 per mille by McKeegan et al.), and (3) the mineralogically pristine calcium-aluminum-rich inclusions (CAIs) (-23.3 per mille +- 1.9 per mille by Makide et al. and -35 per mille by Gounelle et al.). CAIs are the oldest solar system solids, and are believed to have formed by evaporation, condensation, and melting processes in hot nebular region(s) when the Sun was infalling (Class 0) or evolved (Class 1) protostar. Corundum (Al{sub 2}O{sub 3}) is thermodynamically the first condensate from a cooling gas of solar composition. Corundum-bearing CAIs, however, are exceptionally rare, suggesting either continuous reaction of the corundum condensates with a cooling nebular gas and their replacement by hibonite (CaAl{sub 12}O{sub 19}) or their destruction by melting together with less refractory condensates during formation of igneous CAIs. In contrast to the corundum-bearing CAIs, isolated micrometer-sized corundum grains are common in the acid-resistant residues from unmetamorphosed chondrites. These grains could have avoided multistage reprocessing during CAI formation and, therefore, can potentially provide constraints on the initial oxygen isotopic composition of the solar nebula, and, hence, of the Sun. Here we report oxygen isotopic compositions of approx60 micrometer-sized corundum grains in the acid-resistant residues from unequilibrated ordinary chondrites (Semarkona (LL3.0), Bishunpur (LL3.1), Roosevelt County 075 (H3.2)) and unmetamorphosed carbonaceous chondrites (Orgueil (CI1), Murray (CM2), and Alan Hills A77307 (CO3.0)) measured with a Cameca ims-1280 ion microprobe. All corundum grains, except two, are {sup 16}O-rich (DELTA{sup 17}O = -22.7 per mille +- 8.5 per mille, 2sigma), and compositionally similar to the mineralogically pristine CAIs from the CR carbonaceous chondrites (-23.3 per mille +- 1.9 per mille, 2sigma), and solar wind returned by the Genesis spacecraft (-27 per mille +- 6 per mille, 2sigma). One corundum grain is highly {sup 17}O-enriched (delta{sup 17}O approx +60 per mille, delta{sup 18}O approx -40 per mille) and is probably of the presolar origin; the origin of another {sup 17}O-rich grain (delta{sup 17}O approx -15 per mille , delta{sup 18}O approx -35 per mille) is unclear. We conclude that the {sup 16}O-rich corundum grains in the acid-resistant residues from unequilibrated ordinary and unmetamorphosed carbonaceous chondrites recorded initial oxygen isotopic composition of the solar nebula, and, hence, of the Sun. Our inferred oxygen isotopic composition of the Sun is inconsistent with the more extreme {sup 16}O-rich value (DELTA{sup 17}O approx -35 per mille) proposed by Gounelle et al. on the basis of two extremely {sup 16}O-rich CAIs from the CH/CB-like chondrite Isheyevo and with the {sup 16}O-poor value observed as a component of the solar wind implanted into the metallic particles in lunar soil (Ireland et al.).

79 ASTRONOMY AND ASTROPHYSICS↗

Controls of Wellbore Flow Regimes on Pump Effluent Composition

Where well water and formation water are compositionally different or heterogeneous, pump effluent composition will vary due to partial mixing and transport induced by pumping. Investigating influences of purging and sampling methodology on composition variability requires quantification of wellbore flow regimes and mixing. As a basis for this quantification, analytical models simulating Poiseuille flow were developed to calculate flow paths and travel times. Finite element modeling was used to incorporate influences of mixing. Parabolic velocity distributions within the screened interval accelerate with cumulative inflow approaching the pump intake while an annulus of inflowing formation water contracts uniformly to displace an axial cylinder of pre-pumping well water as pumping proceeds. Increased dispersive mixing forms a more diffuse formation water annulus and the contribution of formation water to pump effluent increases more rapidly. Models incorporating viscous flow and diffusion scale mixing show that initially pump effluent is predominantly pre-pumping well water and compositions vary most rapidly. After two screen volumes of pumping, 94% of pump effluent is inflowing formation water. Where the composition of formation water and pre-pumping well water are likely to be similar, pump effluent compositions will not vary significantly and may be collected during early purging or with passive sampling. However, where these compositions are expected to be considerably different or heterogeneous, compositions would be most variable during early pumping, that is, when samples are collected during low-flow sampling. Purging of two screen volumes would be required to stabilize the content and collect a sample consisting of 94% formation water.

58 GEOSCIENCES↗

Remote Monitoring of the Structural Health of Hydrokinetic Composite Turbine Blades (Final Report)

A health monitoring approach is investigated for hydrokinetic turbine blade applications. In-service monitoring is critical due to the difficult environment for blade inspection and the cost of inspection downtime. Composite blade designs have advantages that include long life in marine environments and great control over mechanical properties. Experimental strain characteristics are determined for static loads and free-vibration loads. These experiments are designed to simulate the dynamic characteristics of hydrokinetic turbine blades. Carbon/epoxy symmetric composite laminates are manufactured using an autoclave process. Four-layer composite beams, eight-layer composite beams, and two-dimensional eight-layer composite blades are instrumented for strain. Experimental results for strain measurements from electrical resistance gages are validated with theoretical characteristics obtained from in-house finite-element analysis for all sample cases. These preliminary tests on the composite samples show good correlation between experimental and finite-element strain results. A health monitoring system is proposed in which damage to a composite structure, e.g. delamination and fiber breakage, causes changes in the strain signature behavior. The system is based on embedded strain sensors and embedded motes in which strain information is demodulated for wireless transmission. In-service monitoring is critical due to the difficult environment for blade inspection and the cost of inspection downtime. Composite blade designs provide a medium for embedding sensors into the blades for in-situ health monitoring. The major challenge with in-situ health monitoring is transmission of sensor signals from the remote rotating reference frame of the blade to the system monitoring station. In the presented work, a novel system for relaying in-situ blade health measurements in hydrokinetic systems is described and demonstrated. An ultrasonic communication system is used to transmit sensor data underwater from the rotating frame of the blade to a fixed relay station. Data are then broadcast via radio waves to a remote monitoring station. Results indicate that the assembled system can transmit simulated sensor data with an accuracy of ±5% at a maximum sampling rate of 500 samples/sec. A power investigation of the transmitter within the blade shows that continuous max-sampling operation is only possible for short durations (~days), and is limited due to the capacity of the battery power source. However, intermittent sampling, with long periods between samples, allows for the system to last for very long durations (~years). Finally, because the data transmission system can operate at a high sampling rate for short durations or at a lower sampling rate/higher duty cycle for long durations, it is well-suited for short-term prototype and environmental testing, as well as long-term commercially-deployed hydrokinetic machines.

13 HYDRO ENERGY↗

Evaluating Effects of Shear Processing on 2D Crystalline Materials in 3D Metal Matrices: Atomistic Understanding of High Shear Deformation of Copper Graphene Composites

Composites made of copper and graphene demonstrate high strength, lubricity and enhanced electrical and thermal conductivity compared pure copper. However, manufacturing these composites at bulk volumes for industrial applications has been a big challenge. Shear deformation assisted processing is an effective method for manufacturing materials such as copper-graphene composites demonstrating ultra-fine grain structures and compositional homogeneity. Nevertheless, microstructural evolution of the composites and their property development under such conditions is not clearly understood currently. To rectify this gap in literature, high strain shear deformation of copper coated graphene foils was performed using a tribometer pin in this study. Changes in microstructure of the composite as well as the constituent components under shear deformation was correlated to process conditions. A sharp increase in the coefficient of friction attributed to rupture and smearing of graphene layer into copper substrate was observed during the shear processing. The coefficient of friction of the sheared copper/graphene composite was lower than that of pure copper, suggesting that partially worn graphene is effectively lubricious at the macroscale. A multimodal characterization of the processed region further revealed a shear deformation-induced ultrafine two-phase grain-structure consisting of copper and graphitic domains. Shear deformation reduced the copper grain size from around 50 – 100 µm to ~200 nm on an average and ~2 – 5 nm in some locations. The semicrystalline graphene films were observed to fracture into 10 – 50 µm size flakes. Oxygen enrichment was observed in the processed region. Finally, graphitic domain were identified for the first time in the copper matrix and not just at the grain boundaries providing evidence for a metastable composite microstructure as a result of solid phase processing at room temperature.

36 MATERIALS SCIENCE↗