Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Derivation of heterogeneous material distributions and their sensitivity to HM-coupled two-phase flow models exemplified with the LASGIT experiment

Abstract Advective gas transport in bentonite, a possible buffer material in repositories for radioactive materials, is difficult to simulate in numerical continuum models, partly due to the complicated microstructure of bentonite. To generate reliable models of repositories nevertheless, spatially distributed heterogeneous material properties can be used to allow localization of gas flow. In this study, a pore-size-dependent stochastic approach of the gas entry pressure is derived from Mercury Intrusion Porosimetry, which is used to replicate measurements from the LASGIT experiment. In addition, three benchmark tests are simulated to investigate the dependence of heterogeneous distributions of material properties on the mesh discretization, the temporal dependence, and the coupling between the processes influenced by the heterogeneous parameters. The numerical modeling results of the LASGIT experiment show that the onset of gas flow into the system and the subsequent increase in pressure and stress can be well reproduced using heterogeneous distributions. Compared to a model with homogeneous material properties, heterogeneous distributions may allow the generation of dilatancy-controlled microfractures—an important feature with regard to the advective gas flow in bentonites. However, it can be observed that the heterogeneous distributions in LASGIT are less significant, as technical gaps or differences in material types could have a greater impact.

Environmental Sciences & Ecology↗

Understanding the deposition mechanism of pulsed laser deposited B-C films using dual-targets

Boron carbide thin films with stoichiometry (boron-carbon atomic ratio) range of 0.1 ∼ 8.9 were fabricated via pulsed laser deposition by using boron-carbon dual-targets. However, this experimental data on stoichiometry were smaller than the computer simulation values. The discrepancy was investigated by studies on composition and microstructure of the thin films and targets by scanning electron microscopy, excitation laser Raman spectroscopy, and X-ray photoelectron spectroscopy. The results indicate that the boron liquid droplets were formed by phase explosion after laser irradiation on boron sector. Part of the boron droplets would be lost via ejection in the direction of laser beam, which is tilted 45° to the surface of substrate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of heat treatment on microstructural evolution and hardness homogeneity in laser powder bed fusion of alloy 718

The thermal history developed in laser powder bed fusion (LPBF) processes has been shown to be complex resulting in equally complex microstructures and mechanical properties. Microscopic observations and Vickers micro-hardness mapping measurements were carried out on diff ;erent section planes of LPBF alloy 718 cuboids. Three-dimensional finite element analysis was used to simulate thermal history and to predict the residual stress distribution in the as-built material. Computational thermodynamics was used to predict the micro-segregation and nucleation driving force of various phases in the bulk and in segregated regions. Varied heat-treatments such as simulated hot isostatic pressing, and double aging were applied. Their influence on the microstructure, microsegregation, precipitate formation, and micro-hardness variations of LPBF alloy 718 were investigated. Hardness map results showed heterogeneous micro-hardness on the xy- and xz-planes of the as-built parts where the bottom plane and center regions had larger hardness of ~315 HV 0.5 while the top plane and contours showed hardness of ~300 HV 0.5 . It was found that the aging treatment increased the overall hardness of the as-built condition from ~310 HV 0.5 to 470 HV 0.5 but also increased the hardness gradient throughout the coupon. After simulated hot isostatic pressing process (i.e., without applied pressure) at 1020 °C for 4 h followed by water quench (HIPWQ), the hardness gradient and hardness was minimized (~210 HV 0.5 ) as the microstructure transitioned from heterogeneous columnar grains in the as-built condition to more uniform recrystallized grains. A double aging treatment was applied to enhance hardness from ~210 HV 0.5 to ~440 HV 0.5 . Finally, HIPWQ followed by double aging produced a homogeneous microstructure and more uniform hardness map with enhanced mechanical properties in LPBF alloy 718 coupons.

36 MATERIALS SCIENCE↗

Design of a separate effects MiniFuel irradiation experiment investigating microstructure evolution in high burnup UO 2

The microstructural evolution of UO 2 fuel pellets during commercial operation in light water reactors (LWRs) is known to vary significantly across the pellet radius due to spatial variations in local temperature and burnup. The primary obstacle to extending LWR refueling cycles to 24-month intervals is the susceptibility of certain high burnup fuel microstructures to fuel fragmentation, relocation, and dispersal (FFRD) during a loss of coolant accident (LOCA). Although FFRD of the high burnup structure in the rim region of a pellet is well studied, the fine fragmentation that has been observed in a second region, near the midradius of the pellet (termed the “dark zone”) following mock LOCA testing of high burnup commercial fuel rods is less understood. This paper describes the design, analysis, and execution of a separate effects MiniFuel irradiation experiment that aims to identify the specific temperature and burnup regimes under which FFRD-susceptible dark zone microstructures form. The small disc specimens (3 mm diameter by ∼0.3 mm thick) enable more precise control of the relatively uniform temperature and burnup conditions. A total of 42 specimens were fabricated with typical LWR fuel densities (∼96%–98% of theoretical density) and grain sizes (∼12 μm) and are being irradiated over a range of temperatures (600°C–1000°C) and discharge burnups (50–72 MWd/kg-U) that bound the midradius region of high burnup LWR fuel. Fuel specimens with identical 235 U enrichments were inserted in two irradiation locations in the High Flux Isotope Reactor and are currently undergoing irradiation to further evaluate the impact of rate effects (fission rate, time at temperature) on the microstructural evolution. The fuel fabrication and the thermal and neutronic simulations used for designing the experiment are detailed in this paper. A secondary objective of the experiment is to observe fission gas release (FGR) under the various irradiation conditions, and this work provides first-order predictions of FGR from all fuel specimens. The insights gained from these experiments will inform future high burnup core designs that could minimize the formation of susceptible microstructures and ultimately enable 24-month refueling cycles while minimizing the fraction of the fuel susceptible to FFRD.

FFRD↗

Computational and Experimental Studies of Microstructure-Scale Porosity in Metallic Fuels for Improved Gas Swelling Behavior

This proposal will investigate the stability of bimodal pore size distributions in metallic uranium and uranium-zirconium alloys during sintering and re-sintering annealing treatments. The project will utilize both computational and experimental approaches. The computational approach includes both Molecular Dynamics simulations to determine the self-diffusion coefficients in pure U and U-Zr alloys in single crystals, grain boundaries, and free surfaces, as well as calculations of grain boundary and free surface interfacial energies. Phase-field simulations using MOOSE will be conducted to study pore and grain structure evolution in microstructures with bimodal pore size distributions. Experiments will also be performed to validate the simulations, and measure the time-dependent densification of bimodal porous compacts.

36 MATERIALS SCIENCE↗

Physics-Informed Machine Learning Model for Ceramic Matrix Composite Creep

A physics-informed recurrent neural network (RNN) based surrogate model is developed to emulate the nonlinear, time-dependent constitutive behavior of ceramic matrix composites (CMCs) driven by matrix damage and constituent creep at the microscale. Physics-informed constraints are introduced into the surrogate model through regularization to ground the prediction in physics and improve its predictive capabilities. Training data is generated using the high-fidelity generalized method of cells (HFGMC) approach which calls appropriate creep and damage models for each of the constituents. This coupling permits simulating the nonlinear behavior of CMCs based on constituent response at the microscale along with microstructural features such as fiber and porosity volume fraction and fiber radius. The microscale repeating unit cell is loaded under creep fatigue conditions to replicate the material loading experienced in a turbine engine. Therefore, the RNN-based surrogate model is tasked with predicting, as a function of variable input stress sequence, temperature, and microstructural features, the resulting strain history response while satisfying physical constraints related to creep rate, isochoric inelastic deformation, and strain energy density. The trained surrogate model is shown to effectively match the strain history over quantified distributions of microstructural features and relevant loading regimes and temperatures. Neural network based surrogate models can offer efficient alternatives to running computationally intensive multiscale material models to simulate the nonlinear response of large structural models. Therefore, the presented work provides evidence towards the feasibility of developing, training, and running such models for CMCs with complex microstructures, nonlinear time-dependent material response, and under non-monotonic loading conditions.

ceramic matrix composites↗

Numerical Investigation of the Effect of Rolling on the Localized Stress and Strain Induction for Wire + Arc Additive Manufactured Structures

Cold rolling can be used in-process or post-process to improve microstructure, mechanical properties and residual stress in directed-energy-deposition techniques, such as the high deposition rate wire + arc additive manufacturing (WAAM) process. Finite element simulations of the rolling process are employed to investigate the effect of rolling parameters, in particular rolling load and roller profile radius on the residual stress field as well as plastic strain distribution for the profiled roller. The results show the response to rolling of commonly used structural metals in WAAM, i.e., AA2319, S335JR steel and Ti-6Al-4V, taking into account the presence of residual stresses. The rolling load leads to changes in the location and the maximum value of the compressive residual stresses, as well as the depth of the compressive residual stresses. However, the roller profile radius only changes the maximum value of these compressive residual stresses. Changing the rolling load influences the equivalent plastic strain close to the top surface of the wall as well as in deeper areas, whereas the influence of the roller profile radius is negligible. The plastic strain distribution is virtually unaffected by the initial residual stresses prior to rolling. Finally, design curves were generated from the simulations for different materials, suggesting ideal rolling load and roller profile combinations for microstructural improvement requiring certain plastic strains at a specific depth of the additive structure.

36 MATERIALS SCIENCE↗

Microstructure Generation via Generative Adversarial Network for Heterogeneous, Topologically Complex 3D Materials

Using a large-scale, experimentally captured 3D microstructure dataset, we implement the generative adversarial network (GAN) framework to learn and generate 3D microstructures of solid oxide fuel cell electrodes. The generated microstructures are visually, statistically, and topologically realistic, with distributions of microstructural parameters, including volume fraction, particle size, surface area, tortuosity, and triple phase boundary density, being highly similar to those of the original microstructure. These results are compared and contrasted with those from an established, grain-based generation algorithm (DREAM.3D). Importantly, simulations of electrochemical performance, using a locally resolved finite element model, demonstrate that the GAN generated microstructures closely match the performance distribution of the original, while DREAM.3D leads to significant differences. Finally, the ability of the generative machine learning model to recreate microstructures with high fidelity suggests that the essence of complex microstructures may be captured and represented in a compact and manipulatable form.

36 MATERIALS SCIENCE↗

On residual stress analysis and microstructural evolution for stainless steel type 304 spent nuclear fuel canisters weld joint: Numerical and experimental studies

Chloride-induced stress corrosion cracking (CISCC) in the weldments of austenitic stainless steel canisters is one of the primary safety concerns during the dry storage of used nuclear fuel at Independent Spent Fuel Storage Installations in coastal areas. In order to evaluate the CISCC behavior in the canister, a 3D sequentially coupled thermo-mechanical finite element model was built to simulate the residual stresses induced by two intersecting longitudinal and circumferential multi-pass welds in austenitic stainless steel mockup canister. Weld-induced residual stresses from simulation were in good agreement with the experimental measurement results by deep-hole drilling and contour methods. Through-wall high tensile axial and hoop stresses were observed in both the fusion zone and heat affected zone (HAZ) in the longitudinal and circumferential weld, respectively. On the other hand, the microstructure within the weldments of 304 stainless steel mockup was characterized using optical microscopy, scanning electron microscopy, electron back-scattered diffraction and energy dispersive X-ray spectroscopy methods. A few amount of MnS inclusions in both the base metal and HAZ, and a lot of (Mn,Si) x O y inclusions in the fusion zone were found. Meanwhile, there is some α'-martensite in the base metal, while the martensite was reversed in the HAZ. In the fusion zone, there is a lot of δ-ferrite. The martensite reversion phenomenon was also verified by the combination of Feritscope test and thermal simulation, which could predict a martensite reversion temperature as 400C°. The welding residual stresses and microstructure analysis results could offer the instructive information for the prediction of CISCC behavior of the spent nuclear fuel canisters.

36 MATERIALS SCIENCE↗

Multiscale mechanical behavior and microstructure evolution of extruded magnesium alloy sheets: Experimental and crystal plasticity analysis

Highlights: • Experimental stress-strain responses were reproduced by CPFE simulation based on Voronoi grains on three strain paths. • Textures predicted by simulation were in accordance with the ones measured by EBSD at the strain of 0.085. • Deformation heterogeneity in slip-dominated cases was found more significant than that in twin-favored case. • For slip-dominated cases, both high m′ value and high SFs in adjacent grains are responsible for strain localization. - Abstract: A phenomenological crystal plasticity finite element (CPFE) model based on Voronoi grains was applied to reproduce basic deformation features of a hot-extruded magnesium alloy sheet under various strain paths. Corresponding experimental investigations, including mechanical tests, electron back scattered diffraction (EBSD) measurements and optical observation, were also carried out as either a validation or a supplement of the numerical results. Predicted average stress-strain responses and texture evolution are in good accordance with measured ones. Furthermore, deformation heterogeneity at the mesoscopic and intergranular scale were investigated based on the proposed model. At the mesoscale, the heterogeneity in the slip-dominated cases tends to develop continuously, whereas the heterogeneity is retarded in twin-favored deformation. At the intergranular scale, it is concluded from the slip-dominated case that a high slip-transfer parameter and high Schmid factors (SFs) of principal slip systems in adjacent grains could accommodate higher local strain.

36 MATERIALS SCIENCE↗

Two-Magnon Relaxation Processes in Nanocrystalline Thin Magnetic Films

Numerical analysis of the micromagnetic model was used to reveal the ‘resonance’ feature of relaxation processes in nanocrystalline thin magnetic films. This feature manifests itself in the form of sharp broadening of the ferromagnetic resonance (FMR) line at a certain frequency f{sub 1} depending on magnetic characteristics of the film, and is observed only in films the thickness of which exceeds some threshold value d{sub min}. Sharp broadening of the FMR line is accompanied by significant shift of the resonance field, whereas the shift value changes the sign at frequency ~ f{sub 1}. It was shown analytically that the nature of observed effects is associated with the two-magnon process of spin waves scattering on quasi-periodic magnetic microstructure – magnetization ‘ripple’. Obtained expressions for the threshold value of film thickness d{sub min} and frequency of maximum broadening of FMR line f{sub 1} agree well with the results of numerical computation of micromagnetic model.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Finite Element Simulation and Optimization of Gas-Quenching Process for Tool Steels

Various gas-quenching processes, including marquenching, were investigated to optimize gas-quenching processes in terms of distortion and hardness by means of numerical and experimental analyses. The temperature, microstructure, hardness, and distortion during the various gas-quenching processes of a tool steel block were simulated using a finite element method based on a coupled thermo-metallurgical–mechanical model. The predicted temperature, hardness, and distortion agreed well with the experimental data. The tool steel block (200 × 150 × 70 mm{sup 3}) quenched under 10 bar pressure of nitrogen gas (Case 2) had higher hardness due to the higher martensite fraction and larger distortion owing to the higher thermal stress induced by faster cooling, compared to the block quenched under 2 bar pressure of nitrogen gas (Case 1). The tool steel block marquenched under 10 bar pressure of nitrogen gas interrupted by isothermal holding at 500 °C (Case 3) had 30% smaller distortion with a negligible loss of hardness compared to Case 2. Furthermore, the simulation results could provide an optimized process condition to minimize distortion of the gas-quenched tool steel block while satisfying the hardness requirement.

36 MATERIALS SCIENCE↗

Interpreting Electrochemical and Chemical Sodiation Mechanisms and Kinetics in Tin Antimony Battery Anodes Using in Situ Transmission Electron Microscopy and Computational Methods

Intermetallic compounds such as SnSb are promising anode materials for sodium ion batteries; however, their nanoscale sodiation mechanisms are not well understood. Here, we used a combination of in situ transmission electron microscopy (TEM), first-principles electronic structure calculations, computational thermodynamic modeling, and phase-field simulations to reveal the sodiation mechanisms and to quantify microstructural effects contributing to the underlying reaction kinetics in SnSb electrodes. During in situ sodiation experiments, the nanocrystalline SnSb thin films underwent a rapid amorphous phase transformation upon sodiation, as determined by in situ TEM and electron diffraction experiments. The Na + diffusion coefficients were measured with and without an external electrical bias, and the data showed that an applied potential increased Na + diffusion by an order of magnitude compared to solid-state diffusion. Furthermore, there was a distinct decrease in sodium diffusion upon the formation of the amorphous phase that resulted from a change in the local structure and grain boundaries. To further understand how the Na + transport mechanism correlated with the changes observed in the SnSb thin films, phase-field modeling was used, which considered sodium diffusion within the grain boundaries together with their evolution and stress–strain state. As a result, these findings enhance our understanding of sodiation mechanisms within intermetallic anode materials for sodium ion battery applications.

25 ENERGY STORAGE↗

Application of chord length distributions and principal component analysis for quantification and representation of diverse polycrystalline microstructures

Highlights: • Microstructure quantification based on directional chord length distribution and principal component analysis is presented • A boundary-based algorithm of calculations of chord length distributions is introduced • Utility of the quantification framework is shown in three case studies on synthetic, experimental, and simulation datasets • Angularly resolved chord length distribution captures essential details of grain size and shape in diverse microstructures • Low-dimensional representations of directional chord length distributions are obtained using principal component analysis - Abstract: Quantification of mesoscale microstructures of polycrystalline materials is important for a range of practical tasks of materials design and development. The current protocols of quantifying grain size and morphology often rely on microstructure metrics (e.g., mean grain diameter) that overlook important details of the mesostructure. In this work, we present a quantification framework based on directionally resolved chord length distribution and principal component analysis as a means of extracting additional information from 2-D microstructural maps. Towards this end, we first present in detail a method for calculating chord length distribution based on boundary segments available in modern digital datasets (e.g., from microscopy post-processing) and their low-rank representations by principal component analysis. The utility of the proposed framework for capturing grain size, morphology, and their anisotropy for efficient visualization, representation, and specification of polycrystalline microstructures is then demonstrated in case studies on datasets from synthetic generation, experiments (on Ni-base superalloys), and simulations (on steel during recrystallization).

36 MATERIALS SCIENCE↗

Microstructural characterization and assessment of mechanical properties of concrete based on combined elemental analysis techniques and Fast-Fourier transform-based simulations

This paper presents a pixel-based modeling approach of concrete which combines an experimental characterization of concrete and the Fast-Fourier transform simulations. High-resolution phase maps created from experimental characterization by micro X-ray fluorescence, energy dispersive X-ray analysis, and X-ray diffraction contain 9 different phases, including 22.17 vol.% of hydrated cement paste, 54.21 vol.% of minerals, and 23.62 vol.% of interfaces. These phases provide the input for determining the effective elastic properties, coupled with Fast-Fourier transform-based simulation. The simulation results show that the effective range of Young’s modulus of concrete is comparable with the range of experimental values ~ 37 ± 4 GPa with the assumption of realistic properties of interfaces.

36 MATERIALS SCIENCE↗

Modeling Of Microstructure Evolution Of BCC Metals Subjected To Severe Plastic Deformation

Prediction of microstructure evolution and properties of ultrafine-grained materials is one of the most significant, current problems in materials science. Several advanced methods of analysis can be applied for this issue: vertex models, phase field models, Monte Carlo Potts, finite element method (FEM) discrete element method (DEM) and finally cellular automata (CA). The main asset of the CA is ability for a close correlation of the microstructure with the mechanical properties in micro- and meso-scale simulation. Joining CA with the DEM undoubtedly improves accuracy of modeling of coupled phenomena during the innovative forming processes in both micro- and macro-scale. Deformation in micro-scale shows anisotropy, which connected with that the polycrystalline material contains grains with different crystallographic orientation, and grain deformation is depended from configuration of directions of main stresses and axis of grain. Then, CA and DEM must be joint solutions of crystal plasticity theory. In the present model, deformation in macro-scale is transferred to meso-sale, where a block contains several, score or hundreds grains, and then is applied in micro-scale to each grain. Creation of low-angle boundaries and their development into high-angle boundaries are simulated by the cellular automata on the base of calculations using finite element method and crystal plasticity theory. The idea proposed in this study and particular solutions are discussed for the case of ultrafine-grained low-carbon steel.

36 MATERIALS SCIENCE↗

A coupled fluid-mechanical workflow to simulate the directed energy deposition additive manufacturing process

Simulation of additive manufacturing processes can provide essential insight into material behavior, residual stress, and ultimately, the performance of additively manufactured parts. In this work, we describe a new simulation based workflow utilizing both solid mechanics and fluid mechanics based formulations within the finite element software package SIERRA (Sierra Solid Mechanics Team in Sierra/Solid Mechanics 4.52 User’s Guide SAND2019-2715. Technical report, Sandia National Laboratories, 2011) to enable integrated simulations of directed energy deposition (DED) additive manufacturing processes. In this methodology, a high-fidelity fluid mechanics based model of additive manufacturing is employed as the first step in a simulation workflow. This fluid model uses a level set field to track the location of the boundary between the solid material and background gas and precisely predicts temperatures and material deposition shapes from additive manufacturing process parameters. Next, the resulting deposition shape and temperature field from the fluid model are then mapped into a solid mechanics formulation to provide a more accurate surface topology for radiation and convection boundary conditions and a prescribed temperature field. Solid mechanics simulations are then conducted to predict the evolution of material stresses and microstructure within a part. By combining thermal history and deposition shape from fluid mechanics with residual stress and material property evolutions from solid mechanics, additional fidelity and precision are incorporated into additive manufacturing process simulations providing new insight into complex DED builds.

36 MATERIALS SCIENCE↗