Search NASA⌕ Search

SEARCH · Search NASA

Results for “parameter selection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Development and Application of Benchmark Examples for Mode II Static Delamination Propagation and Fatigue Growth Predictions

The development of benchmark examples for static delamination propagation and cyclic delamination onset and growth prediction is presented and demonstrated for a commercial code. The example is based on a finite element model of an End-Notched Flexure (ENF) specimen. The example is independent of the analysis software used and allows the assessment of the automated delamination propagation, onset and growth prediction capabilities in commercial finite element codes based on the virtual crack closure technique (VCCT). First, static benchmark examples were created for the specimen. Second, based on the static results, benchmark examples for cyclic delamination growth were created. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Fourth, starting from an initially straight front, the delamination was allowed to grow under cyclic loading. The number of cycles to delamination onset and the number of cycles during delamination growth for each growth increment were obtained from the automated analysis and compared to the benchmark examples. Again, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. The benchmarking procedure proved valuable by highlighting the issues associated with choosing the input parameters of the particular implementation. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Overall the results are encouraging, but further assessment for mixed-mode delamination is required.

Krueger, Ronald↗

Development of Benchmark Examples for Quasi-Static Delamination Propagation and Fatigue Growth Predictions

The development of benchmark examples for quasi-static delamination propagation and cyclic delamination onset and growth prediction is presented and demonstrated for Abaqus/Standard. The example is based on a finite element model of a Double-Cantilever Beam specimen. The example is independent of the analysis software used and allows the assessment of the automated delamination propagation, onset and growth prediction capabilities in commercial finite element codes based on the virtual crack closure technique (VCCT). First, a quasi-static benchmark example was created for the specimen. Second, based on the static results, benchmark examples for cyclic delamination growth were created. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Fourth, starting from an initially straight front, the delamination was allowed to grow under cyclic loading. The number of cycles to delamination onset and the number of cycles during delamination growth for each growth increment were obtained from the automated analysis and compared to the benchmark examples. Again, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. The benchmarking procedure proved valuable by highlighting the issues associated with choosing the input parameters of the particular implementation. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Overall the results are encouraging, but further assessment for mixed-mode delamination is required.

Krueger, Ronald↗

Development of Benchmark Examples for Static Delamination Propagation and Fatigue Growth Predictions

The development of benchmark examples for static delamination propagation and cyclic delamination onset and growth prediction is presented and demonstrated for a commercial code. The example is based on a finite element model of an End-Notched Flexure (ENF) specimen. The example is independent of the analysis software used and allows the assessment of the automated delamination propagation, onset and growth prediction capabilities in commercial finite element codes based on the virtual crack closure technique (VCCT). First, static benchmark examples were created for the specimen. Second, based on the static results, benchmark examples for cyclic delamination growth were created. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Fourth, starting from an initially straight front, the delamination was allowed to grow under cyclic loading. The number of cycles to delamination onset and the number of cycles during stable delamination growth for each growth increment were obtained from the automated analysis and compared to the benchmark examples. Again, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. The benchmarking procedure proved valuable by highlighting the issues associated with the input parameters of the particular implementation. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Overall, the results are encouraging but further assessment for mixed-mode delamination is required.

Kruger, Ronald↗

RAY-UI: A powerful and extensible user interface for RAY

The RAY-UI project started as a proof-of-concept for an interactive and graphical user interface (UI) for the well-known ray tracing software RAY [1]. In the meantime, it has evolved into a powerful enhanced version of RAY that will serve as the platform for future development and improvement of associated tools. The software as of today supports nearly all sophisticated simulation features of RAY. Furthermore, it delivers very significant usability and work efficiency improvements. Beamline elements can be quickly added or removed in the interactive sequence view. Parameters of any selected element can be accessed directly and in arbitrary order. With a single click, parameter changes can be tested and new simulation results can be obtained. All analysis results can be explored interactively right after ray tracing by means of powerful integrated image viewing and graphing tools. Unlimited image planes can be positioned anywhere in the beamline, and bundles of image planes can be created for moving the plane along the beam to identify the focus position with live updates of the simulated results. In addition to showing the features and workflow of RAY-UI, we will give an overview of the underlying software architecture as well as examples for use and an outlook for future developments.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Evaluating a Historical Airborne Release Test with Modern Modeling Methods

Safety analysts throughout the U.S. Department of Energy (DOE) complex rely on the data provided in the DOE Handbook, DOE-HDBK-3010, to determine source terms that may be incorporated into the document safety analyses. Most often, analysts simply take the bounding values due to time constraints or simply to bound calculations. This is a safe approach that helps avoid regulatory critique; however, it may not provide results that are meaningful or relevant to the conditions being evaluated. The derivation of the data, such as airborne release fractions (ARFs) and respirable fractions (RFs) in the Handbook often depend on very limited table-top and bench/laboratory experiments, as well as engineering judgment which may not be well substantiated, and may not be representative of the actual situation. One historical dataset included a test where a solid contaminant was sprinkled over a liquid gasoline pool and set on fire (also referred to as Mishima and Schwendiman's test later in this paper). The airborne release was measured over the duration of the burn, but then collected separately for a time after the burning was completed. It can be assumed that the collected contaminant in the latter period corresponds to re-suspended particles, whereas the earlier period collected contaminant includes a combination of directly released as well as early released re-suspended particles. This scenario was recently modeled using SIERRA/Fuego as part of a parametric sensitivity study, however there were some shortcomings of the analysis methods. First, the code at the time lacked a multi-component particle evaporation model, which is necessary to capture the particle size effect of liquid/solid particles that can dynamically evaporate the liquid component. Second, a particle sticking and resuspension model did not exist at the time of the study. Recent model implementation now permits the study be repeated with the improved physical models. In the earlier work, four potential mechanisms were considered to potentially contribute to the release of the particles. These were: 1. Evaporation Induced Entrainment (EIE); 2. Surface Agitation by Wind; 3. Surface Agitation by Boiling; 4. Residue Entrainment (Resuspension). The sensitivity study evaluated mechanism 1 and 3 in the above list. Parameters varied were selected to be a reflection of a practical range of test conditions. The varied parameters included the boiling duration, fuel height, injected mass, particle size, turbulence intensity, and initial particle height. The boiling duration was the most significant parameter. The most significant mechanism was no.3, Surface Agitation by Boiling. This paper reports the implementation of the new multi-component evaporation model and its effect on the findings from the previous effort. The Mishima and Schwendiman test was re-modeled with the new evaporation model, and the results of the re-evaluation are presented. (authors)

07 ISOTOPE AND RADIATION SOURCES↗

Selective factors in sun-weather research

Research on the correlations between solar wind/IMF disturbances and subsequent winter troposphere vorticity changes (denoted SV) are reviewed to investigate sun-weather relationships. Uncertainties in the research attempting to link short-term solar variations and associated changes in the lower atmosphere are discussed, and it is noted that such analyses have generally not addressed either the choice of parameters or the selective factors involved in the physical relationships existing between parameters. It is suggested that the identification of a viable mechanism scenario would require a detailed multiparameter selective factor analysis, extending to the investigation of the atmospheric data as well as the solar wind/IMF parameters.

Taylor, H. A., Jr.↗

Task-based detectability in CT image reconstruction by filtered backprojection and penalized likelihood estimation

Purpose: Nonstationarity is an important aspect of imaging performance in CT and cone-beam CT (CBCT), especially for systems employing iterative reconstruction. This work presents a theoretical framework for both filtered-backprojection (FBP) and penalized-likelihood (PL) reconstruction that includes explicit descriptions of nonstationary noise, spatial resolution, and task-based detectability index. Potential utility of the model was demonstrated in the optimal selection of regularization parameters in PL reconstruction. Methods: Analytical models for local modulation transfer function (MTF) and noise-power spectrum (NPS) were investigated for both FBP and PL reconstruction, including explicit dependence on the object and spatial location. For FBP, a cascaded systems analysis framework was adapted to account for nonstationarity by separately calculating fluence and system gains for each ray passing through any given voxel. For PL, the point-spread function and covariance were derived using the implicit function theorem and first-order Taylor expansion according toFessler [“Mean and variance of implicitly defined biased estimators (such as penalized maximum likelihood): Applications to tomography,” IEEE Trans. Image Process. 5(3), 493–506 (1996)]. Detectability index was calculated for a variety of simple tasks. The model for PL was used in selecting the regularization strength parameter to optimize task-based performance, with both a constant and a spatially varying regularization map. Results: Theoretical models of FBP and PL were validated in 2D simulated fan-beam data and found to yield accurate predictions of local MTF and NPS as a function of the object and the spatial location. The NPS for both FBP and PL exhibit similar anisotropic nature depending on the pathlength (and therefore, the object and spatial location within the object) traversed by each ray, with the PL NPS experiencing greater smoothing along directions with higher noise. The MTF of FBP is isotropic and independent of location to a first order approximation, whereas the MTF of PL is anisotropic in a manner complementary to the NPS. Task-based detectability demonstrates dependence on the task, object, spatial location, and smoothing parameters. A spatially varying regularization “map” designed from locally optimal regularization can improve overall detectability beyond that achievable with the commonly used constant regularization parameter. Conclusions: Analytical models for task-based FBP and PL reconstruction are predictive of nonstationary noise and resolution characteristics, providing a valuable framework for understanding and optimizing system performance in CT and CBCT.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Quantiles, parametric-select density estimation, and bi-information parameter estimators

A quantile-based approach to statistical analysis and probability modeling of data is presented which formulates statistical inference problems as functional inference problems in which the parameters to be estimated are density functions. Density estimators can be non-parametric (computed independently of model identified) or parametric-select (approximated by finite parametric models that can provide standard models whose fit can be tested). Exponential models and autoregressive models are approximating densities which can be justified as maximum entropy for respectively the entropy of a probability density and the entropy of a quantile density. Applications of these ideas are outlined to the problems of modeling: (1) univariate data; (2) bivariate data and tests for independence; and (3) two samples and likelihood ratios. It is proposed that bi-information estimation of a density function can be developed by analogy to the problem of identification of regression models.

Parzen, E.↗

Relative phase interactions of two copropagating laser beams in underdense plasmas at different intensities and spot sizes

The mutual interactions of two copropagating laser beams at a relative phase are studied using a two-dimensional fluid code. The interactions are investigated in underdense plasma at selected beam configurations and beam parameters for two separate nonlinearities, i.e., the ponderomotive and the relativistic nonlinearity. The selected beam configurations are introduced by different initial transverse spot size perturbations (finite and infinite) and different initial transversal intensity distributions (nonuniform and uniform) over those spot sizes and the selected beam parameters are given by different initial beam intensities relevant to each nonlinearity. In the ponderomotive nonlinearity, simulation results show that no mutual interactions are demonstrated between the copropagating beams regardless of the initial beam configurations and parameters. In nonlinear relativistic simulations, the mutual interactions between the beams are clearly observed, a mutual repulsion is formed in the presence of initial intensities that are nonuniformly distributed over finite spot sizes, and an effective strongly modulated mutual attraction takes places in the presence of initial intensities that are uniformly distributed over infinite spot sizes. Moreover, it is found in these simulations that increasing the initial beam intensities improves the attraction properties between the copropagationg beams.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Oscillation Detection Algorithm Development Summary Report and Test Plan

Small signal stability problems are one of the major threats to grid stability and reliability in California and the western U.S. power grid. An unstable oscillatory mode can cause large-amplitude oscillations and may result in system breakup and large-scale blackouts. There have been several incidents of system-wide oscillations. Of them, the most notable is the August 10, 1996 western system breakup produced as a result of undamped system-wide oscillations. There is a great need for real-time monitoring of small-signal oscillations in the system. In power systems, a small-signal oscillation is the result of poor electromechanical damping. Considerable understanding and literature have been developed on the small-signal stability problem over the past 50+ years. These studies have been mainly based on a linearized system model and eigenvalue analysis of its characteristic matrix. However, its practical feasibility is greatly limited as power system models have been found inadequate in describing real-time operating conditions. Significant efforts have been devoted to monitoring system oscillatory behaviors from real-time measurements in the past 20 years. The deployment of phasor measurement units (PMU) provides high-precision time-synchronized data needed for estimating oscillation modes. Measurement-based modal analysis, also known as ModeMeter, uses real-time phasor measure-ments to estimate system oscillation modes and their damping. Low damping indicates potential system stability issues. Oscillation alarms can be issued when the power system is lightly damped. A good oscillation alarm tool can provide time for operators to take remedial reaction and reduce the probability of a system breakup as a result of a light damping condition. Real-time oscillation monitoring requires ModeMeter algorithms to have the capability to work with various kinds of measurements: disturbance data (ringdown signals), noise probing data, and ambient data. Several measurement-based modal analysis algorithms have been developed. They include Prony analysis, Regularized Ro-bust Recursive Least Square (R3LS) algorithm, Yule-Walker algorithm, Yule-Walker Spectrum algorithm, and the N4SID algo-rithm. Each has been shown to be effective for certain situations, but not as effective for some other situations. For example, the traditional Prony analysis works well for disturbance data but not for ambient data, while Yule-Walker is designed for ambient data only. Even in an algorithm that works for both disturbance data and ambient data, such as R3LS, latency results from the time window used in the algorithm is an issue in timely estimation of oscillation modes. For ambient data, the time window needs to be longer to accumulate information for a reasonably accurate estimation; while for disturbance data, the time window can be significantly shorter so the latency in estimation can be much less. In addition, adding a known input signal such as noise probing signals can increase the knowledge of system oscillatory properties and thus improve the quality of mode estimation. System situations change over time. Disturbances can occur at any time, and probing signals can be added for a certain time period and then removed. All these observations point to the need to add intelligence to ModeMeter applications. That is, a ModeMeter needs to adaptively select different algorithms and adjust parameters for various situations. This project aims to develop systematic approaches for algorithm selection and parameter adjustment. The very first step is to detect occurrence of oscillations so the algorithm and parameters can be changed accordingly. The proposed oscillation detection approach is based on the signal-noise ratio of measurements.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Selective Biosorption of Valuable Rare Earth Elements Among Co-Occurring Lanthanides

To meet the increasing demand for rare earth elements (REEs) essential for low carbon-intensity energy technologies, new methods are needed for selective REE extraction from unconventional resources. Only a few REEs have significant economic value, but isolation of target rare earths from co-occurring lanthanides is challenging due to their similar chemical behavior. We present a novel approach to enhance separation of specific REEs from lanthanide mixtures. Escherichia coli cells engineered with lanthanide binding tags (LBTs) were immobilized in nonadsorbing, permeable polyethylene glycol diacrylate beads and packed into continuous flow, fixed-bed columns. Breakthrough of 15 rare earths in the +3 oxidation state resulted in notable differences in adsorption selectivity, with greatest separation between europium (Eu) and lanthanum (La) due to competitive displacement. REE adsorption onto fixed-bed columns was predicted by coupling a surface complexation model to a calibrated one-dimensional dual porosity transport model that accounts for interbead advective and intrabead diffusive transport. A tradeoff between high-abundance, low-affinity native carboxyl sites and low-abundance, high-affinity engineered LBT sites dictates process recovery efficiency and selectivity. Key chemical and operational parameters are identified to maximize selective extraction of high-value lanthanides, achieving a threefold enhancement of Eu recovery relative to La in a mixed REE solution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

TEM study of the FSW nugget in AA2195-T81

During fiiction stir welding (FSW) the material being joined is subjected to a thermal- mechanical process in which the temperature, strain and strain rates are not completely understood. To produce a defect fiee weld, process parameters for the weld and tool pin design must be chosen carefully. The ability to select the weld parameters based on the thermal processing requirements of the material, would allow optimization of mechanical properties in the weld region. In this study, an attempt is made to correlate the microstructure with the variation in thermal history the material experiences during the FSW process.

Schneider, J. A.↗

Additive Manufacturing Process Development DOE for NASA HR-1 using Laser Blown Powder Directed Energy Deposition

NASA HR-1 is a Fe-Ni-Cr alloy that is used for high pressure hydrogen applications such as rocket engines, energy, and oil and gas. This investigation was focused on conducting a design of experiment program aimed at mapping the parameter process window for NASA HR-1 using the laser blown powder directed energy deposition (LP-DED) process. A two phased design of experiments (DOE), the first phase of the experiment was focused on optimizing single bead tracks while the second phase of the experiment was focused on optimizing bead overlap hatching in a multi pass bead build up. During the first phase of the deposition parameters, namely laser power, travel speed, and powder feed rate were varied. A down selection from the single bead parameter set was made and hatching experiments were conducted that focused on the overlap distance. In this paper the approach for conducting the DOE and results are discussed. The results focused on measurement of bead geometry, the as-built microstructural evolution, and porosity within the samples. The team at MSFC saw a variety of results across the process map created during the first phase of experimentation and were able to down select a parameter that created an optimal bead shape with a minimal amount of build porosity. It was determined that laser power and robot travel speed were the most sensitive parameters. The results from this investigation will inform future laser powder directed energy deposition parameter developments.

Parker Shake↗

The Application of an Evolutionary Programming Process to a Simulation of the ETEX Large-Scale Airborne Dispersion Experiment

Abstract Airborne tracer simulations are typically performed using a dispersion model driven by a high-resolution meteorological model. Besides solving the dynamic equations of momentum, heat, and moisture on the resolved model grid, mesoscale models must account for subgrid-scale fluxes and other unresolved processes. These are estimated through parameterization schemes of eddy diffusion, convection, and surface interactions, and they make use of prescribed parameters set by the user. Such “free” model parameters are often poorly constrained, and a range of plausible values exists for each. Evolutionary programming (EP) is a process to improve the selection of the parameters. A population of simulations is first run with a different set of parameter values for each member, and the member judged most accurate is selected as the “parent” of a new “generation.” After a number of iterations, the simulations should approach a configuration that is best adapted to the atmospheric conditions. We apply the EP process to simulate the first release of the 1994 European Tracer Experiment (ETEX) project, which comprised two experiments in which a tracer was released in western France and sampled by an observing network. The EP process is used to improve a simulation of the RAMS mesoscale weather model, with weather data collected during ETEX being used to “score” the individual members according to how well each simulation matches the observations. The meteorological simulations from before and after application of the EP process are each used to force a dispersion model to create a simulation of the ETEX release, and substantial improvement is observed when these are validated against sampled tracer concentrations.

54 ENVIRONMENTAL SCIENCES↗

The Dissolution of Fe in HCl from the Ilmenite Concentrate; Evaluating the Effect of Operating Parameters and Mutual Interactions

Selective HCl dissolution of ilmenite components for obtaining Ti or titanium dioxide (TiO{sub 2}) has been highly recognized due to its advantages, greater environmental friendliness, and simplicity, compared to H{sub 2}SO{sub 4} and Cl{sub 2} methods. The effect of numerous parameters has been studied with the one-factor-at-a-time method. The present study aimed to evaluate the effect of key operation parameters, such as acid-to-solid ratio (A/S: 5 to 20 mL/g), reaction temperature (T: 70 °C to 100 °C), and acid concentration (A pct: 15 to 30 wt pct), on the dissolution of Fe in HCl solution with the minimum Ti losses to the leachate from its abundant, domestic, and low-cost mineral source (Kahnooj ilmenite concentrate) using central composite design–response surface methodology. After 90 minutes of leaching, the Ti/Fe (pct) in terms of dissolved amounts was selected as the process assessment response function. Based on the conducted experimental and statistical analysis, increasing the levels of parameters in the studied domain leads to an increase in Ti/Fe (pct), in the order of A pct > T > A/S. Two statistically significant mutual interactions between A/S-T and T-A pct, with 95 pct confidence level, were revealed for the first time in this study. The optimization strategy was set to the minimization of Ti/Fe (pct) by considering the objective of study and the selected response function. The A/S, T, and A pct were determined to be 5 mL/g, 70 °C, and 15 pct, respectively, for maximum impurity dissolution and minimum Ti loss to the leachate.

36 MATERIALS SCIENCE↗

Tune-stabilized, non-scaling, fixed-field, alternating gradient accelerator

A FFAG is a particle accelerator having turning magnets with a linear field gradient for confinement and a large edge angle to compensate for acceleration. FODO cells contain focus magnets and defocus magnets that are specified by a number of parameters. A set of seven equations, called the FFAG equations relate the parameters to one another. A set of constraints, call the FFAG constraints, constrain the FFAG equations. Selecting a few parameters, such as injection momentum, extraction momentum, and drift distance reduces the number of unknown parameters to seven. Seven equations with seven unknowns can be solved to yield the values for all the parameters and to thereby fully specify a FFAG.

43 PARTICLE ACCELERATORS↗

Thermal Behavior Study of the MoVTeNb Oxide Catalyst for Selective Oxidation Process

Several parameters involved in preparing the multi metal oxide (MMO) catalysts (Mo{sub 1}V{sub 0.3}Te{sub 0.23}Nb{sub 0.12}O{sub x}) for selective oxidation of propane to acrylic acid (AA) were investigated. These included the proper pre-calcined and calcinations atmosphere effect on the performance of the catalysts. It was found that each metal element plays a critical role to the performance of an effective catalyst and also the calcinations under a non-flow inert atmosphere. The characterization results from XRD, SEM, TG and DSC show the important differences depending on the activation procedures of the MoVTeNb oxide catalyst. The XRD analysis is used to identify the phase inventory of the MoVTeNb oxide catalysts. The structure of orthorhombic M1, M2, TeMo{sub 5}O{sub 16}, V{sub 0.95}Mo{sub 0.97}O{sub 5} and Mo{sub 5}O{sub 14} phase was investigated. The orthorhombic M1 phase is the most active and selective phase and is responsible for the major of the efficiently of the best catalyst for selective oxidation process. TGA and DTG allow the identification of the number and types, of reactions involving evaporation of small molecules from removal of ligands and water to condensation or drying processes. From all these analyses it was proven that the activation procedures would affect the performance of the MoVTeNb oxide catalyst.

36 MATERIALS SCIENCE↗

Generation-based Evolutionary Tool for the Optimization of Constellations (GenETOC)

With the rapid growth in the capabilities of smaller satellites, satellite architectures that replace a single, extremely capable spacecraft with multiple, cheaper ones are gaining in popularity. Unfortunately, the orbit design process for constellations can be significantly more involved, especiallywhen the relative placement of the individual spacecraft within the constellation is not constrained by mission and/or science objectives. Optimizing a satellite constellation in the presence of multiple, competing objectives is a highly complex problem to which many traditional mathematical optimization methods cannot be applied and few tools exist to help mission designers search for promising candidate mission designs. The Generation-based Evolutionary Tool for the Optimization of Constellations (GenETOC) has been created to search for near-optimal constellation design options. GenETOC combines a modified version of the Non-dominated Sorting Genetic Algorithm II (NSGA II) with STK Components libraries (a 3rdparty .NET package created by Analytical Graphics Inc.) to create a framework that enables a mission designer to generate a simulation that models the design problem and obtain a family of potential, near-optimal solutions that can be investigated more in detail. GenETOC was developed in C# using the .NET framework with Windows Presentation Foundation (WPF) serving as the framework from which to create the graphical user interface (GUI). GenETOC user inputs can be categorized into three major data components: definition of the problem (areas of interest, satellite decision parameters, and sensor configurations), definition of performance objectives, and specification of the genetic algorithm (GA) parameters. In the problem definition component, the user is prompted to define the areas of interest against which the performance metrics will be computed, define the sensor parameters and attach them to specific spacecraft, select which satellite orbital parameters will be added to the decision space of the GA, and specify the range of desired values for each optimization parameter. For performance objectives, the user is presented with a list of available coverage and revisit performance based calculation options from which two metrics are chosen to serve as the objective functions that the GA will use to evaluate solutions during the optimization process. Finally, the definition of the GA parameters provides user control over the number of generations (number of optimization iterations), the population size (number of candidate constellations created in each generation), and the adaptive mutation and crossover threshold values (control parameters for how frequently each process occurs during the optimization). GenETOC has been extensively tested to verify the individual components of the optimization process. The GA has been tested against a suite of GA test problems to confirm convergence to the known two and three-dimensional Pareto fronts. The coverage and revisit performance metrics obtained in GenETOC are compared with STK desktop scenarios, confirming the constellations are being appropriately modeled within GenETOC simulations. A walkthrough of a simple, example problem is provided to illustrate the workings of GenETOC and to demonstrate the output available to the mission designer.

mission design↗