Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface morphologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Nucleation and growth of ZnO on PMMA by low-temperature atomic layer deposition

ZnO films were grown by atomic layer deposition at 35 °C on poly(methyl methacrylate) substrates using diethylzinc and water precursors. The film growth, morphology, and crystallinity were studied using Rutherford backscattering spectrometry, time-of-flight elastic recoil detection analysis, atomic force microscopy, scanning electron microscopy, and x-ray diffraction. The uniform film growth was reached after several hundreds of deposition cycles, preceded by the precursor penetration into the porous bulk and island-type growth. After the full surface coverage, the ZnO films were stoichiometric, and consisted of large grains (diameter 30 nm) with a film surface roughness up to 6 nm (RMS). The introduction of Al{sub 2}O{sub 3} seed layer enhanced the initial ZnO growth substantially and changed the surface morphology as well as the crystallinity of the deposited ZnO films. Furthermore, the water contact angles of the ZnO films were measured, and upon ultraviolet illumination, the ZnO films on all the substrates became hydrophilic, independent of the film crystallinity.

36 MATERIALS SCIENCE↗

Effect of defects on reaction of NiO surface with Pb-contained solution

In order to understand the role of defects in chemical reactions, we used two types of samples, which are molecular beam epitaxy (MBE) grown NiO(001) film on Mg(001) substrate as the defect free NiO prototype and NiO grown on Ni(110) single crystal as the one with defects. In-situ observations for oxide-liquid interfacial structure and surface morphology were performed for both samples in water and Pb-contained solution using high-resolution X-ray reflectivity and atomic force microscopy. For the MBE grown NiO, no significant changes were detected in the high-resolution X-ray reflectivity data with monotonic increase in roughness. Meanwhile, in the case of native grown NiO on Ni(110), significant changes in both the morphology and atomistic structure at the interface were observed when immersed in water and Pb-contained solution. Our results provide simple and direct experimental evidence of the role of the defects in chemical reaction of oxide surfaces with both water and Pb-contained solution.

Kim, Jongjin↗

Plasmonic formation mechanism of periodic 100-nm-structures upon femtosecond laser irradiation of silicon in water

The formation of laser-induced periodic surface structures (LIPSS) upon irradiation of silicon by multiple (N = 100) linearly polarized Ti:sapphire femtosecond laser pulses (duration τ = 30 fs, center wavelength λ{sub 0} ∼ 790 nm) is studied experimentally in air and water environment. The LIPSS surface morphologies are characterized by scanning electron microscopy and their spatial periods are quantified by two-dimensional Fourier analyses. It is demonstrated that the irradiation environment significantly influences the periodicity of the LIPSS. In air, so-called low-spatial frequency LIPSS (LSFL) were found with periods somewhat smaller than the laser wavelength (Λ{sub LSFL} ∼ 0.7 × λ{sub 0}) and an orientation perpendicular to the laser polarization. In contrast, for laser processing in water a reduced ablation threshold and LIPSS with approximately five times smaller periods Λ{sub LIPSS} ∼ 0.15 × λ{sub 0} were observed in the same direction as in air. The results are discussed within the frame of recent LIPSS theories and complemented by a thin film based surface plasmon polariton model, which successfully describes the tremendously reduced LIPSS periods in water.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Imaging Catalytic Activation of CO 2 on Cu 2 O (110): A First-Principles Study

Balancing global energy needs against increasing greenhouse gas emissions requires new methods for efficient CO 2 reduction. While photoreduction of CO 2 is a viable approach for fuel generation, the rational design of photocatalysts hinges on precise characterization of the surface catalytic reactions. Cu 2 O is a promising next-generation photocatalyst, but the atomic-scale description of the interaction between CO 2 and the Cu 2 O surface is largely unknown, and detailed experimental measurements are lacking. In this study, density-functional-theory (DFT) calculations have been performed to identify the Cu 2 O (110) surface stoichiometry that favors CO 2 reduction. To facilitate interpretation of scanning tunneling microscopy (STM) and X-ray absorption near-edge structures (XANES) measurements, which are useful for characterizing catalytic reactions, we present simulations based on DFT-derived surface morphologies with various adsorbate types. STM and XANES simulations were performed using the Tersoff Hamann approximation and Bethe-Salpeter equation (BSE) approach, respectively. The results provide guidance for observation of CO 2 reduction reaction on, and rational surface engineering of, Cu 2 O (110). In conclusion, they also demonstrate the effectiveness of computational image and spectroscopy modeling as a predictive tool for surface catalysis characterization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Benefits of homoepitaxy on the properties of nonpolar (Zn,Mg)O/ZnO quantum wells on a-plane ZnO substrates

We report on the properties of nonpolar (Zn,Mg)O/ZnO quantum wells (QW) homoepitaxially grown by molecular beam epitaxy on a-plane ZnO substrates. We demonstrate a drastic improvement of the structural properties. We compare the photoluminescence properties of nonpolar homoepitaxial QWs and nonpolar heteroepitaxial QWs grown on sapphire and show that the reduction in structural defects and the improvement of surface morphology are correlated with a strong enhancement of the photoluminescence properties: reduction in full width at half maximum, strong increase in the luminescence intensities and their thermal stability. The comparison convincingly demonstrates the interest of homoepitaxial nonpolar QWs for bright UV emission applications.

36 MATERIALS SCIENCE↗

Corrosion of Chromia-Forming and Alumina-Forming Ferritic Stainless Steels under Dual Atmosphere Exposure Conditions

The surface morphology and chemistry of oxide scales formed on select chromia-forming and alumina-forming ferritic steels have been studied after exposure to a dual atmosphere of hydrogen and air. Localized Fe-rich oxide nodules with surface whiskers/platelets form at the onset of corrosion. The initiation and growth of localized nodules and breakdown of passivation are attributed to the presence of hydrogen, inclusion of iron oxide in the passivating scale, and subsequent growth of iron-rich oxide due to the establishment of redox (H 2 -H 2 O) atmosphere and modification of oxide defect chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of Carbon Nanotube Concentration on the Corrosion Behavior of Electroless Ni-B-CNT Coating

In this study, Ni-B-CNT composite was deposited on AISI 4140 steel using different concentrations of CNTs ranging from 0.2 to 1 gr/lit in an electroless bath. The phase analysis and surface morphology of the samples were characterized using x-ray diffraction and FESEM. The corrosion behavior of the coated samples was investigated in a 3.5 wt.% NaCl solution through potentiodynamic polarization, EIS, and electrochemical noise (EN) analyses. The corroded surface of the samples was further analyzed via FESEM observation after 10 days of immersion in corrosive medium. It was found that although adding 0.2 gr/lit CNT in electroless solution improves corrosion resistance, increasing CNT concentration from 0.2 up to 1 gr/lit increases the corrosion rate. The FESEM observations and EN results imply that the formation of micro-galvanic cells in samples with high concentration of CNTs leads to nucleation and growth of the pits. The results revealed that no passive layer was formed on the surface of the Ni-B sample, and the corrosion occurred through ionic diffusion into the cracks and crevices. The results of potentiodynamic test show that adding CNTs into electroless bath facilitates the formation of passive layer. However, results of EN test imply that increasing CNT concentration causes repetitive breakdown and recovery of passive film.

36 MATERIALS SCIENCE↗

Oxynitrided Surface Layer Produced On Ti6Al4V Titanium Alloy Under Low Temperature Glow Discharge Conditions For Medical Applications

In spite that titanium oxides increase biocompatibility of titanium implants but their functional life is limited due to the problems arising from brittles and metalosis. Therefore technology, that allow to produce composite surface layer with controlled microstructure, chemical and phase composition and surface morphology on titanium alloy and eliminates the oxides disadvantages has been existing till now is searched. The requirements of titanium and its alloys implants can be fulfill by the low-temperature glow discharge assisted oxynitriding.The paper describes the surface layer of TiO{sub 2}+TiN+Ti{sub 2}N+{alpha}Ti(N) type produced at temperature 680 deg. C that preserves mechanical properties of titanium alloy Ti6Al4V. Characteristics of produced diffusion multi-phase surface layers in range of phase composition, microstructure (SEM, TEM, XRD) and its properties, such as frictional wear resistance are presented. The biological properties in dependency to the applied sterilization method are also analyzed.Properties of produced surface layers are discussed with reference to titanium alloy. The obtained data show that produced surface layers improves titanium alloy properties both frictional wear and biological. Preliminary in vitro examinations show good biocompatibility and antithrombogenic properties.

36 MATERIALS SCIENCE↗

Influence of concentration and volume of precursor on the electrochemical properties of vanadium oxide thin films prepared by spray pyrolysis

Vanadium oxide (V{sub 2}O{sub 5}) thin films have been prepared by spray pyrolysis using different concentrations and volumes of precursor solution via aqueous route at 673K deposition temperature. The influences of concentration and volume on the structural, morphological and electrochemical properties of the deposited samples are studied well. X - ray diffraction study shows orthorhombic crystal structure with V{sub 2}O{sub 5} phase, confirmed by FTIR spectroscopy. Scanning electron microscopy shows granular, homogeneous and dense surface morphology. Cyclic voltammetery of all samples carried at all scan rates. Samples prepared using 0.05M, 40 ml of precursor solution shows highest specific capacitance 428.25 F/gm at 5 mV/s, Charge discharge behavior exhibits specific energy 18.73 Wh/kg, specific power 36.00 kW/kg, columbic efficiency 87.50 %. Impedance spectroscopy study was carried in the frequency range 1mHz – 1MHz, reveals pseudocapacitive behavior of the electrode exhibiting internal resistance 1.34 ohm.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Roles of Interface, Adherend, and Adhesive in Plasma- and Other-treated Joints of Metals and FRP Materials Under Shear Deformation

This work investigated the role of interface, adherend, and adhesive in adhesively-bonded metal-metal, metal-CFRTP, and CFRTP-CFRTP combinations with plasma-treated surfaces under shear deformation. To this end, aluminum alloys (AA5052 and AA6061) and short-carbon-fiber-reinforced polyamide 66 (CFRPA66) were used as examples and performed through single lap shear testing. The results showed that air plasma surface treatment can improve the shear behavior of adhesively-bonded AA5052-CFRPA66 and CFRPA66-CFRPA66 joints with about 20% enhanced lap shear strength compared to non-treated cases. Failure surface morphology of plasma-treated CFRPA66 adherend confirmed this improvement by showing an increased amount of adhesive failure than interfacial failure between CFRPA66 and adhesive. But this is not true for AA5052-AA6061 joints with plasma-treated surfaces exhibiting almost no enhanced lap shear strength. This study also showed the importance of selecting a proper surface modification method for the enhancement of adhesive-bonded structures under shear deformation through the analysis of the results in this study and in the literature. For fiber-reinforced polymers (FRPs), improving FRP/adhesive interface may be prioritized via different surface modification methods (e.g., plasma, chemical coating, etc.) than adhesive modification methods. However, for surface-cleaned metals, toughening adhesive via different enhancement methods (e.g., nano-particles, chemical enhancement, etc.) may be more important than improving metal/adhesive interface. These insightful results are valuable in the area of multi-materials joining.

Qiao, Yao↗

Note: A method for minimizing oxide formation during elevated temperature nanoindentation

A standardized method to protect metallic samples and minimize oxide formation during elevated-temperature nanoindentation was adapted to a commercial instrument. Nanoindentation was performed on Al (100), Cu (100), and W (100) single crystals submerged in vacuum oil at 200 °C, while the surface morphology and oxidation was carefully monitored using atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The results were compared to room temperature and 200 °C nanoindentation tests performed without oil, in order to evaluate the feasibility of using the oil as a protective medium. Extensive surface characterization demonstrated that this methodology is effective for nanoscale testing.

36 MATERIALS SCIENCE↗

Polarization characteristics of surface plasmon resonance in SnO{sub 2} nanocluster films

Internal reflection features caused by the surface plasmon resonance in nanoscale films containing defect tin dioxide clusters in the stoichiometric dielectric matrix are studied by the method of polarization modulation of electromagnetic radiation. The angular and spectral characteristics of reflectances R{sub s}{sup 2} and R{sub p}{sup 2} of s- and p-polarized radiation and their polarization difference {rho} = R{sub s}{sup 2} - R{sub p}{sup 2} are measured in the wavelength range {lambda} = 400-1600 nm. The experimental characteristics {rho}({theta}, {lambda}) ({theta} is the radiation incidence angle) obtained represent the optical property features associated with the film structure and morphology. Surface plasmon polaritons and local plasmons excited by s- and p-polarized radiation are detected; their frequency and relaxation properties are determined. The structural sensitivity of the technique for studying the surface plasmon resonance for tin dioxide films is shown.

36 MATERIALS SCIENCE↗

Pattern formation on free surfaces via plastic buckling and periodic folding

Spontaneous formation of surface patterns such as folds and creases is widely observed in engineered systems, such as thin films and machined surfaces, as well as in natural systems such as floral petals and leaves. A recognized route for their formation is via surface elastic instabilities. Here we demonstrate an alternate route for their formation —plastic buckling and folding—that occurs when ductile materials are subject to large-strain (>1) deformation. Using in situ imaging of simple-shear deformation of polypropylene, we delineate the mechanics underlying formation of folds and the resulting surface morphology. Here, the fold pattern shows a single wavelength that scales linearly with the size of the plastic zone. An analytical model predicts onset of the plastic buckling instability and characteristics of the folds. Besides obvious applications for controllably generating surface features over large areas, our results suggest a contributing mechanism for origin of surface roughness in solids.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Crystallization study of amorphous sputtered NiTi bi-layer thin film

The crystallization of Ni-rich/NiTiCu bi-layer thin film deposited by magnetron sputtering from two separate alloy targets was investigated. To achieve the shape memory effect, the NiTi thin films deposited at room temperature with amorphous structure were annealed at 773 K for 15, 30, and 60 min for crystallization. Characterization of the films was carried out by differential scanning calorimetry to indicate the crystallization temperature, grazing incidence X-ray diffraction to identify the phase structures, atomic force microscopy to evaluate surface morphology, scanning transmission electron microscopy to study the cross section of the thin films. The results show that the structure of the annealed thin films strongly depends on the temperature and time of the annealing. Crystalline grains nucleated first at the surface and then grew inward to form columnar grains. Furthermore, the crystallization behavior was markedly affected by composition variations. - Highlights: • A developed bi-layer Ni45TiCu5/Ni50.8Ti was deposited on Si substrate and crystallized. • During crystallization, The Ni{sub 45}TiCu{sub 5} layer is thermally less stable than the Ni-rich layer. • The activation energy is 302 and 464 kJ/mol for Cu-rich and Ni-rich layer in bi-layer, respectively.

36 MATERIALS SCIENCE↗

Electronic transport in graphene-based heterostructures

While boron nitride (BN) substrates have been utilized to achieve high electronic mobilities in graphene field effect transistors, it is unclear how other layered two dimensional (2D) crystals influence the electronic performance of graphene. In this Letter, we study the surface morphology of 2D BN, gallium selenide (GaSe), and transition metal dichalcogenides (tungsten disulfide (WS{sub 2}) and molybdenum disulfide (MoS{sub 2})) crystals and their influence on graphene's electronic quality. Atomic force microscopy analysis shows that these crystals have improved surface roughness (root mean square value of only ∼0.1 nm) compared to conventional SiO{sub 2} substrate. While our results confirm that graphene devices exhibit very high electronic mobility (μ) on BN substrates, graphene devices on WS{sub 2} substrates (G/WS{sub 2}) are equally promising for high quality electronic transport (μ ∼ 38 000 cm{sup 2}/V s at room temperature), followed by G/MoS{sub 2} (μ ∼ 10 000 cm{sup 2}/V s) and G/GaSe (μ ∼ 2200 cm{sup 2}/V s). However, we observe a significant asymmetry in electron and hole conduction in G/WS{sub 2} and G/MoS{sub 2} heterostructures, most likely due to the presence of sulphur vacancies in the substrate crystals. GaSe crystals are observed to degrade over time even under ambient conditions, leading to a large hysteresis in graphene transport making it a less suitable substrate.

36 MATERIALS SCIENCE↗

Effect of insulator surface conditioning on the pinch dynamics and x-ray production of a Ne-filled dense plasma focus

The dense plasma focus (DPF) can be an intense source of x rays, wherein the insulator sleeve strongly dictates the electrical breakdown, which subsequently affects the formation of a plasma sheath and a collapse phase. Experiments on a 25 kJ DPF (operated at 4.4 kJ) are carried out to demonstrate the influence of insulator surface morphology on the pinch structure, dynamics, and x-ray yield using a Ne fill. Two borosilicate insulators are directly compared, one with a smooth finish and the other machined with four circumferential grooves traversing the perimeter of the exterior insulator surface. Comparisons are made through same-shot imaging diagnostics of the evolving plasma sheath during breakdown, rundown, and at the pinch in addition to the time-resolved measurements of emitted x rays via filtered photodiodes. The presence of structures on the insulator sleeve reduces x-ray production across all fill pressures by a factor of 2.8 ± 2.4 on average and reduces the highest x ray producing shots by a factor of 5. ± 1.8. Observations of sheath asymmetry and inhomogeneity at lift-off are observed and correlated with subsequent observations of off-axis radial collapse. Taken together, this suggests that local variations in the insulator surface decrease the spatial uniformity of the sheath, leading to an azimuthally asymmetric focus, reduced electron densities, and, ultimately, degraded x-ray production.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Two-Step Synthesis of Poly (urea formaldehyde) Microcapsules

Self-healing coatings have potential to reduce waste and minimize repair costs in industries where materials need to be protected from harsh environmental conditions and mechanical abrasion. These coatings can be created by embedding healing-agent filled microcapsules which release their contents and fill voids in the event of damage. To synthesize microcapsules that are ideal for self-healing coatings, they must have a diameter less than 100 microns, smooth surface morphology, and have improved dispersibility. Our current one-step method does not produce microcapsules within the desired size distribution, so a two-step route where oligomers of the shell wall material are formed prior to microcapsule formation was investigated. This was done by evaluating the effects of solution viscosity, size of reaction vessel, addition of poly (vinyl alcohol) (PVA), and core/shell ratio on microcapsule properties. Characterization of microcapsule size, morphology, and composition was done using optical microscopy, Fourier-transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). Microcapsules with an average diameter of 78 ± 16 microns were successfully synthesized. Further work must be done to minimize PUF crystallites on the surface of the microcapsules.

36 MATERIALS SCIENCE↗

Synthesis, morphology and optical properties of GaN and AlGaN semiconductor nanostructures

Hexagonal Gallium Nitride (GaN) and Aluminum Gallium Nitride (AlGaN) nanoparticles were synthesized by sol-gel method using Ethylene Diamine Tetra Acetic acid (EDTA) complex route. Powder X-ray diffraction (PXRD) analysis confirms the hexagonal wurtzite structure of GaN and Al{sub 0.25}Ga{sub 0.75}N nanoparticles. Surface morphology and elemental analysis were carried out by Scanning Electron Microscope (SEM) and Energy Dispersive X-ray spectroscopy (EDX). The room temperature Photoluminescence (PL) study shows the near band edge emission for GaN at 3.35 eV and at 3.59 eV for AlGaN nanoparticles. The Aluminum (Al) composition of 20% has been obtained from PL emission around 345 nm.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗