Search NASA⌕ Search

SEARCH · Search NASA

Results for “sweep testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

An experimental study of pressures on 60 deg Delta wings with leading edge vortex flaps

An experimental study was conducted in the Virginia Tech Stability Wind Tunnel to determine surface pressures over a 60 deg sweep delta wing with three vortex flap designs. Extensive pressure data was collected to provide a base data set for comparison with computational design codes and to allow a better understanding of the flow over vortex flaps. The results indicated that vortex flaps can be designed which will contain the leading edge vortex with no spillage onto the wing upper surface. However, the tests also showed that flaps designed without accounting for flap thickness will not be optimum and the result can be oversized flaps, early flap vortex reattachment and a second separation and vortex at the wing/flap hinge line.

Marchman, J. F., III↗

Switching Characteristics of a 4H-SiC Based Bipolar Junction Transistor to 200 C

Static curves and resistive load switching characteristics of a 600 V, 4 A rated, SiC-based NPN bipolar power transistor (BJT) were observed at selected temperatures from room to 200 C. All testing was done in a pulse mode at low duty cycle (approx.0.1 percent). Turn-on was driven by an adjustable base current pulse and turn-off was accelerated by a negative base voltage pulse of 7 V. These base drive signals were implemented by 850 V, gated power pulsers, having rise-times of roughly 10 ns, or less. Base charge sweep-out with a 7 V negative pulse did not produce the large reverse base current pulse seen in a comparably rated Si-based BJT. This may be due to a very low charge storage time. The decay of the collector current was more linear than its exponential-like rise. Switching observations were done at base drive currents (I(sub B)) up to 400 mA and collector currents (I(sub C)) up to 4 A, using a 100 Omega non-inductive load. At I(sub B) = 400 mA and I(sub C) = 4 A, turn-on times typically varied from 80 to 94 ns, over temperatures from 23 to 200 C. As expected, lowering the base drive greatly extended the turn-on time. Similarly, decreasing the load current to I(sub C) = 1 A with I(sub B) = 400 mA produced turn-on times as short as 34 ns. Over the 23 to 200 C range, with I(sub B) = 400 mA and I(sub C) = 4 A, turn-off times were in the range of 72 to 84 ns with the 7 V sweep-out.

Niedra, Janis M.↗

Parametric Deformation of Discrete Geometry for Aerodynamic Shape Design

We present a versatile discrete geometry manipulation platform for aerospace vehicle shape optimization. The platform is based on the geometry kernel of an open-source modeling tool called Blender and offers access to four parametric deformation techniques: lattice, cage-based, skeletal, and direct manipulation. Custom deformation methods are implemented as plugins, and the kernel is controlled through a scripting interface. Surface sensitivities are provided to support gradient-based optimization. The platform architecture allows the use of geometry pipelines, where multiple modelers are used in sequence, enabling manipulation difficult or impossible to achieve with a constructive modeler or deformer alone. We implement an intuitive custom deformation method in which a set of surface points serve as the design variables and user-specified constraints are intrinsically satisfied. We test our geometry platform on several design examples using an aerodynamic design framework based on Cartesian grids. We examine inverse airfoil design and shape matching and perform lift-constrained drag minimization on an airfoil with thickness constraints. A transport wing-fuselage integration problem demonstrates the approach in 3D. In a final example, our platform is pipelined with a constructive modeler to parabolically sweep a wingtip while applying a 1-G loading deformation across the wingspan. This work is an important first step towards the larger goal of leveraging the investment of the graphics industry to improve the state-of-the-art in aerospace geometry tools.

Anderson, George R.↗

Quiet High Speed Fan II (QHSF II): Final Report

This report details the aerodynamic, mechanical, structural design and fabrication of a Honey Engines Quiet High Speed Fan II (lower hub/tip ratio and higher specific flow than the Baseline I fan). This fan/nacelle system incorporates features such as advanced forward sweep and an advanced integrated fan/fan exit guide vane design that provides for the following characteristics: (1) Reduced noise at supersonic tip speeds, in comparison to current state-of-the-art fan technology; (2) Improved aeroelastic stability within the anticipated operating envelope; and (3) Aerodynamic performance consistent with current state-of-the-art fan technology. This fan was fabricated by Honeywell and tested in the NASA Glenn 9- by 15-Ft Low Speed Wind Tunnel for aerodynamic, aeromechanical, and acoustic performance.

Kontos, Karen↗

Advanced Test Reactor Safety Basis Update for Gas-Cooled Experiments

The Advanced Test Reactor (ATR) supports neutron irradiation of several types of experiments. One such experiment type is referred to as a gas leadout. Gas leadout experiments actively flow gas through the experiment which allows for active temperature control. It also allows for in-situ data of the experiment. For example, fission gas migration through a fuel sample can be monitored via activity of the sweep gas. Historically, ex-pile equipment and fission product monitors were housed in shielded ATR cubicles. Due to other facility updates, cubicle space is no longer available for gas leadout experiment equipment. To support continued operation of gas leadout experiments, ATR completed a safety basis update that supports a new housing for leadout equipment that may process potentially contaminated gas. In addition to the structure and associated equipment, technical safety requirements regarding handling and storage of experiments needed to be revised to support fueled gas leadout experiments and associated outage configurations. The safety basis update addressed the full lifecycle of these experiments, including experiment movement and interim storage, and credible abnormal events such as failures or leaks in contaminated gas tubing in occupied areas. This paper discusses the completed analyses performed to support the safety basis update associated with gas leadout experiments, including thermal-hydraulic evaluation, probabilistic analysis, and dose consequence analyses.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sparse, iterative simulation methods for one-dimensional laminar flames

Sparse, iterative simulation methods for one-dimensional laminar flames are proposed. The resulting steady and unsteady flame solvers exploit approximate Jacobians to greatly reduce the computational cost associated with matrix operations. The constant, non-unity Lewis number assumption is introduced to further reduce the computational cost. The solvers are also parallelized to reduce time-to-solution on distributed memory computer systems. Computed laminar flame speeds and species profiles for a range of chemical mechanisms (from 10 to 2878 species) are compared against a well-validated commercial code and are found to be consistent within solver tolerances. The computation times of both the unsteady and steady solutions increase only linearly with the number of species, which is a significant improvement over the quadratic or cubic scaling of existing steady-state flame solvers. For the largest mechanism tested, the steady-state flame solver is two orders of magnitude faster than commonly-used codes. The use of an approximate Jacobian is shown to reduce the rate of convergence for the steady-state solver, but does not significantly affect the domain of convergence. The steady-state solver with approximate Jacobian is thus well suited for computationally efficient laminar flame speed sweeps with large kinetic mechanisms.

42 ENGINEERING↗

Low-speed aerodynamic characteristics of a transport configuration having a 42 deg swept supercritical airfoil wing and three tail height positions

A low speed investigation was conducted in the Langley V/STOL tunnel to define the static stability characteristics of an advanced high subsonic speed transport aircraft model in the cruise configuration (no high lift system). The wing of the model had 42 deg sweep of the quarter chord line, an aspect ratio of 6.78, and supercritical airfoil sections. Three different horizontal tail configurations (high, mid, and low) were investigated on the complete model and for the model with the wing removed in order to assess effects of the wing flow field on the tail contributions to both longitudinal and lateral stability characteristics. All the model configurations investigated were tested over an angle of attack range from approximately -5 to 23 deg. Some model configurations were also tested over an angle of attack range from about 11 to 38 deg in order to explore the aerodynamic characteristics in the deep stall region.

Fournier, P. G.↗

AFTI/F-111 airplane mission adaptive wing operational flight evaluation technique using uplinked pilot command cues

NASA and the USAF have conducted a program to investigate aircraft performance improvements utilizing a mission adaptive wing (MAW). The MAW was designed and developed for the AFTI/F-111 variable-sweep aircraft to provide a hydraulically driven, smooth, and continuous variable camber of the trailing and leading edges as a function of maneuvering requirements or of flight conditions. The remotely augmented vehicle facility (RAV) at the NASA DFRF, as utilized in the MAW investigations, is described. The RAV was a dedicated, ground based, general purpose facility capable of receiving a data stream downlinked from a test vehicle, processing this data stream in a digital computer, and transmitting processed data back to the test vehicle. It is shown that this method of flight testing provides a technique that can evaluate highly dynamic maneuvers.

Kempel, Robert W.↗

A scheme for theoretical and experimental evaluation of multivariable system stability robustness

A scheme for theoretical and experimental evaluation of multivariable system stability robustness measures is described. The experimental scheme is based on the estimation of frequency responses from power-spectra analyses of a set of time responses due to sine-sweep excitation at each input and then computation of the appropriate singular values. The procedure can also be used on an open-loop stable system to predict the closed-loop stability before closing the loop. Classical Nyquist diagrams can also be constructed to determine one-loop-at-a-time gain or phase margins. The scheme has been implemented in a wind tunnel test for singular-value evaluation of digital flutter suppression control laws and compared with theory. The singular values at the plant input and output of the actual system and the theoretical model are qualitatively similar but have some discrepancies.

Mukhopadhyay, Vivek↗

Application of high-alpha control system concepts to a variable-sweep fighter airplane

The use of control system design to enhance high-angle-of-attack flying qualities and departure/spin resistance has become an accepted and widely used approach for modern fighter aircraft. NASA and the Navy are currently conducting a joint research program to investigate the application of this technology to the F-14. The paper discusses the results of this program within the context of its contributions to advancing high-alpha control system technology. General topics covered include (1) analysis and design tools, (2) control system design approach, and (3) flight test approach and results.

Nguyen, L. T.↗

Improvement of transport-corrected scattering stability and performance using a Jacobi inscatter algorithm for 2D-MOC

The MPACT code, being developed collaboratively by the University of Michigan and Oak Ridge National Laboratory, is the primary deterministic neutron transport solver being deployed within the Virtual Environment for Reactor Applications (VERA) as part of the Consortium for Advanced Simulation of Light Water Reactors (CASL). In many applications of the MPACT code, transport-corrected scattering has proven to be an obstacle in terms of stability, and considerable effort has been made to try to resolve the convergence issues that arise from it. Most of the convergence problems seem related to the transport-corrected cross sections, particularly when used in the 2D method of characteristics (MOC) solver, which is the focus of this work. Here in this paper, the stability and performance of the 2-D MOC solver in MPACT is evaluated for two iteration schemes: Gauss-Seidel and Jacobi. With the Gauss-Seidel approach, as the MOC solver loops over groups, it uses the flux solution from the previous group to construct the inscatter source for the next group. Alternatively, the Jacobi approach uses only the fluxes from the previous outer iteration to determine the inscatter source for each group. Consequently for the Jacobi iteration, the loop over groups can be moved from the outermost loop$-$as is the case with the Gauss-Seidel sweeper$-$to the innermost loop, allowing for a substantial increase in efficiency by minimizing the overhead of retrieving segment, region, and surface index information from the ray tracing data. Several test problems are assessed: (1) Babcock & Wilcox 1810 Core I, (2) Dimple S01A-Sq, (3) VERA Progression Problem 5a, and (4) VERA Problem 2a. The Jacobi iteration exhibits better stability than Gauss-Seidel, allowing for converged solutions to be obtained over a much wider range of iteration control parameters. Additionally, the MOC solve time with the Jacobi approach is roughly 2.0-2.5× faster per sweep. While the performance and stability of the Jacobi iteration are substantially improved compared to the Gauss-Seidel iteration, it does yield a roughly 8$-$10% increase in the overall memory requirement.

97 MATHEMATICS AND COMPUTING↗

Hydrogen permeability and stability of palladium films in a high pressure reactor

Palladium (Pd) thin films were fabricated by colloidal spray deposition (CSD) on substrates of porous yttrium stabilized zirconium oxide (YSZ). The films were sintered at 1140–1160 °C for 2–3 h in argon and had thickness of 5–11 μm. The hydrogen (H 2 ) permeation flux for the Pd film was measured with simulated feed gases (90% H 2 /He, syn-gas/steam, or syn-gas/steam with H 2 S) flowing on the film side and sweep gas (Ar) flowing on the substrate side. Here, the hydrogen flux with the Pd film was obtained by adjusting the flow rate and pressure of the gas. Hydrogen flux values of 121–173 cm 3 min -1 cm -2 were measured at 388–596 °C (feed: 90% H 2 /He at 200 mL min -1 ; sweep: Ar at 1400 mL min -1 ; and ΔP = ~170 psi), and the permeability was calculated and compared with literature values. Because Pd is known to be sensitive to some gases, the stability of Pd films was evaluated by examining the microstructures of samples after their exposure to gas mixtures containing CO, CO 2 , H 2 O, and H 2 S. From the results of stability tests in H 2 S-containing atmospheres, the Pd/Pd 4 S phase boundary was determined, and this measured boundary was compared to the Pd/Pd 4 S boundary calculated from the thermodynamic data in the literature.

36 MATERIALS SCIENCE↗

Low-speed static longitudinal and lateral stability characteristics of two low-aspect-ratio wings cambered and twisted to provide a uniform load at a supersonic flight condition

A delta wing and a tapered sweptback wing of aspect ratios 1.56 and 2.00, respectively, both of which were cambered and twisted so as to provide a uniform load distribution for a supersonic flight condition, were tested in combination with a fuselage at Reynolds numbers between 384,000 and 1,550,000 in order to determine the low-speed lift-drag and static stability characteristics of such wings.

REYNOLDS NUMBER EFFECTS - COMPLETE WINGS↗

Regenerative Gas Dryer for In-Situ Propellant Production

Rocket propellant can be produced anywhere that water is found by splitting it into hydrogen and oxygen, potentially saving several tons of mass per mission and enabling the long term presence of humans in space beyond LEO. When water is split into hydrogen and oxygen, the gaseous products can be very humid (several thousand ppm). Propellant-grade gases need to be extremely dry before being converted into cryogenic liquids (less than 26 ppm water for grade B Oxygen). The primary objective of this project is to design, build and test a regenerative gas drying system that can take humid gas from a water electrolysis system and provide dry gas (less than 26ppm water) to the inlet of a liquefaction system for long durations. State of the art work in this area attempted to use vacuum as a means to regenerate desiccant, but it was observed that water would migrate to the dry zone without a sweep gas present to direct the desorbed vapor. Further work attempted to use CO2 as a sweep gas, but this resulted in a corrosive carbonic acid. In order for in-situ propellant production to work, we need a way to continuously dry humid gas that addresses these issues.

Paz, Aaron↗

V344 LYRAE: A TOUCHSTONE SU UMa CATACLYSMIC VARIABLE IN THE KEPLER FIELD

We report on the analysis of the Kepler short-cadence (SC) light curve of V344 Lyr obtained during 2009 June 20 through 2010 March 19 (Q2-Q4). The system is an SU UMa star showing dwarf nova (DN) outbursts and superoutbursts, and promises to be a touchstone for CV studies for the foreseeable future. The system displays both positive and negative superhumps with periods of 2.20 and 2.06 hr, respectively, and we identify an orbital period of 2.11 hr. The positive superhumps have a maximum amplitude of {approx}0.25 mag, the negative superhumps have a maximum amplitude of {approx}0.8 mag, and the orbital period at quiescence has an amplitude of {approx}0.025 mag. The quality of the Kepler data is such that we can test vigorously the models for accretion disk dynamics that have been emerging in the past several years. The SC data for V344 Lyr are consistent with the model that two physical sources yield positive superhumps: early in the superoutburst, the superhump signal is generated by viscous dissipation within the periodically flexing disk, but late in the superoutburst, the signal is generated as the accretion stream bright spot sweeps around the rim of the non-axisymmetric disk. The disk superhumps are roughly anti-phased with the stream/late superhumps. The V344 Lyr data also reveal negative superhumps arising from accretion onto a tilted disk precessing in the retrograde direction and suggest that negative superhumps may appear during the decline of DN outbursts. The period of negative superhumps has a positive P-dot in between outbursts.

79 ASTRONOMY AND ASTROPHYSICS↗

MEMBRANE PROCESS TO SEQUESTER CO2 FROM POWER PLANT FLUE GAS

The objective of this project was to assess the feasibility of using a membrane process to capture CO2 from coal-fired power plant flue gas. During this program, MTR developed a novel membrane (Polaris™) with a CO2 permeance tenfold higher than commercial CO2-selective membranes used in natural gas treatment. The Polaris™ membrane, combined with a process design that uses a portion of combustion air as a sweep stream to generate driving force for CO2 permeation, meets DOE post-combustion CO2 capture targets. Initial studies indicate a CO2 separation and liquefaction cost of $20 - $30/ton CO2 using about 15% of the plant energy at 90% CO2 capture from a coal-fired power plant. Production of the Polaris™ CO2 capture membrane was scaled up with MTR’s commercial casting and coating equipment. Parametric tests of cross-flow and countercurrent/sweep modules prepared from this membrane confirm their near-ideal performance under expected flue gas operating conditions. Commercial-scale, 8-inch diameter modules also show stable performance in field tests treating raw natural gas. These findings suggest that membranes are a viable option for flue gas CO2 capture. The next step will be to conduct a field demonstration treating a realworld power plant flue gas stream. The first such MTR field test will capture 1 ton CO2/day at Arizona Public Service’s Cholla coal-fired power plant, as part of a new DOE NETL funded program.

03 NATURAL GAS↗

V344 Lyrae: A Touchtone SU UMa Cataclysmic Variable in the Kepler Field

We report on the analysis of the Kepler short-cadence (SC) light curve of V344 Lyr obtained during 2009 June 20 through 2010 Mar 19 (Q2-Q4). The system is an SU UMa star showing dwarf nova outbursts and superoutbursts, and promises to be a touchstone for CV studies for the foreseeable future. The system displays both positive and negative super humps with periods of 2.20 and 2.06-hr, respectively, and we identify an orbital period of 2.11-hr. The positive super humps have a maximum amplitude of approximately 0.025-mag, the negative super humps a maximum amplitude of approximately 0.8 mag, and the orbital period at quiescence has an amplitude of approximately 0.025 mag. The quality of the Kepler data is such that we can test vigorously the models for accretion disk dynamics that have been emerging in the past several years. The SC data for V344 Lyr are consistent with the model that two physical sources yield positive superhumps: early in the superoutburst. the superhump signal is generated by viscous dissipation within the periodically flexing disk. but late in the superoutburst, the signal is generated as the accretion stream bright spot sweeps around the rim of the non-axisymmetric disk. The disk super humps are roughly anti-phased with the stream/late superhumps. The V344 Lyr data also reveal negative super humps arising from accretion onto a tilted disk precessing in the retrograde direction, and suggest that negative superhumps may appear during the decline of DN outbursts. The period of negative superhumps has a positive P(raised dot) in between outbursts.

Smale, Alan P.↗

Real-Time Adaptive Drag Minimization Wind Tunnel Investigation of a Flexible Wing with Variable Camber Continuous Trailing Edge Flap System

This paper reports the results of a recently completed real-time adaptive drag minimization wind tunnel investigation of a highly flexible wing wind tunnel model equipped with the Variable Camber Continuous Trailing Flap (VCCTEF) technology at the University of Washington Aeronautical Laboratory (UWAL). The wind tunnel investigation is funded by NASA SBIR Phase II contract with Scientific Systems Company, Inc. (SSCI) and University of Washington (UW) as a subcontractor. The wind tunnel model is a sub-scale Common Research Model (CRM) wing constructed of foam core and fiberglass skin and is aeroelastically scaled to achieve a wing tip deflection of 10% of the wing semi-span which represents a typical wing tip deflection for a modern transport such as Boeing 787. The jig-shape twist of the CRM wing is optimized using a CART3D aero-structural model to achieve the minimum induced drag for the design cruise lift coefficient of 0.5. The wing is equipped with two chord wise cambered segments for each of the six span wise flap sections for a total of 12 individual flap segments that comprise the VCCTEF system. Each of the 12 flap segments is actively controlled by an electric servo-actuator. The real-time adaptive drag optimization strategy includes an on-board aerodynamic model identification, a model excitation, and a real-time drag optimization. The on-board aerodynamic model is constructed parametrically as a function of the angle of attack and flap positions to model the lift and drag coefficients of the wing. The lift coefficient models include a linear model and a second-order model. The drag coefficient models include a quadratic model and a higher-order up to 6th-order model to accurately model the drag coefficient at high angles of attack. The onboard aerodynamic model identification includes a recursive least-squares (RLS) algorithm and a batch least-squares (BLS) algorithm designed to estimate the model parameters. The model excitation method is designed to sample the input set that comprises the angle of attack and the flap positions. Three model excitation methods are developed: random excitation method, sweep method, and iterative angle-of-attack seeking method. The real-time drag optimization includes a generic algorithm developed by SSCI and several optimization methods developed by NASA which include a second-order gradient Newton-Raphson optimization method, an iterative gradient optimization method, a pseudo-inverse optimization method, an analytical optimization method, and an iterative refinement optimization method. The first wind tunnel test entry took place in September 2017. This test revealed major hardware issues and required further redesign of the flap servo mechanisms. The second test entry took place in April 2018. However, the test was not successful due to the issues with the onboard aerodynamic model identification RLS algorithm which incorrectly identified model parameters. This test also provides an experimental comparison study between the VCCTEF and a variable camber discrete trailing edge flap (VCDTEF) without the elastomer transition mechanisms. The experimental result confirms the benefit of the VCCTEF which produces lower drag by 5% than the VCDTEF. The third and final test entry took place in June 2018 after the issues with the RLS algorithm have been identified and corrected. Additional improvements were implemented. These include the BLS algorithm, the iterative angle-of-attack seeking method, the iterative gradient optimization method, and the pseudo-inverse optimization method. The test objectives were successfully demonstrated as the real-time drag optimization identifies several optimal solutions at off-design lift coefficients. The iterative gradient optimization method is found to achieve up to 4.7% drag reduction for the off-design lift coefficient of 0.7. The pseudo-inverse optimization method which does not require the drag coefficient model is found to be quite effective in reducing drag. Up to 9.4% drag reduction for the off-design lift coefficient of 0.7 is achieved with the pseudo-inverse optimization method. The wind tunnel investigation demonstrates the potential of real-time drag optimization technology. Several new capabilities are developed that could enable future adaptive wing technologies for flexible wings equipped with drag control devices such as the VCCTEF.

Drag Optimization↗