Search NASA⌕ Search

SEARCH · Search NASA

Results for “tracking data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

Towards the GEOSAT Follow-On Precise Orbit Determination Goals of High Accuracy and Near-Real-Time Processing

The US Navy's GEOSAT Follow-On spacecraft (GFO) primary mission objective is to map the oceans using a radar altimeter. Satellite laser ranging data, especially in combination with altimeter crossover data, offer the only means of determining high-quality precise orbits. Two tuned gravity models, PGS7727 and PGS7777b, were created at NASA GSFC for GFO that reduce the predicted radial orbit through degree 70 to 13.7 and 10.0 mm. A macromodel was developed to model the nonconservative forces and the SLR spacecraft measurement offset was adjusted to remove a mean bias. Using these improved models, satellite-ranging data, altimeter crossover data, and Doppler data are used to compute both daily medium precision orbits with a latency of less than 24 hours. Final precise orbits are also computed using these tracking data and exported with a latency of three to four weeks to NOAA for use on the GFO Geophysical Data Records (GDR s). The estimated orbit precision of the daily orbits is between 10 and 20 cm, whereas the precise orbits have a precision of 5 cm.

Lemoine, Frank G.↗

Telecommunications Relay Support of the Mars Phoenix Lander Mission

The Phoenix Lander, first of NASA's Mars Scout missions, arrived at the Red Planet on May 25, 2008. From the moment the lander separated from its interplanetary cruise stage shortly before entry, the spacecraft could no longer communicate directly with Earth, and was instead entirely dependent on UHF relay communications via an international network of orbiting Mars spacecraft, including NASA's 2001 Mars Odyssey (ODY) and Mars Reconnaissance Orbiter (MRO) spacecraft, as well as ESA's Mars Express (MEX) spacecraft. All three orbiters captured critical event telemetry and/or tracking data during Phoenix Entry, Descent and Landing. During the Phoenix surface mission, ODY and MRO provided command and telemetry services, far surpassing the original data return requirements. The availability of MEX as a backup relay asset enhanced the robustness of the surface relay plan. In addition to telecommunications services, Doppler tracking observables acquired on the UHF link yielded an accurate position for the Phoenix landing site.

Edwards, Charles D., Jr.↗

Mars Aerobraking Spacecraft State Estimation by Processing Inertial Measurement Unit Data

Aerobraking is an efficient technique for orbit adjustment of planetary spacecraft, such as Magellan (Venus), Mars Global Surveyor, and Mars Odyssey. Determination of the vehicle state during the aerobraking phase has conventionally been performed using only radiometric tracking data prior to and following the atmospheric drag pass. This approach is sufficiently accurate and timely to meet current mission operational requirements; however, it is expensive in terms of ground support and leads to delayed results because ofthe need for post-drag pass data. This research presents a new approach to estimation of the vehicle state during the atmospheric pass that sequentially incorporates observations from an Inertial Measurement Unit (IMU) and models of the vehicle and environment. The approach, called Inertial Measurements for Aerobraking Navigation (IMAN), is shown to perform at a level comparable to the conventional methods in terms of navigation accuracy and superior to them in terms of availability of the results immediately after completion ofthe pass. Furthermore, the research shows that IMAN can be used to reliably predict subsequent periapsis times and locations over all aerobraking regimes. IMAN also yields accurate peak dynamic pressure and heating rates, critical for a successful corridor control strategy, comparable to navigation team reconstructed values. This research also provides the first instance of the utilization of the Unscented Kalman Filter for the purpose of estimating an actual spacecraft trajectory arc about another planet.

Unscented Kalman Filter↗

Reconstruction of the 1st Space Shuttle (STS-1) entry trajectory

A discussion of the generation of the best estimate trajectory (BET) of the first Space Shuttle Orbiter entry flight is presented. The BET defines a time history of the state, attitude, and atmospheric relative parameters throughout the Shuttle entry from an altitude of approximately 183 km to rollout. The inertial parameters were estimated utilizing a weighted least squares batch filter algorithm. Spacecraft angular rate and acceleration data derived from the Inertial Measurement Unit were utilized to predict the state and attitude which was constrained in a weighted least squares process to fit external tracking data consisting of ground based S-band and C-band data. Refined spacecraft altitude and velocity during and post rollout were obtained by processing artificial altimeter and Doppler data. The BET generation process is discussed. Software and data interface discussions are included. The variables and coordinate systems utilized are defined. STS-1 mission peculiar inputs are summarized. A listing of the contents of the actual BET is provided.

Findlay, J. T.↗

Circulation from a joint gravity field solution determination of the general ocean

With the development of satellite altimetry, it is possible to infer the geostrophic velocity of the surface ocean currents, if the geoid and the position of the satellite are known accurately. Errors in current geoid models and orbit computations, both due primarily to errors in the earth's gravity field model, have limited the use of altimeter data for this purpose. The objective of this investigation is to demonstrate that altimeter data can be used in a joint solution to simultaneously estimate the quasi-stationary sea surface topography, zeta, and the model for the gravity field. Satellite tracking data from twelve satellites were used along with Seasat altimeter data for the solution. The estimated model of zeta compares well at long wavelengths with the hydrographic model of zeta. Covariance analysis indicates that the geoid is separable from zeta up to degree 9, at which point geoid error is comparable to the signal of zeta.

Tapley, B. D.↗

Mars 2020 Radiometric Data and Telemetry Processing, Attitude Estimation, and Thruster Calibration for Orbit Determination

The Mars 2020 spacecraft was spin-stabilized during cruise, just like its predecessor, the Mars Science Laboratory. This spinning motion imparts a signature in the radiometric tracking data that must be dealt with in order to properly model the motion of the spacecraft's center of mass. We discuss how the Orbit Determination team pre-processed the data for efficient computations while also providing other benefits such as high-fidelity attitude modeling and on-board clock verification. Finally, we discuss the analysis and results of the in-flight thruster calibration activity.

Seubert, Jill↗

X-band noise temperature near the Sun at a 34-meter high efficiency antenna

The X-band system noise temperature near the Sun was measured at the DSS 15, a 34 meter high efficiency (HEF) antenna, in November 1987. Data was taken at angles off the center of the Sun from 0 to 4 degrees. At angles greater than 0.5 degree, the measured results agree with Voyager tracking data taken at solar conjunction in late December 1987. Within the solar disk, at angles lower than 0.27 degree, the temperature measured was lower than the prediction of a model by 30 percent, after adjusting for known receiver nonlinearities. The discrepancy in this extreme case is probably caused by unknown nonlinearities in the receiver, uncertainties in the model, or both. The measurement is nevertheless credible for practically all Sun-Earth-probe angles of interest to deep space missions.

Rebold, T. A.↗

The Starshine Hitchhiker Mission on STS-96

A mirrored, spherical "Starshine" satellite was ejected by NASA into a circular low Earth orbit from a Hitchhiker canister in the cargo bay of Space Shuttle OV-103 Discovery at 07:21 Universal Time on June 5, 1999, near the end of Discovery's STS-96 mission to the International Space Station. Starshine's initial orbital altitude was 218 Nautical Miles (387 km), and its orbital inclination was 51.6 deg. The satellite is expected to orbit Earth until sometime in January 2000, when it will reenter the atmosphere and vaporize. Some 25,030 students in 700 schools around the world participated in the construction of this satellite by polishing 878 small, front-surface aluminum mirrors that stud its outer surface. A small fraction of those students is presently tracking the satellite and measuring its angular position at specific times. The Naval Research Laboratory is combining the students' measurements with Naval Space Command radar tracking data to compute the satellite's orbit on a daily basis. From the rate of decay of the orbit, the students are able to calculate the density of the atmosphere at the satellite's present altitude. The students are also accessing the project's web site to observe ground-based and space-based images of the sun and other indices of solar activity. They are then using these data to make correlations between the intensity of solar storms and fluctuations in the density of the earth's upper atmosphere. The number of students participating in the tracking phase of the project is expected to increase dramatically at the start of the fall school term in the northern hemisphere. At the conclusion of the Starshine mission, the student team will attempt to predict when and where the satellite will re-enter the atmosphere, so they can compete for a cash prize for the best photograph of the satellite's fiery demise.

Moore, Gil↗

Toward decimeter Topex orbit determination using GPS

Several practical aspects of precision GPS-based Topex orbit determination are investigated. Multipath signals contaminating Topex pseudorange data are greatly reduced by placing the GPS antenna on a conducting backplate consisting of concentric choke rings to attenuate signals coming in from the Topex horizon and below, and by elevating it on a boom to keep it well above all reflecting surfaces. A proper GPS antenna cutoff view angle is chosen so that a sufficient number of GPS satellites with good geometry are in view while reception of reflected signals is minimized. The geometrical strength of the tracking data is optimized by properly selecting GPS satellites to be observed so as to provide data with moderate continuity, low PDOP, and common visibility with ground tracking sites. The tracking performance is greatly enhanced when three complementary sites are added to the minimum ground tracking network consisting of the three NASA DSN sites.

Wu, Sien-Chong↗

Methodology for Generating Conflict Scenarios by Time Shifting Recorded Traffic Data

A methodology is presented for generating conflict scenarios that can be used as test cases to estimate the operational performance of a conflict probe. Recorded air traffic data is time shifted to create traffic scenarios featuring conflicts with characteristic properties similar to those encountered in typical air traffic operations. First, a reference set of conflicts is obtained from trajectories that are computed using birth points and nominal flight plans extracted from recorded traffic data. Distributions are obtained for several primary properties (e.g., encounter angle) that are most likely to affect the performance of a conflict probe. A genetic algorithm is then utilized to determine the values of time shifts for the recorded track data so that the primary properties of conflicts generated by the time shifted data match those of the reference set. This methodology is successfully demonstrated using recorded traffic data for the Memphis Air Route Traffic Control Center; a key result is that the required time shifts are less than 5 min for 99% of the tracks. It is also observed that close matching of the primary properties used in this study additionally provides a good match for some other secondary properties.

Paglione, Mike↗

Gravity data analysis

Work on three different efforts related to gravity data analysis is discussed. The reduction of raw Doppler data from the Apollo 15 subsatellite to produce acceleration profiles as a function of latitude, longitude and altitude; an investigation related to fitting long arcs of Pioneer Venus Orbiter tracking data; and a study of gravity/topography ratios which were found to have a linear trend with longitude are discussed.

Sjogren, William L.↗

A high-fidelity N-body ephemeris generator for satellites in Earth orbit

A program is currently used for mission planning called the Analytic Satellite Ephemeris Program (ASEP), which produces projected data for orbits that remain fairly close to Earth. Lunar and solar perturbations are taken into account in another program called GRAVE. This project is a revision of GRAVE which incorporates more flexible means of input for initial data, provides additional kinds of output information, and makes use of structured programming techniques to make the program more understandable and reliable. The computer program ORBIT was tested against tracking data for the first 313 days of operation of the CRRES satellite. A sample graph is given comparing the semi-major axis calculated by the program with the values supplied by NORAD. When calculated for points at which CRRES passes through the ascending node, the argument of perigee, the right ascension of the ascending node, and the mean anomaly all stay within about a degree of the corresponding values from NORAD; the inclination of the orbital plane is much closer. The program value of the eccentricity is in error by no more than 0.0002.

Simmons, David R.↗

Tracking system options for future altimeter satellite missions

Follow-on missions to provide continuity in the observation of the sea surface topography once the successful TOPEX/POSEIDON (T/P) oceanographic satellite mission has ended are discussed. Candidates include orbits which follow the ground tracks of T/P GEOSAT or ERS-1. The T/P precision ephemerides, estimated to be near 3 cm root-mean-square, demonstrate the radial orbit accuracy that can be achieved at 1300 km altitude. However, the radial orbit accuracy which can be achieved for a mission at the 800 km altitudes of GEOSAT and ERS-1 has not been established, and achieving an accuracy commensurate with T/P will pose a great challenge. This investigation focuses on the radial orbit accuracy that can be achieved for a mission in the GEOSAT orbit. Emphasis is given to characterizing the effects of force model errors on the estimated radial orbit accuracy, particularly those due to gravity and drag. The importance of global, continuous tracking of the satellite for reduction in these sources of orbit error is demonstrated with simulated GPS tracking data. A gravity tuning experiment is carried out to show how the effects of gravity error may be reduced. Assuming a GPS flight receiver with a full-sky tracking capability, the simulation results indicate that a 5 cm radial orbit accuracy for an altimeter satellite in GEOSAT orbit should be achievable during low-drag atmospheric conditions and after an acceptable tuning of the gravity model.

Davis, G. W.↗

Mariner IX optical navigation using Mars lit limb

Optical spacecraft navigation data, i.e., the lit limb TV image of Mars, acquired during the approach phase of the Mariner IX spacecraft to Mars, has been successfully demonstrated to augment the radio spacecraft tracking data. Accurate in-flight calibration of the TV instrument and the scan platform was performed by referencing stars and planets. Simulated real-time processing and the detailed postflight analyses of the onboard optical data have shown that planet limb data is an important data source in a far-encounter period for which other types of onboard optical measurements, e.g., natural satellite(s) of the target planet with star background, may not be available.

Jerath, N.↗

Vehicle Tracking with Crop-based Detection

End-to-end production of vehicle tracking data from video in real-time and with high accuracy remains a challenging problem due to the computational cost of object detection on each frame. In this work we present Tracking with Crop-based Detection, a method for speeding object tracking in constrained contexts (with stable cameras and relatively-predictable object motion) such as vehicle traffic monitoring. We leverage this context to provide a strong prior for object locations, which we use to 1.) boost detection speed by detecting objects only in regions corresponding to object priors on most frames and 2.) inform the selection of the detector output for each object. We evaluate Crop-based Detection as an extension to the KIOU object tracker (Crop-KIOU) on the UA-DETRAC dataset. The proposed tracker outperforms all other reported algorithms in terms of PR-MOTA, PR-MOTP, and mostly tracked objects on the UA-DETRAC benchmark, establishing a new state-of-the-art. Relative to tracking by detection with KIOU, Crop-KIOU achieves a 26% higher frame-rate and increases accuracy. Furthermore, Tracking with Crop-based Detection can be combined with frame skipping; we show a 149% increase in framerate relative to KIOU with no decrease in accuracy using this combination of methods.

Gloudemans, Derek↗

Lunar Geodetic Opportunities with the Laser Altimeter on LRO

The Lunar Reconnaissance Orbiter (LRO) is to be launched at the end of 2008 and will carry 7 instruments, one of which is a laser altimeter (LOLA), and obtain observations of the Moon for a period of 1 year. The orbit will be near polar and approximately circular at 50 km altitude with monthly orbital adjustments to maintain the mean altitude. The LOLA instrument has a -10 cm single-shot accuracy, with 5 beams, and operates at 28 Hz. It provides 5 adjacent profiles, each approximately 12 to 15 meters apart with a swath of approximately 65 meters. The 5 beams are arranged in a cross-shaped pattern that provides simultaneous along and cross track altimetry and providing slopes in 2 orthogonal directions every 50 meters along track. In combination with the LRO tracking data LOLA will be used to improve the model of the lunar gravity by using the altimeter on both the lunar near-side and far-side as an additional tracking system to enable precise positioning of the LRO spacecraft at about the 50 meter level rms. The instrument is expected to provide full polar coverage at very high northern and southern latitudes with spatial resolutions of 25 meters or better. In addition to the range to the surface LOLA measures the surface roughness from the spreading of the laser pulse and also the reflectance of the surface at 1064 nm. These measurements in conjunction with the altimetry will assist in the selection of future landing sites for future robotic and human missions to the Moon.

Zuber, Maria T.↗