Search NASA⌕ Search

SEARCH · Search NASA

Results for “value stacking”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46

High Efficiency Cascade Solar Cells

This report summarizes the main work performed by New Mexico State University and University of Houston on a DOE sponsored project High Efficiency Cascade Solar Cells. The main tasks of this project include materials synthesis, characterization, theoretical calculations, organic solar cell device fabrication and test. The objective of this project is to develop organic nano-electronic-based photovoltaics. Carbon nanotubes and organic conjugated polymers were used to synthesize nanocomposites as the new active semiconductor materials that were used for fabricating two device architectures: thin film coating and cascade solar cell fiber. Chemical vapor deposition technique was employed to synthesized a variety of carbon nanotubes (single-walled CNT, doubled-walled CNT, multi-walled CNT, N-doped SWCNT, DWCNT and MWCNT, and B-doped SWCNT, DWCNT and MWCNT) and a few novel carbon structures (CNT-based nanolance, nanocross and supported graphene film) that have potential applications in organic solar cells. Purification procedures were developed for removing amorphous carbons from carbon nanotubes, and a controlled oxidation method was established for partial truncation of fullerene molecules. Carbon nanotubes (DWCNT and DWCNT) were functionalized with fullerenes and dyes covalently and used to form nanocomposites with conjugated polymers. Biologically synthesized Tellurium nanotubes were used to form composite with the conjugated polymers as well, which generated the highest reported optical limiting values from composites. Several materials characterization technique including SEM/TEM, Raman, AFM, UV-vis, adsorption and EDS were employed to characterize the physical and chemical properties of the carbon nanotubes, the functionalized carbon nanotubes and the nanocomposites synthesized in this project. These techniques allowed us to have a spectroscopic and morphological control of the composite formation and to understand the materials assembled. A parallel 136-CPU Beowulf computer cluster was launched intended to be used as the main computational tool for the theoretical part of this project. The mechanism of surface carboxylation of pristine and defective carbon nanotubes were studied using the computation method. Theoretical studies of boron- and nitrogen-doped carbon nanotubes functionalized with chemical groups, and CdSe/ZnSe, ZnSe/CdSe, CdTe/ZnTe, and ZnTe/CdTe core-shell semiconductor nanoparticles embedded in electroactive polymers were also carried out. We have successfully fabricated singular champion cells with Voc of 0.6 V and Jsc of 15 mA, and developed the pixel cells and with a working areas over 25mm 2 , 2.5 % efficiency for a multicell arrangement, and a stability of 40% of their initial efficiency after 11,000 minutes. We have also demonstrated the feasibility of using a gold film as an alternative semi-transparent electrode for organic solar cell applications. An efficiency of 1.9 % (J SC of 7.01 mA/cm 2 , V OC of 0.55 V, FF of 0.49) can be reached by using the gold film as an anode instead of ITO. Two new vertical organic solar cell architectures: stack cells and wrap cells, suitable as an alternative to planar devices were developed as well. We have proved the feasibility of replacing ITO with more traditional metals without hindering performance, and developed natural encapsulation techniques during device fabrication. Optical modeling of the stack cells was also performed to enhance our understanding of this device configuration.

14 SOLAR ENERGY↗

Impact of Storage Time on the Needed Capture Efficiency for Volatile Radionuclides – 13369

During the processing of used nuclear fuel (UNF), volatile radionuclides will be discharged from the facility stack if no recovery processes are in place to limit their release. The volatile radionuclides of concern are 3 H, 14C, 85Kr, and 129I. There are three key regulations that address the release of these radionuclides to the environment — 40 CFR 61, 40 CFR 190, and 10 CFR 20. These regulations apply to the total radionuclide release and establish dose limits for the maximum exposed individual (MEI) in the public both in terms of whole body dose and dose to specific organs such as the thyroid. Each radionuclide released to the environment contributes to the total dose to some degree. In this paper we attempt to evaluate the efficiency requirements for the capture processes to limit the doses to the MEI to regulatory levels. Since the total amount of each volatile radionuclide present in the UNF changes with the age of the fuel, the respective capture requirements also change with time. Specifically, we are interested in the impact of the decreasing contribution of 3 H and 85Kr, which have relatively short half-lives, 12.32 y and 10.76 y, respectively, with the increasing age of the fuel (i.e., time between when the UNF is removed from the reactor and the time it is processed) on the capture requirements. In this paper we examine the capture requirements for these four radionuclides for three fuel types (pressurized water reactor [PWR] with uranium oxide fuel [UOX], PWR with mixed oxide fuel [MOX], and an advanced high temperature gas-cooled reactor [AHTGR]), several burnup values, and time out of reactor extending to 200 y. We calculate doses to the MEI with the EPA code CAP-88 and look at two dose contribution cases. In the first case, we assume that the total allowable dose is attributed to only the four volatile radionuclides. This establishes the lowest capture efficiency value possible. Since this is unrealistic, because it assumes zero dose contribution from all other radionuclides, we also examine a second case, where only 10% of the allowable dose is assigned to the four volatile radionuclides. We calculate the required decontamination factors (DFs) for both of these cases for the three fuel types, multiple fuel burnups, and fuel ages and determine whether or not the dose to the whole body or to the thyroid that drives the capture requirements would require additional effluent controls for the shorter half-life volatile radionuclides based on dose considerations. This analysis indicates that the principal isotopes of concern are generally 3 H and 129I, the latter requiring the highest DFs. The maximum DF value for 129I is 8000 for the evaluated cases and assumptions used.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

High Dense Gas Fraction in a Gas-rich Star-forming Galaxy at z = 1.2

We report observations of dense molecular gas in the star-forming galaxy EGS 13004291 (z = 1.197) using the Plateau de Bure Interferometer. We tentatively detect HCN and HNC J=2→1 emission when stacked together at 4σ significance, yielding line luminosities of L{sub HCN(J=2→1)}{sup ′}=(9±3)×10{sup 9} K km s{sup −1} pc{sup 2} and L{sub HNC(J=2→1)}{sup ′}=(5±2)×10{sup 9} K km s{sup −1} pc{sup 2}, respectively. We also set 3σ upper limits of <7–8 ×10{sup 9} K km s{sup −1} pc{sup 2} on the HCO{sup +}(J=2→1), H{sub 2}O(3{sub 13}→2{sub 20}), and HC{sub 3}N(J = 20 → 19) line luminosities. We serendipitously detect CO emission from two sources at z∼1.8 and z∼3.2 in the same field of view. We also detect CO(J=2→1) emission in EGS 13004291, showing that the excitation in the previously detected CO(J=3→2) line is subthermal (r{sub 32}=0.65±0.15). We find a line luminosity ratio of L{sub HCN}{sup ′}/L{sub CO}{sup ′} = 0.17 ± 0.07, as an indicator of the dense gas fraction. This is consistent with the median ratio observed in z>1 galaxies (L{sub HCN}{sup ′}/L{sub CO}{sup ′} = 0.16 ± 0.07) and nearby ULIRGs (L{sub HCN}{sup ′}/L{sub CO}{sup ′} = 0.13 ± 0.03), but higher than that in local spirals (L{sub HCN}{sup ′}/L{sub CO}{sup ′} = 0.04 ± 0.02). Although EGS 13004291 lies significantly above the galaxy main sequence at z∼1, we do not find an elevated star formation efficiency (traced by L{sub FIR}/L{sub CO}{sup ′}) as in local starbursts, but a value consistent with main-sequence galaxies. The enhanced dense gas fraction, the subthermal gas excitation, and the lower than expected star formation efficiency of the dense molecular gas in EGS 13004291 suggest that different star formation properties may prevail in high-z starbursts. Thus, using L{sub FIR}/L{sub CO}{sup ′} as a simple recipe to measure the star formation efficiency may be insufficient to describe the underlying mechanisms in dense star-forming environments inside the large gas reservoirs.

79 ASTRONOMY AND ASTROPHYSICS↗

Investigations of the crystallization mechanism of CrSb and CrSb{sub 2} multilayered films using in-situ X-ray diffraction and in-situ X-ray reflectometry

Chromium and antimony multilayered films with variable elemental layer thickness were deposited on (1 0 0)-Si substrate cooled with liquid nitrogen. The stoichiometry of the films was adjusted to Cr:Sb=1:1 and 1:2. The thickness of Cr-Sb repeating units of these multifilms was varied between 11.4 and 102.5 A. Satellite maxima in the X-ray reflectivity curves observed for films in the as-deposited state demonstrate an alternating stacking of the evaporated elements. The reactivity of the superlattice reactants was investigated with temperature dependent in-situ X-ray diffractometry and X-ray reflectometry. The crystallization temperature of CrSb depends on the double-layer thickness and is about 90 Degree-Sign C for a Cr:Sb ratio of 1:1 and double-layer thickness of 53.7 A where nucleation and crystal formation occurs at the element interfaces, while for a thin double-layer thickness (11.4 A) first interdiffusion of the elements occurs before crystallization starts, i.e., an amorphous intermediate is formed prior to crystallization of CrSb. A decomposition reaction into CrSb{sub 2} occurs at about 230 Degree-Sign C, and up to about 575 Degree-Sign C, CrSb, CrSb{sub 2} and amorphous Cr coexist. For the ratio Cr:Sb=1:2 and a thin double-layer thickness prior to crystallization of CrSb{sub 2} nano-sized crystallites with a composition near CrSb{sub 2} nucleate and grow. These crystallites are then successively transformed in long-range ordered crystals exhibiting a pronounced preferred orientation. For films with a thicker repeat unit first formation of CrSb is observed which then reacts with elemental Sb yielding crystalline CrSb{sub 2}. An activation energy for interdiffusion of Cr and Sb of about 1.8 eV is estimated for a film with Cr:Sb=1:1 exhibiting a double-layer thickness of about 53.7 A and an energy for crystal growth of about 1.1 eV. For the film with the thinner double-layer thickness of 11.4 A a lower value of the activation energy for interdiffusion is obtained. For CrSb{sub 2} the energy for crystal growth is about 3.0 eV being significantly larger than for CrSb. Specific resistivity and Hall coefficient measurements were performed for crystalline CrSb and CrSb{sub 2} films. The temperature-dependent resistivity measurement exhibits a metallic behavior for CrSb and semi-conducting properties for CrSb{sub 2}. - Graphical abstract: The compound CrSb{sub 2} crystallizes from the amorphous state via intermediate formation of CrSb. Highlights: Black-Right-Pointing-Pointer CrSb and CrSb{sub 2} crystallize at very low temperatures in multilayered films. Black-Right-Pointing-Pointer Film thickness determines crystallization at interfaces or from amorphous intermediate. Black-Right-Pointing-Pointer Prior to crystallization of CrSb{sub 2}, highly textured CrSb crystallizes first. Black-Right-Pointing-Pointer Depending on the film thickness CrSb{sub 2} exhibits different preferred orientations.

36 MATERIALS SCIENCE↗

AGR-1 Irradiated Compact 6-1-1 PIE Report: Evaluation of As-Irradiated Fuel Performance Using Leach Burn Leach, IMGA, Materialography, and X-ray Tomography

The AGR-1 irradiation test train consisted of six independently monitored capsules. All capsules contained twelve compacts in three stacks of four compacts each [Pope 2010]. Compact 6-1-1 was located in capsule 6, at the top of the test train. The compact was in stack 1 (one of the two stacks closest to the core) in position 1 (at the bottom of the 4 compact stack). Compact 6-1-1 was identified in the fabrication data package as LEU01-46T-Z32 [Hunn et al. 2006]. Details of the compact fabrication and measured properties can be found in that data package. The compact lot was made using TRISO-coated particles designated as AGR-1 Baseline fuel. These particles contained 19.7% enriched mixed uranium oxideuranium carbide (UCO) kernels with a O/U atomic ratio of ~1.36 and a C/U atomic ratio of ~0.33 [Pope 2010]. Details of the coated particle fabrication and measured properties can be found in the data package for the AGR-1 Baseline particles [Hunn and Lowden 2006]. The compact was irradiated at the INL Advanced Test Reactor (ATR) to an average calculated burn-up of 15.1% fissions per initial metal atom (FIMA) and an average calculated fast fluence of 3.0 x 10 25 n/m 2 [Sterbentz 2011] at a calculated volume averaged and time averaged temperature of approximately 1111°C [Hawkes 2012]. Capsules were disassembled and preliminary compact and graphite holder inspection was performed [Demkowicz et al. 2011]. Compact 6-1-1 was shipped to ORNL and post-irradiation examination (PIE) was performed according to examination plan PLN-3624 [Demkowicz 2010-2]. All the examination plan objectives listed below were completed except item 6, which was deleted due to limited funding. 1. Determine the inventory of fission products retained in the compact matrix, but not contained by the SiC and determine the number of exposed kernels or particles with defective SiC layers using the deconsolidation-leach-burn-leach method. 2. Gamma count all particles to quantify 137Cs inventory for comparison with calculated values and gamma spectrometric measurements made on the whole compact. Also, attempt to quantify the inventory of any other fission products for which gamma emissions are observed. 3. Characterize each particle based on the 137 Cs/ 144 Ce ratio to identify particles with low Cs retention that may be the result of a failed SiC coating. 4. Gamma count a subset of particles to determine the 110m Ag inventory for comparison with calculated values and gamma spectrometric measurements made on the whole compact. Also, attempt to quantify the inventory of other fission products observed. 5. Microscopically inspect selected particles to determine the condition of the kernels and coatings. This could include kernel migration, coating microstructures and defects, fission product attack of the SiC layer, and fission product migration in the coating layers. 6. Perform high temperature fission product release tests on a subset of particles in order to calibrate the collection efficiency of the Core Conduction Cooldown Test Facility (CCCTF) deposition cup for selected fission products. Gamma count particles before and after the heating test to quantify the released fission product fractions. 7. Archive remaining particles for later use. Compact 6-1-1 LBL began with compact deconsolidation in the Building 3525 hot cell, followed by two nitric acid leaches of the particles and matrix residue using a Soxhlet extraction apparatus. The matrix residue was then burned and the ash was leached twice with boiling nitric acid. The deconsolidated particles underwent an IMGA analysis to determine gamma-emitting isotope inventories for individual particles; the most conspicuous elements with reduced inventories, indicating fission product release, were silver and europium. During the IMGA analysis, particles with low silver were identified and a subset of these was set aside for materialography and x-ray. After the completion of the IMGA study, about 10% of the particles (421) were set aside as an archive and the remainder burned back and leached twice in the Soxhlet apparatus. Figure 1 shows a flow chart detailing the PIE of Compact 6-1-1.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermochemical and kinetic aspects of the sulfurization of Cu-Sb and Cu-Bi thin films

CuSbS{sub 2} and Cu{sub 3}BiS{sub 3} are being investigated as part of a search for new absorber materials for photovoltaic devices. Thin films of these chalcogenides were produced by conversion of stacked and co-electroplated metal precursor layers in the presence of elemental sulfur vapour. Ex-situ XRD and SEM/EDS analyses of the processed samples were employed to study the reaction sequence with the aim of achieving compact layer morphologies. A new 'Time-Temperature-Reaction' (TTR) diagram and modified Pilling-Bedworth coefficients have been introduced for the description and interpretation of the reaction kinetics. For equal processing times, the minimum temperature required for CuSbS{sub 2} to appear is substantially lower than for Cu{sub 3}BiS{sub 3}, suggesting that interdiffusion across the interfaces between the binary sulfides is a key step in the formation of the ternary compounds. The effects of the heating rate and sulfur partial pressure on the phase evolution as well as the potential losses of Sb and Bi during the processes have been investigated experimentally and the results related to the equilibrium pressure diagrams obtained via thermochemical computation. - Graphical Abstract: Example of 3D plot showing the equilibrium pressure surfaces of species potentially escaping from chalcogenide films as a function of temperature and sulfur partial pressure. Bi{sub (g)}, Bi{sub 2(g)}, and BiS{sub (g)} are the gaseous species in equilibrium with solid Bi{sub 2}S{sub 3(s)} considered in this specific example. The pressure threshold plane corresponds to the pressure limit above which the elemental losses from 1 {mu}m thick films exceeds 10% of the original content per cm{sup 2} area of film and dm{sup 3} capacity of sulfurization furnace under static atmosphere conditions. The sulfurization temperature/sulfur partial pressure boundaries required to minimise the elemental losses below a given value can be easily read from the 2D projection of the intersection curves into the T-p{sub S2} plane. Highlights: Black-Right-Pointing-Triangle Sulfurization of Sb-Cu and Bi-Cu metal precursors for thin film PV applications. Black-Right-Pointing-Triangle Kinetics shows the rate determining step to be the interdiffusion of binary sulfides. Black-Right-Pointing-Triangle Phase evolution is consistent with Pilling-Bedworth coefficients of Cu, Sb and Bi. Black-Right-Pointing-Triangle Elemental losses can be minimised via the use of equilibrium pressure diagrams.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Damage tolerance of pressurized graphite/epoxy tape cylinders under uniaxial and biaxial loading

The damage tolerance behavior of internally pressurized, axially slit, graphite/epoxy tape cylinders was investigated. Specifically, the effects of axial stress, structural anisotropy, and subcritical damage were considered. In addition, the limitations of a methodology which uses coupon fracture data to predict cylinder failure were explored. This predictive methodology was previously shown to be valid for quasi-isotropic fabric and tape cylinders but invalid for structurally anisotropic (+/-45/90)(sub s) and (+/-45/0)(sub s) cylinders. The effects of axial stress and structural anisotropy were assessed by testing tape cylinders with (90/0/+/-45)(sub s), (+/-45/90)(sub s), and (+/-45/0)(sub s) layups in a uniaxial test apparatus, specially designed and built for this work, and comparing the results to previous tests conducted in biaxial loading. Structural anisotropy effects were also investigated by testing cylinders with the quasi-isotropic (0/+/-45/90)(sub s) layup which is a stacking sequence variation of the previously tested (90/0/+/-45)(sub s) layup with higher D(sub 16) and D(sub 26) terms but comparable D(sub 16) and D(sub 26) to D(sub 11) ratios. All cylinders tested and used for comparison are made from AS4/3501-6 graphite/epoxy tape and have a diameter of 305 mm. Cylinder slit lengths range from 12.7 to 50.8 mm. Failure pressures are lower for the uniaxially loaded cylinders in all cases. The smallest percent failure pressure decreases are observed for the (+/-45/90)(sub s) cylinders, while the greatest such decreases are observed for the (+/-45/0)(sub s) cylinders. The relative effects of the axial stress on the cylinder failure pressures do not correlate with the degree of structural coupling. The predictive methodology is not applicable for uniaxially loaded (+/-45/90)(sub s) and (+/-45/0)(sub s) cylinders, may be applicable for uniaxially loaded (90/0/+/-45)(sub s) cylinders, and is applicable for the biaxially loaded (90/0/+/-45)(sub s) and (0/+/-45/90)(sub s) cylinders. This indicates that the ratios of D(sub 16) and D(sub 26) to D(sub 11), as opposed to the absolute magnitudes of D(sub 16) and D(sub 26), may be important in the failure of these cylinders and in the applicability of the methodology. Discontinuities observed in the slit tip hoop strains for all the cylinders tested indicate that subcritical damage can play an important role in the failure of tape cylinders. This role varies with layup and loading condition and is likely coupled to the effects of structural anisotropy. Biaxial failure pressures may exceed the uniaxial values because the axial stress contributes to the formation of 0 deg ply splitting (accompanied by delamination) or similar stress-mitigating subcritical damage. The failure behavior of similar cylinders can also vary as a result of differences in the role of subcritical damage as observed for the case of a biaxially loaded (90/0/+/-45)(sub s) cylinder with a 12.7 mm slit. For this case, the methodology is valid when the initial coupon and cylinder fracture modes agree. However, the methodology underpredicts the failure pressure of the cylinder when a circumferential fracture path, suggestive of a 0 deg ply split, occurs at one slit tip. Thus, the failure behavior of some tape cylinders may be highly sensitive to the initial subcritical damage mechanism. Finite element analyses are recommended to determine how structural anisotropy and axial stress modify the slit tip stress states in cylinders from those found in flat plates since similarity of these stress states is a fundamental assumption of the current predictive methodology.

Priest, Stacy Marie↗

Integrated Bosch Process System Models for In-Situ Oxygen and Carbon Production

In-Situ Resource Utilization (ISRU) technology is a vital component to NASA’s mission of a sustainable presence on the Moon and Mars. Local resources can be leveraged to reduce resupply frequency and mass. Elements of the Bosch process, combined with the carbothermal reduction process, can produce oxygen on the lunar surface with minimal consumables. The Bosch process can also produce oxygen on the Martian surface by using the CO 2 -rich environment. Between both systems, adsorption pump, solar thermal energy, carbon formation reactor, and water recovery subsystems are modeled and integrated to create a functional model in MATLAB software. The model is used to simulate performance of the system and reduce mass, power, and volume requirements. This integrated system model provides a tool to scale ISRU technologies for oxygen and carbon production. The MATLAB model is created by developing a system of independent subsystem models that are solved for their quasi-steady state values which can be integrated with respect to time to determine the change in current states. A flexible time stepping method is used to ensure a high level of accuracy during periods of rapid change while still making use of a simple explicit integration method. The flexible time step is calculated for each independent subsystem and the minimum value from those is used as the overall time step. A flexible time step is calculated by dividing a resolution value, or the maximum change per time step, by the variables current rate of change. The maximum value from all points in space is used for subsystem models that contain multiple values. The process is done for every variable that is being monitored in each subsystem and the global minimum is used as that iteration’s timestep. Several assumptions used in the MATLAB model for fluid flow dynamics, such as 1-D gas flow through the sorption pump, are supported by modeling in Ansys Fluent software. The Lunar oxygen production system is outlined in Fig. 1. The carbothermal reduction subsystem uses solar energy to heat a mixture of lunar regolith and carbon powder to produce carbon monoxide. To begin, the carbon monoxide feeds to the modified Bosch subsystem along with hydrogen gas. The reactants then enter the carbon formation reactor where water and carbon powder are produced. Solar thermal energy is used to add energy to the reactor, but waste heat from the carbothermal process is another potential heat source. The water is collected and electrolyzed to produce hydrogen which reenters the Bosch subsystem, and the oxygen is stored for downstream use. The carbon powder is collected and feeds back into the carbothermal subsystem. The Martian oxygen production system uses the full Bosch process and is outlined in Fig 2. A CO 2 adsorption pump thermally cycles to scrub and pressurize CO 2 from the environment. Along with an initial supply of hydrogen, the reactants enter the Reverse Water Gas Shift Reactor (RWGSR) which produces carbon monoxide and water. Carbon monoxide and unreacted hydrogen enter the carbon formation reactor to produce water and carbon powder. The water is collected from both reactors and electrolyzed to reintroduce hydrogen and store oxygen for propellant production or life support. Carbon is removed from the carbon formation reactor and stored. The adsorption pump utilizes rapid cycle temperature swings within a stack of zeolite coated surfaces. The subsystem model solves 1-D quasi-steady conservation laws of the quasi-steady form, shown in Eq. 1, for the gas stream and heat exchange liquid to predict performance parameters such as breakthrough capacity and optimum cycle time. The source term S is used to capture interactions between the fluid flows and the sorbent. A quasi-steady-state scheme is used where no time derivatives appear in the governing equations, except for those in the source terms. This results in an autonomous system, where ∂F/∂x = ƒ(F). The fluxes F are provided at the inlet, and an explicit method is used to solve for the spatial distribution of F. The heat and mass flows to the sorbent are then extracted from the source terms. These flows are numerically integrated to produce a 1-D solution for the system’s state as a function of both time and space. The body of the adsorption pump is separated into two semi-independent models: the heat exchanger fluid flow and gas flow through the zeolite coated surfaces. Both models are solved using the above-described method to find a 1-D solution as a function of space and interact only once a timestep is taken. The interaction point is the sorbent through which all heat transfer between the two models must occur. Sorbent mass adsorption is calculated using the Lagergren model, shown in Eq. 2, where the transfer coefficient, λ D , is found by solving a system of nondimensionalized equations derived by using the heat and mass transfer analogy for transport phenomena. Using Grade 544 Type 13X zeolite as the sorbent material, the equilibrium concentration, θ eq , is calculated using the k-site Langmuir isotherm and fit parameters. Additionally, the enthalpy of adsorption used in the model is computed by interpolation of available data [1]. The subsystem model was validated using the Rapid Cycle Temperature Swing Adsorption (RC-TSA) pump. The solar thermal energy subsystem focuses on a solar concentrator concept with a heat exchanger to heat the reactants before entering the carbon formation reactor. The subsystem model assumes a fixed solar flux and reflector efficiency to calculate the reactant temperature given the incoming temperature, pressure, and exchanger geometry. The receiver is a custom manufactured series of copper blocks with serpentine channels to increase its surface area and the residence time of the reactants to heat up to 550 °C. The subsystem model was validated using a heat exchanger developed at NASA Glenn Research Center (GRC). The solar thermal energy subsystem focuses on a solar concentrator concept with a heat exchanger to heat the reactants before entering the carbon formation reactor. The subsystem model assumes a fixed solar flux and reflector efficiency to calculate the reactant temperature given the incoming temperature, pressure, and exchanger geometry. The receiver is a custom manufactured series of copper blocks with serpentine channels to increase its surface area and the residence time of the reactants to heat up to 550 °C. The subsystem model was validated using a heat exchanger developed at NASA Glenn Research Center (GRC).

In situ Resource Utilization↗

Molecular Structure of Adsorbed Water Phases in Silica Nanopores

The adsorption of water vapor in silica nanopores with different pore morphologies and surface hydrophilicities was studied to quantify the densities and thicknesses of the water sorption layers and deduce their molecular structures. Water adsorption to surface hydroxyls is described by a multilayer sorption model. At low pressure, the water adsorption isotherms are largely independent of pore size and the adsorbed amounts scale with the surface hydroxyl density. Adsorbed-phase densities corresponding to the adsorption of two water molecules per surface hydroxyl group are found in the first adsorbed water layer for a wide range of surface hydroxyl densities. The densities and layer thickness values found in narrow pores indicate that patchy adsorbed layers form if not enough water molecules exist for a full layer, which coexist with dry pore surface regions. This behavior indicates cooperative adsorption effects, i.e., a preference for the formation of hydrogen bonds between water molecules bound to surface hydroxyls. In narrow pores, pore condensation limits further growth of the sorption layer, and in larger pores and at the planar quartz surface, a second adsorbed water layer is formed, which can hold up to approximately 4 additional water molecules per surface hydroxyl group. The water molecules in these thicker adsorption layers arrange such that the sorption layer density is similar to the bulk water density. Pore confinement limitations on the sorption layers are observed in pores with radii of as large as 8 nm. Molecular dynamics modeling reveals two preferential orientations for water molecules adsorbing to surface hydroxyl groups and suggests an intralayer structuring in the adsorbed monolayer. Furthermore, adsorbed water molecules in the sorption layer are bonded to the surface hydroxyl group via the donation and acceptance of hydrogen bonds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Scoping Study for Fast Flux Testing in the Advanced Test Reactor

The value of fast spectrum reactors remains prominent in the nuclear technology portfolio. The performance of these reactors can be maximized with advancements in nuclear fuel technologies, but development of these technologies is currently held back by lack of fast spectrum test reactors available to the United States. Spectral modification of experiment positions in the thermal spectrum Advanced Test Reactor (ATR) has long been used to support fast reactor fuel development, but these methods have not been progressed to their full potential. This study investigated the use of concentric rings of aluminum-clad fuel plates in ATR flux traps and thermal neutron absorbing filters to increase fast neutron flux on test specimens. This concept was termed the Boosted Energy Advanced Spectrum Test (BEAST). This approach will enable irradiation of advanced fuel designs in prototypic-length fuel pins and representative flux environment to support post irradiation exams, enable transient testing, and produce the type of data that will permit lead test assembly irradiations in true Sodium Fast Reactors (SFRs) when they become available. Neutronic predictions were performed to investigate BEAST design options and thermal hydraulic models were produced to ensure feasibility of BEAST. Two versions were considered based on the geometric limitations of ATR’s small and large flux traps. The small version was found to be preferable due to slightly higher fast flux and fast-to-thermal neutron ratio. Perhaps more influentially, the small flux trap option was also preferred to avoid conflict with ongoing very high temperature reactor fuel irradiation programs in ATR’s large northeast flux trap. The small flux trap option provided less than half the test volume of the large version, but still had adequate volume for seven SFR pins in cross section which could be stacked two-high in ATR’s 1.2m long core to accommodate up to 14 EBR-II size pins. The preference for the small flux trap configuration should be revisited if additional collaborative test programs emerge with the need to irradiate a significant volume of additional specimens. Calculations were performed regarding a lithium deuteride ring to convert thermal neutrons into 14 MeV fusion neutrons. At the time this report was written these calculations were partially complete and it remains to be seen whether the concept would be worth including in BEAST. Given the preference for the small flux trap option, which does not afford enough room for the 14 MeV ring, it was concluded to defer future work on the lithium deuteride ring. This decision could be revisited if fusion material research programs emerge for collaborative testing in BEAST. A cadmium-lined specimen holder design was found to be adequate in filtering thermal neutrons and preferred over other neutron absorbers based on past experience with cadmium baskets. It was acknowledged that cadmium-bearing hardware would become depleted and need to be replaced occasionally, which appeared feasible from a mechanical design perspective. Neutronic studies investigated different enrichment levels in the booster fuel using uranium-molybdenum alloy dispersion fuel which has performed well in past ATR irradiations. Both options were able to drive fuel pins to SFR-like fission heating rates. The high enriched booster fuel option outperformed the low enriched option by ~20% on key metrics including fast flux and fast-to-thermal ratio, but the low enriched option was favored in order to broaden options for potential fuel suppliers. The preferred BEAST design options including cadmium filter with low enriched booster fuel in the small flux trap configuration was predicted to achieve 6.2E14 n/cm2sec fast flux (>0.1 MeV) with a fast-to-thermal ratio of 44.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TEMPORAL CORRELATIONS BETWEEN OPTICAL AND GAMMA-RAY ACTIVITY IN BLAZARS

We have been using the 0.76 m Katzman Automatic Imaging Telescope (KAIT) at Lick Observatory to optically monitor a sample of 157 blazars that are bright in gamma-rays being detected with high significance (≥10σ) in one year by the Large Area Telescope (LAT) on the Fermi Gamma-ray Space Telescope. We attempt to observe each source on a three-day cadence with KAIT, subject to weather and seasonal visibility. The gamma-ray coverage is essentially continuous. KAIT observations extend over much of the five-year Fermi mission for several objects, and most have >100 optical measurements spanning the last three years. These blazars (flat-spectrum radio quasars and BL Lac objects) exhibit a wide range of flaring behavior. Using the discrete correlation function (DCF), here we search for temporal relationships between optical and gamma-ray light curves in the 40 brightest sources in hopes of placing constraints on blazar acceleration and emission zones. We find strong optical-gamma-ray correlation in many of these sources at time delays of ∼1 to ∼10 days, ranging between –40 and +30 days. A stacked average DCF of the 40 sources verifies this correlation trend, with a peak above 99% significance indicating a characteristic time delay consistent with 0 days. These findings strongly support the widely accepted leptonic models of blazar emission. However, we also find examples of apparently uncorrelated flares (optical flares with no gamma-ray counterpart and gamma-ray flares with no optical counterpart) that challenge simple, one-zone models of blazar emission. Moreover, we find that flat-spectrum radio quasars tend to have gamma-rays leading the optical, while intermediate- and high-synchrotron peak blazars with the most significant peaks have smaller lags/leads. It is clear that long-term monitoring at high cadence is necessary to reveal the underlying physical correlation.

79 ASTRONOMY AND ASTROPHYSICS↗

Final Report for CCS Cross-Layer Reliability Visioning Study

The geometric rate of improvement of transistor size and integrated circuit performance known as Moore's Law has been an engine of growth for our economy, enabling new products and services, creating new value and wealth, increasing safety, and removing menial tasks from our daily lives. Affordable, highly integrated components have enabled both life-saving technologies and rich entertainment applications. Anti-lock brakes, insulin monitors, and GPS-enabled emergency response systems save lives. Cell phones, internet appliances, virtual worlds, realistic video games, and mp3 players enrich our lives and connect us together. Over the past 40 years of silicon scaling, the increasing capabilities of inexpensive computation have transformed our society through automation and ubiquitous communications. Looking forward, increasing unpredictability threatens our ability to continue scaling integrated circuits at Moore's Law rates. As the transistors and wires that make up integrated circuits become smaller, they display both greater differences in behavior among devices designed to be identical and greater vulnerability to transient and permanent faults. Conventional design techniques expend energy to tolerate this unpredictability by adding safety margins to a circuit's operating voltage, clock frequency or charge stored per bit. However, the rising energy costs needed to compensate for increasing unpredictability are rapidly becoming unacceptable in today's environment where power consumption is often the limiting factor on integrated circuit performance and energy efficiency is a national concern. Reliability and energy consumption are both reaching key inflection points that, together, threaten to reduce or end the benefits of feature size reduction. To continue beneficial scaling, we must use a cross-layer, Jull-system-design approach to reliability. Unlike current systems, which charge every device a substantial energy tax in order to guarantee correct operation in spite of rare events, such as one high-threshold transistor in a billion or one erroneous gate evaluation in an hour of computation, cross-layer reliability schemes make reliability management a cooperative effort across the system stack, sharing information across layers so that they only expend energy on reliability when an error actually occurs. Figure 1 illustrates an example of such a system that uses a combination of information from the application and cheap architecture-level techniques to detect errors. When an error occurs, mechanisms at higher levels in the stack correct the error, efficiently delivering correct operation to the user in spite of errors at the device or circuit levels. In the realms of memory and communication, engineers have a long history of success in tolerating unpredictable effects such as fabrication variability, transient upsets, and lifetime wear using information sharing, limited redundancy, and cross-layer approaches that anticipate, accommodate, and suppress errors. Networks use a combination of hardware and software to guarantee end-toend correctness. Error-detection and correction codes use additional information to correct the most common errors, single-bit transmission errors. When errors occur that cannot be corrected by these codes, the network protocol requests re-transmission of one or more packets until the correct data is received. Similarly, computer memory systems exploit a cross-layer division of labor to achieve high performance with modest hardware. Rather than demanding that hardware alone provide the virtual memory abstraction, software page-fault and TLB-miss handlers allow a modest piece of hardware, the TLB, to handle the common-case operations on a cyc1e-by-cycle basis while infrequent misses are handled in system software. Unfortunately, mitigating logic errors is not as simple or as well researched as memory or communication systems. This lack of understanding has led to very expensive solutions. For example, triple-modular redundancy masks errors by triplicating computations in either time or area. This mitigation methods imposes a 200% increase in energy consumption for every operation, not just the uncommon failure cases. At a time when computation is rapidly becoming part of our critical civilian and military infrastructure and decreasing costsfor computation are fueling our economy and our well being, we cannot afford increasingly unreliable electronics or a stagnation in capabilities per dollar, watt, or cubic meter. If researchers are able to develop techniques that tolerate the growing unpredictability of silicon devices, Moore's Law scaling should continue until at least 2022. During this 12-year time period, transistors, which are the building blocks of electronic devices, will scale their dimensions (feature sizes) from 45nm to 4.5nm.

99 GENERAL AND MISCELLANEOUS↗

Multi-scale characterization of pore evolution in a combustion metamorphic complex, Hatrurim basin, Israel: Combining (ultra) small-angle neutron scattering and image analysis

Backscattered scanning electron micrograph and ultra small- and small-angle neutron scattering data have been combined to provide statistically meaningful data on the pore/grain structure and pore evolution of combustion metamorphic complexes from the Hatrurim basin, Israel. Three processes, anti-sintering roughening, alteration of protolith (dehydration, decarbonation, and oxidation) and crystallization of high-temperature minerals, occurred simultaneously, leading to significant changes in observed pore/grain structures. Pore structures in the protoliths, and in lowand high-grade metamorphic rocks show surface (Ds) and mass (Dm) pore fractal geometries with gradual increases in both Ds and Dm values as a function of metamorphic grade. This suggests that increases in pore volume and formation of less branching pore networks are accompanied by a roughening of pore/grain interfaces. Additionally, pore evolution during combustion metamorphism is also characterized by reduced contributions from small-scale pores to the cumulative porosity in the high-grade rocks. At high temperatures, small-scale pores may be preferentially closed by the formation of high-temperature minerals, producing a rougher morphology with increasing temperature. Alternatively, large-scale pores may develop at the expense of small-scale pores. These observations (pore fractal geometry and cumulative porosity) indicate that the evolution of pore/grain structures is correlated with the growth of high-temperature phases and is a consequence of the energy balance between pore/grain surface energy and energy arising from heterogeneous phase contacts. The apparent pore volume density further suggests that the localized time/temperature development of the high-grade Hatrurim rocks is not simply an extension of that of the low-grade rocks. The former likely represents the "hot spots (burning foci)" in the overall metamorphic terrain while the latter may represent contact aureoles.

Wang, Hsiu-Wen↗

Shuffling mode competition leads to directionally anisotropic mobility of faceted Σ11 boundaries in fcc metals

Faceted grain boundaries can migrate in interesting and unexpected ways. For example, faceted Σ11 <110> tilt grain boundaries were observed to exhibit mobility values that could be strongly dependent on the direction of migration. In order to understand whether this directionally-anisotropic mobility is a general phenomenon and to isolate mechanistic explanations for this behavior, molecular dynamics simulations of bicrystals evolved under an artificial driving force are used to study interface migration for a range of boundary plane inclination angles and temperatures in multiple face centered cubic metals (Al, Ni, and Cu). We find that directionally anisotropic mobility is active in a large fraction of these boundaries in Ni and Cu and should therefore impact the coarsening of polycrystalline materials. On the other hand, no such anisotropy is observed in any of the Al boundaries, showing that this behavior is material-dependent. Migration of the faceted boundaries is accomplished through transformation events at facet nodes and incommensurate boundary plane facets, which are termed shuffling modes. Three major shuffling modes have been identified, namely Shockley shuffling, slip plane shuffling, and disordered shuffling. A shift from the first two ordered modes to the third disordered mode is found to be responsible for reducing or removing directionally-anisotropic mobility, especially at the highest temperatures studied.

36 MATERIALS SCIENCE↗

The Ares I-1 Flight Test--Paving the Road for the Ares I Crew Launch Vehicle

In accordance with the U.S. Vision for Space Exploration and the nation's desire to again send humans to explore beyond Earth orbit, NASA has been tasked to send human beings to the moon, Mars, and beyond. It has been 30 years since the United States last designed and built a human-rated launch vehicle. NASA is now building the Ares I crew launch vehicle, which will loft the Orion crew exploration vehicle into orbit, and the Ares V cargo launch vehicle, which will launch the Lunar Surface Access Module and Earth departure stage to rendezvous Orion for missions to the moon. NASA has marshaled unique resources from the government and private sectors to perform the technically and programmatically complex work of delivering astronauts to orbit early next decade, followed by heavy cargo late next decade. Our experiences with Saturn and the Shuttle have taught us the value of adhering to sound systems engineering, such as the "test as you fly" principle, while applying aerospace best practices and lessons learned. If we are to fly humans safely aboard a launch vehicle, we must employ a variety of methodologies to reduce the technical, schedule, and cost risks inherent in the complex business of space transportation. During the Saturn development effort, NASA conducted multiple demonstration and verification flight tests to prove technology in its operating environment before relying upon it for human spaceflight. Less testing on the integrated Shuttle system did not reduce cost or schedule. NASA plans a progressive series of demonstration (ascent), verification (orbital), and mission flight tests to supplement ground research and high-altitude subsystem testing with real-world data, factoring the results of each test into the next one. In this way, sophisticated analytical models and tools, many of which were not available during Saturn and Shuttle, will be calibrated and we will gain confidence in their predictions, as we gain hands-on experience in operating the first of two new launch vehicle systems. The Ares I-1 flight test vehicle (FTV) will incorporate a mix of flight and mockup hardware, reflecting a configuration similar in mass, weight, and shape (outer mold line or OML) to the operational vehicle. It will be powered by a four-segment reusable solid rocket booster (RSRB), which is currently in Shuttle inventory, and will be modified to include a fifth, inert segment that makes it approximately the same size and weight as the five segment RSRB, which will be available for the second flight test in 2012. The Ares I-1 vehicle configuration is shown. Each test flight has specific objectives appropriate to the design analysis cycle in progress. The Ares I-1 demonstration test, slated for April 2009, gives NASA its first opportunity to gather critical data about the flight dynamics of the integrated launch vehicle stack, understand how to control its roll during flight, and other characterize the severe stage separation environment that the upper stage will experience during future operational flights. NASA also will begin the process of modifying the launch infrastructure and fine-tuning ground and mission operational scenarios, as NASA transitions from the Shuttle to the Ares/Orion system.

Davis, Stephan R.↗

In situ recording of Mars soundscape

Abstract Before the Perseverance rover landing, the acoustic environment of Mars was unknown. Models predicted that: (1) atmospheric turbulence changes at centimetre scales or smaller at the point where molecular viscosity converts kinetic energy into heat 1 , (2) the speed of sound varies at the surface with frequency 2,3 and (3) high-frequency waves are strongly attenuated with distance in CO 2 (refs. 2–4 ). However, theoretical models were uncertain because of a lack of experimental data at low pressure and the difficulty to characterize turbulence or attenuation in a closed environment. Here, using Perseverance microphone recordings, we present the first characterization of the acoustic environment on Mars and pressure fluctuations in the audible range and beyond, from 20 Hz to 50 kHz. We find that atmospheric sounds extend measurements of pressure variations down to 1,000 times smaller scales than ever observed before, showing a dissipative regime extending over five orders of magnitude in energy. Using point sources of sound (Ingenuity rotorcraft, laser-induced sparks), we highlight two distinct values for the speed of sound that are about 10 m s −1 apart below and above 240 Hz, a unique characteristic of low-pressure CO 2 -dominated atmosphere. We also provide the acoustic attenuation with distance above 2 kHz, allowing us to explain the large contribution of the CO 2 vibrational relaxation in the audible range. These results establish a ground truth for the modelling of acoustic processes, which is critical for studies in atmospheres such as those of Mars and Venus.

79 ASTRONOMY AND ASTROPHYSICS↗

Searching for Faint X-Ray Emission from Galactic Stellar Wind Bow Shocks

We present a stacking analysis of 2.61 Ms of archival Chandra observations of stellar wind bow shocks. We place an upper limit on the X-ray luminosity of infrared-detected bow shocks of <2 × 10{sup 29} erg s{sup −1}, a more stringent constraint than has been found in previous archival studies and dedicated observing campaigns of nearby bow shocks. We compare the X-ray luminosities and L {sub X}/L {sub bol} ratios of bow shock driving stars to those of other OB stars within the Chandra field of view. Driving stars are, on average, of later spectral type than the field-of-view OB stars, and we do not observe any unambiguously high L {sub X}/L {sub bol} ratios indicative of magnetic stars in our sample. We additionally assess the feasibility of detecting X-rays from stellar wind bow shocks with the proposed Lynx X-ray Observatory. If the X-ray flux originating from the bow shocks is just below our Chandra detection limit, the nearest bow shock in our sample (at ∼0.4 kpc with an absorbing column of ∼10{sup 21} cm{sup −2}) should be observable with Lynx in exposure times on the order of ∼100 ks.

79 ASTRONOMY AND ASTROPHYSICS↗

The Scientific Value of Collecting Samples From the Jezero Crater Rim

The Mars 2020 mission has been conducting ground-based investigation of the geology, habitability, and biosignature preservation potential and collecting samples for return to Earth in Jezero crater, Mars for nearly 3 years. Analysis of these samples will address outstanding questions in Mars science including potential habitability and how and why the climate the interior of the planet evolved through time. As of December 2023, samples of 4 igneous rocks of the Jezero crater floor and 9 sedimentary rocks of the Jezero fan and inner margin, remain on the rover. 15 tubes remain to be filled to enhance the diversity of the cache and broaden the scope of the science questions that can be addressed with returned sample studies. The next step in the mission is to explore the Jezero crater rim. It will be imperative to investigate and sample the diversity of crater rim rocks because they represent materials from Mars’ most ancient crust older than those sampled in Jezero crater, a diversity of geologic processes, and potential ancient habitable environments that have not yet been investigated or sampled. Ongoing mapping efforts are using orbiter data and long-distance images from Perseverance to identify and interpret the geologic context of the crater rim. Building on this effort and the broader geologic context for the crater rim put forward by previous studies, we identify diverse targets for in situ investigation and potential sampling by Mars 2020.

Mars sample return↗