Search NASA⌕ Search

SEARCH · Search NASA

Results for “Component amounts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Commissioning of the Delta Polarizing Undulator at LCLS

The Linac Coherent Light Source (LCLS) generates linearly polarized, intense, high-brightness x-ray pulses from planar fixed-gap undulators. While the fixed-gap design supports a very successful and tightly controlled alignment concept, it provides only limited taper capability (up to 1% through canted pole and horizontal position adjustability) and lacks polarization control. The latter is of great importance for soft x-ray experiments. A new 3.2-m-long compact undulator (based on the Cornell University Delta design) has been developed and installed in place of the last LCLS undulator segment (U33) in October 2014. This undulator provides full control of the polarization degree and K value. Used on its own, it produces fully polarized radiation in the selected state (linear, circular or elliptical) but at low intensity. To increase the output power by orders of magnitude, the electron beam is micro-bunched by several (~10) of the upstream LCLS undulator segments operated in the linear FEL regime. As unavoidable by-product, this microbunching process produces moderate amounts of horizontally linear polarized radiation which mixes with the radiation produced by the Delta undulator. This unwanted radiation component has been greatly reduced by the reverse taper configuration, as suggested by E. Schneidmiller and M. Yurkov. Full elimination of the linear polarized component was achieved through spatial separation combined with transverse collimation. The paper describes these and other methods tested during commissioning. It also presents results of polarization measurements showing high degrees of circular polarization in the soft x-ray wavelength range (500 eV - 1500 eV).

43 PARTICLE ACCELERATORS↗

Lithium sulfur batteries and electrolytes and sulfur cathodes thereof

Lithium sulfur battery cells that use water as an electrolyte solvent provide significant cost reductions. Electrolytes for the battery cells may include water solvent for maintaining electroactive sulfur species in solution during cell discharge and a sufficient amount of a cycle life-enhancing compound that facilitates charging at the cathode. The combination of these two components enhances one or more of the following cell attributes: energy density, power density and cycle life. For instance, in applications where cost per Watt-Hour (Wh) is paramount, such as grid storage and traction applications, the use of an aqueous electrolyte in combination with inexpensive sulfur as the cathode active material can be a key enabler for the utility and automotive industries, for example, providing a cost effective and compact solution for load leveling, electric vehicles and renewable energy storage. Sulfur cathodes, and methods of fabricating lithium sulfur cells, in particular for loading lithium sulfide into the cathode structures, provide further advantages.

25 ENERGY STORAGE↗

ROBIN (RuciO/BIgData Express/SENSE) A Next-Generation High-Performance Data Service Platform

Increasingly, scientific research discoverydepends on the analysis of extremely large amounts of data. Thisdata is gathered through very large scientific instruments, verylarge numbers of small devices, and mid-scale instruments.These devices generate exponentially increasing volumes of data.Such data is often obtained, analyzed, stored, visualized, andtransferred at and among sites world-wide by largecollaborations of science communities. Managing and movingextremely large volumes of data across today’s networks is aspecial multidimensional challenge. Also, existing datamanagement and movement services and tools often areinadequate to address all specific requirements. This paperdescribes the various components of this challenge and howthose issues can be addressed by ROBIN, a uniquecomprehensive set of integrated services designed specificallyfor managing and moving extremely large amounts of data overlong distances, e.g., thousands of miles around the globe. Thispaper also describes the results of initial experiments using thatset of integrated services.

Wu, Wenji↗

Chemical compatibility issues associated with use of SiC/SiC in advanced reactor concepts

Silicon carbide/silicon carbide (SiC/SiC) composites are of interest for components that will experience high radiation fields in the High Temperature Gas Cooled Reactor (HTGR), the Very High Temperature Reactor (VHTR), the Sodium Fast Reactor (SFR), or the Fluoride-cooled High-temperature Reactor (FHR). In all of the reactor systems considered, reactions of SiC/SiC composites with the constituents of the coolant determine suitability of materials of construction. The material of interest is nuclear grade SiC/SiC composites, which consist of a SiC matrix [high-purity, chemical vapor deposition (CVD) SiC or liquid phase-sintered SiC that is crystalline beta-phase SiC containing small amounts of alumina-yttria impurity], a pyrolytic carbon interphase, and somewhat impure yet crystalline beta-phase SiC fibers. The interphase and fiber components may or may not be exposed, at least initially, to the reactor coolant. The chemical compatibility of SiC/SiC composites in the three reactor environments is highly dependent on thermodynamic stability with the pure coolant, and on reactions with impurities present in the environment including any ingress of oxygen and moisture. In general, there is a dearth of information on the performance of SiC in these environments. While there is little to no excess Si present in the new SiC/SiC composites, the reaction of Si with O 2 cannot be ignored, especially for the FHR, in which environment the product, SiO 2 , can be readily removed by the fluoride salt. In all systems, reaction of the carbon interphase layer with oxygen is possible especially under abnormal conditions such as loss of coolant (resulting in increased temperature), and air and/ or steam ingress. A global outline of an approach to resolving SiC/SiC chemical compatibility concerns with the environments of the three reactors is presented along with ideas to quickly determine the baseline compatibility performance of SiC/SiC.

FHR↗

IMPACT OF URANIUM AND THORIUM ON HIGH TIO2 CONCENTRATION NUCLEAR WASTE GLASSES

This study focused on the potential impacts of the addition of Crystalline Silicotitanate (CST) and Monosodium Titanate (MST) from the Small Column Ion Exchange (SCIX) process on the Defense Waste Processing Facility (DWPF) glass waste form and the applicability of the DWPF process control models. MST from the Salt Waste Processing Facility (SWPF) is also considered in the study. The KT08-series of glasses was designed to evaluate any impacts of the inclusion of uranium and thorium in glasses containing the SCIX components. All but one of the study glasses were found to be amorphous by X-ray diffraction (XRD). One of the slowly cooled glasses contained a small amount of trevorite, which is typically found in DWPF-type glasses and had no practical impact on the durability of the glass. The measured Product Consistency Test (PCT) responses for the study glasses and the viscosities of the glasses were well predicted by the current DWPF models. No unexpected issues were encountered when uranium and thorium were added to the glasses with SCIX components.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Systematic Destruction of Electronic Parts for Aid in Electronic Failure Analysis

NASA analyzes electrical, electronic, and electromechanical (EEE) parts used in space vehicles to understand failure modes of these components. Operational amplifiers and transistors are two examples of EEE parts critical to NASA missions that can fail due to electrical overstress (EOS). EOS is the result of voltage or current over time conditions that exceeds a component s specification limit. The objective of this study was to provide known voltage pulses over well-defined time intervals to determine the type and extent of damage imparted to the device. The amount of current was not controlled but measured so that pulse energy was determined. The damage was ascertained electrically using curve trace plots and optically using various metallographic techniques. The resulting data can be used to build a database of physical evidence to compare to damaged components removed from flight avionics. The comparison will provide the avionics failure analyst necessary information about voltage and times that caused flight or test failures when no other electrical data is available.

Decker, S. E.↗

The influence of subhaloes on host halo properties

Within the ΛCDM cosmology, dark matter haloes are composed of both a smooth component and a population of smaller gravitationally bound subhaloes. These components are often treated as a single halo when properties, such as density profiles, are extracted from simulations. Recent work has shown that density profiles change substantially when subhalo mass is excluded. In this paper, we expand on this result by analysing three specific host halo properties – concentration (cNFW), spin (λB), and shape (c/a) – when calculated only from the smooth component of the halo. This analysis is performed on both Milky Way-mass haloes and cluster-mass haloes in high-resolution zoom-in N-body simulations. We find that when subhaloes are excluded, the median value of (1) cNFW is enhanced by $\approx 30\pm 11$ and $\approx 77\pm 8.1~{{\ \rm per\ cent}}$ for Milky Way-mass ($10^{12.1}\, \text{M}_\odot$) and cluster-mass ($10^{14.8}\, \text{M}_\odot$) haloes, respectively, (2) λB is reduced for Milky Way-mass by $\approx 11\pm 4.9~{{\ \rm per\ cent}}$ and cluster-mass haloes by $\approx 27\pm 3.5~{{\ \rm per\ cent}}$. Additionally, with the removal of subhaloes, cluster-mass haloes tend to become more spherical as the ratio of minor-to-major axis, c/a, increases by $\approx 11\pm 3.6~{{\ \rm per\ cent}}$, whereas Milky Way-mass haloes remain approximately the same shape with c/a changed by $\approx 1.0\pm 5.8~{{\ \rm per\ cent}}$. Fractional changes of each of these properties depend primarily on the amount of mass in subhaloes and, to a lesser extent, mass accretion history. Our findings demonstrate that the properties of the smooth components of dark matter haloes are biased relative to the total halo mass.

79 ASTRONOMY AND ASTROPHYSICS↗

Real-Time Principal-Component Analysis

A recently written computer program implements dominant-element-based gradient descent and dynamic initial learning rate (DOGEDYN), which was described in Method of Real-Time Principal-Component Analysis (NPO-40034) NASA Tech Briefs, Vol. 29, No. 1 (January 2005), page 59. To recapitulate: DOGEDYN is a method of sequential principal-component analysis (PCA) suitable for such applications as data compression and extraction of features from sets of data. In DOGEDYN, input data are represented as a sequence of vectors acquired at sampling times. The learning algorithm in DOGEDYN involves sequential extraction of principal vectors by means of a gradient descent in which only the dominant element is used at each iteration. Each iteration includes updating of elements of a weight matrix by amounts proportional to a dynamic initial learning rate chosen to increase the rate of convergence by compensating for the energy lost through the previous extraction of principal components. In comparison with a prior method of gradient-descent-based sequential PCA, DOGEDYN involves less computation and offers a greater rate of learning convergence. The sequential DOGEDYN computations require less memory than would parallel computations for the same purpose. The DOGEDYN software can be executed on a personal computer.

Duong, Vu↗

Antiprotons in cosmic rays and their implications

A brief description of the experiments carried out so far to measure the energy spectrum of antiprotons is made and the reason for the excitement in this field of research is elucidated. The observed spectrum appears to be different form the other components of cosmic rays. Various physical processes by which antiprotons could be created are summarized. The equilibrium spectrum of antiprotons in the Galaxy, arising from each of these processes, is derived for different propagation models. It is shown that no single model can predict correctly the observed data over the entire energy region. However, the recent data at low energies suggest that the conventional models with large amount of matter traversal by cosmic rays, either in the source region or during propagation, can reproduce the data closely. The implications of these propagation models for other components are discussed and the need for more observations is emphasized.

Stephens, S. A.↗

Additive Manufactured Materials Studies

The production of additively manufactured (AM) materials, is a growing technology that potentially offers more cost effective ways to produce metallic components for various uses. Mechanical properties of some AM metals have been studied, but more work is needed to better understand their dynamic properties as a function of orientation. Due to the melting and reheating of molten metal during fabrication, these materials tend to have internal porosity and slightly different microstructures along the weldments and normal to the weldments that may cause the materials to behave differently than their forged counterparts. The AM process builds up a part layer by layer, which provides opportunities to tailor geometry and optimize structural performance in addition to minimizing the amount of material waste for oddly shaped parts, thereby reducing cost. These advanced materials hold great promise for revolutionizing design, fabrication, and assembly of engineered components and could be used for many NNSA-specific applications including armoring complex elements of nuclear weapons, and customized diagnostic components in subcritical experiments. We have conducted materials studies in collaboration with the University of Nevada, Las Vegas (UNLV) as well as Los Alamos National Laboratory (LANL) under our Site-Directed Research and Development program and the Nevada Science Initiative. We are currently placing emphasis on quantifying how dynamic properties are affected by directionality and porosity of the material. A study of dynamic failure events in forged, layered, and additive manufactured (AM) titanium alloy subject to hypervelocity impact was conducted in collaboration with UNLV. Experiments were conducted using a two stage light-gas gun, 0.22-caliber Lexan projectiles, and different types of titanium target plates. A four-channel Photonic Doppler Velocimetry (PDV) system was used to study the free surface velocities to provide an understanding of the different failure mechanisms in these materials. The experimental measurements were used to validate computational simulations, which describe the behavior of these materials under shock. It was determined that AM, forged titanium, and multi-layered stacks produce similar velocity profiles during the early stage of impact, with the AM targets exhibiting spall at lower velocities and the multi-layered stacks exhibiting vibrations between plates. Simulations of solid and layered forged materials provide a good match to experimental data.

36 MATERIALS SCIENCE↗

Efficient and robust phase-split computations in the internal energy, volume, and moles ( UVN ) space

Phase-split computations in an isolated system, which in general may be defined as one where the total internal energy (U), volume (V), and the number of moles (N = N 1 , N 2 ,..., N n ) of the components are fixed at some specified set of values, involves the determination of the temperature (T), pressure (P), plus the amount and composition of the various phases that constitute the system. A simpler, but analogous problem is one where T, P, and N are specified instead. In TPN space, one may first perform a stability analysis to determine whether the system is stable, meaning whether at equilibrium it will split up into multiple phases or remain in single phase. If the single-phase state is unstable, the stability analysis reliably provides a good set of initial guesses in the subsequent phase-split computations. In UVN space, however, we demonstrate that the stability analysis (which is the main subject of our earlier study [1]) may not in general provide good enough initial guesses; we offer alternative strategies for setting up good initial guesses. Furthermore, we show that a combination of successive substitution iteration (SSI) and Newton's method---two iterative methods that are prevalent in the literature in TPN space---facilitates a robust and efficient algorithm for phase-split computations in isolated systems. Finally, this combination has so far not been applied in UVN space.

02 PETROLEUM↗

Carrier transport through the ultrathin silicon-oxide layer in tunnel oxide passivated contact (TOPCon) c-Si solar cells

The carrier transport through the silicon-oxide (SiO x ) layer in tunnel oxide passivated contact (TOPCon) c-Si solar cells has been studied experimentally and by simulation. The current intensity versus voltage (J-V) characteristics of GaIn/n-c-Si/SiO x /n + -poly-Si/Al structures shows a linear Ohmic characteristic, while a non-Ohmic behavior is observed in the samples without the n + -poly-Si contact layer. Conductive Atomic Force Microscopy (c-AFM) images reveal some current spikes on the surface of the samples, which could be related to the transport through pinholes. The simulation results show that 1) a rectification characteristic is obtained when only the tunneling mechanism is included, 2) both the reverse saturation current and the forward current increase when a small amount of transport through pinholes is introduced, and 3) finally a linear Ohmic behavior is observed when the pinhole transport component reaches a certain level. Furthermore, the simulation for whole TOPCon solar cells provides some useful results. For very thin SiO x (< 1.2 nm), the tunneling provides sufficient high tunneling probability and high efficiency TOPCon solar cells can be obtained without transport through pinholes if the passivation is ensured; while for a relatively thick SiO x (> 1.2 nm) without the transport through pinholes, the TOPCon solar cell shows a poor fill factor (FF) with a high series resistance (Rs) because the tunneling does not provide a sufficient high transport channel for carrier transport, and the introduction of a small number of transports through pinholes improves the FF and reduces the Rs, hence improves the PCE. However, a high possibility for carrier going through pinholes reduces all of the performance parameters and degrades PCE for all the cases simulated. Therefore, an optimized pinhole density and size distribution is critical engineering for solar cell performance optimization. However, the establishment of an optimized method to precisely control the pinhole formation and characterization is still on the way.

14 SOLAR ENERGY↗

Microplasma source for optogalvanic spectroscopy of nanogram samples

The demand for analysis of smaller samples in isotopic ratio measurements of rare isotopes is continuously rising with the development of new applications, particularly in biomedicine. Interesting in this aspect are methods based on optogalvanic spectroscopy, which have been reported to facilitate both {sup 13}C-to-{sup 12}C and {sup 14}C-to-{sup 12}C ratio measurements with high sensitivity. These methods also facilitate analysis of very small samples, down to the microgram range, which makes them very competitive to other technologies, e.g., accelerator mass spectroscopy. However, there exists a demand for moving beyond the microgram range, especially from regenerative medicine, where samples consist of, e.g., DNA, and, hence, the total sample amount is extremely small. Making optogalvanic spectroscopy of carbon isotopes applicable to such small samples, requires miniaturization of the key component of the system, namely the plasma source, in which the sample is ionized before analysis. In this paper, a novel design of such a microplasma source based on a stripline split-ring resonator is presented and evaluated in a basic optogalvanic spectrometer. The investigations focus on the capability of the plasma source to measure the optogalvanic signal in general, and the effect of different system and device specific parameters on the amplitude and stability of the optogalvanic signal in particular. Different sources of noise and instabilities are identified, and methods of mitigating these issues are discussed. Finally, the ability of the cell to handle analysis of samples down to the nanogram range is investigated, pinpointing the great prospects of stripline split-ring resonators in optogalvanic spectroscopy.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

COSMIC EVOLUTION OF SIZE AND VELOCITY DISPERSION FOR EARLY-TYPE GALAXIES

Massive (stellar mass M{sub *} {approx}> 3 x 10{sup 10} M{sub sun}), passively evolving galaxies at redshifts z {approx}> 1 exhibit on average physical sizes smaller, by factors {approx}3, than local early-type galaxies (ETGs) endowed with the same stellar mass. Small sizes are in fact expected on theoretical grounds, if dissipative collapse occurs. Recent results show that the size evolution at z {approx}< 1 is limited to less than 40%, while most of the evolution occurs at z {approx}> 1, where both compact and already extended galaxies are observed and the scatter in size is remarkably larger than it is locally. The presence at high redshift of a significant number of ETGs with the same size as their local counterparts, as well as ETGs with quite small size ({approx}<1/10 of the local one), points to a timescale for reaching the new, expanded equilibrium configuration of less than the Hubble time t{sub H} (z). We demonstrate that the projected mass of compact, high-redshift galaxies and that of local ETGs within the same physical radius, the nominal half-luminosity radius of high-redshift ETGs, differ substantially in that the high-redshift ETGs are on average significantly denser. This result suggests that the physical mechanism responsible for the size increase should also remove mass from central galaxy regions (r {approx}< 1 kpc). We propose that quasar activity, which peaks at redshift z {approx} 2, can remove large amounts of gas from central galaxy regions on a timescale shorter than the triggering a puffing up of the stellar component at constant stellar mass (or a timescale on the order of the dynamical one); in this case, the size increase goes together with a decrease in the central mass. The size evolution is expected to parallel that of the quasars and the inverse hierarchy, or downsizing, seen in the quasar evolution is mirrored in the size evolution. Exploiting the virial theorem, we derive the relation between the stellar velocity dispersion of ETGs and the characteristic velocity of their hosting halos at the time of formation and collapse. By combining this relation with the halo formation rate at z {approx}> 1, we predict the local velocity dispersion distribution function. On comparing it to the observed one, we show that velocity dispersion evolution of massive ETGs is fully compatible with the observed average evolution in size at constant stellar mass. Less massive ETGs (with stellar masses M{sub *} {approx}< 3 x 10{sup 10} M{sub sun}) are expected to evolve less both in size and in velocity dispersion, because their evolution is essentially determined by supernova feedback, which cannot yield winds as powerful as those triggered by quasars. The differential evolution is expected to leave imprints in the size versus luminosity/mass, velocity dispersion versus luminosity/mass, and central black hole mass versus velocity dispersion relationships, as observed in local ETGs.

79 ASTRONOMY AND ASTROPHYSICS↗

Thermal quench induced by a composite pellet-produced plasmoid

Injecting shattered pellets is the critical concept of the envisaged ITER disruption mitigation system (DMS). Rapid deposition of large amounts of material should presumably result in controlled cooling of the entire plasma. A considerable transfer of thermal energy from the electrons of the background plasma to the ions accompanies a localized material injection due to the ambipolar expansion along the magnetic field line of the cold and dense plasmoid produced by the ablated pellet. Radiation initially plays the dominant role in the energy balance of a composite plasmoid containing high-Z impurities. A competition between the ambipolar expansion and the radiative losses defines the Thermal Quench scenario, including the amount of pre-quench thermal energy radiated on a short collisional timescale—possibly detrimental for the plasma-facing components. The present work quantifies plasmoid energy balance for disruption mitigation parameters. For pure hydrogen injection, up to 90% of the pre-pellet electron thermal energy may go to the newly injected ions. We also demonstrate that a moderate high-Z impurity content within the plasmoid can reduce highly localized radiation at the beginning of the expansion. The thermal energy will then dissipate on the much longer ion collisional timescale, which would be attractive for ITER DMS.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Defensive Islanding to Enhance the Resilience of Distribution Systems Against Cyber-Induced Failures

The extensive integration of communication, computation, and control technologies into cyber-physical power systems (CPPSs) has increased the vulnerabilities of CPPSs to cyberattacks. This calls for developing solutions that assess and reduce the impacts of cyber-induced failures on CPPSs. This paper proposes a defensive islanding strategy to isolate impacted parts of the CPPS and form self-sufficient islanded grids with an objective of minimum load curtailment. The defensive islanding aims to split a power system into smaller grids to improve its resilience against a potential extreme event. A clustering approach that leverages the hierarchical spectral clustering method is utilized for the optimal defensive islanding. The proposed approach captures the fragility behavior and loading conditions of power system components due to cyber-induced failures. A graphical-based coupling framework is used to map the impacts of cyber failures into operation of power system components. The proposed method is demonstrated on a modified 33-node distribution feeder system integrated with distributed energy resources. The amount of load curtailment and radiality constraints have been used to evaluate the performance of the proposed clustering strategies. The results show the capability of the proposed algorithm to create islands considering the cyber-induced failures for enhanced resilience.

cyber-induced failures↗

Role of Vesicle-Inducing Protein in Plastids 1 in cpTat transport at the thylakoid

VIPP1 has been shown to be required for the proper formation of thylakoid membranes. However, studies on VIPP1 itself, as well as on PspA, its bacterial homolog, suggests that this protein may be involved in a number of additional functions, including protein translocation. The role of VIPP1 in protein translocation in the chloroplast has not been investigated. To this end, we conducted in vitro thylakoid protein transport assays to look at the effect of VIPP1 on the cpTat pathway, which is one of three translocation pathways found in both the chloroplast and its bacterial progenitor. We found that VIPP1 does indeed enhance protein transport through the cpTat pathway by up to 100%. The VIPP1 effect on cpTat activity occurs without interacting with the substrates or components of the translocon, and does not alter the energy potentials driving this translocation pathway. Instead, VIPP1 greatly enhances the amount of substrate bound productively to the thylakoids. Moreover, the presence of increasing VIPP1 concentrations in the reactions resulted in greater interactions between thylakoid membranes. Taken together, these results demonstrate a stimulatory role for VIPP1 in cpTat transport by enhancement of substrate binding, probably to the membrane lipid regions of the thylakoid. In conclusion, we propose a model in which VIPP1 facilitates reorganization of the thylakoid structure to increase substrate access to productive binding regions of the membrane as an early step in the cpTat pathway.

59 BASIC BIOLOGICAL SCIENCES↗

Lipid Droplets: Packing Hydrophobic Molecules Within the Aqueous Cytoplasm

Lipid droplets, also known as oil bodies or lipid bodies, are plant organelles that compartmentalize neutral lipids as a hydrophobic matrix covered by proteins embedded in a phospholipid monolayer. Some of these proteins have been known for decades, such as oleosins, caleosins, and steroleosins, whereas a host of others have been discovered more recently with various levels of abundance on lipid droplets, depending on the tissue and developmental stage. In addition to a growing inventory of lipid droplet proteins, the subcellular machinery that contributes to the biogenesis and degradation of lipid droplets is being identified and attention is turning to more mechanistic questions regarding lipid droplet dynamics. While lipid droplets are mostly regarded as storage deposits for carbon and energy in lipid-rich plant tissues such as seeds, these organelles are present in essentially all plant cells, where they display additional functions in signaling, membrane remodeling, and the compartmentalization of a variety of hydrophobic components. Remarkable metabolic engineering efforts have demonstrated the plasticity of vegetative tissues such as leaves to synthesize and package large amounts of storage lipids, which enable future applications in bioenergy and the engineering of high-value lipophilic compounds. Here, we review the growing body of knowledge about lipid droplets in plant cells, describe the evolutionary similarity and divergence in their associated subcellular machinery, and point to gaps that deserve future attention.

60 APPLIED LIFE SCIENCES↗