Search NASA⌕ Search

SEARCH · Search NASA

Results for “Enhanced Sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Surface Properties and RF Performance of Vapor Diffused Nb3Sn on NB After Sequential Anneals Below 1000°C

Nb3Sn is a next-generation superconducting material that can be used for future superconducting radiofrequency (SRF) accelerator cavities, promising better performance, cost reduction, and higher operating temperature than Nb. The Sn vapor diffusion method is currently the most preferred and successful technique to coat niobium cavi-ties with Nb3Sn. Among post-coating treatments to opti-mize the coating quality, higher temperature annealing without Sn is known to degrade Nb3Sn because of Sn loss. We have investigated Nb3Sn/Nb samples briefly annealed at 800-1000°C for 10 and 20 minutes to poten-tially improve the surface to enhance the performance of Nb3Sn-coated cavities. Following the sample studies, a coated single-cell cavity was sequentially annealed at 900°C and tested its performance each time, improving the cavity's quality factor relatively. This paper summarizes the sample studies and discusses the RF test results from sequentially annealed SRF Nb3Sn/Nb cavity.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Normalized Quantitative PCR Measurements as Predictors for Ethene Formation at Sites Impacted with Chlorinated Ethenes

Quantitative PCR (qPCR) targeting Dehalococcoides mccartyi (Dhc) biomarker genes supports effective management at sites impacted with chlorinated ethenes. To establish correlations between Dhc biomarker gene abundances and ethene formation (i.e., detoxification), 859 groundwater samples representing 62 sites undergoing monitored natural attenuation or enhanced remediation were analyzed. Dhc 16S rRNA genes and the vinyl chloride (VC) reductive dehalogenase genes bvcA and vcrA were detected in 88% and 61% of samples, respectively, from wells with ethene. Dhc 16S rRNA, bvcA , vcrA , and tceA (implicated in cometabolic reductive VC dechlorination) gene abundances all positively correlated with ethene formation. Significantly greater ethene concentrations were observed when Dhc 16S rRNA gene and VC RDase gene abundances exceeded 10 7 and 10 6 copies L –1 , respectively, and when Dhc 16S rRNA- and bvcA + vcrA -to-total bacterial 16S rRNA gene ratios exceeded 0.1%. Dhc 16S rRNA gene-to- vcrA/bvcA ratios near unity also indicated elevated ethene; yet, no increased ethene was observed in 19 wells where vcrA and/or bvcA gene copy numbers exceeded Dhc cell numbers 10- to 10 000-fold. Approximately one-third of samples with detectable ethene lacked bvcA , vcrA , and tceA , implying that comprehensive understanding of VC detoxification biomarkers has not been achieved. Although the current biomarker suite is incomplete, the data analysis corroborates the value of the available Dhc DNA biomarkers for prognostic and diagnostic groundwater monitoring at sites impacted with chlorinated ethenes.

59 BASIC BIOLOGICAL SCIENCES↗

Hydrogen effect on the morphology and structure of 3D porous titanium in the HFCVD-diamond growth environment

Titanium hydride was obtained from hydrogenation process on pure titanium (Ti) using a hot filament chemical vapor deposition reactor. The Ti samples were produced from powder metallurgy technique and present three-dimensional porosity. The experimental parameters of the hydrogenation process were controlled in a similar way as those for diamond growth. The pressure inside the reactor was kept at 6.6 kPa for a H{sub 2} flow rate of 100 sccm and hydrogenation time of 1 hour. The distance from the filaments to the Ti surface was kept at 5 mm. Hydrogenation processes were carried out at different temperatures of 773, 873, 973 and 1073 K. The morphology of the titanium hydrides was studied by scanning electron microscopy. The images showed an increase in the roughness titanium surface as well as the formation of cracks due to the hydride titanium precipitation. The structure of these titanium hydrides was analyzed by X-ray diffraction, performed through {theta}-2{theta} scans from 1 to 15{sup o} grazing incident angle. The results revealed that the temperature enhanced the titanium hydride concentration in the samples with a predominant precipitation of TiH phase for the four temperatures studied. - Highlights: {yields} Hydrogen quickly spread out in the Ti matrix reacting and generating TiH phases. {yields} The higher the hydrogenation temperature the higher the amount of TiH formation. {yields} The volume increasing associated with the TiH formation caused tensions in the Ti metallic matrix. {yields} The TiH increases the Ti surface roughness influencing the grain size reduction.

36 MATERIALS SCIENCE↗

Inferring the Redshift of More than 150 GRBs with a Machine-learning Ensemble Model

Gamma-ray bursts (GRBs), due to their high luminosities, are detected up to a redshift of 10, and thus have the potential to be vital cosmological probes of early processes in the Universe. Fulfilling this potential requires a large sample of GRBs with known redshifts, but due to observational limitations, only 11% have known redshifts (z). There have been numerous attempts to estimate redshifts via correlation studies, most of which have led to inaccurate predictions. To overcome this, we estimated GRB redshift via an ensemble-supervised machine-learning (ML) model that uses X-ray afterglows of long-duration GRBs observed by the Neil Gehrels Swift Observatory. The estimated redshifts are strongly correlated (a Pearson coefficient of 0.93) and have an rms error, namely, the square root of the average squared error $\langle$Δz 2 $\rangle$, of 0.46 with the observed redshifts showing the reliability of this method. The addition of GRB afterglow parameters improves the predictions considerably by 63% compared to previous results in peer-reviewed literature. Finally, we use our ML model to infer the redshifts of 154 GRBs, which increase the known redshifts of long GRBs with plateaus by 94%, a significant milestone for enhancing GRB population studies that require large samples with redshift.

79 ASTRONOMY AND ASTROPHYSICS↗

RUBIDIUM IN THE INTERSTELLAR MEDIUM

We present observations of interstellar rubidium toward o Per, zeta Per, AE Aur, HD 147889, chi Oph, zeta Oph, and 20 Aql. Theory suggests that stable {sup 85}Rb and long-lived {sup 87}Rb are produced predominantly by high-mass stars, through a combination of the weak s- and r-processes. The {sup 85}Rb/{sup 87}Rb ratio was determined from measurements of the Rb I line at 7800 A and was compared to the solar system meteoritic ratio of 2.59. Within 1sigma uncertainties, all directions except HD 147889 have Rb isotope ratios consistent with the solar system value. The ratio toward HD 147889 is much lower than the meteoritic value and similar to that toward rho Oph A; both lines of sight probe the Rho Ophiuchus Molecular Cloud. The earlier result was attributed to a deficit of r-processed {sup 85}Rb. Our larger sample suggests instead that {sup 87}Rb is enhanced in these two lines of sight. When the total elemental abundance of Rb is compared to the K elemental abundance, the interstellar Rb/K ratio is significantly lower than the meteoritic ratio for all the sight lines in this study. Available interstellar samples for other s- and r- process elements are used to help interpret these results.

79 ASTRONOMY AND ASTROPHYSICS↗

High-Resolution Computed Tomography Dataset of Mount Simon Sandstone

The Illinois Basin is a critical structure for subsurface energy related activities and their implementation in the United States. The Mount Simon Sandstone has been identified as a storage target for permanent and transient storage of fluids in the basin. Known for its exceptional thickness, depth, porosity, and sealing properties of overlying formations, this saline reservoir is crucial for long-term subsurface energy efforts. We present an extensive Computed Tomography (CT) dataset on a high porosity and permeability zone in the lower Mount Simon Sandstone available on the Energy Data eXchange® (EDX). This publicly accessible database comprises over 500 GB of high-resolution CT scans of six core samples, with resolutions ranging from 14.8 µm to 0.7 µm per pixel. The scans include both dry sandstone samples and those saturated with multiple fluids, allowing for comparative analyses across different conditions and resolutions. Coarser scans capture the bedding structure of the sandstone, while finer resolutions reveal detailed pore infill and throat characteristics. Metadata on location, depth, and saturation state enhance usability, enabling quick identification and cross-sample comparisons. By providing a robust resource for research and collaboration, the database contributes to domestic energy advancement by supporting continued progress in the use of the subsurface for energy solutions.

characterization↗

The Office of Groundwater & Soil Remediation Fiscal Year 2011 Research & Development Program

The U.S. Department of Energy's (DOE) Office of Groundwater and Soil Remediation supports technology development and technical assistance for the remediation of environments contaminated by legacy nuclear waste. The core of the program is centered on delivering proactive, responsive expertise and technologies with highly-leveraged, carefully selected investments that maximum impact on life-cycle cleanup costs and risks across the DOE complex. The program currently focuses on four main priorities: improved sampling and characterization strategies, advanced predictive capabilities, enhanced remediation methods, and improved long-term performance evaluation and monitoring. In FY 2010, the program developed a detailed research and development (R and D) plan in support of a larger initiative to integrate R and D efforts across EM. This paper provides an overview of the priority action areas and the program's near-term technical direction.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Reduction Enhancement Mechanisms of a Low-Grade Iron Ore–Coal Composite by NaCl

The reduction behavior of a low iron grade with high SiO{sub 2} content ore–coal composite was investigated in the temperature range of 1143 K to 1263 K (870 °C to 990 °C). Sodium chloride was chosen as an additive to promote this reduction process. The effect of the sodium chloride addition and its mechanism was also investigated. Results showed that the added sodium chloride could enhance the reduction of wustite to iron due to the decrease of fayalite, and a higher metallization ratio of reduced sample was obtained. Thermogravimetric–differential scanning calorimeter analysis showed that sodium chloride could greatly facilitate the gasification process of coal and, thus, provide sufficient carbon monoxide to the reduction process of iron oxides. Meanwhile, sodium chloride promoted the reduction process of iron ore pellets directly as the coal gasification effect was excluded. Microstructures of reduced sample revealed that sodium chloride broke the structure of ore and enhanced the growth of newly formed iron particles. As the ore–coal composite with mol (C/Fe = 1.4) and 3 mass pct sodium chloride addition was roasted at 1233 K (960 °C) for 55 minutes, a reduced sample with metallization ration of 74.45 pct could be obtained.

36 MATERIALS SCIENCE↗

The frequency of enhanced star formation in interacting and isolated galaxies

To probe the sensitivity of the star formation rate and extent in galaxies to gravitational encounters, ground based near and mid-infrared and IRAS far-infrared measurements of complete samples of isolated and interacting pairs of galaxies were obtained. The observed infrared properties of the isolated galaxies are used to gauge the magnitude of star formation in galaxies free from external influences, and to define the relationships between morphological type and infrared luminosity. These properties were contrasted with those of the interacting sample to examine the extent to which interactions can enhance or alter the nature of star formation. The mechanisms by which interactions influence activity such as star formation are investigated through correlations of the infrared characteristics with radio and optical measurements, and with morphological and physical parameters such as galaxy types, separations, encounter velocities and interaction types. Limits to the physical extent of the star formation are obtained by comparing the large aperture measurements of IRAS with the small aperture ground based photometry.

Cutri, Roc M.↗

Defect mediated reversible ferromagnetism in Co and Mn doped zinc oxide epitaxial films

We have introduced defects in ZnO (undoped and doped with Co and Mn) epitaxial thin films using laser irradiation from nanosecond laser pulses and thermal annealing in oxygen ambient. In contrast to the as grown samples, the laser irradiated films show a significant increase in conductivity, enhancement in UV emission, while maintaining the same wurtzite crystal structure. Room-temperature ferromagnetism (RTFM) is observed in laser-irradiated samples, which increased with the number of laser pulses up to a certain value where magnetic moment saturates. The induced ferromagnetism as well as the enhanced electrical conductivity can be reversed with thermal annealing in oxygen ambient. The magnetization in Co and Mn doped films was found to be strong function of growth conditions and defect concentration. X-ray diffraction and optical absorption experiments suggested a 2+ valance state and tetrahedral coordination for both Co and Mn ions. There is a simultaneous increase in n-type electrical conductivity with the number of laser pulses and continue to exhibit semiconducting behavior in both undoped and doped films. The saturation magnetization was found to be 0.08 {mu}{sub B}/Co and 0.05 {mu}{sub B}/Mn, much lower than 3.0 {mu}{sub B}/Co and 5.0 {mu}{sub B}/Mn, indicating the prominent role of intrinsic defects in RTFM with some contribution from Co{sup 2+}-oxygen vacancy complexes. We propose a unified mechanism based upon introduction of intrinsic defects to explain RTFM and n-type conductivity enhancements during pulsed laser and thermal annealing.

36 MATERIALS SCIENCE↗

OBSERVATIONAL PROPERTIES OF THE METAL-POOR THICK DISK OF THE MILKY WAY AND INSIGHTS INTO ITS ORIGINS

We have undertaken the study of the elemental abundances and kinematic properties of a metal-poor sample of candidate thick-disk stars selected from the Radial Velocity Experiment spectroscopic survey of bright stars to differentiate among the present scenarios of the formation of the thick disk. In this paper, we report on a sample of 214 red giant branch, 31 red clump/horizontal branch, and 74 main-sequence/sub-giant branch metal-poor stars, which serves to augment our previous sample of only giant stars. We find that the thick disk [{alpha}/Fe] ratios are enhanced and have little variation (<0.1 dex), in agreement with our previous study. The augmented sample further allows, for the first time, investigation of the gradients in the metal-poor thick disk. For stars with [Fe/H] < -1.2, the thick disk shows very small gradients, <0.03 {+-} 0.02 dex kpc{sup -1}, in {alpha}-enhancement, while we find a +0.01 {+-} 0.04 dex kpc{sup -1} radial gradient and a -0.09 {+-} 0.05 dex kpc{sup -1} vertical gradient in iron abundance. In addition, we show that the peak of the distribution of orbital eccentricities for our sample agrees better with models in which the stars that comprise the thick disk were formed primarily in the Galaxy, with direct accretion of stars contributing little. Our results thus disfavor direct accretion of stars from dwarf galaxies into the thick disk as a major contributor to the thick-disk population, but cannot discriminate between alternative models for the thick disk, such as those that invoke high-redshift (gas-rich) mergers, heating of a pre-existing thin stellar disk by a minor merger, or efficient radial migration of stars.

79 ASTRONOMY AND ASTROPHYSICS↗

Lunar Surface Mixed Reality and ARGOS Trainer

This Artemis focused Mixed Reality (MR) and ARGOS project extends the current VR/ARGOS CIF project to enhance and add VR/MR capabilities to support analysis, training and risk reduction for lunar surface EVA operations in the extreme South Pole lunar environment. This third year focused on establishing a functional trainer for crew that supports the ingress/egress of a lander as well as surface tasks such as sample collection and tool deployment and operation. Completed enhancements include improving hand tracking, the addition of supporting mixed reality surface operations, and the implementation of a higher fidelity body tracking capability through a motion capture system.

Lunar↗

Nanosegregated surfaces as catalysts for fuel cells

A method of preparing a nanosegregated Pt alloy having enhanced catalytic properties. The method includes providing a sample of Pt and one or more of a transition metal in a substantially inert environment, and annealing the sample in such an environment for a period of time and at a temperature profile to form a nanosegregated Pt alloy having a Pt-skin on a surface. The resulting alloy is characterized by a plurality of compositionally oscillatory atomic layers resulting in an advantageous electronic structure with enhanced catalytic properties.

Stamenkovic, Vojislav↗

GeoLab: A Geological Workstation for Future Missions

The GeoLab glovebox was, until November 2012, fully integrated into NASA's Deep Space Habitat (DSH) Analog Testbed. The conceptual design for GeoLab came from several sources, including current research instruments (Microgravity Science Glovebox) used on the International Space Station, existing Astromaterials Curation Laboratory hardware and clean room procedures, and mission scenarios developed for earlier programs. GeoLab allowed NASA scientists to test science operations related to contained sample examination during simulated exploration missions. The team demonstrated science operations that enhance theThe GeoLab glovebox was, until November 2012, fully integrated into NASA's Deep Space Habitat (DSH) Analog Testbed. The conceptual design for GeoLab came from several sources, including current research instruments (Microgravity Science Glovebox) used on the International Space Station, existing Astromaterials Curation Laboratory hardware and clean room procedures, and mission scenarios developed for earlier programs. GeoLab allowed NASA scientists to test science operations related to contained sample examination during simulated exploration missions. The team demonstrated science operations that enhance the early scientific returns from future missions and ensure that the best samples are selected for Earth return. The facility was also designed to foster the development of instrument technology. Since 2009, when GeoLab design and construction began, the GeoLab team [a group of scientists from the Astromaterials Acquisition and Curation Office within the Astromaterials Research and Exploration Science (ARES) Directorate at JSC] has progressively developed and reconfigured the GeoLab hardware and software interfaces and developed test objectives, which were to 1) determine requirements and strategies for sample handling and prioritization for geological operations on other planetary surfaces, 2) assess the scientific contribution of selective in-situ sample characterization for mission planning, operations, and sample prioritization, 3) evaluate analytical instruments and tools for providing efficient and meaningful data in advance of sample return and 4) identify science operations that leverage human presence with robotic tools. In the first year of tests (2010), GeoLab examined basic glovebox operations performed by one and two crewmembers and science operations performed by a remote science team. The 2010 tests also examined the efficacy of basic sample characterization [descriptions, microscopic imagery, X-ray fluorescence (XRF) analyses] and feedback to the science team. In year 2 (2011), the GeoLab team tested enhanced software and interfaces for the crew and science team (including Web-based and mobile device displays) and demonstrated laboratory configurability with a new diagnostic instrument (the Multispectral Microscopic Imager from the JPL and Arizona State University). In year 3 (2012), the GeoLab team installed and tested a robotic sample manipulator and evaluated robotic-human interfaces for science operations.

Evans, Cynthia↗

A scanning quantum cryogenic atom microscope at 6 K

The Scanning Quantum Cryogenic Atom Microscope (SQCRAMscope) is a quantum sensor in which a quasi-1D quantum gas images electromagnetic fields emitted from a nearby sample. We report improvements to the microscope. Cryogen usage is reduced by replacing the liquid cryostat with a closed-cycle system and modified cold finger, and cryogenic cooling is enhanced by adding a radiation shield. The minimum accessible sample temperature is reduced from 35~K to 5.7~K while maintaining low sample vibrations. A new sample mount is easier to exchange, and quantum gas preparation is streamlined.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Absorber Clamp for Microcalorimeter Decay Energy Spectrometry

Microcalorimeter Decay Energy Spectrometry (DES) is of interest to nuclear safeguards due to its ability to provide high precision isotopic compositions of nanogram-to microgram-scale samples of Pu and U and related daughter products. The DES method is able to record decay energy of each alpha-decay event in a sample that is embedded in a metal matrix (absorber) and thermally linked to a microcalorimeter detector. This work optimizes the DES technique used to thermally link the absorber and microcalorimeter detector element to allow for more rapid assembly and to increase detector performance and operating life. Optimized attachment methods are crucial for enhancing the viability of DES in high-sample-throughput facilities, such as those that support international nuclear safeguards measurements. Here, in this study, we designed and implemented a pressure-based absorber clamp and evaluated the performance of this new attachment method relative to pressed indium bond attachment. Results using the absorber clamp demonstrate a streamlined detector assembly procedure that minimizes accidental damage to detectors, as well as increasing detector pulse speeds by 57%. Spectral comparison shows the clamp preserves detector performance relative to indium attachment.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Enhancement in dielectric behavior of (Ni, Zn)Fe{sub 2}O{sub 4} ferrite

In present work, NiFe{sub 2}O{sub 4}(NFO), ZnFe{sub 2}O{sub 4} (ZFO) and Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} (NZFO) are synthesized by microwave assisted co-precipitation route. Their structural properties are confirmed by X-ray diffraction and data is fitted through Reitveld refinement using Full-Prof software suite. After refinement, the systematic crystal structures of NFO, ZFO and NZFO compounds are generated using output .cif file by VESTA (Visualization for Electronic and Structural Analysis) program. Structural parameters obtained after refinement and unit cell construction, are systematically tabulated. Room temperature frequency dependence dielectric properties are studied. We found enhanced values of dielectric constant for NZFO than individual NFO and ZFO phases. For NZFO sample, greater electron exchange between Fe{sup 2+} and Fe{sup 3+} which enhances polarization and dielectric constant.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of plasticizers on thermal and mechanical properties of biocomposite filaments made from lignin and polylactic acid for 3D printing

Polylactic acid (PLA) and organosolv lignin were mixed at different ratios and extruded to obtain PLA-lignin composite filaments. PLA was replaced with lignin up to 20 wt%. Two plasticizers (polyethylene glycol (PEG) 2000 and struktol TR451) were added in varying concentrations to enhance the properties of PLA_L20 (20% lignin in PLA) composite filaments. Furthermore, the effect of lignin in PLA, and PEG, and struktol in PLA_L20 composites was investigated via tensile test, differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy, Fourier transform infrared spectroscopy of the filaments, and dynamic mechanical analysis of 3D printed samples. A 2 wt% PEG was able to enhance both tensile stress and elongation at maximum load of PLA_L20 composite by 19% and 35%, respectively, whereas struktol TR451 was able to improve elongation at maximum load by 24%.

3D printing↗