Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fast Fourier Transform”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Fourier analysis by spectral transformation (Fast) Photonic Doppler Velocimetry (PDV) with signal fade mitigation

A state-of-the-art class of photonic Doppler velocimetry (PDV) diagnostic and novel methods to stabilize any class of PDV signal has been developed. The former brings velocimetry to new extremes in maximum velocity and fast time resolution, while maintaining precision velocity resolution, long record length capability, and the ability to record multiple velocities simultaneously. The latter compensates for large changes in signal intensity common in many experiments.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Operando Measurements of Electrolyte Li-ion Concentration during fast charging with FTIR/ATR

The ability to charge a Li-ion battery at high charging rates is critical for electric vehicle adoption; however, further study of ion transport is required to develop electrolytes suitable for fast charge. Fourier transform infrared spectroscopy (FTIR) used with attenuated total reflection (ATR) enables operando measurements of liquid electrolytes. This research focused on solvation shifting of solvent infrared absorption bands in the presence of lithium ions. Lithium-shifted infrared absorption bands and non-shifted bands of ethyl methyl carbonate (EMC) and ethylene carbonate (EC) were compared to infer ion concentration changes during cycling. Lithium concentrations were calibrated using EC/EMC/LiPF 6 electrolytes with known lithium concentrations. A Li-ion half-cell with a graphite anode and EC/EMC/LiPF 6 electrolyte was observed with FTIR/ATR. The results showed that the magnitude of lithium concentration changes increased with increasing C-rate. During a galvanostatic intermittent titration technique (GITT) test, changes in lithium concentration could be observed. During intercalation, a lithium depletion occurred when a negative current was applied, and a lithium surplus occurred during deintercalation when a positive current was applied. The capability of observing lithium concentration has significant implications for the utility of operando studies and the potential to link lithium movement to battery performance.

25 ENERGY STORAGE↗

Highly-efficient quantum Fourier transformations for certain non-Abelian groups

Quantum Fourier transformations are an essential component of many quantum algorithms, from prime factoring to quantum simulation. While the standard Abelian QFrT is well studied, important variants corresponding to non-Abelian groups of interest have seen less development. In particular, fast non-Abelian Fourier transformations are important components for both quantum simulations of field theories as well as approaches to the non-Abelian hidden subgroup problem. In this work, we present fast quantum Fourier transformations for a number of non-Abelian groups of interest for high energy physics, B T , B O , 6 Δ ( 27 ) , Δ ( 54 ) , and Σ ( 36 × 3 ) . For each group, we derive explicit quantum circuits and estimate resource scaling for fault-tolerant implementations. Our work shows that the development of a fast Fourier transformation can substantively reduce simulation costs by an up to three orders of magnitude for the finite groups that we have investigated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Pre-Hardware Optimization and Implementation Of Fast Optics Closed Control Loop Algorithms

One of the main heritage tools used in scientific and engineering data spectrum analysis is the Fourier Integral Transform and its high performance digital equivalent - the Fast Fourier Transform (FFT). The FFT is particularly useful in two-dimensional (2-D) image processing (FFT2) within optical systems control. However, timing constraints of a fast optics closed control loop would require a supercomputer to run the software implementation of the FFT2 and its inverse, as well as other image processing representative algorithm, such as numerical image folding and fringe feature extraction. A laboratory supercomputer is not always available even for ground operations and is not feasible for a night project. However, the computationally intensive algorithms still warrant alternative implementation using reconfigurable computing technologies (RC) such as Digital Signal Processors (DSP) and Field Programmable Gate Arrays (FPGA), which provide low cost compact super-computing capabilities. We present a new RC hardware implementation and utilization architecture that significantly reduces the computational complexity of a few basic image-processing algorithm, such as FFT2, image folding and phase diversity for the NASA Solar Viewing Interferometer Prototype (SVIP) using a cluster of DSPs and FPGAs. The DSP cluster utilization architecture also assures avoidance of a single point of failure, while using commercially available hardware. This, combined with the control algorithms pre-hardware optimization, or the first time allows construction of image-based 800 Hertz (Hz) optics closed control loops on-board a spacecraft, based on the SVIP ground instrument. That spacecraft is the proposed Earth Atmosphere Solar Occultation Imager (EASI) to study greenhouse gases CO2, C2H, H2O, O3, O2, N2O from Lagrange-2 point in space. This paper provides an advanced insight into a new type of science capabilities for future space exploration missions based on on-board image processing for control and for robotics missions using vision sensors. It presents a top-level description of technologies required for the design and construction of SVIP and EASI and to advance the spatial-spectral imaging and large-scale space interferometry science and engineering.

Kizhner, Semion↗

Stratospheric Horizontal Wavenumber Spectra of Winds, Potential Temperature, and Atmospheric Tracers Observed by High-Altitude Aircraft

Horizontal wavenumber power spectra of vertical and horizontal wind velocities, potential temperatures, and ozone and N(2)O mixing ratios, as measured in the mid-stratosphere during 73 ER-2 flights (altitude approx. 20km) are presented. The velocity and potential temperature spectra in the 100 to 1-km wavelength range deviate significantly from the uniform -5/3 power law expected for the inverse energy-cascade regime of two-dimensional turbulence and also for inertial-range, three-dimensional turbulence. Instead, steeper spectra approximately consistent with a -3 power law are observed at horizontal scales smaller than 3 km for all velocity components as well as potential temperature. Shallower spectra are observed at scales longer than 6 km. For horizontal velocity and potential temperature the spectral indices at longer scales are between -1.5 and -2.0. For vertical velocity the spectrum at longer scales become flat. It is argued that the observed velocity and potential temperature spectra are consistent with gravity waves. At smaller scales, the shapes are also superficially consistent with a Lumley-Shur-Weinstock buoyant subrange of turbulence and/or nonlinear gravity waves. Contemporaneous spectra of ozone and N(sub 2)O mixing ratio in the 100 to 1-km wavelength range do conform to an approximately uniform -5/3 power law. It is argued that this may reflect interactions between gravity wave air-parcel displacements and laminar or filamentary structures in the trace gas mixing ratio field produced by enstropy-cascading two-dimensional turbulence.

TRACE GAS MIXING RATIO FIELDS↗

Preprocessing for Unintended Conducted Emissions Classification with ResNet

Characterization of Unintended Conducted Emissions (UCE) from electronic devices is important when diagnosing electromagnetic interference, performing nonintrusive load monitoring (NILM) of power systems, and monitoring electronic device health, among other applications. Prior work has demonstrated that UCE analysis can serve as a diagnostic tool for energy efficiency investigations and detailed load analysis. While explaining the feature selection of deep networks with certainty is often not fully comprehensive, or in other applications, quite lacking, additional tools/methods for further corroboration and confirmation can help further the understanding of the researcher. This is true especially in the subject application of the study in this paper. Often the focus of such efforts is the selected features themselves, and there is not as much understanding gained about the noise in the collected data. If selected feature and noise characteristics are known, it can be used to further shape the design of the deep network or associated preprocessing. This is additionally difficult when the available data are limited, as in the case which the authors investigated in this study. Here, the authors present a novel work (which is a proposed complementary portion of the overall solution to the deep network classification explainability problem for this application) by applying a systematic progression of preprocessing and a deep neural network (ResNet architecture) to classify UCE data obtained via current transformers. By using a methodical application of preprocessing techniques prior to a deep classifier, hypotheses can be produced concerning what features the deep network deems important relative to what it perceives as noise. For instance, it is hypothesized in this particular study as a result of execution of the proposed method and periodic inspection of the classifier output that the UCE spectral features are relatively close to each other or to the interferers, as systematically reducing the beta parameter of the Kaiser window produced progressively better classification performance, but only to a point, as going below the Beta of eight produced decreased classifier performance, as well as the hypothesis that further spectral feature resolution was not as important to the classifier as rejection of the leakage from a spectrally distant interference. This can be very important in unpredictable low-FNR applications, where knowing the difference between features and noise is difficult. As a side-benefit, much was learned regarding the best preprocessing to use with the selected deep network for the UCE collected from these low power consumer devices obtained via current transformers. Baseline rectangular windowed FFT preprocessing provided a 62% classification increase versus using raw samples. After performing a more optimal preprocessing, more than 90% classification accuracy was achieved across 18 low-power consumer devices for scenarios in which the in-band features-to-noise ratio (FNR) was very poor.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

The occurrence and wave properties of H⁺-, He⁺-, and O⁺-band EMIC waves observed by the Van Allen Probes

We perform a statistical study of electromagnetic ion cyclotron (EMIC) waves detected by the Van Allen Probes mission to investigate the spatial distribution of their occurrence, wave power, ellipticity, and normal angle. The Van Allen Probes have been used which allow us to explore the inner magnetosphere (1.1 to 5.8 RE). Magnetic field measurements from the Electric and Magnetic Field Instrument Suite and Integrated Science on board the Van Allen Probes are used to identify EMIC wave events for the first 22 months of the mission operation (8 September 2012 to 30 June 2014). EMIC waves are examined in H⁺-, He⁺-, and O⁺-bands. Over 700 EMIC wave events have been identified over the three different wave bands (265 H⁺-band events, 438 He⁺-band events, and 68 O⁺-band events). EMIC wave events are observed between L = 2 – 8, with over 140 EMIC wave events observed below L = 4. The results show that H⁺-band EMIC waves have two peak magnetic local time (MLT) occurrence regions: pre-noon (09:00 < MLT ≤ 12:00) and afternoon (15:00 < MLT ≤ 17:00) sectors. He⁺-band EMIC waves feature an overall stronger dayside occurrence. O⁺-band EMIC waves have one peak region located in the morning sector at lower L shells (L < 4). He⁺-band EMIC waves average the highest wave power overall (>0.1 nT²/Hz), especially in the afternoon sector. Ellipticity observations reveal that linearly polarized EMIC waves dominate in lower L shells.

58 GEOSCIENCES↗

Computational Homogenization of Polycrystals

This paper reviews the current state of the art in the simulation of the mechanical behavior of polycrystalline materials by means of computational homogenization. The key ingredients of this modeling strategy are presented in detail starting with the parameters needed to describe polycrystalline microstructures and the digital representation of such microstructures in a suitable format to perform computational homogenization. The different crystal plasticity frameworks that can describe the physical mechanisms of deformation in single crystals (dislocation slip and twinning) at the microscopic level are presented next. This is followed by the description of computational homogenization methods based on mean-field approximations by means of the viscoplastic self-consistent approach, or on the full-field simulation of the mechanical response of a representative polycrystalline volume element by means of the finite element method or the fast Fourier transform-based method. Multiscale frameworks based on the combination of mean-field homogenization and the finite element method are presented next to model the plastic deformation of polycrystalline specimens of arbitrary geometry under complex mechanical loading. Examples of application to predict the strength, fatigue life, damage, and texture evolution under different conditions are presented to illustrate the capabilities of the different models. Lastly, current challenges and future research directions in this field are summarized.

36 MATERIALS SCIENCE↗

Evaluating the grain-scale deformation behavior of a single-phase FCC high entropy alloy using synchrotron high energy diffraction microscopy

We report although the deformation behavior of high-entropy alloys (HEAs) has been extensively studied at the macroscale, many important properties have yet to be explored for these alloys at the microscale, thus hampering accurate prediction of damage and failure processes. Synchrotron high-energy diffraction microscopy (HEDM) and fast-Fourier transform-based crystal plasticity modeling was conducted to investigate the three-dimensional (3D) grain-resolved micromechanical response for approximately 1,900 constituent grains within a single-phase FCC HEA up to 1% applied strain. The evolution of grain-resolved elastic strains, lattice reorientations, and maximum resolved shear stresses (mRSS) were evaluated to quantify elastic, yield, and fully plastic behavior. Overall, the initial critical resolved shear stress (CRSS), determined via in situ HEDM and companion modeling, was found to be > 20% higher than estimated using the classical polycrystalline Taylor factor (M = 3.06). However, a descriptive parameter based on the average grain-resolved Taylor factor ($\overline{M}$) was found to show excellent agreement with plastic yielding behavior observed within HEDM datasets. Noticeable deviations in HEDM lattice reorientations compared to both EVP-FFT simulations and classical predictions for FCC polycrystals were discovered, highlighting the complexity in correlating local lattice reorientations, Taylor, and Schmid factors with plastic response for this material at the grain-scale. Therefore, it is anticipated that the overall trends and parameter identification of 3D grain-resolved properties in this study can serve as an important foundation for continued mesoscale investigation on both well-established and newly developed Cantor-like HEAs.

36 MATERIALS SCIENCE↗

Phase-field modeling of thermally-grown oxide and damage evolution in environmental barrier coatings

Silicon carbide-based ceramic matrix composites protected by environmental barrier coatings (EBCs) present a promising materials solution for next-generation gas turbines. Developing more robust and efficient EBCs is therefore of significant technological importance. During the service in high-temperature oxidative environments, there is a thermally grown oxide (TGO) layer, spontaneously formed in the EBC system. TGO is recognized as a critical factor for the degradation and failure of EBCs, yet the detailed mechanisms of TGO growth and its effect on EBC failure remain unclear. In this study we develop a comprehensive chemo-mechano-phase-field model to simulate growth of the TGO in EBCs, factoring in creep and deformation, and especially the cracking behaviors. The volume expansion due to TGO growth and the resulting large inelastic deformation are addressed by using our recently developed, so-called incremental realization of inelastic deformation (IRID) algorithm, in combination with an adapted Hu-Chen spectral solver for elasticity. Simulations of TGO growth are performed considering different growth modes of TGOs determined mainly by the ratio of oxidant permeability in the topcoat to that in the TGO itself. Large-scale three-dimensional (3D) simulations are performed to model the formation of interconnecting vertical/channel cracks (often called ‘mud cracks’). The simulated crack morphology are in excellent agreement with the experimental observations from the literature. The simulations also provide insights into the cracking of EBCs and its dependence on the structure and constituent properties of the coating system. Furthermore, these results demonstrate the developed damage model can be a useful tool for design of more durable EBCs.

Cracking↗

Neural operators for stochastic modeling of nonlinear structural system response to natural hazards

Traditionally, neural networks have been employed to learn the mapping between finite-dimensional Euclidean spaces. However, recent research has opened up new horizons, focusing on the utilization of deep neural networks to learn operators capable of mapping infinite-dimensional function spaces. Here, in this work, we employ two state-of-the-art neural operators, the deep operator network (DeepONet) and the Fourier neural operator (FNO) for the prediction of the nonlinear time history response of structural systems exposed to natural hazards, such as earthquakes and windstorms. Specifically, we propose two architectures, a self-adaptive FNO and a fast Fourier transform-based DeepONet (DeepFNOnet), where we employ a FNO beyond the DeepONet to learn the discrepancy between the ground truth and the solution predicted by the DeepONet. To demonstrate the efficiency and applicability of the architectures, two problems are considered. In the first, we use the proposed model to predict the seismic nonlinear dynamic response of a six-story shear building subject to stochastic ground motions. In the second problem, we employ the operators to predict the wind-induced nonlinear dynamic response of a high-rise building while explicitly accounting for the stochastic nature of the wind excitation. In both cases, the trained metamodels achieve high accuracy while being orders of magnitude faster than their corresponding high-fidelity models.

DeepONet↗

A new micromechanics based full field numerical framework to simulate the effects of dynamic recrystallization on the formability of HCP metals

This work presents a new full-field, efficient and mesh-free numerical framework to model microstructure evolution, dynamic recrystallization (DRX) and formability in hexagonal closed-packed (HCP) metals such as magnesium alloys at warm temperatures. A rate tangent-fast Fourier transform-based elasto-viscoplastic crystal plasticity constitutive model for HCP metals (RTCP-FFT-HCP) is coupled with a probabilistic cellular automata (CA) approach to model DRX (CA-DRX). Furthermore, this new model is coupled with the Marciniak-Kuczynski (M-K) approach to model formability of magnesium alloys at elevated temperatures. The RTCP-FFT-HCP model computes macro stress-strain, twinning volume fraction, micromechanical fields, texture evolution and local dislocation density. Nucleation of new grains and their subsequent growth is modeled using the cellular automata approach with probabilistic state switching rule. First, the proposed RTCP-FFT-HCP model is validated by comparing the predicted stress-strain responses and texture evolution under uniaxial tension and compression with experimental measurements for AZ31 sheet alloy at room temperature. The coupled CA-RTCPFFT-HCP model is further validated by comparing the predicted stress-strain responses and texture evolution in uniaxial compression with experimental measurements at 100 °C, 200 °C and 300 °C for the AZ31 sheet alloy. Next, the forming limit diagrams (FLDs) with and without including the effects of DRX are simulated at 100 °C, 200 °C and 300 °C for AZ31 sheet alloy. The predicted FLDs with DRX show very good agreement with the experimental measurements and clearly demonstrate the need for an accurate DRX model. The study reveals that the DRX strongly affects the deformed grain structure, grain size and texture evolution and also highlights the importance accounting for DRX during FLD simulations at high temperatures.

36 MATERIALS SCIENCE↗

Time for anisotropy: The significance of mechanical anisotropy for the development of deformation structures

The forty-year history of the Journal of Structural Geology has recorded an enormous increase in the description, interpretation and modelling of deformation structures. Amongst factors that control deformation and the resulting structures, mechanical anisotropy has proven difficult to tackle. Using a Fast Fourier Transform-based numerical solver for viscoplastic deformation of crystalline materials, we illustrate in this paper how mechanical anisotropy has a profound effect on developing structures, such as crenulation cleavages, porphyroclast geometry and the initiation of shear bands and shear zones.

58 GEOSCIENCES↗

Imposing equilibrium on experimental 3-D stress fields using Hodge decomposition and FFT-based optimization

Here, we present a methodology to impose micromechanical constraints, i.e. stress equilibrium at grain and sub-grain scale, to an arbitrary (non-equilibrated) voxelized stress field obtained, for example, by means of synchrotron X-ray diffraction techniques. The method consists in finding the equilibrated stress field closest (in L 2 -norm sense) to the measured non-equilibrated stress field, via the solution of an optimization problem. The extraction of the divergence-free (equilibrated) part of a general (non-equilibrated) field is performed using the Hodge decomposition of a symmetric matrix field, which is the generalization of the Helmholtz decomposition of a vector field into the sum of an irrotational field and a solenoidal field. The combination of: a) the Euler–Lagrange equations that solve the optimization problem, and b) the Hodge decomposition, gives a differential expression that contains the bi-harmonic operator and two times the curl operator acting on the experimental stress field. These high-order derivatives can be efficiently performed in Fourier space. The method is applied to filter the non-equilibrated parts of a synthetic piecewise constant stress fields with a known ground truth, and stress fields in Gum Metal, a beta-Ti-based alloy measured in-situ using Diffraction Contrast Tomography (DCT). In both cases, the largest corrections were obtained near grain boundaries.

36 MATERIALS SCIENCE↗

Beam-pointing verification using x-ray pinhole cameras on the 60-beam OMEGA laser

On the OMEGA laser system, the beam-pointing accuracy is verified by irradiating a 4 mm diameter Au-coated spherical target with ~23 kJ of laser energy. Up to ten x-ray pinhole cameras record the x-ray emission from all 60-beam spots. A new set of algorithms has been developed to improve the accuracy of the pointing evaluation. An updated edge-finding procedure allows one to infer the center of the sphere with subpixel accuracy. A new approach was introduced to back-propagate the pixel locations on the 2D image to the 3D surface of the sphere. Furthermore, a fast Fourier transform-based de-noising method significantly improves the signal-to-noise of the data. Based on the beam-pointing analysis, hard-sphere calculations of the laser-drive illumination uniformity on the target surface and the decomposition of the illumination distribution into lower order modes (1–10) are evaluated.

47 OTHER INSTRUMENTATION↗

Improving OFDR Distributed Fiber Sensing by Fibers With Enhanced Rayleigh Backscattering and Image Processing

This article investigates using optical fibers with enhanced backscattering profiles to improve distributed fiber sensor performance and reduce instrumentation costs. Using a femtosecond (fs) laser direct writing technique, the Rayleigh backscattering profile of a standard telecom fiber was enhanced by more than 40 dB to improve the signal-to-noise ratio (SNR) for optical frequency domain reflectometry (OFDR). The enhanced backscattering signals enable effectively distributed strain measurements using a low-cost tunable laser (TL). Median filtering is applied to denoise cross correlation results to further improve measurement outcomes. Results presented in this article show that a TL with a 1-nm tuning range, which is far less than the tuning range used in commercial OFDR interrogators, can perform effectively distributed strain measurements using sensing fibers with enhanced backscattering profiles. The sensing fiber with over 40-dB backscattering enhancement achieved 4.8-cm spatial resolution in strain measurements with a root mean square accuracy of less than 2.70 με when 10–50 με were exerted to the sensing fiber. In conclusion, results presented in this article reveal both the potential and limitations of sensing fibers with enhanced backscattering for OFDR-based distributed fiber sensors.

42 ENGINEERING↗

Chapter 4: Physically informed deep learning networks for simulating microstructure evolution of 3D polycrystals

As discussed in the previous chapter, high energy diffraction microscopy (HEDM) is used to study the micromechanical evolution of a material during in situ loading. HEDM experiments have been used to verify crystal plasticity (CP) simulations [119, 91, 90, 120], for experimental planning, material design, and to further analyze experimental results. However, Fast Fourier transform-based CP (CP-FFT) or finite element-based CP (CP-FE) methods are often too slow to be used in real-time during an experiment. CP-FFT is faster than CP-FE simulations due to the absence of meshing, but can still take hours to simulate the response of a single volume depending on the size and number of strain steps [127]. Reducing computation time would create a larger exploration space in planning and design, and enable faster analysis of experimental results and real-time feedback during an experiment. This research expands upon previous works to develop a workflow for predicting the full-field evolution of a 3D polycrystal. The workflow is simplified from previous works to predict only orientation and elastic strain tensors (from which stress tensors are calculated). The network is physically informed through loss functions and network architecture for a more robust model. The orientation predictions are informed about the cubic crystal symmetry of the material by incorporating disorientation and misorientation information into the network architecture and loss. The Von Mises stress is used to enforce the correct stress-strain trends in the strain tensor predictions. Additional total strain steps from the elastic and elastoplastic region are included to better capture the stress-strain evolution at smaller total strain steps. Material and hardening parameters are additional inputs into the networks to further inform the network and to study the network’s ability to predict different materials other than those used for training.

36 MATERIALS SCIENCE↗

A numerical study of reversible plasticity using continuum dislocation mechanics

In this contribution, an elasto-viscoplastic fast Fourier transform-based (EVPFFT) numerical implementation of the Mesoscale Field Dislocation Mechanics (MFDM) formulation, called MFDM-EVPFFT, is applied to study the reversible plastic behavior of periodic two-phase crystalline composites with an elasto-viscoplastic plastic matrix and a purely elastic second phase. Additionally, periodic laminate microstructures of this kind with different periods (i.e. sizes) are considered to examine the size dependence of the Bauschinger effect and hardening during cyclic loading. Comparisons with classic composite effects obtained with conventional crystal plasticity are discussed. Specifically, the MFDM-EVPFFT results shed light on the hardening mechanisms due to piling-up/unpiling-up of geometrically-necessary dislocations (GND) during reverse loading.

36 MATERIALS SCIENCE↗