Search NASA⌕ Search

SEARCH · Search NASA

Results for “Grain microstructure evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Radiation induced hardening of beryllium during low temperature He implantation

The effect of ion irradiation on evolution of microstructure and hardening of beryllium with different impurity levels was investigated using TEM and nanoindentation. High purity S-65 grade and less-pure S-200-F grade were implanted by helium ions at temperatures of 50°C and 200°C. 11 different energies were used, so as to create a quasi-homogeneous 3 µm irradiated layer with average radiation damage of 0.1 dpa and average He content of 2000 appm.Nanoindentation experiments demonstrated that before irradiation, the S-200-F and S-65 grades have an average hardness of 3.7$\pm$0.8 GPa and 3.4$\pm$0.8 GPa correspondently. After implantation the hardness of both grades increased by about 60% for the 200°C irradiation and 100% for the 50°C irradiation. The crystallographic analysis of indented grains demonstrated that in the as-received materials the hardness is about 2.5 times higher when the indentation direction is close to the [0001] c-axis of beryllium compared to indentation perpendicular to [0001]. Hardness anisotropy significantly decreased after irradiation: the “soft orientation” was most sensitive to irradiation-induced hardening, with hardness increasing by about 140% after irradiation at 50°C and 100% after irradiation at 200°C, compared to about 15 - 20% for the “hard” orientation at both irradiation temperatures. The higher purity grade had smaller increase of the “soft orientation” hardness: 2.5$\pm$0.3 GPa for the S-65 and 2.9$\pm$0.2 GPa for the S-200-F.At both temperatures in both grades, under TEM investigation the radiation damage appears as “black dots” which are likely to be small dislocation loops with the number density of ~ 10 22 m -3 . No bubbles were observed by TEM inside grains and at grain boundaries. Analysis of the possible hardening contribution demonstrated that the observed “black dots” could be responsible for up to half of the measured hardening, while the rest of the hardening should originate from helium bubbles with the size below the TEM resolution (at or below 1.5 nm).

36 MATERIALS SCIENCE↗

Effect of Different Heat Treatments on the Microstructural Evolution and Mechanical Properties of Ni-Cr-Si Alloy Fabricated by Laser Additive Manufacturing

Ni-Cr-Si alloy samples were fabricated on mild steel via laser additive manufacturing technology. The microstructural evolution and mechanical properties of the samples were studied systematically in as-deposited conditions and under three different types of heat-treated conditions. The scanning electron microscopy, energy-dispersive x-ray spectroscopy and x-ray diffraction results showed that the structures of the as-deposited samples were mainly dendritic matrices of γ(Ni, Fe), continuous interdendritic eutectics of γ + Ni{sub 3}B and discrete Cr-rich carbides and borides. After solid solution treatment, carbides (Cr{sub 7}C{sub 3}) and borides (CrB) precipitated on the boundary of the eutectic structure, distributing discretely in the matrix. In the solution plus aging heat-treated conditions, the interdendritic eutectics formed Ni{sub 3}Fe intermetallic compounds with a layered distribution. After annealing, the grains were refined, and the hard phases (CrB) were uniformly dispersed along the grain boundary. Among the tested samples, the as-deposited specimens exhibited the highest microhardness and good wear ability at room temperature; however, the wear resistance of the as-deposited sample obviously decreased at 250 °C. The mechanical properties of the specimens were not greatly improved by solution treatment or solution plus aging treatment. The sample subjected to annealing treatment exhibited excellent wear resistance both at room temperature and at a service temperature of 250 °C.

36 MATERIALS SCIENCE↗

Formation and dissociation of shear-induced high-energy dislocations: insight from molecular dynamics simulations

Solid-phase processing (SPP) allows one to create complex microstructures, not achievable via thermal processing alone. The resulting structures exhibit a rich palette of defects, both thermal and non-thermal, including defect substructures, such as dislocation networks. It is essential to understand the mechanisms of deformation and defect structure formation to guide SPP towards achieving desired microstructures and material properties. In this study, large-scale molecular dynamics simulations are used to investigate the effects of inhomogeneous strain distribution, that mimics deformation conditions of tribological tests, on the evolution of defects under severe shear deformation in polycrystalline Al. Analysis of defect nucleation and reaction pathways reveals that strong geometric constraints suppress the nucleation and slide of low energy dislocation 1/2$\langle110\rangle${111} but promote the nucleation and slide of high energy dislocations, such as [$1\bar1$0] (001) and 1/2 [$1\bar1$$\bar2$]($1\bar1$1). Further, a rough contact surface, characteristic to tribological tests, imposes an inhomogeneous stress field leading to inhomogeneous defect substructures due to location-dependent activation of slip systems. The results suggest that high-energy dislocations can dominate the evolution of grain structures in highly constrained environments, which should be considered in modeling plastic deformation and grain refinement during SPP.

42 ENGINEERING↗

Effect of long-term aging on microstructure and local behavior in the heat-affected zone of a Ni–Cr–Mo–V steel welded joint

Evolution of microstructure, micro-hardness and micro-tensile strength behavior was investigated in the heat-affected zone of a Ni–Cr–Mo–V steel welded joint after the artificial aging at 350 °C for 3000 h. After detailed characterization of microstructures in optical microscopy, scanning electron microscopy and transmission electron microscopy, it is revealed that the change of martensite–bainite constituent promotes more homogeneous microstructure distribution. The aging treatment facilitates redistribution of carbon and chromium elements along the welded joint, and the micro-hardness is increased slightly through the welds due to enrichment of carbon. The types of precipitates in the weldment mainly include M{sub 3}C, MC, M{sub 2}C and M{sub 23}C{sub 6}. The carbides in base metal, weld metal and coarse-grained heat-affected zone are prone to change from ellipsoidal to platelet form whereas more uniform spherical carbides are observed in the fine-grained zone. Precipitation and coarsening of M{sub 23}C{sub 6} near the fusion line, and formation of MC and M{sub 2}C, are responsible for the tensile strength decrease and its smooth distribution in the aged heat-affected zone. This implies that the thermal aging can relieve strength mismatch in the weldments. - Highlights: • Microstructure homogeneity improved in HAZ after long-term aging. • Tensile strength decreased in HAZ due to precipitation and coarsening of M{sub 23}C{sub 6}. • Strength mismatch in NiCrMoV steel welds was relieved after aging at 350 °C × 3000 h.

36 MATERIALS SCIENCE↗

Modelling the evolution of complex conductivity during calcite precipitation on glass beads

When pH and alkalinity increase, calcite frequently precipitates and hence modifies the petrophysical properties of porous media. The complex conductivity method can be used to directly monitor calcite precipitation in porous media because it is sensitive to the evolution of the mineralogy, pore structure and its connectivity. Here, we have developed a mechanistic grain polarization model considering the electrochemical polarization of the Stern and diffuse layers surrounding calcite particles. Our complex conductivity model depends on the surface charge density of the Stern layer and on the electrical potential at the onset of the diffuse layer, which are computed using a basic Stern model of the calcite/water interface. The complex conductivity measurements of Wu et al. on a column packed with glass beads where calcite precipitation occurs are reproduced by our surface complexation and complex conductivity models. The evolution of the size and shape of calcite particles during the calcite precipitation experiment is estimated by our complex conductivity model. At the early stage of the calcite precipitation experiment, modelled particles sizes increase and calcite particles flatten with time because calcite crystals nucleate at the surface of glass beads and grow into larger calcite grains. Finally, at the later stage of the calcite precipitation experiment, modelled sizes and cementation exponents of calcite particles decrease with time because large calcite grains aggregate over multiple glass beads and only small calcite crystals polarize.

58 GEOSCIENCES↗

Study on the Microstructure, Mechanical Properties and Corrosion Behavior of Mg-Zn-Ca Alloy Wire for Biomaterial Application

Due to their excellent biocompatibility and biodegradability, magnesium alloy wires have attracted much attention for biomaterial applications including orthopedic K-wires and sutures in wound closure. In this study, Mg-3Zn-0.2Ca alloy wires were prepared by cold drawing combined with proper intermediate annealing process. Microstructures, texture, mechanical properties and corrosion behavior of Mg-3Zn-0.2Ca alloy wire in a simulated body fluid were investigated. The results showed that the secondary phase and average grain size of the Mg-3Zn-0.2Ca alloy were refined in comparison with the as-extruded alloy and a strong (0002)<10-10>//DD basal fiber texture system was formed after multi-pass cold drawing. After the annealing, most of the basal planes were tilted to the drawing direction (DD) by about 35°, presenting the characteristics of random texture, and the texture intensity decreased. The as-annealed wire shows good mechanical properties with the ultimate tensile strength (UTS), yield strength (YS) and elongation of 253 ± 8.5 MPa, 212 ± 11.3 MPa and 9.2 ± 0.9%, respectively. Electrochemical and hydrogen evolution measurements showed that the corrosion resistance of the Mg-3Zn-0.2Ca alloy wire was improved after the annealing. The immersion test indicated that the Mg-3Zn-0.2Ca wire exhibited uniform corrosion behavior during the initial period of immersion, but then exhibited local corrosion behavior.

36 MATERIALS SCIENCE↗

A finite element formulation for deformation twinning induced strain localization in polycrystal magnesium alloys

Deformation twinning induces shear strain localization in hexagonal close-packed crystals and is critical for the material’s ductility and failure. Cracks often occur at twin-twin or twin-grain boundary intersections and propagate along twin bands. However, most crystal plasticity models for deformation twinning are based on a “pseudo-slip” approach and do not capture the localized deformation associated with the formation of each discrete twin band. The few exceptions are discrete twin models that involve very complex numerical algorithms and are often compromised in accuracy due to the numerical convergence. These factors make the discrete twin models hard to adopt. This paper proposes a modification to the conventional finite element weak form, to fully incorporate a twin-induced heterogeneous deformation that does not depend on the “pseudo-slip” assumption. The model starts by splitting the deformation gradient into elastic-slip-twinning components. The twin-induced deformation gradient component is computed separately by solving a microstructural evolution problem and then implemented into finite element weak form by constructing a global “twin-force” vector. The constitutive update (e.g., in the user-defined material subroutine, or UMAT, for ABAQUS) therefore avoids dealing with the twinning and recovers to the form of a regular slip-based crystal plasticity model. The results presented here indicate that the twin-induced strain localization and the associated stress-reversal phenomena near the twin band were naturally captured in the model, which was validated against an in-situ synchrotron X-ray micro-diffraction experiment.

36 MATERIALS SCIENCE↗

Dynamic observation of dual-beam irradiated Fe and Fe-10Cr alloys at 435 °C

The attractive mechanical properties and superior resistance to void-swelling make ferritic/martensitic alloys a promising structural material for advanced nuclear reactors. However, one anomaly that has intrigued researchers for more than 50 years is the proportion of two types of dislocation loops in Fe and Fe-Cr alloys with Burger vectors b=½<111> and b=<100>. Although the possible mechanisms responsible for the presence of <100> loops continue to be the subject of intense modeling studies, there remains incomplete experimental understanding of fundamental irradiation processes in Fe(Cr) alloys. Here, the dose dependence of the irradiation-induced microstructural evolution was examined from 0 to 20 displacement per atom (dpa) in high purity Fe and Fe-10Cr during simultaneous dual-beam (1 MeV Kr + 10 appm He/dpa) irradiation at 435 °C. We experimentally revealed that the mechanism for the formation of <100> loops may not follow the conventional simple dislocation reaction between two 1½<111> loops. Real-time dynamic formation and evolution of defects including black dot loops, loop coarsening, loop decoration, network dislocations, and cavities were demonstrated. Several results indicated that the addition of Cr and He could impede dislocation loop motion. The evolution of the defect size/density and relative fraction of ½<111> vs <100> loops were quantitatively summarized. With increasing dose, ½<111> loops became the dominant type of loop in both materials. Notably, <100> loops were predominantly observed near grain boundaries only for pure Fe, while arrays of nanoscale black dot defects composing the <100> loop strings were observed in plenty in Fe-10Cr.

36 MATERIALS SCIENCE↗

Scale Invariance of Hot Spot Formation in TATB High Explosives

Shock-induced detonation of insensitive high explosives based on 1,3,5-triamino-2,4,6-trinitrobenzene starts with formation of hot spots at microstructural defects but has eluded atomistic modeling treatment at micron length scales. To this end, we performed multimicron scale all-atom molecular dynamics (MD) simulations of hot spots that form during the collapse of cylindrical pores with diameters between 10 and 300 nm. Our MD simulations show that hot spots formed at pores larger than 20 nm exhibit temperature fields with scale-invariant features for sizes up to at least 300 nm. Through a continuum-based grain-scale modeling framework, we span and extend beyond the size scales currently accessible to MD and find that hot spot scale invariance is a general feature that arises when the mechanical strength is insensitive to strain rate. Finally, our results demonstrate the applicability of all-atom MD to simulate the complicated dynamical evolution of micron-sized systems and bolster confidence in insights from MD simulations of materials that exhibit strength with negligible rate dependence over the relevant intervals.

36 MATERIALS SCIENCE↗

Visualizing Uranium Crystallization from Melt: Experiment-Informed Phase Field Modeling and Machine Learning

The focus of this project was to observe and simulate the solidification of uranium metal at the crystallographic level from its molten state. Melting experiments were conducted at two different scales to observe microstructural evolution using either a laboratory-scale induction furnace (hundreds of grams of metal) or a microscope heating stage (hundreds of milligrams of metal), respectively. Experimental parameters and characterization data were then used to inform a phase field model of gamma-U crystal growth as dendrites with or without secondary phase impurities in the form of uranium carbide particles. Finally, training datasets were generated by the phase field model as inputs to a neural network, developed with the aim of providing a faster, cheaper surrogate model for microstructural simulations within a given parameter space. Progress is reported herein for each of these task areas. Ultimately, 1) an optical microscope heating stage capability has been stood-up for uranium metal solidification studies, 2) a phase field model was advanced to simulate multiple uranium grains growing in the presence of carbide impurity particles and 3) a neural network was constructed and optimized to predict the microstructure features of individually growing uranium crystals.

36 MATERIALS SCIENCE↗

Microstructural Evolution and Mechanical Properties of Ti-22Al-25Nb (At.%) Orthorhombic Alloy with Three Typical Microstructures

Microstructural evolution, tensile and creep behavior of Ti-22Al-25Nb (at.%) orthorhombic alloy with three typical microstructures were investigated. The three typical microstructures were obtained by different solution and age treatment temperatures and analyzed by the BSE technique. The tensile strengths of the alloy at room temperature and 650 °C were investigated. The creep behaviors of the three typical microstructures were also studied at 650 °C/150 MPa for 100 h in air. The phase transformation mechanisms in creep deformation were also found. The experimental results showed that the formations of the three typical microstructures were decided by the isothermal forging and heat treatment. It was supposed that the high-temperature solution treatment might be dominant for the volume fraction and diameter of the equiaxed particles. While the double age treatment would lead to lamellar O phases. Due to grain refinement strengthening, the equiaxed microstructure presented the best tensile strength and ductility. The fully lamellar microstructure had the best creep resistance than that of other microstructures. In this paper, the phenomenon of creep-induced α{sub 2} phase decomposition was occurred during creep deformation of the equiaxed microstructure.

36 MATERIALS SCIENCE↗

Interpreting Electrochemical and Chemical Sodiation Mechanisms and Kinetics in Tin Antimony Battery Anodes Using in Situ Transmission Electron Microscopy and Computational Methods

Intermetallic compounds such as SnSb are promising anode materials for sodium ion batteries; however, their nanoscale sodiation mechanisms are not well understood. Here, we used a combination of in situ transmission electron microscopy (TEM), first-principles electronic structure calculations, computational thermodynamic modeling, and phase-field simulations to reveal the sodiation mechanisms and to quantify microstructural effects contributing to the underlying reaction kinetics in SnSb electrodes. During in situ sodiation experiments, the nanocrystalline SnSb thin films underwent a rapid amorphous phase transformation upon sodiation, as determined by in situ TEM and electron diffraction experiments. The Na + diffusion coefficients were measured with and without an external electrical bias, and the data showed that an applied potential increased Na + diffusion by an order of magnitude compared to solid-state diffusion. Furthermore, there was a distinct decrease in sodium diffusion upon the formation of the amorphous phase that resulted from a change in the local structure and grain boundaries. To further understand how the Na + transport mechanism correlated with the changes observed in the SnSb thin films, phase-field modeling was used, which considered sodium diffusion within the grain boundaries together with their evolution and stress–strain state. As a result, these findings enhance our understanding of sodiation mechanisms within intermetallic anode materials for sodium ion battery applications.

25 ENERGY STORAGE↗

Achieving Ultralow Wear with Stable Nanocrystalline Metals

Abstract Recent work suggests that thermally stable nanocrystallinity in metals is achievable in several binary alloys by modifying grain boundary energies via solute segregation. The remarkable thermal stability of these alloys has been demonstrated in recent reports, with many alloys exhibiting negligible grain growth during prolonged exposure to near‐melting temperatures. Pt–Au, a proposed stable alloy consisting of two noble metals, is shown to exhibit extraordinary resistance to wear. Ultralow wear rates, less than a monolayer of material removed per sliding pass, are measured for Pt–Au thin films at a maximum Hertz contact stress of up to 1.1 GPa. This is the first instance of an all‐metallic material exhibiting a specific wear rate on the order of 10 −9 mm 3 N −1 m −1 , comparable to diamond‐like carbon (DLC) and sapphire. Remarkably, the wear rate of sapphire and silicon nitride probes used in wear experiments are either higher or comparable to that of the Pt–Au alloy, despite the substantially higher hardness of the ceramic probe materials. High‐resolution microscopy shows negligible surface microstructural evolution in the wear tracks after 100k sliding passes. Mitigation of fatigue‐driven delamination enables a transition to wear by atomic attrition, a regime previously limited to highly wear‐resistant materials such as DLC.

Curry, John F.↗

Development of HPC based phase field simulations tool for modification of alloy morphology to enhance material properties during additive manufacturing (AM) process

Currently, additive manufacturing (AM) technology is extensively used to manufacture aerospace components because of the unique advantages of the technique in producing custom designs, complex geometries in a near-net fashion that significantly reduces the manufacturing cost, and improved energy efficiency. However, the thermodynamic properties of existing aerospace alloys and the thermal conditions that prevail in most of the powder-bed based additive manufacturing processes lead to undesirable columnar / columnar-dendritic microstructures that promote solidification cracking during the process, and the development of anisotropy in the mechanical properties of the as-built components. Time consuming, energy-intensive post AM treatments are required to recover the mechanical properties of the wrought components for which the existing alloy compositions were designed for. However, novel alloy compositions, that exploit the AM thermal conditions to produce fine, equiaxed grain structures in the as-built condition, with mechanical properties equal to or exceeding those of the wrought work-horse alloy, Ti-6Al-4V has recently been demonstrated in Ti-Cu alloys. Significant energy savings up to 66% can be obtained for a typical aerospace component through digitally designing the AM process, process parameters, and alloy composition. The current project focused on developing a fundamental understanding of the evolution of the columnar to equiaxed transition (CET) occurring during solidification under AM thermal conditions in Ti-Cu and Ti-Cu-X alloys using high-fidelity phase field (PF) simulations using the leadership class computing facilities that exist in the national laboratories. The simulations were able to capture the effect of alloy and process conditions on CET, and clearly showed the beneficial effect of a ternary solute addition to Ti-Cu binary alloys on CET. The simulations indicated that bulk nucleation in the liquid ahead of the solidifying epitaxial front was promoted by a large, transient, thermal undercooling promoted by the mismatch between the growth rate of the dendrite tips in the epitaxial front and the imposed solidification rate. AM experiments performed at Raytheon Technologies Research Center using the same thermal conditions used in the PF simulations indicated the formation of equiaxed grains, although the grain size was bigger than the ones reported in the literature. On the other hand, the equiaxed grain size predicted by PF simulations were smaller than the grain size of Ti-Cu alloys reported in the literature. The industry will follow up the existing work in a future program that would involve further optimization of the process for the Ti-Cu-X alloys to demonstrate the application of the process and the alloy to a specific aerospace component.

36 MATERIALS SCIENCE↗

Interpretation of Ion Irradiation and Neutron Irradiation Damage in Additively Manufactured 316 Stainless Steel using Multiscale Modeling

The accelerated adoption of nuclear energy necessitates advanced manufacturing technologies, such as additive manufacturing, to meet heightened supply chain requirements and support innovative reactor technologies. Due to the unique microstructural characteristics of additively manufactured materials under distinct solidification conditions, comprehensive evaluation of their performance in reactor environments is essential. The Advanced Materials and Manufacturing Technologies program under the Department of Energy's Office of Nuclear Energy focuses on understanding the irradiation performance and damage evolution of laser powder bed fusion 316 stainless steel, with an emphasis on integrating ion and neutron irradiation data to accelerate the development and qualification of materials for advanced nuclear reactor applications. While ion irradiation is a cost- and time-effective method, modeling and simulation are required to interpret the data for the broader range of irradiation conditions encountered in advanced reactors. In fiscal year 2025, integrated multiscale modeling and simulations were conducted to assess irradiation damage in additively manufactured 316 stainless steel. Key outcomes include predictions of chromium enrichment at grain boundaries, nickel enrichment at dislocation cell walls and void surfaces, and heterogeneous void evolution under ion and neutron irradiation conditions. Cluster dynamics simulations revealed the coarsening of voids at high irradiation temperatures and the suppression of void growth by high network dislocation density, while also demonstrating significant growth and coarsening of voids and self-interstitial atom loops at low dose rates. Machine learning-accelerated atomistic simulations highlighted the impact of the local environment and chromium concentration on vacancy diffusivity, providing key insights on the influence of composition on void swelling and radiation-induced segregation. Additionally, molecular dynamics simulations demonstrated the presence of defect production bias and a significant effect of carbon content on defect cluster behavior. These combined efforts aim to predict the performance of additively manufactured materials under various reactor conditions, supporting their qualification for nuclear reactor applications by interpreting ion irradiation data. This report underscores the potential of integrated multiscale modeling to analyze ion irradiation data in the effort to accelerate the qualification of additively manufactured materials for nuclear reactor components.

316 stainless steel↗

A crystal plasticity model incorporating the effects of precipitates in superalloys: Application to tensile, compressive, and cyclic deformation of Inconel 718

An elasto-plastic polycrystal plasticity model is developed and applied to an Inconel 718 (IN718) superalloy that was produced by additive manufacturing (AM). The model takes into account the contributions of solid solution, precipitates shearing, and grain size and shape effects into the initial slip resistance. Non-Schmid effects and backstress are also included in the crystal plasticity model for activating slip. The hardening law for the critical resolved shear stress is based on the evolution of dislocation density. In using the same set of material and physical parameters, the model is compared against a suite of compression, tension, and large-strain cyclic mechanical test data applied in different AM build directions. We demonstrate that the model is capable of predicting the particularities of both monotonic and cyclic deformation to large strains of the alloy, including decreasing hardening rate during monotonic loading, the non-linear unloading upon the load reversal, the Bauschinger effect, the hardening rate change during loading in the reverse direction as well as plastic anisotropy and the concomitant microstructure evolution. It is anticipated that the general model developed here can be applied to other multiphase alloys containing precipitates.

36 MATERIALS SCIENCE↗

Achieving Ultralow Wear with Stable Nanocrystalline Metals

Recent work suggests that thermally stable nanocrystallinity in metals is achievable in several binary alloys by modifying grain boundary energies via solute segregation. The remarkable thermal stability of these alloys has been demonstrated in recent reports, with many alloys exhibiting negligible grain growth during prolonged exposure to near-melting temperatures. In this paper, we show that PtAu, a proposed stable alloy consisting of two noble metals, exhibits extraordinary resistance to wear. Ultra-low wear rates, less than a monolayer of material removed per sliding pass, were measured for PtAu thin films at a maximum Hertz contact stress of up to 1.1 GPa. This is the first instance of an all-metallic material exhibiting a specific wear rate on the order of 10 -9 mm 3 /N-m, comparable to diamond-like carbon and sapphire. Remarkably, the wear rate of sapphire and silicon nitride probes used in wear experiments were either higher or comparable to that of the PtAu alloy, despite the substantially higher hardness of the ceramic probe materials. High-resolution microscopy showed negligible surface microstructural evolution in the wear tracks after 100k sliding passes. Finally, mitigation of fatigue-driven delamination enabled a transition to wear by atomic attrition, a regime previously limited to highly wear resistant materials such as diamond-like carbon.

36 MATERIALS SCIENCE↗

Structural Evolution of Layered Hybrid Lead Iodide Perovskites in Colloidal Dispersions

Controlling the structure of layered hybrid metal halide perovskites, such as the Ruddlesden-Popper (R-P) phases, is challenging because of their tendency to form mixtures of varying composition. Colloidal growth techniques, such as antisolvent precipitation, forms colloidal dispersions with properties that match bulk layered R-P phases, but controlling the composition of these particles remains challenging. Here, we explore the microstructure of particles of R-P phases of methylammonium lead iodide prepared by antisolvent precipitation from ternary mixtures of alkylammonium cations, where one cation can form perovskite phases (CH 3 NH 3 + ) and the other two promote layered structures as spacers (e.g. C 4 H 9 NH 3 + and C 12 H 25 NH 3 + ). We determine that alkylammonium spacers pack with constant methylene density in the R-P interlayer, and exclude interlayer solvent in dispersed colloids, regardless of length or branching. Using this result, we illustrate how the competition between cations that act as spacers between layers, or as grain- terminating ligands, determines the colloidal microstructure of layered R-P crystallites in solution. Optical measurements reveal that quantum well dimensions can be tuned by engineering the ternary cation composition. Transmission synchrotron wide-angle X-ray scattering and small angle neutron scattering reveal changes in the structure of colloids in solvent and after deposition into thin films. In particular, we find that spacers can alloy between R-P layers if they share common steric arrangements, but tend to segregate into polydisperse R-P phases if they do not mix. In conclusion, this study provides a framework to compare the microstructure of colloidal layered perovskites and suggests clear avenues to control phase and colloidal morphology.

14 SOLAR ENERGY↗