Search NASA⌕ Search

SEARCH · Search NASA

Results for “Process synthesis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Evolution of sputtered tungsten coatings at high temperature

Sputtered tungsten (W) coatings were investigated as potential high temperature nanophotonic material to replace bulk refractory metal substrates. Of particular interest are materials and coatings for thermophotovoltaic high-temperature energy conversion applications. For such applications, high reflectance of the substrate in the infrared wavelength range is critical in order to reduce losses due to waste heat. Therefore, the reflectance of the sputtered W coatings was characterized and compared at different temperatures. In addition, the microstructural evolution of sputtered W coatings (1 and 5 μm thick) was investigated as a function of anneal temperature from room temperature to 1000 °C. Using in situ x-ray diffraction analysis, the microstrain in the two samples was quantified, ranging from 0.33% to 0.18% for the 1 μm sample and 0.26% to 0.20% for the 5 μm sample, decreasing as the temperature increased. The grain growth could not be as clearly quantified due to the dominating presence of microstrain in both samples but was in the order of 20 to 80 nm for the 1 μm sample and 50 to 100 nm for the 5 μm sample, as deposited. Finally, the 5 μm thick layer was found to be rougher than the 1 μm thick layer, with a lower reflectance at all wavelengths. However, after annealing the 5 μm sample at 900 °C for 1 h, its reflectance exceeded that of the 1 μm sample and approached that of bulk W found in literature. Overall, the results of this study suggest that thick coatings are a promising alternative to bulk substrates as a low cost, easily integrated platform for nanostructured devices for high-temperature applications, if the problem of delamination at high temperature can be overcome.

36 MATERIALS SCIENCE↗

Experimental observation of Weyl points

The massless solutions to the Dirac equation are described by the so-called Weyl Hamiltonian. The Weyl equation requires a particle to have linear dispersion in all three dimensions while being doubly degenerate at a single momentum point. These Weyl points are topological monopoles of quantized Berry flux exhibiting numerous unusual properties. We performed angle-resolved microwave transmission measurements through a double-gyroid photonic crystal with inversion-breaking where Weyl points have been theoretically predicted to occur. The excited bulk states show two linear dispersion bands touching at four isolated points in the three-dimensional Brillouin zone, indicating the observation of Weyl points. Here, we pave the way to a variety of photonic topological phenomena in three dimensions.

14 SOLAR ENERGY↗

Characteristics of Molten Alloys as Anodes in Solid Oxide Fuel Cells

Molten alloys with 50-mol% In-Sb, Sn-Sb, Sb-Bi, and Sb-Pb were examined as anodes for solid oxide fuel cells at 973 K. The cells were operated in the battery mode, without added fuel, in order to understand the oxidation characteristics of these alloys at electrolyte interfaces. Cells using 50-mol% In-Sb and Sn-Sb mixtures exhibited open-circuit voltages (OCV) of 1.0 and 0.93 V, values that are identical to that of cell with pure In and Sn respectively. Also similar to the pure In and Sn anodes, the impedances of these cells were initially low but increased dramatically after drawing a small amount of charge, implying formation of In₂O₃ and SnO₂ layers at the electrolyte interface. The 50-mol% Sb-Bi cell had an OCV of 0.73 V initially, close to the OCV observed with pure Sb. The OCV remained constant until a charge identical to that required for oxidation of all the Sb had been passed, after which the OCV dropped to 0.43 V, similar to the value for pure Bi. SEM analysis of the cell after conversion of the Sb showed two distinct phases, with metallic Bi at the bottom and Sb₂O₃ at the top. The electrochemical oxidation of 50-mol% Sb-Pb alloys exhibited an OCV that changed continuously with conversion, from 0.73 V initially to 0.67 V following the addition of charge corresponding to oxidation of 120% the Sb. The total cell impedance remained low for this entire period. EDS measurements on the sectioned Sb-Pb cell suggested that both Sb and Pb were oxidized simultaneously to form a mixed oxide of Pb and Sb.

30 DIRECT ENERGY CONVERSION↗