Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reusable”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Future orbital transfer vehicle technology study. Volume 1: Executive summary

Reusable space and ground based LO2/LH2 OTV's, both advanced space engines and aero assist capability were compared. The SB OTV provided advantages in life cycle cost, performance and potential for improvement. An all LO2/LH2 OTV fleet was also compared with a fleet of LO2/.H2 OTV's and electric OTV's. The normal growth technology electric OTV used silicon cells with heavy shielding and argon ion thrusters. In this case, the LO2/LH2 OTV fleet provided a 23% advantage in total transportation cost. An accelerated technology LF2/LH2 OTV provided improvements in performance relative to LO2/.H2 OTV but has higher DDT&E cost which negated its cost effectiveness. The accelerated technology electric vehicle used GaAs cells and annealing but still did not result in the mixed fleet being any cheaper than an all LO2/LH2 OTV fleet. It is concluded that reusable LO2/LH2 OTV's can serve all general purpose cargo roles between LEO and GEO for the forseeable future. The most significant technology for the second generation vehicle would be space debris protection, on orbit propellant storage and transfer and on orbit maintenance capability.

Davis, E. E.↗
NASA NTRS1982

Assessment of Alternate Thermal Protection Systems for the Space Shuttle Orbiter

Candidate concepts are identified. The impact on the Shuttle Orbiter performance life cycle cost, and risk was assessed and technology advances required to bring the selected TPS to operational readiness are defined. The best system is shown to be a hybrid blend of metallic and carbon-carbon TPS concepts. These alternate concepts offer significant improvements in reusability and are mass competitive with the current ceramic tile reusable surface insulation. Programmatic analysis indicates approximately five years are required to bring the concepts to operational readiness.

Kelly, H. N.↗
NASA NTRS1982

Structural design of integral tankage for advanced space transportation systems

Fully reusable launch vehicle concepts being studied for post-Shuttle era transports present major challenges for the structural design of large propellant tankage. The dominant structural elements are internal tankage for both cryogenic and non-cryogenic propellants which must operate in a broad range of thermal environments while meeting requirements for low weight and reusability. Several approaches to integral tank design are discussed and an analysis of a hot structure honeycomb sandwich tank for a circular body vehicle is presented.

Macconochie, I. O.↗
NASA NTRS1983

SSME main combustion chamber life prediction

Typically, low cycle fatigue life is a function of the cyclic strain range, the material properties, and the operating temperature. The reusable life is normally defined by the number of strain cycles that can be accrued before severe material degradation occurs. Reusable life is normally signified by the initiation or propagation of surface cracks. Hot-fire testing of channel wall combustors has shown significant mid-channel wall thinning or deformation during accrued cyclic testing. This phenomenon is termed cyclic-creep and appears to be significantly accelerated at elevated surface temperatures. This failure mode was analytically modelled. The cyclic life of the baseline SSME-MCC based on measured calorimeter heat transfer data, and the life sensitivity of local hot spots caused by injector effects were determined. Four life enhanced designs were assessed.

Cook, R. T.↗
NASA NTRS1982

U.S. launch systems evolution

Shuttle improvements and Shuttle-derived vehicles which could answer projected launch system demands for the 1990s are explored. Traffic volume is suggested to be at levels exceeding the STS ability to deliver, thereby necessitating use of unmanned launch vehicles. Some payload delivery increase is possible using an Aft Cargo Carrier attached to the bottom of the external tank. This configuration would handle cargo with a diameter larger than the 15 ft allowable in the Orbiter bay. Various configurations of solid rocket booster cargo rockets are described, together with use of a module containing the Shuttle main engines and avionics as a recoverable part of a system able to place cargo 30 ft in diam and 90-100 ft tall in orbit. Using liquid reusable boosters would permit an increase of cargo capacity by the Shuttle of 50%, while a side-mount cargo vehicle (unmanned) offers a payload capacity of 165-200 klb. It is predicted that launch vehicles in the beginning of the 21st century will be of a fully reusable design.

Marshall, W. R.↗
NASA NTRS1983

In-flight load testing of advanced shuttle thermal protection systems

NASA Ames Research Center has conducted in-flight airload testing of some advanced thermal protection systems (TPS) at the Dryden Flight Research Center. The two flexible TPS materials tested, felt reusable surface insulation (FRSI) and advanced flexible reusable surface insulation (AFRSI), are currently certified for use on the Shuttle orbiter. The objectives of the flight tests were to evaluate the performance of FRSI and AFRSI at simulated launch airloads and to provide a data base for future advanced TPS flight tests. Five TPS configurations were evaluated in a flow field which was representative of relatively flat areas without secondary flows. The TPS materials were placed on a fin, the Flight Test fixture (FTF), that is attached to the underside of the fuselage of an F-104 aircraft. This paper describes the test approach and techniques used and presents the results of the advanced TPS flight test. There were no failures noted during post-flight inspections of the TPS materials which were exposed to airloads 40 percent higher than the design launch airloads.

Trujillo, B. M.↗
NASA NTRS1983

In-flight load testing of advanced thermal protection systems

NASA Ames Research Center has conducted in-flight airload testing of some advanced thermal protection systems (TPS) at the Dryden Flight Research Center. The two flexible TPS materials tested, felt reusable surface insulation (FRSI) and advanced flexible reusable surface insulation (AFRSI), are currently certified for use on the Shuttle orbiter. The objectives of the flight tests were to evaluate the performance of FRSI and AFRSI at simulated launch airloads and to provide a data base for future advanced TPS flight tests. Five TPS configurations were evaluated in a flow field which was representative of relatively flat areas without secondary flows. The TPS materials were placed on a fin, the Flight Test Fixture (FTF), that is attached to the underside of the fuselage of an F-104 aircraft. This paper describes the test approach and techniques used and presents the results of the advanced TPS flight test. There were no failures noted during post-flight inspections of the TPS materials which were exposed to airloads 40 percent higher than the design launch airloads.

Trujillo, B. M.↗
NASA NTRS1982

Space Shuttle/high energy upper stage capabilities for the 1990's

Possible performance gains and cost reductions available through the evolution of succeedingly larger unmanned, and then manned, orbital transfer vehicles (OTV) as Shuttle upper stages are projected. Future missions could include delivery of 10,000 lb to GEO, planetary missions in the 2000-12,000 lb class, 30-42 ft payloads in the 5000-10,000 lb class, and manned and unmanned satellite servicing by the turn of the century. The vehicles could evolve from the Centaur F vehicle through stages of all-propulsive configurations to aerobraked, fully reusable vehicles. Reusability introduces cost savings and the ability to make plane changes. Furthermore, aerobraking will double the payload capability for round trip journeys to GEO, bringing costs down to $7000/lb.

Teixeira, C.↗
NASA NTRS1985

Ground man-machine interfaces for orbiter checkout

The challenge of the concept of a reusable, cargo carrying space vehicle, and how those challenges were met for the Space Shuttle are discussed. The complexity of the vehicle, the ground support systen, the onboard computer system, ramifications of a reusable vehicle, and the turn around objectives for Shuttle flights are outlined. The Apollo and the space transportation system (STS) are compared.

Blackmon, F. H.↗
NASA NTRS1984

Aerojet advanced engine concept

The future orbit transfer vehicle (OTV) requirements which dictate the need for a highly versatile, highly reliable, reusable propulsion module are discussed. To attain maximum operational economy, space-basing is essential. This requires a reusable, maintenance free engine. The design features of this space based engine are defined. A new engine cycle and its advantages allow all the maintenance goals to be attained. Rubbing contact and interpropellant seals and purges are eliminated when GO2 is used to drive the LO2 pump. The TPA design has only one moving part. The use of both GH2 and GO2 to drive the turbines lowers the turbine temperatures in addition lower GH2 temperatures and pressures improve chamber cooling and longer life. The use of GO2 as a turbine drive fluid is addressed. Space based engines require an integrated control and health monitoring system to improve system reliability and eliminate all scheduled maintenance. It is concluded that all OTV propulsion requirements can be fulfilled with a single engine. The technological developments required to demonstrate that engine are outlined.

Schoenman, L.↗
NASA NTRS1985

An air-breathing ballistic space transporter for Europe

With increasing transport requirements, reusable space transporters again receive serious consideration in Europe as successors to the Ariane family. The paper deals with a hydrogen-ramjet-propelled, 1-1/2-stage reusable ballistic space transporter with vertical take-off and landing and using liquid hydrogen/oxygen rockets. This novel concept was developed in a theoretical study at the University of Stuttgart. The results are compared with recently published studies of several other European space transporter concepts. The data derived for the Istra - concept are: 15.4 Mg payload into low Earth-orbit, 155 Mg gross lift-off mass, 10% payload ratio, which represents a 57% propellant saving, and 44% reduction in dry mass (structure and engines) compared with comparable two-stage pure rocket concepts.

Kramer, P. A.↗
NASA NTRS1985

Heavy Lift Launch Vehicles for 1995 and Beyond

A Heavy Lift Launch Vehicle (HLLV) designed to deliver 300,000 lb to a 540 n mi circular polar orbit may be required to meet national needs for 1995 and beyond. The vehicle described herein can accommodate payload envelopes up to 50 ft diameter by 200 ft in length. Design requirements include reusability for the more expensive components such as avionics and propulsion systems, rapid launch turnaround time, minimum hardware inventory, stage and component flexibility and commonality, and low operational costs. All ascent propulsion systems utilize liquid propellants, and overall launch vehicle stack height is minimized while maintaining a reasonable vehicle diameter. The ascent propulsion systems are based on the development of a new liquid oxygen/hydrocarbon booster engine and liquid oxygen/liquid hydrogen upper stage engine derived from today's SSME technology. Wherever possible, propulsion and avionics systems are contained in reusable propulsion/avionics modules that are recovered after each launch.

Toelle, R.↗
NASA NTRS1986

Manned Mars mission vehicle design requirements for aerocapture

The goal of this study was to define vehicle design requirements of a reusable system for manned Mars missions which employ aerocapturlng techniques to obtain desired orbital velocities. Requirements for vehicle L/D and ballistic coefficient are determined for expected aerocapture velocities. This paper presents conclusions concerning g-loads environment and TPS requirements for a vehicle that aerocaptures at Mars and Earth. Although the goal of a reusable system (based on current state-of-art technologies) was not obtained, the viability of aerocapture at Mars and Earth was established.

Oliver Hill↗
NASA NTRS1986

Orbital transfer vehicle concept definition and system analysis study. Volume 1A: Executive summary. Phase 2

The objectives of the Phase 2 study were to improve the orbit transfer vehicle (OTV) concept definition by focusing on the following issues: the impact of mission requirements on OTV system design; OTV basing concepts on the Space Shuttle, separate platforms, and/or remote locations; cost reduction of an OTV program to improve its economic benefits and support its acquisition. The OTV mission scenario includes a wide range of missions the main drivers of which are manned GEO servicing, mid-inclination/polar DOD, and lunar/planetary projects. A mission model is presented which includes the type and number of missions per year and the estimated propellant requirements. To accomplish the missions, many OTV concepts were defined including ground-based OTVs launched either in the STS orbiter, the aft cargo carrier, or a heavy lift launch vehicle, and a space-based OTV. System and program trade studies were conducted using performance, cost, safety/risk, and operations/growth criteria. The study shows that mission requirements and substantial economic benefits justify a reusable, cryogenic (H2/O2) space-based OTV. Such a system would not be subjected to Earth-to-orbit launch loads and would not be constained in size or weight. Safety is enhanced by the fact that the system components are launched unfueled. Its inherent reusability and ability to be refueled in space make the space-based OTV very economical to operate.

Ketchum, W. J.↗
NASA NTRS1986

Potential directions for a second generation Space Shuttle

This paper reports on trends and potentials for advanced rocket vehicles which may be candidates for eventual phased replacement of the Shuttle. Although such a replacement need is not foreseen until 2002 at the earliest, due to the long time to develop a new vehicle its definition has already begun. The paper discusses the role of such a "Shuttle II' in the architecture of launch vehicles likely to exist in the post-2000 era, leading to its designation as a smaller, primarily passenger-carrying vehicle to complement large, unmanned cargo launch vehicles. While a two-stage glide-back fully reusable configuration is optimum for near-term technology, a single-stage-to-orbit reusable glide-back configuration is optimum for farther-term technology advances. For advanced technology which could be available in the mid-90s, such vehicle could orbit a payload weight equal to their own dry weight - a factor of 10 better than current launch vehicles.

Bekey, I.↗
NASA NTRS1986

A flight test challenge - Aeroassist for reuseable, space-based transportation

Attention is given to the challenges addressed by NASA in the development of reusable, space-based transportation systems which take advantage of aerobraking to achieve greater performance and overall efficiency. Aerobraking environmental factors associated with achieving higher energy reusable systems are outlined and the need for a coupled utilization of ground test capabilities and computational fluid dynamics (CFD) is demonstrated. It is concluded that the certification of CFD capability to provide the aerodynamic performance and aerothermodynamic environment for an aerobraking orbital transfer vehicle would be of major significance for the design and development of future flight systems.

Ried, Robert C.↗
NASA NTRS1987

Flight problem evaluation for Space Shuttle Orbiter

The flight problems experienced with the reusable Space Shuttle Orbiter have decreased during subsequent flights of each vehicle. By comparison to first flights of previous vehicles, the problems encountered on the initial flight of each new vehicle entering the fleet decreased. This improvement in turn has reduced the turnaround time between flights significantly and thus greatly enhanced the increased Space Shuttle launch frequency. The reusable manned space vehicle concept necessitated the development of a flight problem recognition and resolution system which would enable a thorough and timely vehicle turnaround flow. Flight evaluation, testing, and repair of manned spacecraft to enhance reliability and to ensure mission success is a unique activity. Real-time recognition of the flight problem, prompt isolation of the cause, and timely implementation of the corrective action are the keys to maintaining an operational fleet. Examples of flight problems that have been encountered as well as the corrective actions implemented during the first 24 Space Shuttle missions are presented. The corrective actions taken to preclude problem recurrence include modifications of hardware designs, manufacturing processes, flight software, test methods, and operational procedures.

Mechelay, Joseph E.↗
NASA NTRS1988

Cryogenic Insulation System

This invention relates to reusable, low density, high temperature cryogenic foam insulation systems and the process for their manufacture. A pacing technology for liquid hydrogen fueled, high speed aircraft is the development of a fully reusable, flight weight cryogenic insulation system for propellant tank structures. In the invention cryogenic foam insulation is adhesively bonded to the outer wall of the fuel tank structure. The cryogenic insulation consists of square sheets fabricated from an array of abutting square blocks. Each block consists of a sheet of glass cloth adhesively bonded between two layers of polymethacrylimide foam. Each block is wrapped in a vapor impermeable membrane, such as Kapton(R) aluminum Kapton(R), to provide a vapor barrier. Very beneficial results can be obtained by employing the present invention in conjunction with fibrous insulation and an outer aeroshell, a hot fuselage structure with an internal thermal protection system.

Davis, Randall C.↗