SEARCH · Search NASA

Results for “Structural simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

All sources NASA NTRS DOE OSTI

NASA NTRS2016

Composite Cure Process Modeling and Simulations using COMPRO(Registered Trademark) and Validation of Residual Strains using Fiber Optics Sensors

Composite cure process induced residual strains and warping deformations in composite components present significant challenges in the manufacturing of advanced composite structure. As a part of the Manufacturing Process and Simulation initiative of the NASA Advanced Composite Project (ACP), research is being conducted on the composite cure process by developing an understanding of the fundamental mechanisms by which the process induced factors influence the residual responses. In this regard, analytical studies have been conducted on the cure process modeling of composite structural parts with varied physical, thermal, and resin flow process characteristics. The cure process simulation results were analyzed to interpret the cure response predictions based on the underlying physics incorporated into the modeling tool. In the cure-kinetic analysis, the model predictions on the degree of cure, resin viscosity and modulus were interpreted with reference to the temperature distribution in the composite panel part and tool setup during autoclave or hot-press curing cycles. In the fiber-bed compaction simulation, the pore pressure and resin flow velocity in the porous media models, and the compaction strain responses under applied pressure were studied to interpret the fiber volume fraction distribution predictions. In the structural simulation, the effect of temperature on the resin and ply modulus, and thermal coefficient changes during curing on predicted mechanical strains and chemical cure shrinkage strains were studied to understand the residual strains and stress response predictions. In addition to computational analysis, experimental studies were conducted to measure strains during the curing of laminated panels by means of optical fiber Bragg grating sensors (FBGs) embedded in the resin impregnated panels. The residual strain measurements from laboratory tests were then compared with the analytical model predictions. The paper describes the cure process procedures and residual strain predications, and discusses pertinent experimental results from the validation studies.

Sreekantamurthy, Thammaiah↗

NASA NTRS2009

Shock Structure and Magnetic Fields Generation Associated with Relativistic Jets Unmagnetized Pair Plasma

Using 3D and 2D particle-in-cell simulations we investigate a shock structure, magnetic field generation, and particle acceleration associated with an unmagnetized relativistic electron-positron jet propagating into an unmagnetized pair plasma. The simulations use long computational grids which allow to study the formation and dynamics of the system in a spatial and temporal way. We find for the first time a relativistic shock system comparable to a predicted magnetohydrodynamic shock structure consisting of leading and trailing shocks separated by a contact discontinuity. Strong electromagnetic fields resulting from the Weibel two-stream instability are generated in the trailing shock where jet matter is thermalized and decelerated. We analyze the formation and nonlinear development through saturation and dissipation of those fields and associated particle acceleration. In the AGN context the trailing shock corresponds to the jet shock at the head of a relativistic astrophysical jet. In the GRB context this trailing shock can be identified with the bow shock driven by relativistic ejecta. The strong electromagnetic field region in the trailing shock provides the emission site for the hot spot at the leading edge of AGN jets and for afterglow emission from GRBs.

Niemiec, J.↗

NASA NTRS1981

Issues related to line-oriented flight training

The use of a training simulator along with carefully structured, detailed, line trip scenarios was envisioned by NASA as a means of providing a controllable, repeatable way to observe line crews in a highly realistic simulation of their working environment and obtain better understanding operationally significant human factors problems and issues. Relevant research done by the agency and the results of full-mission simulation scenarios revealed potential implications for flight training. Aspects to be considered in creating training programs closely related to the actual line environment with a total crew application in real world incident experiences include: (1) operational, environmental, equipment, and crew problems in scenario design; (2) real time line oriented flight training operation; (3) performance assessment and debriefing; (4) instructor qualification and training; and (5) other issues such as ub un initial, transition, and upgrade training; procedures developent and evaluation, and equipment evaluation.

Lauber, J. K.↗

NASA NTRS1990

A simulation survey of galaxy interactions

Many carefully selected samples of interacting galaxies have been observed extensively in attempts to clarify whether interaction produces activity in galaxies. Because the sample members represent a wide range of encounter parameters and times, one can then study whether there are correlations between observable encounter features and, for example, Seyfert activity. On the other hand, in theoretical studies, simulations typically deal with either time-consuming detailed modelling of single galaxy pairs or tracing a few model encounters over time. The authors extend the observational survey approach by combining it with a simulation survey. The authors are conducting a survey of model encounters, covering the most important encounter parameters over a wide range. Some parameters, such as companion structure and initial velocity, are demonstratably less important and can be ignored in a first pass. The parameter range must be richly enough sampled so that the authors can evaluate the uniqueness of the observable morphology and velocity structure of the resulting simulated pairs to diagnose unobservable companion orbit parameters. They are using a self-gravitating polar n-body code run on the Cray X-MP at the Alabama Supercomputer Network. For each simulation, the authors have stellar and gas distributions predicted over, typically, a billion years, along with information on gas motions within the disk and any material captured by the companion or lost to the system. Features of disturbed spiral galaxies are sensitive enough to time and encounter parameters so that a match of the simulation survey results to observations can be applied as starting points to infer unobservable orbital or system parameters in actual sample members. This should enable them to examine whether interesting observed properties (Seyfert activity, nuclear star-formation rate) are functions of unobservable dynamical properties which characterize each encounter. Any correlations (or lack of some expected ones) will provide strong clues as to how or whether these phenomena are related to interactions. Aside from its use with such observed samples, this survey should greatly speed determination of initial orbital parameters for more detailed subsequent simulations of individual systems.

Byrd, Gene G.↗

NASA NTRS2003

Biological Visualization, Imaging and Simulation(Bio-VIS) at NASA Ames Research Center: Developing New Software and Technology for Astronaut Training and Biology Research in Space

The Bio- Visualization, Imaging and Simulation (BioVIS) Technology Center at NASA's Ames Research Center is dedicated to developing and applying advanced visualization, computation and simulation technologies to support NASA Space Life Sciences research and the objectives of the Fundamental Biology Program. Research ranges from high resolution 3D cell imaging and structure analysis, virtual environment simulation of fine sensory-motor tasks, computational neuroscience and biophysics to biomedical/clinical applications. Computer simulation research focuses on the development of advanced computational tools for astronaut training and education. Virtual Reality (VR) and Virtual Environment (VE) simulation systems have become important training tools in many fields from flight simulation to, more recently, surgical simulation. The type and quality of training provided by these computer-based tools ranges widely, but the value of real-time VE computer simulation as a method of preparing individuals for real-world tasks is well established. Astronauts routinely use VE systems for various training tasks, including Space Shuttle landings, robot arm manipulations and extravehicular activities (space walks). Currently, there are no VE systems to train astronauts for basic and applied research experiments which are an important part of many missions. The Virtual Glovebox (VGX) is a prototype VE system for real-time physically-based simulation of the Life Sciences Glovebox where astronauts will perform many complex tasks supporting research experiments aboard the International Space Station. The VGX consists of a physical display system utilizing duel LCD projectors and circular polarization to produce a desktop-sized 3D virtual workspace. Physically-based modeling tools (Arachi Inc.) provide real-time collision detection, rigid body dynamics, physical properties and force-based controls for objects. The human-computer interface consists of two magnetic tracking devices (Ascention Inc.) attached to instrumented gloves (Immersion Inc.) which co-locate the user's hands with hand/forearm representations in the virtual workspace. Force-feedback is possible in a work volume defined by a Phantom Desktop device (SensAble inc.). Graphics are written in OpenGL. The system runs on a 2.2 GHz Pentium 4 PC. The prototype VGX provides astronauts and support personnel with a real-time physically-based VE system to simulate basic research tasks both on Earth and in the microgravity of Space. The immersive virtual environment of the VGX also makes it a useful tool for virtual engineering applications including CAD development, procedure design and simulation of human-system systems in a desktop-sized work volume.

Smith, Jeffrey↗

NASA NTRS1980

An approach to simulation of the finite element machine

The paper describes the simulation approach for the finite element machine (FEM), a special-purpose computer for structural analysis calculations under development at the NASA-Langley Research Center. The FEM consists of an array (1000 or more) of general-purpose microcomputers performing structural analysis in an asychronous parallel manner. A simulator of sufficient flexibility to model the behavior of the FEM on many levels has been designed and coded, and verification has begun using the experimental FEM hardware. The structure of the simulator is described, and preliminary simulation results are presented.

Sawyer, P. L.↗

NASA NTRS1989

Structural and metabolic characteristics of human skeletal muscle following 30 days of simulated microgravity

The effects of simulated microgravity (30 days of continuous 6-deg headdown bedrest, BR) on the structural and metabolic characteristics of human skeletal muscle were determined. Percutaneous needle biopsy samples obtained from the vastus lateralis and soleus muscles before and after the headdown BR were analyzed for histochemical, biochemical and ultrastructual changes. It was found that headdown BR led to decreases in both fast-twitch and slow-twitch fiber areas in both muscles, and there was evidence of remodeling of the ultrastructure in both muscles. The activities of beta-hydroxyacyl-CoA dehydrogenase and citrate synthase were reduced during BR, but phosphofructokinase and lactate dehydrogenase activities did not change. The results indicate that 30-d exposure to simulated microgravity decreased the capacity for aerobic energy supply of human skeletal muscle and led to a disorganization of the contractile machinery.

Hikida, Robert S.↗

NASA NTRS1988

Magnetic fine structure of solar coronal loops

A numerical simulation of the effect of a random photospheric flow on the magnetic structure of a coronal loop is presented. An initially uniform field embedded in a perfectly conducting plasma is assumed, extending between two flat parallel plates representing the solar photosphere at both ends of the loop. The field is perturbed by a sequence of randomly phased, sinusoidal flow patterns applied at one of the boundary plates, and the corresponding sequence of force-free fields is determined. It is found that the electric currents generated by these flows develop a fine structure on a scale significantly smaller than the wavelength of the velocity patterns. This suggests that magnetic energy is transferred to smaller scale via a cascade process.

Van Ballegooijen, A. A.↗

NASA NTRS1981

Pitfalls and guidelines for the numerical evaluation of moderate-order system frequency response

The design and evaluation of a feedback control system via frequency response methods relies heavily upon numerical methods. In application, one can usually develop low order simulation models which for the most part are devoid of numerical problems. However, when complex feedback interactions, for example, between instrument control systems and their flexible mounting structure, must be evaluated, simulation models become moderate to large order and numerical problems become common. A large body of relevant numerical error analysis literature is summarized in a large language understandable to nonspecialists. The intent is to provide engineers using simulation models with an engineering feel for potential numerical problems without getting intertwined in the complexities of the associated mathematical theory. Guidelines are also provided by suggesting alternate state of the art methods which have good numerical evaluation characteristics.

Frisch, H. P.↗

NASA NTRS2007

SRG110 Stirling Generator Dynamic Simulator Vibration Test Results and Analysis Correlation

The U.S. Department of Energy (DOE), Lockheed Martin (LM), and NASA Glenn Research Center (GRC) have been developing the Stirling Radioisotope Generator (SRG110) for use as a power system for space science missions. The launch environment enveloping potential missions results in a random input spectrum that is significantly higher than historical radioisotope power system (RPS) launch levels and is a challenge for designers. Analysis presented in prior work predicted that tailoring the compliance at the generator-spacecraft interface reduced the dynamic response of the system thereby allowing higher launch load input levels and expanding the range of potential generator missions. To confirm analytical predictions, a dynamic simulator representing the generator structure, Stirling convertors and heat sources were designed and built for testing with and without a compliant interface. Finite element analysis was performed to guide the generator simulator and compliant interface design so that test modes and frequencies were representative of the SRG110 generator. This paper presents the dynamic simulator design, the test setup and methodology, test article modes and frequencies and dynamic responses, and post-test analysis results. With the compliant interface, component responses to an input environment exceeding the SRG110 qualification level spectrum were all within design allowables. Post-test analysis included finite element model tuning to match test frequencies and random response analysis using the test input spectrum. Analytical results were in good overall agreement with the test results and confirmed previous predictions that the SRG110 power system may be considered for a broad range of potential missions, including those with demanding launch environments.

Lewandowski, Edward J.↗

NASA NTRS2006

SRG110 Stirling Generator Dynamic Simulator Vibration Test Results and Analysis Correlation

The U.S. Department of Energy (DOE), Lockheed Martin (LM), and NASA Glenn Research Center (GRC) have been developing the Stirling Radioisotope Generator (SRG110) for use as a power system for space science missions. The launch environment enveloping potential missions results in a random input spectrum that is significantly higher than historical RPS launch levels and is a challenge for designers. Analysis presented in prior work predicted that tailoring the compliance at the generator-spacecraft interface reduced the dynamic response of the system thereby allowing higher launch load input levels and expanding the range of potential generator missions. To confirm analytical predictions, a dynamic simulator representing the generator structure, Stirling convertors and heat sources was designed and built for testing with and without a compliant interface. Finite element analysis was performed to guide the generator simulator and compliant interface design so that test modes and frequencies were representative of the SRG110 generator. This paper presents the dynamic simulator design, the test setup and methodology, test article modes and frequencies and dynamic responses, and post-test analysis results. With the compliant interface, component responses to an input environment exceeding the SRG110 qualification level spectrum were all within design allowables. Post-test analysis included finite element model tuning to match test frequencies and random response analysis using the test input spectrum. Analytical results were in good overall agreement with the test results and confirmed previous predictions that the SRG110 power system may be considered for a broad range of potential missions, including those with demanding launch environments.

Suarez, Vicente J.↗

NASA NTRS2003

XML-Based Generator of C++ Code for Integration With GUIs

An open source computer program has been developed to satisfy a need for simplified organization of structured input data for scientific simulation programs. Typically, such input data are parsed in from a flat American Standard Code for Information Interchange (ASCII) text file into computational data structures. Also typically, when a graphical user interface (GUI) is used, there is a need to completely duplicate the input information while providing it to a user in a more structured form. Heretofore, the duplication of the input information has entailed duplication of software efforts and increases in susceptibility to software errors because of the concomitant need to maintain two independent input-handling mechanisms. The present program implements a method in which the input data for a simulation program are completely specified in an Extensible Markup Language (XML)-based text file. The key benefit for XML is storing input data in a structured manner. More importantly, XML allows not just storing of data but also describing what each of the data items are. That XML file contains information useful for rendering the data by other applications. It also then generates data structures in the C++ language that are to be used in the simulation program. In this method, all input data are specified in one place only, and it is easy to integrate the data structures into both the simulation program and the GUI. XML-to-C is useful in two ways: 1. As an executable, it generates the corresponding C++ classes and 2. As a library, it automatically fills the objects with the input data values.

Hua, Hook↗

NASA NTRS1990

Structural fatigue in the 34-meter HA-Dec antennas

Structural modifications to the 34-m hour-angle-declination antennas, coupled with the use of the antennas beyond their intended lifespans, have led to structural fatigue, as evidenced by damage to the declination drive gear and cracks on the structural members and gussets. An analysis and simulation were made of the main antenna structural members. The analysis showed that the total stress to the antenna structure substantially exceeds the maximum levels recommended by the American Institute of Steel Construction (AISC). Although each of the separate static conditions of stress is only 50 percent of the total stress and does not reach the AISC reduced yield limit, fatigue can and did occur, causing the material to crack in the weakest places.

Vanhek, R. A.↗

NASA NTRS1992

An experimental study of aeolian structures on Venus

Experiments to simulate the formation of aeolian bed forms on Venus show that a high-density atmosphere produces small transverse bed forms with dimensionless similarities to terrestrial dunes but with both dimensional and behavioral similarities to subaqueous current ripples. Their development is influenced by wind speed, particle size, and atmospheric density. Although aeolian bed forms should be observed at all elevations on Venus, their optimum expression is compatible with the lowest elevations where atmospheric pressure is greatest. Their development is relatively unhindered by the presence of dense grains, the lack of sorting in source sediment from which they form, or the addition of cohesive dust. Small (about 10 cm) bed forms are efficient in sorting materials either by density or particle size. Bed forms developed in the limited size of the wind tunnel are probably representative of small bed forms on Venus; considerations suggest that bed forms on Venus may grow to larger sizes. Discovery of dune fields on Magellan images of Venus support this prediction.

Marshall, John R.↗

NASA NTRS1997

An Initial Multi-Domain Modeling of an Actively Cooled Structure

A methodology for the simulation of turbine cooling flows is being developed. The methodology seeks to combine numerical techniques that optimize both accuracy and computational efficiency. Key components of the methodology include the use of multiblock grid systems for modeling complex geometries, and multigrid convergence acceleration for enhancing computational efficiency in highly resolved fluid flow simulations. The use of the methodology has been demonstrated in several turbo machinery flow and heat transfer studies. Ongoing and future work involves implementing additional turbulence models, improving computational efficiency, adding AMR.

Steinthorsson, Erlendur↗

NASA NTRS1995

High-Density Amorphous Ice, the Frost on Interstellar Grains

Most water ice in the universe is in a form which does not occur naturally on Earth and of which only minimal amounts have been made in the laboratory. We have encountered this 'high-density amorphous ice' in electron diffraction experiments of low-temperature (T less than 30 K) vapor-deposited water and have subsequently modeled its structure using molecular dynamics simulations. The characteristic feature of high-density amorphous ice is the presence of 'interstitial' oxygen pair distances between 3 and 4 A. However, we find that the structure is best described as a collapsed lattice of the more familiar low-density amorphous form. These distortions are frozen in at temperatures below 38 K because, we propose, it requires the breaking of one hydrogen bond, on average, per molecule to relieve the strain and to restructure the lattice to that of low-density amorphous ice. Several features of astrophysical ice analogs studied in laboratory experiments are readily explained by the structural transition from high-density amorphous ice into low-density amorphous ice. Changes in the shape of the 3.07 gm water band, trapping efficiency of CO, CO loss, changes in the CO band structure, and the recombination of radicals induced by low-temperature UV photolysis all covary with structural changes that occur in the ice during this amorphous to amorphous transition. While the 3.07 micrometers ice band in various astronomical environments can be modeled with spectra of simple mixtures of amorphous and crystalline forms, the contribution of the high-density amorphous form nearly always dominates.

Jenniskens, P.↗

NASA NTRS2002

Propulsion Simulations with the Unstructured-Grid CFD Tool TetrUSS

A computational investigation has been completed to assess the capability of the NASA Tetrahedral Unstructured Software System (TetrUSS) for simulation of exhaust nozzle flows. Three configurations were chosen for this study: (1) a fluidic jet effects model, (2) an isolated nacelle with a supersonic cruise nozzle, and (3) a fluidic pitchthrust- vectoring nozzle. These configurations were chosen because existing data provided a means for measuring the ability of the TetrUSS flow solver USM3D for simulating complex nozzle flows. Fluidic jet effects model simulations were compared with structured-grid CFD (computational fluid dynamics) data at Mach numbers from 0.3 to 1.2 at nozzle pressure ratios up to 7.2. Simulations of an isolated nacelle with a supersonic cruise nozzle were compared with wind tunnel experimental data and structured-grid CFD data at Mach numbers of 0.9 and 1.2, with a nozzle pressure ratio of 5. Fluidic pitch-thrust-vectoring nozzle simulations were compared with static experimental data and structured-grid CFD data at static freestream conditions and nozzle pressure ratios from 3 to 10. A fluidic injection case was computed with the third configuration at a nozzle pressure ratio of 4.6 and a secondary pressure ratio of 0.7. Results indicate that USM3D with the S-A turbulence model provides accurate exhaust nozzle simulations at on-design conditions, but does not predict internal shock location at overexpanded conditions or pressure recovery along a boattail at transonic conditions.

Deere, Karen A.↗

NASA NTRS1994

Correlations in cosmic density fields

A method is proposed to place constraints on the functional form of the high-order correlation functions zeta(sub n) that arise in cosmic density fields at large scales. This technique is based on a mass-in-cell statistic and a difference of mass in partitions of a cell. The relationship between these measures is sensitive to the formal structure of the zeta(sub n) as well as their amplitudes. This relationship is quantified in several theoretical models of structure, based on the hierarchical clustering paradigm. The results lead to a test for specific types of hierarchical clustering that is sensitive to correlations of all orders. The method is applied to examples of simulated large-scaled structure dominated by cold dark matter. In the preliminary study, the hierarchical paradigm appears to be a realistic approximation over a broad range of the scales. Furthermore, there is evidence that graphs of low-order vertices are dominant. On the basis of simulated data a phenomological model is specified that gives a good representation of clustering from linear scales to the strongly clustered regime (zeta(sub 2) approximately 500).

Bromley, B. C.↗