Search NASA⌕ Search

SEARCH · Search NASA

Results for “Traffic simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Investigation of air transportation technology at Princeton University, 1988-1989

The Air Transportation Technology Program at Princeton University, a program emphasizing graduate and undergraduate student research, proceeded along several avenues during the past year. A study of optimal trajectories for penetration of microbursts when encounter is unavoidable was conducted. The emphasis of current wind shear research is on developing an expert system for wind shear avoidance. A knowledge-based reconfigurable flight control system that is implemented with the Pascal programming language using parallel microprocessors was developed. This expert system could be considered a prototype for a failure-tolerant control system that can be constructed using existing hardware. Development of a real-time cockpit simulator continued during the year. The simulator provides a single-person crew station with both conventional and advanced control devices; it currently is programmed to simulate the Navion single-engine general aviation airplane. Alternatives for the air traffic control system giving particular attention to the institutional structure of the FAA are analyzed. A simple numerical procedure for estimating the stochastic robustness of control systems is being investigated. The revitalization of the general aviation industry is also discussed.

Stengel, Robert F.↗

SATS HVO Concept Validation Experiment

A human-in-the-loop simulation experiment was conducted at the NASA Langley Research Center s (LaRC) Air Traffic Operations Lab (ATOL) in an effort to comprehensively validate tools and procedures intended to enable the Small Aircraft Transportation System, Higher Volume Operations (SATS HVO) concept of operations. The SATS HVO procedures were developed to increase the rate of operations at non-towered, non-radar airports in near all-weather conditions. A key element of the design is the establishment of a volume of airspace around designated airports where pilots accept responsibility for self-separation. Flights operating at these airports, are given approach sequencing information computed by a ground based automated system. The SATS HVO validation experiment was conducted in the ATOL during the spring of 2004 in order to determine if a pilot can safely and proficiently fly an airplane while performing SATS HVO procedures. Comparative measures of flight path error, perceived workload and situation awareness were obtained for two types of scenarios. Baseline scenarios were representative of today s system utilizing procedure separation, where air traffic control grants one approach or departure clearance at a time. SATS HVO scenarios represented approaches and departure procedures as described in the SATS HVO concept of operations. Results from the experiment indicate that low time pilots were able to fly SATS HVO procedures and maintain self-separation as safely and proficiently as flying today's procedures.

Consiglio, Maria↗

Collision Avoidance for Airport Traffic Concept Evaluation

An initial Collision Avoidance for Airport Traffic (CAAT) concept for the Terminal Maneuvering Area (TMA) was evaluated in a simulation study at the National Aeronautics and Space Administration (NASA) Langley Research Center. CAAT is being designed to enhance surface situation awareness and provide cockpit alerts of potential conflicts during runway, taxi, and low altitude air-to-air operations. The purpose of the study was to evaluate the initial concept for an aircraft-based method of conflict detection and resolution (CD&R) in the TMA focusing on conflict detection algorithms and alerting display concepts. This paper gives an overview of the CD&R concept, simulation study, and test results.

Jones, Denise R.↗

ATM Technology Demonstration 1 (ATD-1) Project: Terminal Airspace Technologies for NextGen (Public)

This video highlights the human-in-the-loop (HITL) simulations conducted by the ATD-1 project and features visual elements developed for Traffic Management Advisor - Terminal Metering, Controller Managed Spacing, and Flight Deck Interval Management. The video content is fairly technical and intended for audiences that have some knowledge of air traffic management issues. This includes researchers and management from NASA, FAA, industry partners, and others interested in terminal metering, controller managed spacing, and interval management technologies. Please note that the media release only clears the video for peer audiences such as ATM conferences or as part of presentations to researchers.

Robinson, John E.↗

Detect-and-Avoid Alerting Performance for High-Speed UAS and Non-Cooperative Aircraft

This paper presents a set of experiments designed to assess the viability of using a smaller Detect and Avoid (DAA) volume for large Unmanned Aircraft Systems (UAS) when they are trying to remain well clear of non-cooperative visual flight rules (VFR) aircraft, in compliance with Federal regulations. The current DAA volume was defined for both cooperative and non-cooperative VFR traffic by the work of RTCA Special Committee 228 in 2017, in what is referred to in this paper as the Phase 1 standards. Subsequent work by the committee has been focused on enabling operations by smaller UAS that cannot carry the heavy radars required for the Phase 1 DAA Minimum Operational Performance Standards (MOPS). The work discussed in this paper will explore whether a Phase 1 UAS using a Phase 1 radar can use the reduced non-cooperative DAA alerting volume being studied for smaller, slower Phase 2 UAS without significantly degrading system safety. The study uses UAS models and background traffic from previous Phase 1 and Phase 2 research to run an unmitigated simulation that will examine alerting performance using different DAA well clear definitions. The primary metrics are also tied to the alerting performance of the DAA system, and include average alerting times, probabilities of missed and late alerts, and the probability of a near mid-air collision given a loss of "well clear," as defined by the DAA system. Results are expected to help RTCA make the determination whether or not the DAA well clear definition for Phase 1 UAS can be reduced for non-cooperative VFR aircraft.

Cone, Andrew C.↗

Detect-and-Avoid Alerting Performance for High-Speed UAS and Non-Cooperative Aircraft

This paper presents a set of experiments designed to assess the viability of using a smaller Detect and Avoid (DAA) volume for large Unmanned Aircraft Systems (UAS) when they are trying to remain well clear of non-cooperative visual flight rules (VFR) aircraft, in compliance with Federal regulations. The current DAA volume was defined for both cooperative and non-cooperative VFR traffic by the work of RTCA (Radio Technical Commission for Aeronautics) Special Committee 228 in 2017, in what is referred to in this paper as the Phase 1 standards. Subsequent work by the committee has been focused on enabling operations by smaller UAS that cannot carry the heavy radars required for the Phase 1 DAA Minimum Operational Performance Standards (MOPS). The work discussed in this paper will explore whether a Phase 1 UAS using a Phase 1 radar can use the reduced non-cooperative DAA alerting volume being studied for smaller, slower Phase 2 UAS without significantly degrading system safety. The study uses UAS models and background traffic from previous Phase 1 and Phase 2 research to run an unmitigated simulation that will examine alerting performance using different DAA well clear definitions. The primary metrics are also tied to the alerting performance of the DAA system, and include average alerting times, probabilities of missed and late alerts, and the probability of a near mid-air collision given a loss of "well clear," as defined by the DAA system. Results are expected to help RTCA make the determination whether or not the DAA well clear definition for Phase 1 UAS can be reduced for non-cooperative VFR aircraft.

UAS↗

Modeling and simulation of the data communication network at the ASRM Facility

This paper describes the modeling and simulation of the communication network for the NASA Advanced Solid Rocket Motor (ASRM) facility under construction at Yellow Creek near Luka, Mississippi. Manufacturing, testing, and operations at the ASRM site will be performed in different buildings scattered over an 1800 acre site. These buildings are interconnected through a local area network (LAN), which will contain one logical Fiber Distributed Data Interface (FDDI) ring acting as a backbone for the whole complex. The network contains approximately 700 multi-vendor workstations, 22 multi-vendor workcells, and 3 VAX clusters interconnected via Ethernet and FDDI. The different devices produce appreciably different traffic patterns, each pattern will be highly variable, and some patterns will be very bursty. Most traffic is between the VAX clusters and the other devices. Comdisco's Block Oriented Network Simulator (BONeS) has been used for network simulation. The two primary evaluation parameters used to judge the expected network performance are throughput and delay.

Nirgudkar, R. P.↗

Evaluation of an Arrival Coordinator Position in a Terminal Metering Enviornment

NASA has developed an integrated arrival-management solution for terminal area precision scheduling (TAPSS). Ahuman-in-the-loop simulation investigated the performance of the components of the TAPSS system. The focus ofthis paper is set on the terminal radar approach control (TRACON) traffic management controller (TMC) and ArrivalRadar Coordinator (ARC) combined position, which played an integral part in coordinating, adjusting, and instantiatingthe arrival schedule computed by the TAPSS system. Analysis of the simulation data highlights the roleof the ARC within the described terminal metering environment, describes his planning strategies, the interactionswith his tools and coordination with controllers, and lends insights to the impact of the ARCs actions to the arrivalproblem. High levels of comfort and confidence were reported when working with the TAPSS system. Challengesposed the sequencing of unscheduled satellite arrival flights during periods of peak demand. To accommodate thoseflights into the arrival stream, the ARC had to identify sequence slots, while minimizing disruptions to the schedule.

terminal metering↗

Modeling and Simulating Airport Surface Operations with Gate Conflicts

The Surface Operations Simulator and Scheduler (SOSS) is a fast-time simulation platform used to develop and test future surface scheduling concepts such as NASAs Air Traffic Demonstration 2 of time-based surface metering at Charlotte Douglas International Airport (CLT). Challenges associated with CLT surface operations have driven much of SOSS development. Recently, SOSS functionality for modeling hardstand operations was developed to address gate conflicts, which occur when an arrival and departure wish to occupy the same gate at the same time. Because surface metering concepts such as ATD2 have the potential to increase gates conflicts as departure are held at their gates, it is important to study the interaction between surface metering and gate conflict management. Several approaches to managing gate conflicts with and without the use of hardstands were simulated and their effects on surface operations and scheduler performance compared.

Zelinski, Shannon↗

Assistive Detect and Avoid for Pilots in the Cockpit

Aircraft not receiving radar services rely on see and avoid and radio coordination via Common Traffic Advisory Frequencies to remain well clear of each other and avoid mid-air collisions. Radio coordination is usually performed in the vicinity of non-towered airports whereas non-radar services en-route operations rely solely on see and avoid. This paper presents the results of a simulation study of the effectiveness of assistive detect and avoid technologies when used to enhance pilots’ ability to see and avoid nearby traffic. Three different experimental conditions are modeled, representing “unaided see and avoid”, “see and avoid with traffic advisories”, and “see and avoid with assistive detect and avoid technology”. The effectiveness of see and avoid is evaluated using a set of head-on, crossing, and overtaking encounter scenarios and a model of visual acquisition embedded in a Monte Carlo simulation. The effectiveness of assistive detect and avoid is estimated for the same encounter scenarios. A prototype system for detect and avoid and a summary of results are presented. Preliminary results strongly suggest that assistive detect and avoid could greatly enhance the capabilities of flight crews to avoid traffic and remain well clear.

collision, detect and avoid, resolution, well clea↗

Assistive Detect and Avoid for Pilots in the Cockpit

Aircraft not receiving radar services rely on see and avoid and radio coordination via Common Traffic Advisory Frequencies to remain well clear of each other and avoid mid-air collisions. Radio coordination is usually performed in the vicinity of non-towered airports whereas non-radar services en-route operations rely solely on see and avoid. This paper presents the results of a simulation study of the effectiveness of assistive detect and avoid technologies when used to enhance pilots’ ability to see and avoid nearby traffic. Three different experimental conditions are modeled, representing “unaided see and avoid”, “see and avoid with traffic advisories”, and “see and avoid with assistive detect and avoid technology”. The effectiveness of see and avoid is evaluated using a set of head-on, crossing, and overtaking encounter scenarios and a model of visual acquisition embedded in a Monte Carlo simulation. The effectiveness of assistive detect and avoid is estimated for the same encounter scenarios. A prototype system for detect and avoid and a summary of results are presented. Preliminary results strongly suggest that assistive detect and avoid could greatly enhance the capabilities of flight crews to avoid traffic and remain well clear.

collision↗

Investigating the Impact of Connected Vehicle Market Share on the Performance of Reinforcement-Learning Based Traffic Signal Control

We aim to understand and explore the performance of reinforcement learning based signal control algorithms in a mixed environment with less than 100% market share of connected and automated vehicles (CAVs). Within a simulation environment, we have considered partial connectivity—less than 100% market share of CAVs—in the network and investigated the impact on the performance of the signal control algorithm. Two test networks including a four-intersection arterial in Lankershim Boulevard, CA, and a portion of downtown Springfield, IL, with 20 intersections. The first network is calibrated in the micro-simulator PTV Vissim with the US DOT provided NGSIM datasets. The results provide insights regarding the impact of the connectivity and sensing technologies on the practical implementation of traffic signal control algorithms that leverage the data sharing capability of a connected environment. For scenarios with 40% or more market share of CAVs, we observed improvement in the performance metrics—travel time, queue time, and energy consumption—with the increase in market share. Results from our experiments do not indicate any clear trend when the networks have low (less than 40%) market share of CAVs. The higher standard deviations as obtained from the statistical analyses of the performance metrics at low market share may indicate the instability of the RL controller arising from the partial (if not zero) observability of the traffic states. Further, we have conducted simplified scenario analyses to explore the impact of the market share of battery electric vehicles (BEVs) on energy consumption due to the regenerative braking feature. Our results and findings will be the foundation for the future reinforcement learning based control algorithm development that accounts for partial connectivity—less than 100% CAV market share, and the presence of BEVs in a network of connected and automated signalized intersections.

33 ADVANCED PROPULSION SYSTEMS↗

Multi-media authoring - Instruction and training of air traffic controllers based on ASRS incident reports

This paper discusses the use of computer-assisted instructions and flight simulations to enhance procedural and perceptual motor task training. Attention is called to the fact that incorporating the accident and incident data contained in reports filed with the Aviation Safety Reporting System (ASRS) would be a valuable training tool which the learner could apply for other situations. The need to segment the events is emphasized; this would make it possible to modify events in order to suit the needs of the training environment. Methods were developed for designing meaningful scenario development on runway incursions on the basis of analysis of ASRS reports. It is noted that, while the development of interactive training tools using the ASRS and other data bases holds much promise, the design and production of interactive video programs and laser disks are very expensive. It is suggested that this problem may be overcome by sharing the costs of production to develop a library of materials available to a broad range of users.

Armstrong, Herbert B.↗

A Computer Simulation of the System-Wide Effects of Parallel-Offset Route Maneuvers

Most aircraft managed by air-traffic controllers in the National Airspace System are capable of flying parallel-offset routes. This paper presents the results of two related studies on the effects of increased use of offset routes as a conflict resolution maneuver. The first study analyzes offset routes in the context of all standard resolution types which air-traffic controllers currently use. This study shows that by utilizing parallel-offset route maneuvers, significant system-wide savings in delay due to conflict resolution of up to 30% are possible. It also shows that most offset resolutions replace horizontal-vectoring resolutions. The second study builds on the results of the first and directly compares offset resolutions and standard horizontal-vectoring maneuvers to determine that in-trail conflicts are often more efficiently resolved by offset maneuvers.

Lauderdale, Todd A.↗

Automated Scenario Generation for Human-in-the-Loop Simulations

Automated Multi-Aircraft Control System scenario generation for Human-in-the-Loop (HITL) evaluations of air traffic management concepts is described. The objective is to replace the difficult manual process with the automated process for creating an initial (seed) scenario that serves as a starting point for manual adjustments for creating the Human-in-the-Loop scenario. Methods for analyzing and comparing the seed-scenario generated using the automated process and the Human-in-the-Loop-scenario derived from it to meet the experiment objectives are discussed. Results of comparison of input Human-in-the-Loop-scenario with the Multi-Aircraft Control System output are also presented. The main findings are: (1) many of the characteristics of the seed-scenario used for constructing the Human-in-the-Loop-scenario are preserved in the Human-in-the-Loop-scenario, (2) landing rate profile of the traffic generated by the Multi-Aircraft Control System (MACS) using the input scenario compares reasonably well with that intended in the input scenario, and (3) many of the desired characteristics of the Human-in-the-Loop-scenario can be achieved by further automation.

Automated Scenario Generation↗

Comparison of Different Control Schemes for Strategic Departure Metering

Airports and their terminal airspaces are key choke points in the air transportation system causing major delays and adding to pollution. A solution aimed at mitigating these chokepoints integrates the scheduling of runway operations, flight release from the gates and ramp into the airport movement area, and merging with other traffic competing for downstream airspace points. Within this integrated concept, we present a simulation-based analysis of the departure metering process, which delays the release of flights into the airport movement area while balancing two competing objectives: (1) maintaining large enough queues at the airport resources to maximize throughput and (2) absorbing excess delays at the gates or in ramp areas to save on fuel consumption, emissions, noise, and passenger discomfort. Three metering strategies are compared which respectively attempt to control the number of flights that (1) left the gate but did not take off, (2) left the ramp but did not take off, and (3) spent their unimpeded transit time to the runway but did not take off. It was observed that under deterministic and demand uncertainty conditions, the first strategy performed better than the other two strategies in terms of maintaining the runway throughput while transferring a significant average delay of two minutes to the gate. On the other hand, under uncertainties of flight transit time and runway service rate, all the strategies struggled to delay flights at the gate without a significant impact on the runway throughput.

air traffic management↗

Optimal Power Sharing Speed Compensation in On-road Wireless EV Charging Systems

Dynamic wireless charging of electric vehicles (EV) is an emerging technology with the potential to address range anxiety and reduce the size of batteries or provide charge-sustaining operation. Charging demand for dynamic wireless charging systems (DWCS) varies greatly in response to location-specific traffic behaviors including the number and speed of vehicles. This paper highlights the potential reduction of load variation with speed compensation and simulates opportunities to maximize the number of cars charged concurrently through “power sharing” or altering power output to slower cars while maintaining a maximum delivered energy. An improved sub-minute model for synthetic traffic is proposed to effectively model DWCS load on high speed roadways and a power electronics model is created based on an existing prototype developed by ORNL to investigate the potential for power sharing. Reductions in the average speed of traffic can greatly increase instantaneous DWCS load by as much as 26%, complicating capacity sizing. Parametric studies with a LCC-S power electronics model shows feasible power reduction of more than 20%, while maintaining a maximum achievable efficiency greater than 90%. Speed compensation on a roadway with large speed variation can reduce average power expected by 21% and increase the maximum number of cars charged simultaneously by 30%. The application of power sharing may significantly reduce load variability due to speed, allow for increased car hosting capability, and guarantee a maximum energy delivered.

Lewis, Donovin D.↗

An interactive driving simulation for driver control and decision-making research

Display techniques and equations of motion for a relatively simple fixed base car simulation are described. The vehicle dynamics include simplified lateral (steering) and longitudinal (speed) degrees of freedom. Several simulator tasks are described which require a combination of operator control and decision making, including response to wind gust inputs, curved roads, traffic signal lights, and obstacles. Logic circuits are used to detect speeding, running red lights, and crashes. A variety of visual and auditory cues are used to give the driver appropriate performance feedback. The simulated equations of motion are reviewed and the technique for generating the line drawing CRT roadway display is discussed. On-line measurement capabilities and experimenter control features are presented, along with previous and current research results demonstrating simulation capabilities and applications.

Allen, R. W.↗