Search NASA⌕ Search

SEARCH · Search NASA

Results for “ceramic processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Evaluation of High Temperature Plastics as a Ceramic Replacement

This report describes the 2015-2017 fiscal year research efforts to evaluate high temperature plastics as replacement materials for ceramics in electrical contact assemblies. The main objective of this work was to assess the feasibility of replacing existing high-price ceramic inserts with a polymeric material. Current ceramic parts are expensive due to machining costs and can suffer brittle failure. Therefore, replacing the ceramic with a more cost-effective material — in this case a plastic — is highly desirable. Not only are plastics easier to process, but they can also eliminate final tooling and are less brittle than ceramics. This effort used a three-phase approach: selection of appropriate materials determined by a comprehensive literature review, performance of an initial thermal stability screening, understanding of aging behavior under normal and off-normal conditions, and evaluation of performance at elevated temperatures. Two polymers were determined to meet the desired criteria: polybenzimidazole, and Vespel® SP-1 polyimide. Polymer derived ceramics may also be useful but will require further development of molding capabilities that were beyond the scope of this program.

36 MATERIALS SCIENCE↗

Near infrared quantum cutting in heavy Yb doped Ce{sub 0.03}Yb{sub 3x}Y{sub (2.97-3x)}Al{sub 5}O{sub 12} transparent ceramics for crystalline silicon solar cells

Near infrared (NIR) quantum cutting involving the conversion of an absorbed blue photon into two NIR photons emission has been realized in heavy Yb doped Ce{sub 0.03}Yb{sub 3x}Y{sub (2.97-3x)}Al{sub 5}O{sub 12} (x=0.1, 0.25, and 0.5) transparent ceramics. Upon the 467 nm excitation, the energy transfer process was dominated by the cooperative downconversion from the 5d{sub 1} state of one Ce{sup 3+} ion to the {sup 2}F{sub 5/2} state of two Yb{sup 3+} ions. The influence of the Ce{sup 4+}-Yb{sup 2+} charge transfer state (CTS) should not contribute much to the energy transfer process for the large energy gap between Ce{sup 3+}:5d{sub 1} and the CTS. The calculated quantum yield of Yb{sup 3+} for the x=0.25 sample without concentration quenching was 175.4%.

36 MATERIALS SCIENCE↗

Experimental Verification of Solidification Stress Theory

A research program is being conducted to develop a crack-free ceramic waste form (CWF) to be used for long term encasement of fission products and actinides resulting from processing spent nuclear fuel. Cracking usually occurs in the cooldown phase of the glass or ceramic formations. A crack-free formation should have more resistance to leaching than one with many cracks. In the research leading up to producing a CWF, a model was developed that proposes a permanent stress develops when the melt solidifies and that this stress can cause failure as the CWF nears room temperature. This paper reports on how the formation, CWF2, confirms the existence of this stress. The solidification stress is in addition to and of opposite sign of the thermal stress. Its derivation is reported on in Ref. 1. Cracking of the CWF would occur at low temperatures if solidification stress exists but at high temperatures if it doesn’t. If solidification stress occurs, then the cooldown rate during solidification should be reduced. If not, it should be reduced when the thermal stresses are highest. Recording cracking sounds confirm the existence of this solidification stress since cracking occurred during the low temperature phase of the cooldown. As a side purpose of this paper, a cooldown rate is proposed that should eliminate cracking in the next experiment, CWF3. CWF2 is a prototype vertical ceramic waste cylinder formed over a period of 10 days by heating a mixture of 75% zeolite, 25% glass frit in an argon atmosphere furnace through melting to 925 C and then cooling through solidification to room temperature. It is approximately 1 m high, 0.5 m in diameter, weighs about 400 kg, and is formed in a stainless steel can 0.5 cm thick. This cylinder developed many cracks on cooldown. At least 15 loud cracks were recorded over a period of 4 days at the end of cooldown when the temperatures were below 400 C. The CWF2 surface and centerline temperatures at mid height were measured which allowed the stress to be calculated. The timing of the cracks was compared to the time the calculated total stress exceeded the tensile stress limit and verified that the cause of the cracking was solidification stress and not thermal stress. Since the CWF is encased in a can in a furnace, the cracks cannot be easily observed but can be detected with sound measurements. Similarly, the stress cannot be measured but only estimated with analysis. Destructive examination of the CWF after cooldown was used to determine the pattern of the cracking which appeared to be initiated mainly in the inner region which is evidence the cracking is due to solidification stress.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Processing of Rigidized Rei-mullite Insulative Composites

Systematic development and evaluation of ceramic fiber Mullite are summarized: (1) Major reductions in thermal protection system weight have been achieved by reducing the density and thermal conductivity of the insulation by 20 and 25 percent; (2) already adequate structural margins-of-safety have been greatly enhanced by increasing the tensile strength and strain-to-failure capabilities of the insulation by factors of 3 and 2; (3) cost effectiveness has been increased through the achievement of a high degree of uniformity and reproducibility of properties and through process simplification and binder modifications; and (4) maximization of multimission capability at surface temperatures of 1644 K has been achieved through firing cycle adjustments and the development of a material with high dimensional stability.

Gebhardt, J. J.↗

Test Structures Applied to the Rapid Prototyping of Sensors

Recently, test structures were used to aid in the rapid development of a gas sensor and pressure sensor. These sensors were fabricated using co-fired ceramic technology and a multiproject approach. This talk will describe results obtained from a ceramic substrate which contained 36 chips with six variants including the sensors, process control monitors, and an interconnect chip. As far as the authors know, this is the first implementation of multi-projects in co-fired ceramic substrate. The gas sensor is being developed for the Space Shuttle and the pressure gage is being developed as a Martian barometer.

sensors ceramic substrate prototyping↗

Glass Ceramic Waste Forms for Combined CS+LN+TM Fission Products Waste Streams

In this study, glass ceramics were explored as an alternative waste form for glass, the current baseline, to be used for immobilizing alkaline/alkaline earth + lanthanide (CS+LN) or CS+LN+transition metal (TM) fission-product waste streams generated by a uranium extraction (UREX+) aqueous separations type process. Results from past work on a glass waste form for the combined CS+LN waste streams showed that as waste loading increased, large fractions of crystalline phases precipitated upon slow cooling. The crystalline phases had no noticeable impact on the waste form performance by the 7-day product consistency test (PCT). These results point towards the development of a glass ceramic waste form for treating CS+LN or CS+LN+TM combined waste streams. Three main benefits for exploring glass ceramics are: • Glass ceramics offer increased solubility of troublesome components in crystalline phases as compared to glass, leading to increased waste loading; • The crystalline network formed in the glass ceramic results in higher heat tolerance than glass; and • These glass ceramics are designed to be processed by the same melter technology as the current baseline glass waste form. It will only require adding controlled canister cooling for crystallization into a glass ceramic waste form. Highly annealed waste form (essentially crack free) with up to 50X lower surface area than a typical High-Level Waste (HLW) glass canister. Lower surface area translates directly into increased durability. This was the first full year of exploring glass ceramics for the Option 1 and 2 combined waste stream options. This work has shown that dramatic increases in waste loading are achievable by designing a glass ceramic waste form as an alternative to glass. Table S1 shows the upper limits for heat, waste loading (based on solubility), and the decay time needed before treatment can occur for glass and glass ceramic waste forms. The improvements are significant for both combined waste stream options in terms of waste loading and/or decay time required before treatment. For Option 1, glass ceramics show an increase in waste loading of 15 mass % and reduction in decay time of 24 years. Decay times of ≈50 years or longer are close to the expected age of the fuel that will be reprocessed when the modified open or closed fuel cycle is expected to be put into action. Option 2 shows a 2x to 2.5x increase in waste loading with decay times of only 45 years. Note that for Option 2 glass, the required decay time before treatment is only 35 years because of the waste loading limits related to the solubility of MoO 3 in glass. If glass was evaluated for similar waste loadings as those achieved in Option 2 glass ceramics, the decay time would be significantly longer than 45 years. These glass ceramics are not optimized, but already they show the potential to dramatically reduce the amount of waste generated while still utilizing the proven processing technology used for glass production.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Colossal dielectric constant and relaxation behaviors in Pr:SrTiO{sub 3} ceramics

Sr{sub 1-x}Pr{sub x}TiO{sub 3} ceramics (0.00{<=}x{<=}0.03) were prepared by a traditional solid-state reaction method. Two relaxation processes (marked as A and B) of the Sr{sub 0.09}Pr{sub 0.01}TiO{sub 3} ceramics were investigated by analyzing the E{sub a} values obtained from the Arrhenius law. Colossal dielectric constant (CDC) was first obtained in Sr{sub 0.09}Pr{sub 0.01}TiO{sub 3} ceramics, whose permittivity was up to 3000 (1 kHz, room temperature), greater than that of pure SrTiO{sub 3} ceramics and samples with more Pr addition (x=0.02 and 0.03). This CDC behavior was related to the internal barrier layer capacitance mechanism.

36 MATERIALS SCIENCE↗

Investigation of processing advanced waste forms in Cold Crucible Induction Melter systems

The Cold Crucible Induction Melter (CCIM) technology has been identified in several independent reviews and studies as a potential alternative or supplemental vitrification technology for specific U.S. Department of Energy (DOE) high level radioactive waste (HLW) streams. These inventories have unique chemistries, such as high alumina, high iron, high chromium, etc., that are not amenable to efficient immobilization in conventional borosilicate glass (BSG) matrices. Advanced waste forms, such as iron phosphate glass (FePG), high crystalline BSG (HC-BSG), and alumino-silicate glass-ceramic (GC) have been shown to provide significantly improved immobilization matrices for these challenging waste streams, including dramatically improved waste loadings; however, they are difficult to efficiently process in the baseline joule-heated ceramic melters (JHCMs). The CCIM technology can effectively process these advanced waste forms at the desired high waste loadings. This paper describes the most recent collaborative activities between the DOE Office of Environmental Management (DOE EM) and various Russian institutions in modeling, development and testing of advanced waste forms in CCIMs, including FePG and HC-BSG formulations. Additionally, past interactions with other international partners, including France and Korea, are described. Finally, recent enhancements to CCIM processing related to modeling, draining techniques and automated control, which were collaboratively developed, will be discussed. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

High temperature deformability of ductile flash-sintered ceramics via in-situ compression

Flash sintering has attracted significant attention as its remarkably rapid densification process at low sintering furnace temperature leads to the retention of fine grains and enhanced dielectric properties. However, high-temperature mechanical behaviors of flash-sintered ceramics remain poorly understood. Here, we present high-temperature (up to 600 °C) in situ compression studies on flash-sintered yttria-stabilized zirconia (YSZ). Below 400 °C, the YSZ exhibits high ultimate compressive strength exceeding 3.5 GPa and high inelastic strain (~8%) due primarily to phase transformation toughening. At higher temperatures, crack nucleation and propagation are significantly retarded, and prominent plasticity arises mainly from dislocation activity. The high dislocation density induced in flash-sintered ceramics may have general implications for improving the plasticity of sintered ceramic materials.

36 MATERIALS SCIENCE↗

How We Used NASA Lunar Set in Planetary Material Science Analog Studies on Lunar Basalts and Breccias with Industrial Materials of Steels and Ceramics

Analog studies play important role in space materials education. Various aspects of analogies are used in our courses. In this year two main rock types of NASA Lunar Set were used in analog studies in respect of processes and textures with selected industrial material samples. For breccias and basalts on the lunar side, ceramics and steels were found as analogs on the industrial side. Their processing steps were identified on the basis of their textures both in lunar and in industrial groups of materials.

Berczi, S.↗

Test Structures for Rapid Prototyping of Gas and Pressure Sensors

A multi-project ceramic substrate was used in developing a gas sensor and pressure sensor. The ceramic substrate cantained 36 chips with six variants including sensors, process control monitors, and an interconnect ship. Tha gas sensor is being developed as an air quality monitor and the pressure gauge as a barometer.

ceramics ceramic substrate gas sensor pressure sen↗

Low temperature dielectric and impedance studies on magnetoelectric Pb(Fe{sub 0.5}Nb{sub 0.5})O{sub 3} ceramic

The structural, microstructural, low temperature dielectric and impedance properties of Pb(Fe{sub 0.5}Nb{sub 0.5})O{sub 3} (PFN) ceramic prepared by single step solid-state reaction method have been investigated. Processing parameters such as calcination, sintering temperature and sintering durations were optimized to get better dielectric properties. It was found that the above ceramics sintered at 1050 °C for 4 hr exhibited single phase, maximum density and uniform microstructure. X-ray diffraction (XRD) and neutron diffraction (ND) reveals that the system exhibit single phase without any kind of secondary phases at room temperature (RT) with monoclinic crystal structure (Cm). Surface morphology of the compounds was studied by Scanning electron microscope (SEM). Impedance spectroscopy is used to study the electrical behaviour of PFN in the frequency range from 100Hz to 1MHz and in the temperature range from 120 to 293 K. The frequency-dependent electrical data are analyzed by impedance formalisms. The complex impedance shows the relaxation (conduction) mechanism in the sample.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Probabilistic Modeling of Ceramic Matrix Composite Strength

Uncertainties associated with the primitive random variables such as manufacturing process (processing temperature, fiber volume ratio, void volume ratio), constituent properties (fiber, matrix and interface), and geometric parameters (ply thickness, interphase thickness) have been simulated to quantify the scatter in the first matrix cracking strength (FMCS) and the ultimate tensile strength of SCS-6/RBSN (SiC fiber (SCS-6) reinforced reaction-bonded silicon nitride composite) ceramic matrix composite laminate at room temperature. Cumulative probability distribution function for the FMCS and ultimate tensile strength at room temperature (RT) of (0)(sub 8), (0(sub 2)/90(sub 2), and (+/-45(sub 2))(sub S) laminates have been simulated and the sensitivity of primitive variables to the respective strengths have been quantified. Computationally predicted scatter of the strengths for a uniaxial laminate have been compared with those from limited experimental data. Also the experimental procedure used in the tests has been described briefly. Results show a very good agreement between the computational simulation and the experimental data. Dominating failure modes in (0)(sub 8), (0/90)(sub s) and (+/-45)(sub S) laminates have been identified. Results indicate that the first matrix cracking strength for the (0)(sub S), and (0/90)(sub S) laminates is sensitive to the thermal properties, modulus and strengths of both the fiber and matrix whereas the ultimate tensile strength is sensitive to the fiber strength and the fiber volume ratio. In the case of a (+/-45)(sub S), laminate, both the FMCS and the ultimate tensile strengths have a small scatter range and are sensitive to the fiber tensile strength as well as the fiber volume ratio.

Shan, Ashwin R.↗

Effect of TiO{sub 2} Addition on Grain Growth, Anodic Bubble Evolution and Anodic Overvoltage of NiFe{sub 2}O{sub 4}-Based Composite Inert Anodes

A two-step powder compaction and sintering process was employed to fabricate TiO{sub 2}-doped NiFe{sub 2}O{sub 4} ceramic-based inert anodes. Grain growth during isothermal sintering was analyzed using Brook grain growth model. The bubble behavior of NiFe{sub 2}O{sub 4} ceramic-based inert anodes was investigated in a two-compartment see-through quartz cell for aluminum electrolysis process. Anodic overvoltage and potential decay curves of the inert anodes were measured by using the steady state and current interruption technique. The results showed that the kinetic index of grain growth decreased with an increase in temperature. The average activation energy of grain growth for 1.0 wt.% TiO{sub 2}-doped NiFe{sub 2}O{sub 4} ceramic samples with a sintering temperature range from 1373 to 1673 K dropped from 675.30 to 183.47 kJ/mol. The diameter size of bubbles before releasing from the bottom surface of the anodes was reduced with increasing the current density, and the larger average releasing bubble size for carbon anode at the same current density could be obtained, which was compared to the NiFe{sub 2}O{sub 4} inert anodes. Besides, the cell voltage of carbon anodes fluctuated much more violently under the same experimental conditions. After adding small amount of TiO{sub 2}, a minor reduction in anodic overvoltage of NiFe{sub 2}O{sub 4}-based anodes can be observed.

36 MATERIALS SCIENCE↗

Cesium incorporation in hollandite-rich multiphasic ceramic waste forms

Hollandite-rich multiphase waste form compositions processed by melt-solidification and spark plasma sintering (SPS) were characterized, compared, and validated for nuclear waste incorporation. Phase identification by x-ray diffraction (XRD) and electron back-scattered diffraction (EBSD) confirmed hollandite as the major phase present in these samples along with perovskite, pyrochlore and zirconolite. Distribution of selected elements observed by wavelength dispersive spectroscopy (WDS) maps indicated that Cs formed a secondary phase during SPS processing, which was considered undesirable. On the other hand, Cs partitioned into the hollandite phase in melt-processed samples. Further analysis of hollandite structure in melt-processed composition by selected area electron diffraction (SAED) revealed ordered arrangement of tunnel ions (Ba/Cs) and vacancies, suggesting efficient Cs incorporation into the lattice.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Lightweight Chambers for Thrust Assemblies

The Marshall Space Flight Center (MSFC) of the National Aeronautics and Space Administration (NASA) has successfully applied new materials and fabrication techniques to create actively cooled thrust chambers that operate 200-400 degrees hotter and weigh 50% lighter than conventional designs. In some vehicles, thrust assemblies account for as much as 20% of the engine weight. So, reducing the weight of these components and increasing their operating range will benefit many engines and vehicle designs, including Reusable Launch Vehicle (RLV) concepts. Obviously, copper and steel alloys have been used successfully for many years in the chamber components of thrust assemblies. Yet, by replacing the steel alloys with Polymer Matrix Composite (PMC) and/or Metal Matrix Composite (MMC) materials, design weights can be drastically reduced. In addition, replacing the traditional copper alloys with a Ceramic Matrix Composite (CMC) or an advanced copper alloy (Cu-8Cr-4Nb, also known as GRCop-84) significantly increases allowable operating temperatures. Several small MMC and PMC demonstration chambers have recently been fabricated with promising results. Each of these designs included GRCop-84 for the cooled chamber liner. These units successfully verified that designs over 50% lighter are feasible. New fabrication processes, including advanced casting technology and a low cost vacuum plasma spray (VPS) process, were also demonstrated with these units. Hot-fire testing at MSFC is currently being conducted on the chambers to verify increased operating temperatures available with the GRCop-84 liner. Unique CMC chamber liners were also successfully fabricated and prepared for hot-fire testing. Yet, early results indicate these CMC liners need significantly more development in order to use them in required chamber designs. Based on the successful efforts with the MMC and PMC concepts, two full size "lightweight" chambers are currently being designed and fabricated for hot-fire testing at MSFC in 2001. These "full size" chambers will be similar in size to those used on the X33 engine (RS2200). One will be fabricated with a MMC structural jacket, while the other uses a PMC jacket. Each will be designed for thrust levels of 15,000 pounds in an oxygen/hydrogen environment with liquid hydrogen coolant. Both chambers will use GRCop-84 for its channel wall liner. Each unit is expected to be at least 60% lighter than a conventional design with traditional materials. Hot-fire testing on the full size units in late 2001 will directly compare performance results between a conventional chamber design and these "lightweight" alternatives. The technology developed and demonstrated by this effort will not only benefit next generation RLV programs, but it can be applied to other existing and future engine programs, as well. Efforts were sponsored by the Advanced Space Transportation Program for RLV Focused Technologies. The task team was led by MSFC with additional members from NASA-Glenn Research Center and the Rocketdyne Division of The Boeing Company. Specific materials development and fabrication processes were provided by Aerojet, Lockheed Martin Astronautics, Composite Optics, Inc., Hyper-Therm, Ceramic Composites, Inc., MSE Technology Applications, and Plasma Processes, Inc.

Elam, Sandra K.↗

Initial Examination of Low Velocity Sphere Impact of Glass Ceramics

This report summarizes US Army TARDEC sponsored work at Oak Ridge National Laboratory (ORNL) involving low velocity (< 30 m/s or < 65 mph) sphere impact testing of two materials from the lithium aluminosilicate family reinforced with different amounts of ceramic particulate, i.e., glass-ceramic materials, SCHOTT Resistan™-G1 and SCHOTT Resistan™-L. Both materials are provided by SCHOTT Glass (Duryea, PA). This work is a follow-up to similar sphere impact studies completed by the authors on PPG's Starphire® soda-lime silicate glass and SCHOTT BOROFLOAT® borosilicate glass. A gas gun or a sphere-drop test setup was used to produce controlled velocity delivery of silicon nitride (Si 3 N 4 ) spheres against the glass ceramic tile targets. Minimum impact velocities to initiate fracture in the glass-ceramics were measured and interpreted in context to the kinetic energy of impact and the elastic property mismatch between sphere and target material. Quasistatic spherical indentation was also performed on both glass ceramics and their contact damage responses were compared to those of soda-lime silicate and borosilicate glasses. Lastly, variability of contact damage response was assessed by performing spherical indentation testing across the area of an entire glass ceramic tile. The primary observations from this low velocity (< 30 m/s or < 65 mph) testing were: (1) Resistan™-L glass ceramic required the highest velocity of sphere impact for damage to initiate. Starphire® soda-lime silicate glass was second best, then Resistan™-G1 glass ceramic, and then BOROFLOAT® borosilicate glass. (2) Glass-ceramic Resistan™-L also required the largest force to initiate ring crack from quasi-static indentation. That ranking was followed, in descending order, by Starphire® soda-lime silicate glass, Resistan™-G1 glass ceramic, and BOROFLOAT® borosilicate glass. (3) Spheres with a lower elastic modulus require less force to initiate fracture in Resistan™-G1 from quasi-static spherical indentation. This indicates that friction is affecting ring crack initiation in Resistan™-G1. Friction also affected ring crack initiation in Starphire® soda-lime silicate and BOROFLOAT® borosilicate glasses. Among these three materials, friction was the most pronounced (largest slope in the RCIF-elastic modulus graph) in the Starphire® and least pronounced in the BOROFLOAT®. The reason for this is not understood, but differences in deformation behavior under high contact stresses could be a cause or contributor to this. (4) The force necessary to initiate contact-induced fracture is higher under dynamic conditions than it is under quasi-static conditions in Resistan™-L and Resistan™-G1 glass ceramics. This is a trend observed too in Starphire® and BOROFLOAT®. (5) There is a subtle indication there was intra-tile differences in spherical indentation-induced ring crack initiation forces. This is not a material property nor is it exclusive to glass-ceramic Resistan™-G1 glass ceramic, rather, it is a statistical mechanical response to an accumulated history of processing and handling of that specific tile.

36 MATERIALS SCIENCE↗

Microstructure and electrical properties in W/Nb co-doped Aurivillius phase Bi{sub 4}Ti{sub 3}O{sub 12} piezoelectric ceramics

Highlights: • W/Nb codoped BIT ceramics were prepared by the mixed oxides route. • High nd{sup 0} electronic configuration of W/Nb reduces the lattice distortion and T{sub C}. • Oxygen vacancy is responsible for dielectric relaxation and DC conduction process. • W/Nb additives significantly enhanced the piezoelectric coefficient d{sub 33} value. • BWNb-10 ceramics possessed large remnant polarization and a wide sintering window. - Abstract: Aurivillius-type Bi{sub 4}Ti{sub 3-x}W{sub x/2}Nb{sub x/2}O{sub 12} ceramics were prepared by a conventional solid-state sintering method. The XRD patterns demonstrated that all compositions were a single three layered crystalline structure, involving a reduction of lattice distortion with an increase in W/Nb doping level. The electrical properties including dielectric, electrical conduction and piezoelectric properties were tailored by W/Nb additives. The Curie-temperature decreased, whereas the electrical resistivity drastically increased with introduction of W/Nb donor dopants. As a result, a high electric field can be applied during the poling process. The Bi{sub 4}Ti{sub 2.9}W{sub 0.05}Nb{sub 0.05}O{sub 12} ceramics exhibited optimum piezoelectric coefficient (d{sub 33} ∼22.8 pC/N), large remnant polarization (2P{sub r} ∼26.8 μC/cm{sup 2} @ 200 °C) together with a high Curie temperature (T{sub C} ∼635 °C). Furthermore, this composition possessed a wide sintering window with outstanding piezoelectric properties. These parameters indicate that Bi{sub 4}Ti{sub 2.9}W{sub 0.05}Nb{sub 0.05}O{sub 12}-based ceramic is a promising candidate for high temperature piezoelectric applications.

36 MATERIALS SCIENCE↗