Search NASA⌕ Search

SEARCH · Search NASA

Results for “compression ignition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Hydrodynamic instability growth and mix experiments at the National Ignition Facility

Hydrodynamic instability growth and its effects on implosion performance were studied at the National Ignition Facility [G. H. Miller, E. I. Moses, and C. R. Wuest, Opt. Eng. 443, 2841 (2004)]. Implosion performance and mix have been measured at peak compression using plastic shells filled with tritium gas and containing embedded localized carbon-deuterium diagnostic layers in various locations in the ablator. Neutron yield and ion temperature of the deuterium-tritium fusion reactions were used as a measure of shell-gas mix, while neutron yield of the tritium-tritium fusion reaction was used as a measure of implosion performance. The results have indicated that the low-mode hydrodynamic instabilities due to surface roughness were the primary culprits for yield degradation, with atomic ablator-gas mix playing a secondary role. In addition, spherical shells with pre-imposed 2D modulations were used to measure instability growth in the acceleration phase of the implosions. The capsules were imploded using ignition-relevant laser pulses, and ablation-front modulation growth was measured using x-ray radiography for a shell convergence ratio of ∼2. The measured growth was in good agreement with that predicted, thus validating simulations for the fastest growing modulations with mode numbers up to 90 in the acceleration phase. Future experiments will be focused on measurements at higher convergence, higher-mode number modulations, and growth occurring during the deceleration phase.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Influence of Compression Ratio on High Load Performance and Knock Behavior for Gasoline Port-Fuel Injection, Natural Gas Direct Injection and Blended Operation in a Spark Ignition Engine

Natural Gas (NG) is an alternative fuel which has attracted a lot of attention recently, in particular in the US due to shale gas availability. The higher hydrogen-to-carbon (H/C) ratio, compared to gasoline, allows for decreasing carbon dioxide emissions throughout the entire engine map. Furthermore, the high knock resistance of NG allows increasing the efficiency at high engine loads compared to fuels with lower knock resistance. NG direct injection (DI) allows for fuel to be added after intake valve closing (IVC) resulting in an increase in power density compared to an injection before IVC. Steady-state engine tests were performed on a single-cylinder research engine equipped with gasoline (E10) port-fuel injection (PFI) and NG DI to allow for in-cylinder blending of both fuels. Knock investigations were performed at two discrete compression ratios (CR), 10.5 and 12.5. Operating conditions span mid-load, wide-open-throttle and boosted conditions, depending on the knock response of the fuel blend. Blended operation was performed using E10 gasoline and NG. An additional gasoline type fuel (E85) with higher knock resistance than E10 was used as a high-octane reference fuel, since the octane rating of E10-NG fuel blends is unknown. Spark timing was varied at different loads under stoichiometric conditions in order to study the knock response as well as the effects on performance and efficiency. As anticipated, results suggest that the knock resistance can be increased significantly by increasing the NG amount. Comparing the engine operation with the least knock resistant fuel, E10 PFI, and the fuel blend with the highest knock resistance, 75% NG DI, shows an increase in indicated mean effective pressure of about 9 bar at CR 12.5. The usage of reference fuels with known knock characteristics allowed an assessment of knock characteristic of intermediate E10-NG blend levels. Mathematical correlations were developed allowing characterizing the occurrence of knocking combustion by using the Livengood-Wu knock integral. For most of the fueling strategies and operating conditions, the mathematical correlations show good agreement when compared to experimental data.

combustion↗

SHOCK INITIATION EXPERIMENTS PLUS IGNITION AND GROWTH MODELING OF DAMAGED LX-04 CHARGES

Shock initiation experiments were performed on mechanically and thermally damaged LX-04 (85% HMX and 15% Viton by weight) to obtain in-situ manganin pressure gauge data and run distances to detonation at various shock pressures. The LX-04 charges were damaged mechanically by applying a compressive load of 600 psi for 20,000 cycles, thus creating many small narrow cracks, or by cutting wedge shaped parts that were then loosely reassembled, thus creating a few large cracks. The thermal damaged LX-04 charges were heated to 190 C for a long enough time for the beta to delta phase transition to occur and then cooled to ambient temperature. Mechanically damaged LX-04 exhibited only slightly increased shock sensitivity, while the thermally damaged LX-04 was much more shock sensitive. The pristine LX-04 Ignition and Growth model, modified only by igniting a larger amount of explosive during shock compression based on the damaged charge density, accurately calculated the increased shock sensitivity of the three damaged charges.

36 MATERIALS SCIENCE↗

End-gas autoignition fraction and flame propagation rate in laser-ignited primary reference fuel mixtures at elevated temperature and pressure

Knock in spark-ignited (SI) engines is initiated by autoignition of the unburned gasses upstream of spark-ignited, propagating, turbulent premixed flames. Knock propensity of fuel/air mixtures is typically quantified using research octane number (RON), motor octane number (MON), or methane number (MN; for gaseous fuels), which are measured using single-cylinder, variable compression ratio engines. In this study, knock propensity of SI fuels was quantified via observations of end-gas autoignition (EGAI) in unburned gasses upstream of laser-ignited, premixed flames at elevated pressures and temperatures in a rapid compression machine. Stoichiometric primary reference fuel (PRF; n-heptane/isooctane) blends of varying reactivity (50 ≤ PRF ≤ 100) were ignited using an Nd:YAG laser over a range of temperatures and pressures, all in excess of 545 K and 16.1 bar. Laser ignition produced outwardly-propagating premixed flames. High-speed pressure measurements and schlieren images indicated the presence of EGAI. The fraction of the total heat release attributed to EGAI (i.e., EGAI fraction) varied with fuel reactivity (i.e., octane number) and the time-integrated temperature of the end-gas prior to ignition. Flame propagation rates, which were measured using schlieren images, were only weakly correlated with octane number but were affected by turbulence caused by variation in piston timing. Under conditions of low turbulence, measured flame propagation rates approached one-dimensional premixed laminar flame speed computations performed at the same conditions. Experiments were simulated with a three-dimensional CONVERGE™ model using reduced chemical kinetics (121 species, 538 reactions). The simulations accurately captured the measured flame propagation rates, as well as the variation in EGAI fraction with fuel reactivity and time-integrated end-gas temperature. The simulations also revealed low-temperature heat release as well as formaldehyde and hydrogen peroxide formation in the end-gas upstream of the propagating flame, which increased the temperature and degree of chain branching in the end-gas, ultimately leading to EGAI.

42 ENGINEERING↗

Thermonuclear targets for direct-drive ignition by a megajoule laser pulse

Central ignition of a thin two-layer-shell fusion target that is directly driven by a 2-MJ profiled pulse of Nd laser second-harmonic radiation has been studied. The parameters of the target were selected so as to provide effective acceleration of the shell toward the center, which was sufficient for the onset of ignition under conditions of increased hydrodynamic stability of the ablator acceleration and compression. The aspect ratio of the inner deuterium-tritium layer of the shell does not exceed 15, provided that a major part (above 75%) of the outer layer (plastic ablator) is evaporated by the instant of maximum compression. The investigation is based on two series of numerical calculations that were performed using one-dimensional (1D) hydrodynamic codes. The first 1D code was used to calculate the absorption of the profiled laser-radiation pulse (including calculation of the total absorption coefficient with allowance for the inverse bremsstrahlung and resonance mechanisms) and the spatial distribution of target heating for a real geometry of irradiation using 192 laser beams in a scheme of focusing with a cubo-octahedral symmetry. The second 1D code was used for simulating the total cycle of target evolution under the action of absorbed laser radiation and for determining the thermonuclear gain that was achieved with a given target.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Insights into Engine Knock: Comparisons of Knock Metrics across Ranges of Intake Temperature and Pressure in the CFR Engine

Of late there has been a resurgence in studies investigating parameters that quantify combustion knock in both standardized platforms and modern spark-ignition engines. However, it is still unclear how metrics such as knock (octane) rating, knock onset, and knock intensity are related and how fuels behave according to these metrics across a range of conditions. As part of an ongoing study, the air supply system of a standard Cooperative Fuel Research (CFR) F1/F2 engine was modified to allow mild levels of intake air boosting while staying true to its intended purpose of being the standard device for American Society for Testing and Materials (ASTM)-specified knock rating or octane number tests. For instance, the carburation system and intake air heating manifold are not altered, but the engine was equipped with cylinder pressure transducers to enable both logging of the standard knockmeter readout and state-of-the-art indicated data. For this study, the engine was operated using primary reference fuel 90 (PRF90) at 600 rpm, first following the procedures of the ASTM D2699 research octane number test protocol in order to define the geometric compression ratio set point for standard knock number. Thereafter, compression ratio sweeps were conducted at intake temperatures ranging from 30 to 150°C and intake air boost extending from 0 to 0.3 bar above ambient. The resulting operating map provided a broad envelope of compressed in-cylinder conditions relevant to modern spark-ignition engines. Detailed analysis of the indicated data highlighted a poor correlation between established knock intensity metrics and the knockmeter reading, which is used to characterize a fuel’s octane number. It was further found that the auto-ignition characteristics of PRF90 could be perturbed by means of intake air boosting and heating without being captured by the knockmeter reading.

Rockstroh, Toby↗

Long-term compression effects on elastomeric O-ring behavior

This paper discusses the results of testing performed on elastomeric seal materials that had been under compression for extended periods of time. Elastomeric seals used in the Space Shuttle redesigned solid rocket motors can experience compression times of up to six months. These seals must be capable of sealing internal motor pressure upon ignition. The tests described herein were performed in order to verify that the seals, which had experienced long-term compression could seal throughout motor operation. Testing was divided into two phases: (1) dynamic high pressure testing, and (2) resiliency testing. Dynamic testing was performed using specialized test fixtures that allowed simulation of the field joint movements during initial motor operation along with high pressure gas. Resiliency testing was performed using specialized test fixtures that also simulated field joint movements and also had the ability to measure the sealing force of the O-ring. Results from all testing indicated that the current elastomeric seals used in the redesigned solid rocket motors will seal during motor operations in the currently defined launch environments.

Clinton, R. G.↗

The five line-of-sight neutron time-of-flight (nToF) suite on the National Ignition Facility (NIF)

Measurement of the neutron spectrum from inertial confinement fusion implosions is one of the primary diagnostics of implosion performance. Analysis of the spectrum gives access to quantities such as neutron yield, hot-spot velocity, apparent ion temperature, and compressed fuel ρr through measurement of the down-scatter ratio. On the National Ignition Facility, the neutron time-of-flight suite has been upgraded to include five independent, collimated lines of sight, each comprising a high dynamic range bibenzyl/diphenylacetylene-stilbene scintillator [R. Hatarik et al., Plasma Fusion Res. 9, 4404104 (2014)] and high-speed fused silica Cherenkov detectors [A. S. Moore et al., Rev. Sci. Instrum. 89, 10I120 (2018)].

Moore, A. S. (ORCID:0000000221258882)↗

MAGO-IX Experiment

The results of the last (in the thermonuclear program “Magnetic compression”) MAGO-IX experiment with a plasma chamber including a third compartment designed to compress plasma with a converging liner are presented. An X-ray pulse consisting of an intense peak of 1-μs duration, followed by a low-intensity tail with a duration of more than 10 μs, was recorded. In the MAGO-IX experiment, the neutrons were generated mainly in the third compartment. A neutron yield of 2 × 10{sup 12} was obtained. The results demonstrate that the expected compression of preheated plasma in chambers similar to MAGO-IX is promising for achieving thermonuclear ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Time-Resolved Fuel Density Profiles of the Stagnation Phase of Indirect-Drive Inertial Confinement Implosions

The implosion efficiency in inertial confinement fusion depends on the degree of stagnated fuel compression, density uniformity, sphericity, and minimum residual kinetic energy achieved. Compton scattering-mediated 50–200 keV x-ray radiographs of indirect-drive cryogenic implosions at the National Ignition Facility capture the dynamic evolution of the fuel as it goes through peak compression, revealing low-mode 3D nonuniformities and thicker fuel with lower peak density than simulated. By differencing two radiographs taken at different times during the same implosion, we also measure the residual kinetic energy not transferred to the hot spot and quantify its impact on the implosion performance.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A Rapid Compression Machine Study of 2-Phenylethanol Autoignition at Low-To-Intermediate Temperatures

To meet the increasing anti-knocking quality demand of boosted spark-ignition engines, fuel additives are considered an effective approach to tailor fuel properties for satisfying the performance requirements. Thus, screening/developing bio-derived fuel additives that are best-suited for advanced spark-ignition engines has become a significant task. 2-Phenylethanol (2-PE) is an attractive candidate that features high research octane number, high octane sensitivity, low vapor pressure, and high energy density. Recognizing that the low temperature autoignition chemistry of 2-PE is not well understood and the need for fundamental experimental data at engine-relevant conditions, rapid compression machine (RCM) experiments are therefore conducted herein to measure ignition delay times (IDTs) of 2-PE in air over a wide range of conditions to fill this fundamental void. These newly acquired IDT data at low-to-intermediated temperatures, equivalence ratios of 0.35–1.5, and compressed pressures of 10–40 bar are then used to validate the 2-PE model developed by Shankar et al. (2017). It is found that this literature model greatly overpredicts the current RCM data. The comparison of experimental and simulated results also provides insights into 2-PE autoignition behaviors at varying conditions. Further chemical kinetic analyses demonstrate that the absence of the O2-addition pathway of β-R. radical in the 2-PE model of Shankar et al. (2017) could account for the model discrepancies observed at low-to-intermediated temperatures.

Fang, Ruozhou (ORCID:0000000348315100)↗

A Brief Study on Toxic Combustion Products of the Polymers Used in High-Pressure Oxygen Systems

One likely cause of polymer ignition in a high-pressure oxygen system is the adiabatic-compression heating of polymers caused by pneumatic impact. Oxidative pyrolysis or combustion of polymers in a high-pressure oxygen system could generate toxic gases. This paper investigates the feasibility of using the NASA pneumatic-impact system to conduct adiabatic-compression combustion tests and determines the toxic combustion products produced from the burning of five selected polymers. Five polymers commonly used in high-pressure oxygen systems, Zytel(Registered TradeMark) 42 (Nylon 6/6), Buna N (nitrile rubber), Witon(Registered TradeMark) A (copolymer of vinylidene fluoride and hexafluoropropylene), Neoflon(Registered TradeMark) (polychlorotrifluoroethylene), and Teflon(Registered TradeMark) (polytetrafluoroethylene), were tested in the NASA pneumatic-impact test system at 17.2-MPa oxygen pressure. The polymers were ignited and burned; combustion products were collected in a stainless-steel sample bottle and analyzed using various methods. The results show that the NASA pneumatic-impact system is an appropriate test system to conduct adiabatic-compression combustion tests and to collect combustion products for further chemical analysis. The composition of the combustion product gas generated from burning the five selected polymers are presented and discussed.

Hshieh, Fu-Yu↗

The interaction of quasi-monoenergetic protons with pre-compressed inertial fusion fuels

The interaction of a quasi-monoenergetic proton beam with a pre-compressed plasma is studied in the context of inertial fusion fast ignition (FI). Based on fundamental principles, a kinetic model is developed by considering hard collisions, nuclear scattering, and the contribution due to collective processes. The penetration depth, longitudinal straggling, and the transverse blooming are evaluated by solving the Boltzmann transport equation using the multiple scattering theory. The stopping power, transport scattering cross sections, and convenient expressions for the angular moments of the proton distribution function have been used in modeling the collisional proton transport in a three-dimensional (3D) Monte Carlo code. The transport of a proton beam with a quasi-monoenergetic energy =10 MeV is studied for pre-compressed deuterium-tritium plasma with an average density of {rho}=400 g cm{sup -3} and temperatures T=1 keV, 5 keV, and 10 keV. The net effects of multiple scattering are to reduce the penetration from 1.028 to 0.828 g cm{sup -2} with range straggling {rho}{Sigma}{sub R}=0.044 g cm{sup -2} and beam blooming {rho}{Sigma}{sub B}=0.272 g cm{sup -2}, for 10 MeV protons in a {rho}=400 g cm{sup -3} plasma at T = 5 keV. This model can be used for quantitatively assessing ignition requirements for proton fast ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fracture Effects on Explosive Response (FEER); FY2018 Report

It is known that the violence of explosive response is affected by inertial and mechanical confinement. In a mechanical insult, the impact location creates a contact pressure that can act as confinement surrounding the ignition location, as has been observed in the Skid Test experiment. Under certain conditions — the details of which have not been well characterized — the ignition can produce cracking in the explosive, down which flames are observed to propagate. Cracks serve to simultaneously provide additional surface area for accelerating the reaction, as well as vent paths for quenching the reaction. These are competing behaviors, and the factors which govern the outcome are poorly described. A new experiment was devised to examine the effect of a controlled pre-load pressure on the explosive response. Sixteen experiments were performed on 1-inch thick discs of PBX 9501, with diameters of 1 in ch, 4.25 in ch, and 5 in ch. The explosive was compressed to a known pre-load between two clear windows and ignited at the center of the bottom surface with a focused laser impinging on a graphite inclusion. The ensuing reaction was imaged through the windows used to compress the sample, and from the side. A speckle pattern was applied to some samples for performing DIC (digital image correlation) for the purpose of quantifying the strain field and tracking crack growth. A threshold behavior was observed, in which higher-pressure pre-load resulted in cracks forming, while lower-pressure pre-load vented across the face of the explosive. This report presents the preliminary results, discusses the observations, enumerates hypotheses regarding the observed behavior, identifies lessons learned, and outlines a path forward for the next round of testing. Proof testing was only recently concluded and considerable additional analysis is required. These data will be valuable for the ongoing development of a constitutive mechanical and cracking failure model that will aid in predicting explosive response in mechanical impact scenarios.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Turbulent mixing in supercritical jets: effect of compressibility factor and inflow condition

Fuel injection and turbulent mixing at supercritical pressures determines ignition and combustion in numerous engineering applications. Flow evolution under such conditions is characterized by strong non-linear coupling between dynamics, transport coefficients, and thermodynamics. Experimental studies observe that the jets injected at supercritical pressures exhibit significantly different dynamics from the jets at subcritical conditions, owing to the lack of distinct liquid and gas phases in supercritical state. Thus, the averaged flow quantities such as the potential core length, jet spatial growth rate and velocity decay profiles differ in the two conditions, resulting in different mixed-fluid distributions. In this study, turbulent jet direct numerical simulations (DNS) are performed to examine the variations in flow statistics between injection of Nitrogen (N₂) in Nitrogen (N₂) at both subcritical (perfect-gas) and supercritical conditions. In all cases, isothermal round jets at Reynolds number (Re_{D}), based on jet diameter (D) and jet orifice velocity (U₀), of 5000 are considered. For mixing analyses, a passive scalar transported with the flow is examined.

Sharan, Nek↗

Thermodynamic properties of ε -Fe with thermal electronic excitation effects on vibrational spectra

The thermodynamic properties of hexagonal-close-packed iron (ε–Fe) are essential for investigating the internal structure and dynamic properties of planetary cores. Despite their importance to planetary sciences, experimental investigations of ε–Fe at relevant conditions are still challenging. Therefore, ab initio calculations are crucial to elucidating the thermodynamic properties of this system. Here, we use a free energy calculation scheme based on the phonon gas model compatible with temperature-dependent phonon frequencies. We investigate the effects of electronic thermal excitations, which introduces a temperature dependence on phonon frequencies, and the implication for the thermodynamic properties of ε–Fe at extreme pressure (P) and temperature (T) conditions. We disregard phonon-phonon interactions, i.e., anharmonicity and their effect on phonon frequencies. Nevertheless, the current scheme is also applicable to T -dependent anharmonic frequencies. We conclude that the impact of thermal electronic excitations on vibrational properties is not significant up to ~4000 K at 200 GPa but should not be ignored at higher temperatures or pressures. However, the static free energy F st must always include the effect of thermal excitation fully in a continuum of T. Furthermore, our results for isentropic equations of state show good agreement with data from recent ramp compression experiments up to 1400 GPa conducted at the National Ignition Facility.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

200-fold increase in dynamic strength of platinum at 430 GPa without a phase transformation

Here, the high-pressure strength of solid platinum is studied at the National Ignition Facility via Rayleigh-Taylor ripple growth under ramp compression. Laser-driven experiments reached pressures up to 430 GPa, collecting velocimetry and radiography data. Despite no phase transformation, the observed ripple growth aligns with hydrodynamic simulations using an amplified Steinberg-Guinan model, resulting in a 200-fold increase in strength. Molecular dynamics simulations of platinum ramp compression yield similar von Mises stress at comparable high pressure and high strain rate conditions. These findings represent the highest-pressure strength measurements ever achieved for platinum and offer critical insight into its significant strengthening behavior under high pressure and strain rate conditions.

Righi, Gaia [Lawrence Livermore National Laborator↗

Autoignition of CRC diesel surrogates at low temperature combustion conditions: Rapid compression machine experiments and modeling

As federal programs require increasingly stringent engine emissions and fuel economy standards, these ambitions can only be met if next-generation combustion technology is developed focusing on high-efficiency and low-emissions engines. Recent research has indicated the need to operate engines at higher compression ratios and with low temperature combustion (LTC) to achieve the needed gains in engine efficiency and reductions in emissions. Because there is a lack of understanding of the chemistry of diesel fuel components and their mixtures at these LTC conditions, this limits the ability to develop predictive chemical kinetic models that can be used to optimize engine combustion. The current study aims to fill in gaps in fundamental combustion data on surrogate fuel mixtures relevant to diesel fuels. Specifically, four multicomponent diesel surrogates formulated by the Coordinating Research Council (CRC) to emulate an ultra-low-sulfur research-grade #2 certification diesel fuel (CFA), namely V0a (4 components), V0b (5 components), V1 (8 components), and V2 (9 components), have been investigated in a rapid compression machine (RCM) through determination of total and first-stage ignition delay times. Autoignition characteristics of lean to rich fuel/O 2 /N 2 mixtures, for the four CRC surrogates and CFA, have been measured using an RCM at LTC relevant pressures and temperatures, in the ranges of 10–20 bar and 650–1000 K, respectively. The equivalence ratios have been varied by independently changing the oxygen mole fraction and the fuel mole fraction in the test mixtures, thereby illustrating the individual effects of oxygen concentration and fuel loading on diesel autoignition. Autoignition results of these four CRC surrogates are compared among them and with those of CFA. Some degree of agreement in autoignition response between each CRC surrogate and CFA is observed, while discrepancies are also identified and discussed. In addition, a detailed chemical kinetic model for diesel surrogates has been developed and validated against these newly-acquired RCM data. We find that this model shows reasonable agreement with the overall ignition delay time results of the current RCM experiments. Chemical kinetic analyses of the developed model were further conducted to help identify the reactions controlling the autoignition processes and the consumption of fuel components in CRC surrogates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗