Search NASA⌕ Search

SEARCH · Search NASA

Results for “control electronics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Instruction manual, Optical Effects Module, Model OEM

The Optical Effects Module Model OEM-1, a laboratory prototype instrument designed for the automated measurement of radiation transmission and scattering through optical samples, is described. The system comprises two main components: the Optical Effects Module Enclosure (OEME) and the Optical Effects Module Electronic Controller and Processor (OEMCP). The OEM is designed for operation in the near UV at approximately 2540A, corresponding to the most intense spectral line activated by the mercury discharge lamp used for illumination. The radiation from this source is detected in transmission and reflection through a number of selectable samples. The basic objective of this operation is to monitor in real time the accretion of possible contamination on the surface of these samples. The optical samples are exposed outside of the OEME proper to define exposure conditions and to separate exposure and measurement environments. Changes in the transmissivity of the sample are attributable to surface contamination or to bulk effects due to radiation. Surface contamination will increase radiation scattering due to Rayleigh-Gans effect or to other phenomena, depending on the characteristics size of the particulate contaminants. Thus, also scattering from the samples becomes a part of the measurement program.

Source record↗

Magnetically suspended reaction wheels

Magnetic suspensions offer several advantages over conventional bearings, arising because of the contactless nature of the load support. In application to spacecraft reaction wheels, the advantages are low drag torque, wearfree, unlubricated, vacuum-compatible operation, and unlimited life. By the provision of redundancy in the control electronics, single-point failures are eliminated. The rational for selection of a passive radial, active axial, dc magnetic suspension is presented, and the relative merits of 3-loop and single-loop magnetic suspensions are discussed. The design of a .678 N-m-sec (.5 ft-lb-sec) reaction wheel using the single loop magnetic suspension was developed; the design compares favorably with current ball bearing wheels in terms of weight and power.

Sabnis, A. V.↗

Postflight analysis for Delta Program Mission no. 113: COS-B Mission

On 8 August 1975, the COS-B spacecraft was launched successfully from the Western Test Range (Delta Program Mission No. 113). The launch vehicle was a three stage Extended Long Tank Delta DSV-3P-11B vehicle. Postflight analyses performed in connection with flight are presented. Vehicle trajectory, stage performance, vehicle reliability and the propulsion, guidance, flight control, electronics, mechanical and structural systems are evaluated.

Source record↗

Results from the EPL monkey-pod experiment conducted as part of the 1974 NASA/Ames shuttle CVT-2

The participation of the Environmental Physiology Laboratory (EPL) in the general purpose laboratory concept verification test 3 is documented. The EPL Monkey-Pod Experiment was designed to incorporate a 10-12 kg, pig tailed monkey, Macaca nemestrina, into the pod and measure the physiological responses of the animal continuously. Four major elements comprise the EPL Monkey-Pod Experiment System: (1) a fiberglass pod containing the instrumented monkey plus feeder and watering devices, (2) an inner console containing the SKYLAB mass spectrometer with its associated valving and electronic controls, sensing, control and monitoring units for lower body negative pressure, feeder activity, waterer activity, temperatures, and gas metabolism calibration, (3) an umbilical complex comprising gas flow lines and electrical cabling between the inner and outer console and (4) an outer console in principle representing the experiment support to be provided from general spacecraft sources.

Rahlmann, D. F.↗

Results from the EPL monkey-pod flight experiments conducted aboard the NASA/Ames CV-990, May 1976

The participation of the Environmental Physiology Laboratory (EPL) in the general purpose laboratory concept verification test 3 is documented. The EPL Monkey-Pod Experiment was designed to incorporate a 10-12 kg, pig tailed monkey, Macaca nemestrina, into the pod and measure the physiological responses of the animal continously. Four major elements comprise the EPL Monkey-Pod Experiment System: (1) a fiberglass pod containing the instrumented monkey plus feeder and watering devices, (2) an inner console containing the SKYLAB mass spectrometer with its associated valving and electronic controls, sensing, control and monitoring units for lower body negative pressure, feeder activity, waterer activity, temperatures, and gas metabolism calibration, (3) an umbilical complex comprising gas flow lines and electrical cabling between the inner and outer console and (4) an outer console in principle representing the experiment support to be provided from general space craft sources.

Rahlmann, D. F.↗

Unified Mars detection system

A life-detection system is described which is designed to detect and characterize possible Martian biota and to gather information about the chemical environment of Mars, especially the water and amino acid contents of the soil. The system is organized around a central mass spectrometer that can sensitively analyze trace gases from a variety of different experiments. Some biological assays and soil-chemistry tests that have been performed in the laboratory as typical experiment candidates for the system are discussed, including tests for soil-organism metabolism, measurements of soil carbon contents, and determinations of primary aliphatic amines (amino acids and protein) in soils. Two possible test strategies are outlined, and the operational concept of the detection system is illustrated. Detailed descriptions are given for the mass spectrometer, gas inlet, incubation box, test cell modules, seal drive mechanism, soil distribution assembly, and electronic control system.

Martin, J. P.↗

Save power in AC induction motors

Relatively simple and inexpensive circuitry improves power factor and reduces power dissipation in induction motors operating below full load. Electronic control loop conserves energy by reducing voltage applied to lightly loaded motor. Circuit forces motor to run at constant predetermined optimum power factor, regardless of load or line voltage variations. Solid-state switch varies voltage.

Nola, F. J.↗

Mode-locked frequency doubled Nd:YAG laser

The design, fabrication, test, and delivery of two mode-locked, frequency doubled Nd:YAG laser systems are described. Each system was comprised of two units, the laser head and optics on an Invar plate and the electronics control unit in a relay rack chassis panel. Laser number one operated at a repetition rate of 400 MHz and was designed for use in an optical communication system. Laser number two operated at 200 MHz repetition rate and was designed for optical ranging and target signature experiments. Both lasers had a pulse width of 200 ps at the 10% amplitude points at 1.064 micrometer wavelength (150 ps at 0.532 micrometers) with an amplitude stability of + or - 4%. Output power exceeded the design goals.

Brookman, J. S.↗

Electromechanical flight control actuator, volume 1

An electromechanical actuator was developed that will follow a proportional control command with minimum wasted energy to demonstrate the feasibility of meeting space vehicle actuator requirements using advanced electromechanical concepts. The approach was restricted to a four-channel redundant configuration. Each channel has independent drive and control electronics, a brushless electric motor with brake, and velocity and position feedback transducers. A differential gearbox sums the output velocities of the motors. Normally, two motors are active and the other two are braked.

Source record↗

Energy consumption program: A computer model simulating energy loads in buildings

The JPL energy consumption computer program developed as a useful tool in the on-going building modification studies in the DSN energy conservation project is described. The program simulates building heating and cooling loads and computes thermal and electric energy consumption and cost. The accuracy of computations are not sacrificed, however, since the results lie within + or - 10 percent margin compared to those read from energy meters. The program is carefully structured to reduce both user's time and running cost by asking minimum information from the user and reducing many internal time-consuming computational loops. Many unique features were added to handle two-level electronics control rooms not found in any other program.

Stoller, F. W.↗

Modification of the continuous flow diffusion chamber for use in zero-gravity

The design philosophy and performance characteristics of the continuous flow diffusion chamber developed for use in ground-based simulation of some of the experiments planned for the atmospheric cloud physics laboratory during the first Spacelab flight are discussed. Topics covered include principle of operation, thermal control, temperature measurement, tem-powered heat exchangers, wettable metal surfaces, sample injection system, and control electronics.

Keyser, G.↗

Nodding feed antenna for communications with satellites in synchronous orbit

The design, fabrication, and performance of a parabolic, ground receiving antenna system with a feed that nods in one axis producing a maximum beam deviation 1.1 deg from boresight is described. The antenna design was: (1)to lower the weight (and the subsequent cost) of the supporting structure and the actuator motors for a tracking antenna by moving just the feed; (2) to use a manual tracking system eliminating the need for expensive electronic controls or computers; (3) to provide for several hours of unattended operation; and (4)to permit operation of the antenna by unskilled personnel. Also described are some physical and orbital phenomenon that effect the operation or design of the antenna. One is the motion of a nearly geostationary satellite due to gravitational forces from the sun, the moon, and other stellar bodies. Others are the rotation of the nodding axis and the feed polarization as a function of the location of the station on the earth. A comparison of per unit cost was made for one unit and a quantity of 100.

Smetana, J.↗

Real time digital propulsion system simulation for manned flight simulators

The QCSEE (Quiet, Clean Short-haul Experimental Engine) Program was initiated by NASA to develop and demonstrate propulsion system technology for an advanced commercial STOL aircraft. One of the specific technical objectives was to provide technology for digital electronic control of future commercial engines. An element of this technology development was to evaluate the digital control in a simulated flight environment. In this connection a simulation program was initiated to evaluate the QCSEE UTW (Under-the-Wing) digital control system over a range of conditions encountered in typical airport operations. The goal of the simulation effort was to derive a real time digital propulsion simulation which could be integrated into a multiengine aircraft simulation. A summary is provided of the accomplishments which have been made in this program.

Mihaloew, J. R.↗

LED instrument approach instruction display

A display employing light emitting diodes (LED's) was developed to demonstrate the feasibility of such displays for presenting landing and navigation information to reduce the workload of general aviation pilots during IFR flight. The display consists of a paper tape reader, digital memory, control electronics, digital latches, and LED alphanumeric displays. A presentable digital countdown clock-timer is included as part of the system to provide a convenient means of monitoring time intervals for precise flight navigation. The system is a limited capability prototype assembled to test pilot reaction to such a device under simulated IFR operation. Pilot opinion indicates that the display is helpful in reducing the IFR pilots workload when used with a runway approach plate. However, the development of a compact, low power second generation display was recommended which could present several instructions simultaneously and provide information update capability. A microprocessor-based display could fulfill these requirements.

Meredith, B. D.↗

A summary of NASA/Air Force full scale engine research programs using the F100 engine

A full scale engine research (FSER) program conducted with the F100 engine is presented. The program mechanism is described and the F100 test vehicles utilized are illustrated. Technology items were addressed in the areas of swirl augmentation, flutter phenomenon, advanced electronic control logic theory, strain gage technology and distortion sensitivity. The associated test programs are described. The FSER approach utilizes existing state of the art engine hardware to evaluate advanced technology concepts and problem areas. Aerodynamic phenomenon previously not considered by design systems were identified and incorporated into industry design tools.

Deskin, W. J.↗

Flight performance of the High Energy Astronomy Observatory /HEAO 1/ power subsystem

The design and flight performance of the HEAO-1 power subsystem is described. Solar array power analysis and test data are compared to orbital performance. The batteries are described along with parametric cell tests which led to the temperature-compensated voltage limits used in the charge controls. Battery life test results, used for verification of battery charger temperature-compensated voltage limits, are compared with orbital performance. The control electronics are

Reppucci, G. M.↗