Results for “core optimization” — Page 47

NASA NTRS2018

Technology Maturity for the Habitable-zone Exoplanet Imaging Mission (HabEx) Concept

HabEx Architecture A is a 4m unobscured telescope mission concept optimized for direct imaging and spectroscopy of potentially habitable exoplanets, and also enables a wide range of general astrophysics science. The exoplanet detection and characterization drives the enabling core technologies. A hybrid starlight suppression approach of a starshade and coronagraph diversifies technology maturation risk. In this paper we assess these exoplanet-driven technologies, including elements of coronagraphs, starshades, mirrors, jitter mitigation, wavefront control, and detectors. By utilizing high technology readiness solutions where feasible, and identifying required technology development that can begin early, HabEx will be well positioned for assessment by the community in 2020 Astrophysics Decadal Survey.

Warwick, Steve↗

DOE OSTI2017

Grid pressure drop prediction in a fuel assembly

In fuel assembly, spacer grids have strong effects on pressure drop and other thermal-hydraulic behaviors. Considering the design and safety operation of a reactor, it is important to predict pressure drop accurately in the fuel assembly. For a mixed core, a reactor with mixed fuel designs in the reactor core, undesired cross flow were often caused by differences in pressure drop among neighboring bundles. The pressure drop is often estimated for designs of new reactor core fuel assemblies. In the past, due to complex flow conditions in fuel assembly, the pressure drop of a fuel assembly relied greatly on costly and time-consuming full length thermal hydraulic tests. Some empirical pressure drop correlations and CFD methodology were applied, however, only limited to a single gird span. Without considering pressure drop in the entire fuel assembly it is quite difficult to optimize the fuel assembly design. Most experimental fuel assemblies consist of mixing vane grids (MVG) and simple support grids (SSG). The MVG's were the main tested spacer grids in the reactor and SSG's were used only in experimental study to support the fuel assembly. In fuel reactor core, the fuel assembly heats the coolant, which could turn the single-phase water system into a two-phase flow system and eventually lead to critical heat flux (CHF). Because of the complexity of phase change, it is very difficult to predict pressure drop in rod bundles with two-phase flow. In this paper, a new method to predict the pressure drop in the fuel assembly is proposed and verified by experimental data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2017

Nitrogen–doped graphitized carbon shell encapsulated NiFe nanoparticles: A highly durable oxygen evolution catalyst

Oxygen evolution reaction (OER) plays a crucial role in various energy conversion devices such as water electrolyzers and metal–air batteries. Precious metal catalysts such as Ir, Ru and their oxides are usually used for enhancing reaction kinetics but are limited by their scarce resource. The challenges associated with alternative non–precious metal catalysts such as transition metal oxides and (oxy)hydroxides etc. are their low electronic conductivity and durability. Herein, we report a highly active (360 mV overpotential at 10 mA cm–2GEO) and durable (no degradation after 20000 cycles) OER catalyst derived from bimetallic metal–organic frameworks (MOFs) precursors. This catalyst consists of NiFe nanoparticles encapsulated by nitrogen–doped graphitized carbon shells. The electron-donation/deviation from Fe and tuned electronic structure of metal cores by Ni are revealed to be primary contributors to the enhanced OER activity, whereas N concentration contributes negligibly. We further demonstrated that the structure and morphology of encapsulating carbon shells, which are the key factors influencing the durability, are facilely controlled by the chemical state of precursors.

Environmental Molecular Sciences Laboratory↗

NASA NTRSDate not supplied

Preliminary Design of a Distributed Facesheet Acoustic Liner for Broadband Acoustic Attenuation

The purpose of this study is to investigate the acoustic performance of a liner with a distributed facesheet and a uniform depth core for broadband attenuation. The distributed facesheet is comprised of a cluster of three distinct cell resonators of varying hole diameter and porosity replicated over the active liner treatment area. A target frequency range of 1000 to 2000 Hz and an attenuation metric of 10 dB are chosen. An optimizer is used to determine the optimal facesheet designs for flow conditions of Mach 0.0 and Mach 0.3. The samples are tested in the Grazing Flow Impedance Tube at NASA Langley Research Center. The two liners are shown to achieve at least 10 dB attenuation over frequency ranges of 700 and 400 Hz, respectively, when tested at their respective designed flow speeds. This study demonstrate that a distributed facesheet with a uniform depth core can be successfully used to achieve broadband sound absorption.

acoustic liners↗

DOE OSTI2021

Phosphorolytic degradation of leaf starch via plastidic α-glucan phosphorylase leads to optimized plant growth and water use efficiency over the diel phases of Crassulacean acid metabolism

In plants with Crassulacean acid metabolism (CAM), it has been proposed that the requirement for nocturnal provision of phosphoenolpyruvate as a substrate for CO 2 uptake has resulted in a re-routing of chloroplastic starch degradation from the amylolytic route to the phosphorolytic route. To test this hypothesis, we generated and characterized four independent RNAi lines of the obligate CAM species Kalanchoë fedtschenkoi with a >10-fold reduction in transcript abundance of plastidic α-glucan phosphorylase (PHS1). The rPHS1 lines showed diminished nocturnal starch degradation, reduced dark CO 2 uptake, a reduction in diel water use efficiency (WUE), and an overall reduction in growth. A re-routing of starch degradation via the hydrolytic/amylolytic pathway was indicated by hyperaccumulation of maltose in all rPHS1 lines. Further examination indicated that whilst operation of the core circadian clock was not compromised, plasticity in modulating net dark CO 2 uptake in response to changing photoperiods was curtailed. The data show that phosphorolytic starch degradation is critical for efficient operation of the CAM cycle and for optimizing WUE. This finding has clear relevance for ongoing efforts to engineer CAM into non-CAM species as a means of boosting crop WUE for a warmer, drier future.

59 BASIC BIOLOGICAL SCIENCES↗

NASA NTRS2023

Development of Two High-Energy Bus ‘Cores’ for Rapid Support of Low-TRL and Educational Payloads: A Software-Configured EPS Combined with Flexible C&DH

For several years the TechEdSat flight series (TES-n), developed by the Nano Orbital Workshop (NOW) group at NASA Ames, has relied upon an in-house developed unit to serve both EPS (Electrical Power System) and C&DH (Command and Data Handling) roles along with low data-rate telemetry functions, i.e., serving as the ‘core’ of the spacecraft bus. This ‘core’ has a considerable task given the rapid cadence of the TES program and the typically low-TRL of payloads; configurability and compatibility are key to prevent mission-specific hardware. However, at only 15 watts the current core has become insufficient to support the program’s growing missions and increasingly demanding payloads. To this end, the NOW program is developing new cores to support two TES mission classes: a single-PCB ‘MiniCore’ designed to support 80-watt missions 6U or smaller in LEO, and a three-PCB, radiation-tolerant ‘StackCore’ designed to support 6U and larger missions over 500 watts in LEO and beyond. The ‘MiniCore’ design consists of three main segments: a processor-agnostic C&DH, a software-configured EPS, and a backup low data-rate radio. The design philosophy was to enable rapid-manufacture in a turbulent supply chain, hence the design consists of COTS parts with a focus on those able to be drop-in replaced with radiation-tolerant versions when demanded by the mission. As a single PC-104 sized circuit board, power density and ease of integration also dominated design, demanding the use of modern features such as single-point USB-C for easy charging and monitoring of the spacecraft on the ground. The ‘MiniCore’ can support 80 watts of load, 140 watt-hours of storage, and over 20 watts of optimized solar generation with extensive power monitoring throughout. The ‘MiniCore’ supports one battery pack, six solar-panels, six loads, five actuators, Iridium SBD, and an internal 802.15.4 network. Additionally, the processor-agnostic design can accept any PJRC Teensy 3.x or Adafruit Feather microcontroller unit to enable processor scaling with mission requirements or environment. It is expected a development unit of this design will be completed before conference. The ‘StackCore’ design consists of three stacked PC-104 sized circuit boards: one dedicated to power generation and storage, one dedicated to power distribution, and one dedicated to C&DH tasks. This delineation is necessary to support the transition from highly integrated ICs to discrete analog circuitry, enabling a primarily analog control power system able to operate without software in a radiation environment with finer monitoring compared to the ‘MiniCore’ design. The planned base architecture supports over 500 watts of load, 250 watt-hours of storage, and over 80 watts of optimized solar generation. The power distribution board allows for the use of daughter cards hosting custom converters or interfaces for payloads, in addition to the software-configured supplies used on the ‘MiniCore’. This core stack will be managed by a Vorago ARM M4 microcontroller and support the same wireless communications as the ‘MiniCore’, with optional integration of a NOW S-band radio and attitude determination sensors for ‘black box’ functionality. It is expected the prototype will still be in development during conference.

Spacecraft↗

NASA NTRSDate not supplied

Development of Two High-Energy Bus ‘Cores’ for Rapid Support of Low-TRL and Educational Payloads: A Software-Configured EPS Combined with Flexible C&DH

For several years the TechEdSat flight series (TES-n), developed by the Nano Orbital Workshop (NOW) group at NASA Ames, has relied upon an in-house developed unit to serve both EPS (Electrical Power System) and C&DH (Command and Data Handling) roles along with low data-rate telemetry functions, i.e., serving as the ‘core’ of the spacecraft bus. This ‘core’ has a considerable task given the rapid cadence of the TES program and the typically low-TRL of payloads; configurability and compatibility are key to prevent mission-specific hardware. However, at only 15 watts the current core has become insufficient to support the program’s growing missions and increasingly demanding payloads. To this end, the NOW program is developing new cores to support two TES mission classes: a single-PCB ‘MiniCore’ designed to support 80-watt missions 6U or smaller in LEO, and a three-PCB, radiation-tolerant ‘StackCore’ designed to support 6U and larger missions over 500 watts in LEO and beyond. The ‘MiniCore’ design consists of three main segments: a processor-agnostic C&DH, a software-configured EPS, and a backup low data-rate radio. The design philosophy was to enable rapid-manufacture in a turbulent supply chain, hence the design consists of COTS parts with a focus on those able to be drop-in replaced with radiation-tolerant versions when demanded by the mission. As a single PC-104 sized circuit board, power density and ease of integration also dominated design, demanding the use of modern features such as single-point USB-C for easy charging and monitoring of the spacecraft on the ground. The ‘MiniCore’ can support 80 watts of load, 140 watt-hours of storage, and over 20 watts of optimized solar generation with extensive power monitoring throughout. The ‘MiniCore’ supports one battery pack, six solar-panels, six loads, five actuators, Iridium SBD, and an internal 802.15.4 network. Additionally, the processor-agnostic design can accept any PJRC Teensy 3.x or Adafruit Feather microcontroller unit to enable processor scaling with mission requirements or environment. It is expected a development unit of this design will be completed before conference. The ‘StackCore’ design consists of three stacked PC-104 sized circuit boards: one dedicated to power generation and storage, one dedicated to power distribution, and one dedicated to C&DH tasks. This delineation is necessary to support the transition from highly integrated ICs to discrete analog circuitry, enabling a primarily analog control power system able to operate without software in a radiation environment with finer monitoring compared to the ‘MiniCore’ design. The planned base architecture supports over 500 watts of load, 250 watt-hours of storage, and over 80 watts of optimized solar generation. The power distribution board allows for the use of daughter cards hosting custom converters or interfaces for payloads, in addition to the software-configured supplies used on the ‘MiniCore’. This core stack will be managed by a Vorago ARM M4 microcontroller and support the same wireless communications as the ‘MiniCore’, with optional integration of a NOW S-band radio and attitude determination sensors for ‘black box’ functionality. It is expected the prototype will still be in development during conference.

Spacecraft↗

NASA NTRSDate not supplied

Development of Two High-Energy Bus ‘Cores’

For several years the TechEdSat flight series (TES-n), developed by the Nano Orbital Workshop (NOW) group at NASA Ames, has relied upon an in-house developed unit to serve both EPS (Electrical Power System) and C&DH (Command and Data Handling) roles along with low data-rate telemetry functions, i.e., serving as the ‘core’ of the spacecraft bus. This ‘core’ has a considerable task given the rapid cadence of the TES program and the typically low-TRL of payloads; configurability and compatibility are key to prevent mission-specific hardware. However, at only 15 watts the current core has become insufficient to support the program’s growing missions and increasingly demanding payloads. To this end, the NOW program is developing new cores to support two TES mission classes: a single-PCB ‘MiniCore’ designed to support 80-watt missions 6U or smaller in LEO, and a three-PCB, radiation-tolerant ‘StackCore’ designed to support 6U and larger missions over 500 watts in LEO and beyond. The ‘MiniCore’ design consists of three main segments: a processor-agnostic C&DH, a software-configured EPS, and a backup low data-rate radio. The design philosophy was to enable rapid-manufacture in a turbulent supply chain, hence the design consists of COTS parts with a focus on those able to be drop-in replaced with radiation-tolerant versions when demanded by the mission. As a single PC-104 sized circuit board, power density and ease of integration also dominated design, demanding the use of modern features such as single-point USB-C for easy charging and monitoring of the spacecraft on the ground. The ‘MiniCore’ can support 80 watts of load, 140 watt-hours of storage, and over 20 watts of optimized solar generation with extensive power monitoring throughout. The ‘MiniCore’ supports one battery pack, six solar-panels, six loads, five actuators, Iridium SBD, and an internal 802.15.4 network. Additionally, the processor-agnostic design can accept any PJRC Teensy 3.x or Adafruit Feather microcontroller unit to enable processor scaling with mission requirements or environment. It is expected a development unit of this design will be completed before conference. The ‘StackCore’ design consists of three stacked PC-104 sized circuit boards: one dedicated to power generation and storage, one dedicated to power distribution, and one dedicated to C&DH tasks. This delineation is necessary to support the transition from highly integrated ICs to discrete analog circuitry, enabling a primarily analog control power system able to operate without software in a radiation environment with finer monitoring compared to the ‘MiniCore’ design. The planned base architecture supports over 500 watts of load, 250 watt-hours of storage, and over 80 watts of optimized solar generation. The power distribution board allows for the use of daughter cards hosting custom converters or interfaces for payloads, in addition to the software-configured supplies used on the ‘MiniCore’. This core stack will be managed by a Vorago ARM M4 microcontroller and support the same wireless communications as the ‘MiniCore’, with optional integration of a NOW S-band radio and attitude determination sensors for ‘black box’ functionality. It is expected the prototype will still be in development during conference.

Avery Brock↗

DOE OSTI2018

Optimizing neutron imaging line of sight locations for maximizing sampling of the cold fuel density in inertial confinement fusion implosions at the National Ignition Facility

We report that neutron imaging provides a ready measurement of the shape of the “hot spot” core of an inertial confinement fusion implosion. The 14-MeV neutrons emitted by deuterium-tritium reactions are imaged at the National Ignition Facility using a pinhole array onto a scintillator, and the images are recorded on a camera. By changing the gate time of the camera, lower energy neutrons, downscattered by the cold fuel surrounding the hot spot, are recorded. The cold fuel density can be reconstructed using the two images. The kinematics of the scattering coupled with the scattering cross sections restrict the angular extent of the cold fuel sampled, with the backside of the implosion not being sampled at all. This work demonstrates the limited region of the cold fuel measured by the current line of sight (40%). Finally, at completion of the three planned lines of sight, 79% of the cold fuel will be sampled.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2020

Optimization of Energy Flow through Synthetic Metabolic Modules and Regulatory Networks in a Model Photosynthetic Eukaryotic Microbe

Photosynthetic organisms have recently gained considerable attention for a role in development of renewable energy sources. Genome-enabled systems biology methods, coupled with functional and synthetic genomics, present opportunities to develop sustainable and economical applications such as fuel production within the next 10 to 15 years. However, optimization of light-driven metabolism for biomass or biofuel production will require a detailed systems biology understanding of photosynthetic processes and cellular metabolism. Genome-scale metabolic models (GEMs) are at the core of systems analysis of cellular processes and form a common organizational framework for analyses of data resulting from functional genomics experimental work and computational studies. Therefore, there is a clear demand for high quality photosynthetic model organisms and the appropriate computational tools that enable systems analysis of light-driven metabolism. Through research conducted we expanded the currently available repertoire of photosynthetic GEMs to include the commercially valuable model diatom Phaeoctylum tricornutum. Diatoms have a peculiar and distinct evolutionary footprint and represent a major eukaryotic lineage that is taxonomically and functionally distinct from green and red algae and vascular plants. Therefore, the true potential for light-driven metabolism aimed at biofuel production remains poorly understood at a systems level for a large subset of the global diversity of photosynthetic organisms. The metabolic capabilities of P. tricornutum were comparatively modeled with those from other photosynthetic groups in order to elucidate the occurrence of metabolic traits within and between phototrophs. Additionally, this research resulted in significant extension of the COnstraints Based Reconstruction and Analysis (COBRA) Toolbox to accommodate the crucial need for infrastructure required for ‘omics data integration and analysis in the context of genome-scale models. Therefore, the proposed research achieved two important goals. First, within the broad scope of photosynthetic organisms, we functionally compared and, as a result, identified cellular processes that require optimization in order to enable deployment as biofuel feedstock. Second, the proposed research resulted in development of key computational infrastructure, which can be further extended to other biological systems, that is currently lacking but necessary for multiple ‘omics data integration.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2022

Additive manufacturing of continuous carbon fiber-reinforced SiC ceramic composite with multiple fiber bundles by an extrusion-based technique

Due to the high cost, complex preparation process and difficulty in structural design, the traditional methods for carbon fiber-reinforced SiC ceramic composite preparation have great limitations. This paper presents a technique for the additive manufacturing multiple continuous carbon fiber bundle-reinforced SiC ceramic composite with core-shell structure using an extrusion-based technique. A conventional nozzle system was modified to print simultaneously a water-based SiC paste with continuous carbon fibers. Different levels of binder contents were investigated to optimize the stickiness, viscosity, thixotropy and viscoelasticity of the paste. After sintering, SiC whiskers were generated on the surface of fiber, which is conjectured to be due to the reaction between SiO and carbon fiber at high temperature. The continuous carbon fiber-reinforced SiC ceramic composite exhibited non-brittle fracture. In conclusion, the flexural strength of the additively manufactured Cf/SiC composites improved from 162 MPa with no fiber bundles to a maximum of 219 MPa with three fiber bundles.

36 MATERIALS SCIENCE↗

DOE OSTI2017

Evaluating the networking characteristics of the Cray XC-40 Intel Knights Landing-based Cori supercomputer at NERSC

There are many potential issues associated with deploying the Intel Xeon Phi™ (code named Knights Landing [KNL]) manycore processor in a large-scale supercomputer. One in particular is the ability to fully utilize the high-speed communications network, given that the serial performance of a Xeon Phi TM core is a fraction of a Xeon®core. In this paper, we take a look at the trade-offs associated with allocating enough cores to fully utilize the Aries high-speed network versus cores dedicated to computation, e.g., the trade-off between MPI and OpenMP. In addition, we evaluate new features of Cray MPI in support of KNL, such as internode optimizations. We also evaluate one-sided programming models such as Unified Parallel C. We quantify the impact of the above trade-offs and features using a suite of National Energy Research Scientific Computing Center applications.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2021

Ion-temperature-gradient stability near the magnetic axis of quasisymmetric stellarators

Abstract The stability of the ion-temperature gradient mode in quasisymmetric stellarators is assessed. This is performed using a set of analytical estimates together with linear gyrokinetic simulations. The peak growth rates, their corresponding real frequencies and wave-vectors are identified. A comparison is made between a first-order near-axis expansion model and eleven realistic designs obtained using numerical optimization methods. It is found that while the near-axis expansion is able to replicate the growth rates, real frequencies and perpendicular wave-vector at the inner core (both using simplified dispersion relations and first-principle gyrokinetic simulations), it leads to an overestimation of the growth rate at larger radii. An approximate analytic solution of the ITG dispersion relation for the non-resonant limit suggests growth rates could be systematically higher in quasi-axisymmetric (QA) configurations compared to quasi-helically (QH) symmetric ones. However except for very close to the axis, linear gyrokinetic simulations do not show systematic differences between QA and QH configurations.

Physics↗

DOE OSTI2020

Pore-scale view of microbial turnover: combining 14 C imaging, μCT, and zymography after adding soluble carbon to soil pores of specific sizes

The location of microorganisms and substrates within soil pore networks plays a crucial role for organic carbon (C) processing, its microbial utilization and turnover, and has direct consequences for C and nutrient cycling. An optimal approach to quantify responses to new C inputs from microorganisms residing in specific pores is the addition of new C to pores of target sizes in undisturbed soil cores. We used the matric potential approach to add 14 C labeled glucose to small (< 40 μm, root free) or large (60-180 μm, potentially inhabited by roots) pores of undisturbed soil cores. Localization of glucose-derived C via 14 C imaging was related to pore size distributions and connectivity, characterized via X-ray computed micro-tomography (μCT), and to β-glucosidase activity, characterized via zymography. After two-week incubations, 1.3 times more glucose was mineralized ( 14 CO 2 ) when it was added to the large pores, however more 14 C remained in microbial biomass when glucose was added to the small pores. Consequently, while utilizing the same amounts of easily available C, the microorganisms localized in the large pores had faster turnover compared to microorganisms in small pores. Stronger associations between β-glucosidase activity and glucose-derived C were observed when glucose was added to the large pores. We conclude that 1) the matric potential approach allows placing, albeit not exactly, soluble substrates into pores of target diameter range, and 2) microorganisms localized in large pores respond to new C inputs with faster turnover, greater growth, and more intensive enzyme production compared to those inhabiting the small pores.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1982

ACCESS computer program for the synthesis of large structural systems

The structural-synthesis computer code ACCESS-3, originally limited to the optimization of relatively simple problems involving truss, membrane, and shear panel elements, has been restructured to make it applicable to structures with a larger number of degrees-of-freedom, design variables, and constraints. The modifications made allow the use of six degrees-of-freedom per node and permit the out-of-core solution of large matrix equations encountered at the analysis stage. Also, finite elements which permit pure bending as well as combined bending and membrane (axial) behavior have been added to satisfy the need for a more comprehensive set of elements. Like its predecessor, the new version of the program combines the approximation concepts with primal or dual formulations to provide an efficient optimization tool.

Fleury, C.↗

DOE OSTI2021

Mixed Precision Fermi-Operator Expansion on Tensor Cores from a Machine Learning Perspective

Here we present a second-order recursive Fermi-operator expansion scheme using mixed precision floating point operations to perform electronic structure calculations using tensor core units. A performance of over 100 teraFLOPs is achieved for half-precision floating point operations on Nvidia’s A100 tensor core units. The second-order recursive Fermi-operator scheme is formulated in terms of a generalized, differentiable deep neural network structure, which solves the quantum mechanical electronic structure problem. We demonstrate how this network can be accelerated by optimizing the weight and bias values to substantially reduce the number of layers required for convergence. We also show how this machine learning approach can be used to optimize the coefficients of the recursive Fermi-operator expansion to accurately represent the fractional occupation numbers of the electronic states at finite temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2017

Preparing NERSC users for Cori, a Cray XC40 system with Intel many integrated cores

The newest NERSC supercomputer Cori is a Cray XC40 system consisting of 2,388 Intel Xeon Haswell nodes and 9,688 Intel Xeon-Phi “Knights Landing” (KNL) nodes. Compared to the Xeon-based clusters NERSC users are familiar with, optimal performance on Cori requires consideration of KNL mode settings; process, thread, and memory affinity; fine-grain parallelization; vectorization; and use of the high-bandwidth MCDRAM memory. This paper describes our efforts preparing NERSC users for KNL through the NERSC Exascale Science Application Program, Web documentation, and user training. We discuss how we configured the Cori system for usability and productivity, addressing programming concerns, batch system configurations, and default KNL cluster and memory modes. Here, system usage data, job completion analysis, programming and running jobs issues, and a few successful user stories on KNL are presented.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2019

Advances in plasma–wall interaction control for H-mode operation over 100 s with ITER-like tungsten divertor on EAST

A total power injection up to 0.3 GJ has been achieved in EAST long pulse H-mode operation of 101.2 s with an ITER-like water-cooled tungsten (W) mono-block divertor, which has steady-state power exhaust capability of 10 MWm –2 . The peak temperature of W target saturated at 12 s to the value T ~ 500 °C with a heat flux ~3.3 MW m –2 being maintained during the discharge. By tailoring the 3D divertor plasma footprint through edge magnetic topology change, the heat load was broadly dispersed and thus peak heat flux and W sputtering were well controlled. Active feedback control of H-mode detachment with D 2 fuelling or divertor impurity seeding has been achieved successfully, with excellent compatibility with the core plasma performance. Active feedback control of radiative power utilizing neon seeding was achieved with f rad = 18%–41% in H-mode operation, exhibiting potential for heat flux reduction with divertor and edge radiation. This has been further demonstrated in DIII-D high β P H-mode scenario within the joint DIII-D/EAST experiment using impurity seeding from the divertor volume. Steady-state particle control and impurity exhaust has been achieved for long pulse H-mode operation over 100 s with the W divertor by leveraging the effect of drifts and optimized divertor configuration, coupled with strong pumping and extensive wall conditioning. Methods toward the reduction of divertor W sourcing, which is of crucial importance for a metal-wall tokamak, are also explored. These advances provide vital experimental information on favourable core-edge integration for high power, long-pulse H-mode operation in EAST, ITER and CFETR.

43 PARTICLE ACCELERATORS↗