Search NASA⌕ Search

SEARCH · Search NASA

Results for “height function”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

ISEE-3 measurements of solar energetic particle composition

Preliminary observations of energetic particles from solar flares beginning on September 23 and November 10, 1978 are reported. The measurements were made from the ISEE-3 spacecraft using very thin, large area solid-state detectors. Charge composition was measured for all elements from Z = 2 to Z = 26 above approximately 2 MeV/nucleon. More than 100,000 nuclei with Z greater than 2 were pulse-height analyzed during the course of the first event, while the second was substantially smaller. These good statistics enable the observation of variations in composition at low energies as a function of time. For example, the Fe/O ratio (2.0-3.1 MeV/n) was observed in the September event to decrease by a factor of approximately 5. By contrast, this same ratio increased by a factor of approximately 1.5 during the November 10 event. Similar variations have been reported earlier by Scholer et al. (1978). These authors, however were unable to observe the He/O ratio which has now been observed also to show significant variation.

Von Rosenvinge, T. T.↗
NASA NTRS1987

Light scattering in cometary dust comae

Single and multiple scattering calculations were performed for a spherically symmetric cometary atmosphere irradiated by a plane parallel source. It is suggested that the increased flux found for anisotropic phase functions is due to the effect of directional scattering in the forward sun-comet axis. The isotropic multiply scattered flux at the surface is shown to be an increasing function of the opacity (tau) for tau of less than about 2.5. At large tau values, the maximum in the downward directed scattered flux still increases, but occurs at a height of several radii above the nucleus, resulting in a reduction at the surface. Results suggest that, except in the vicinity of the sun-comet axis, the plane parallel geometry tends to underestimate the degree of scattering.

Herman, Gary↗
NASA NTRS1998

3D-Stereoscopic Analysis of Solar Active Region Loops: I: SoHo/EIT Observations at Temperatures of 1.0-1.5 MK

The three-dimensional (3D) structure of solar active region NOAA 7986 observed on 1996 August 30 with the Extrem-ultraviolet Imaging Telescope (EIT) onboard the Solar and Heliospheric Observatory (SoHO) is analyzed. We develop a new method of Dynamic Stereoscopy to reconstruct the 3D geometry of dynamically changing loops, which allows us to determine the orientation of the loop plane with respect to the line-of-sight, a prerequisite to correct properly for projection effects in 3D loop models. With this method and the filter-ratio technique applied to EIT 171 A and 195 A images we determine the 3D coordinates (x(s), y(s), z(s)), the loop width) w(s), the electron density n(sub e)(s), and the electron temperature T(sub e)(s) as function of the loop length s for 30 loop segments. Fitting the loop densities with an exponential density model n(sub e)(h) we find that the so inferred scale height temperatures, T(sub e)(sup lambda) = 1.22 +/- 0.23 MK, match closely the EIT filter-ratio temperatures, T(sub e)(sup FIT) = 1.21 +/- 0.06 MK. We conclude that these rather large-scale loops (with heights of h approx. equals 50 - 200 Mm) that dominate EIT 171 A images are close to thermal equilibrium. Most of the loops show no significant thickness variation w(s), but many exhibit a trend of increasing temperature (dT/ds greater than 0) above the footpoint.

Aschwanden, Markus J.↗
NASA NTRS1999

Corona Structure and Heating Constraints Determined from SERTS Observations

Intensities of the Extreme-ultraviolet (EUV) spectral lines were measured as a function of radius off the solar limb by two flights of the Goddard's Solar Extreme-ultraviolet Rocket Telescope and Spectrograph (SERTS) for three quiet sun regions. Density scale heights were determined for the different spectral lines. Limits on the filling factor were determined. In the one case where an upper limit was determined it was much less than unity. Coronal heating above 1.15 solar radii is required for all three regions studied. For reasonable filling factors, local heating is needed.

Falconer, D. A.↗
NASA NTRS2003

Shock Formation and Energy Dissipation of Slow Magnetosonic Waves in Coronal Plumes

We study the shock formation and energy dissipation of slow magnetosonic waves in coronal plumes. The wave parameters and the spreading function of the plumes as well as the base magnetic field strength are given by empirical constraints mostly from SOHO/UVCS. Our models show that shock formation occurs at low coronal heights, i.e., within 1.3 bun, depending on the model parameters. In addition, following analytical estimates, we show that scale height of energy dissipation by the shocks ranges between 0.15 and 0.45 Rsun. This implies that shock heating by slow magnetosonic waves is relevant at most heights, even though this type of waves is apparently not a solely operating energy supply mechanism.

Cuntz, M.↗
NASA NTRS2011

Coronal Plumes in the Fast Solar Wind

The expansion of a coronal hole filled with a discrete number of higher density coronal plumes is simulated using a time-dependent two-dimensional code. A solar wind model including an exponential coronal heating function and a flux of Alfven waves propagating both inside and outside the structures is taken as a basic state. Different plasma plume profiles are obtained by using different scale heights for the heating rates. Remote sensing and solar wind in situ observations are used to constrain the parameter range of the study. Time dependence due to plume ignition and disappearance is also discussed. Velocity differences of the order of approximately 50 km/s, such as those found in microstreams in the high-speed solar wind, may be easily explained by slightly different heat deposition profiles in different plumes. Statistical pressure balance in the fast wind data may be masked by the large variety of body and surface waves which the higher density filaments may carry, so the absence of pressure balance in the microstreams should not rule out their interpretation as the extension of coronal plumes into interplanetary space. Mixing of plume-interplume material via the Kelvin-Helmholtz instability seems to be possible within the parameter ranges of the models defined here, only at large di stances from the Sun, beyond 0.2-0.3 AU. Plasma and composition measurements in the inner heliosphere, such as those which will become available with Solar Orbiter and Solar Probe Plus, should therefore definitely be able to identify plume remnants in the solar wind.

Velli, Marco↗
NASA NTRS2015

Remote Sensing of Cloud Top Heights Using the Research Scanning Polarimeter

Clouds cover roughly two thirds of the globe and act as an important regulator of Earth's radiation budget. Of these, multilayered clouds occur about half of the time and are predominantly two-layered. Changes in cloud top height (CTH) have been predicted by models to have a globally averaged positive feedback, however observational changes in CTH have shown uncertain results. Additional CTH observations are necessary to better and quantify the effect. Improved CTH observations will also allow for improved sub-grid parameterizations in large-scale models and accurate CTH information is important when studying variations in freezing point and cloud microphysics. NASA's airborne Research Scanning Polarimeter (RSP) is able to measure cloud top height using a novel multi-angular contrast approach. RSP scans along the aircraft track and obtains measurements at 152 viewing angles at any aircraft location. The approach presented here aggregates measurements from multiple scans to a single location at cloud altitude using a correlation function designed to identify the location-distinct features in each scan. During NASAs SEAC4RS air campaign, the RSP was mounted on the ER-2 aircraft along with the Cloud Physics Lidar (CPL), which made simultaneous measurements of CTH. The RSPs unique method of determining CTH is presented. The capabilities of using single and combinations of channels within the approach are investigated. A detailed comparison of RSP retrieved CTHs with those of CPL reveal the accuracy of the approach. Results indicate a strong ability for the RSP to accurately identify cloud heights. Interestingly, the analysis reveals an ability for the approach to identify multiple cloud layers in a single scene and estimate the CTH of each layer. Capabilities and limitations of identifying single and multiple cloud layers heights are explored. Special focus is given to sources of error in the method including optically thin clouds, physically thick clouds, multi-layered clouds as well as cloud phase. When determining multi-layered CTHs, limits on the upper clouds opacity are assessed.

Cloud height indicators↗
NASA NTRS1989

Turbulent small-scale neutral and ion density fluctuations as measured during MAC/Epsilon

During the MAC/Epsilon campaign (Fall 1987, from Andoya, Northern Norway, 69 N, 16 E) a total of four altitude profiles of neutral gas number densities and six profiles of ion number densities were measured with high spatial resolution in the height range from 60 to 120 km. First results of these rocket-borne experiments are presented with emphasis on small scale turbulent density variations and related turbulent parameter as structure function constants and energy dissipation rates.

Luebken, F.-J.↗
NASA NTRS1991

Lidar measurements at Garmisch, conversion model, and midlatitude aerosol effects

Lidar backscatter soundings of stratospheric aerosol layer were routinely made at the IFU, Garmisch-Partenkirchen. After 1979 significant perturbations of the stratosphere were observed after volcano eruptions from 1980 to 1985. A volcanically quiescent period followed until the eruption at the end of 1989. Determinations of particle extinction, mass and surface area of the stratospheric particulate load are important in climatic considerations and heterogeneous chemistry effects. Balloon-borne particle counter measurements are used to derive height and time resolved conversion factors to convert lidar backscatter data to extinction, mass and surface area values. This is done by combining particle size distributions with Mie backscatter and extinction functions. These conversion factors are applicable to midlatitude lidar observations and were used to convert ruby lidar measurement at the IFU.

Jaeger, Horst↗
NASA NTRS1991

A tidal wind model for 85-120 km based on CIRA-86 - A feasibility study

The feasibility of deriving a climatology of the diurnal variations of the wind in the 85-120 km region from the tidal components of density, temperature and composition contained in the new COSPAR CIRA-86 is examined. The CIRA density and temperature model is employed to derive the eastward and northward pressure gradient forces that serve as the forcing functions in the coupled momentum equations. At midlatitudes, the model shows some of the general features observed in the radar tidal data, e.g., the dominant semidiurnal tide with increasing amplitude with height and clockwise (counterclockwise) rotation of the velocity vector seen in the Northern (Southern) Hemisphere.

Fleming, E. L.↗
NASA NTRS2001

Huge Coronal Structure and Heating Constraints Determined from Serts Observations

Intensities of the extreme-ultraviolet (EUV) spectral lines were measured as a function of radius off the solar limb by two flights of the Goddard's Solar Extreme-Ultraviolet Rocket Telescope and Spectrograph (SERTS) for three quiet-Sun regions. Density scale heights were determined for the different spectral lines. Limits on the filling factor were determined. In the one case where an upper limit was determined it was much less than unity. coronal heating above 1.15 solar radii is required for all three regions studied. For reasonable filling factors, local heating is needed.

Falconer, D. A.↗
NASA NTRS2019

Surrogate Modeling and Optimization of a Combustor with an Interdigitated Flushwall Injector

Design and Analysis of Computer Experiments (DACE) methods are applied and used to perform surrogate modeling and optimization of a simplified combustor flowpath with an interdigitated flushwall injector. The objectives of the optimization are the thrust potential and combustion efficiency, which are evaluated across a range of flight Mach numbers, duct heights, spanwise spacings, and injection angles. The focus of this work is to highlight the application of a sequential learning approach, in order to learn about the responses of the objective functions over the design space and to identify local regions of interest for further analysis. This approach is contrasted to a previous effort where only a single sampling set was used to fit surrogate models and perform optimization. The optimal solutions resulting from the previous and present approaches are different, due to surrogate model-guided local refinement of the design space allowed by the sequential learning method. The values of the global error estimates between the previous and present approaches are comparable, but the sequential method proved more computationally cost-effective. Further refinement in the optimal regions might be needed to improve predictive capability of surrogate models and to obtain the optimal solutions sets.

Rajiv R Shenoy↗
NASA NTRS2023

Turbulence Model Validation Through Joint Experimental /Computational Studies of Separated Flow Over A Three-Dimensional Tapered Bump: Part I - Experimental Investigation

The results of a three-year experimental campaign aimed at comprehensively documenting the separated flow over a three-dimensional bump are presented with the purpose of generating a benchmark experimental database useful in validating computational fluid dynamics (CFD) flow simulations. The bump model geometry was designed to provide well-defined and repeatable smooth-body flow separation conditions that were suitable for both experiments and simulations. The bump had a Gaussian streamwise profile with a constant height equal to 8.5% of its width over the central 60% of the test section width. The remaining 40% were outboard spanwise portions that gradually taper to zero using an error function profile to minimize side-wall boundary layer effects. The model was immersed in a turbulent boundary layer that was developed on a suspended flat plate in the Notre Dame Mach 0.6 Wind Tunnel. In order to document the effect of the incoming boundary layer thickness on the flow separation, the bump model could be located at two streamwise positions. The mean velocity and turbulence intensity of the wind tunnel freestream flow field and approaching turbulent boundary layer were fully documented. The measurements of the flow separation region included surface visualization, wall shear stress using oil-film interferometry, mean and dynamic surface pressure, and planar and stereoscopic particle image velocimetry. The experiments were conducted over a range of Mach numbers from 0.05 to 0.2 corresponding to a range of Reynolds numbers based on the test section spanwise dimension (0.914m) of 1.0 × 10 6 ≤ Re L = U ∞ L/ν ≤ 4.0 × 10 6 . The bulk of the results are presented for the higher Mach number conditions of 0.1 and 0.2 with Re L = 2.0 × 10 6 and 4.0 × 10 6 , respectively. Extensive uncertainty analysis of the data was performed. The data is archived in the NASA Langley Turbulence Modeling Resource website at https://turbmodels.larc.nasa.gov/Other_exp_Data/speedbump_sep_exp.html. In addition to the experiments, a computational effort was made in parallel by the CFD group at Boeing Research & Technology highlighting the usefulness of the data set, which is outlined in the accompanying CFD report.

Flow separation↗
DOE OSTI2025

Revealing the Origin and Nature of the Buried Metal‐Substrate Interface Layer in Ta/Sapphire Superconducting Films

Abstract Despite constituting a smaller fraction of the qubit's electromagnetic mode, surfaces and interfaces can exert significant influence as sources of high‐loss tangents, which brings forward the need to reveal properties of these extended defects and identify routes to their control. Here, we examine the structure and composition of the metal‐substrate interfacial layer that exists in Ta/sapphire‐based superconducting films. Synchrotron‐based X‐ray reflectivity measurements of Ta films, commonly used in these qubits, reveal an unexplored interface layer at the metal‐substrate interface. Scanning transmission electron microscopy and core‐level electron energy loss spectroscopy identified an intermixing layer (≈0.65 ± 0.05 nm) at the metal‐substrate interface containing Al, O, and Ta atoms. Density functional theory modeling reveals that the structure and properties of the Ta/sapphire heterojunctions are determined by the oxygen content on the sapphire surface prior to Ta deposition for two atomic terminations of sapphire. Using a multimodal approach, we gained deeper insights into the interface layer between the metal and substrate, which suggests that the orientation of deposited Ta films depend on the surface termination of sapphire. The observed elemental intermixing at the metal‐substrate interface influences the thermodynamic stability and electronic behavior of the film, which may also affect qubit performance.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Cross correlation and length scales in turbulent flows near surfaces

Two kinds of length scales are used in turbulent flows; 'functional length scales' such as mixing length, dissipation length L(sub epsilon), etc., and 'flow-field length scales' derived from cross correlations of velocity, pressure, etc. in the flow. Some connection between these scales are derived here. We first consider the cross correlation R(sub vv)(y,y(sub 1)) of the normal components u at two heights y, y(sub 1) above a rigid surface, normalized by the velocity y(sub 1) (greater than y). For shear-free boundary layers it is found theoretically, and in field and numerical experiments that R(sub vv) approximately equals y/y(sub 1). For shear layers it is also found that R(sub vv) approximately equals f(y/y(sub 1)) less than or equal to y,y(sub 1). This function f differs slightly between low Reynolds number numerical simulations and field experiments. The lateral structure defined by R(sub vv)(y,r(sub 3); y(sub 1),0) is also self similar and shows that the eddies centered at about y(sub 1) appear to have constant lateral width a(sub 3) above and below y(sub 1), where a(sub 3, sup +) approximately equals 7+1/(1.4dU(sup +)/dy(sup +)), when normalized on u(sub *) and v, where U is the mean velocity. Results for L(sub epsilon, sup -1) from direct numerical simulation are found to compare well with the formula L(sub epsilon, sup -1) = A(sub B)/y + A(sub S)dU/dy/v, for unidirectional and reversing turbulent boundary layers and channel flow, except near where dU/dy approximately equals 0. The conclusion is that the large-scale eddy structure and length scales in these flows are determined by a combination of shear and blocking, and that the vertical component of turbulence has a self-similar structure in both kinds of boundary layer.

Hunt, J. C. R.↗
NASA NTRS1994

Implications for gravitational lensing and the dark matter content in clusters of galaxies from spatially resolved x-ray spectra

A simple method for deriving well-behaved temperature solutions to the equation of hydrostatic equilibrium for intracluster media with X-ray imaging observations is presented and applied to a series of generalized models as well as to observations of the Perseus cluster and Abell 2256. In these applications the allowed range in the ratio of nonbaryons to baryons as a function of radius is derived, taking into account the uncertainties and crude spatial resolution of the X-ray spectra and considering a range of physically reasonable mass models with various scale heights. Particular attention is paid to the central regions of the cluster, and it is found that the dark matter can be sufficiently concentrated to be consistent with the high central mass surface densities for moderate-redshift clusters from their gravitational lensing properties.

Loewenstein, M.↗
NASA NTRS1997

SYNTHESIS OF NOVEL ALL-DIELECTRIC GRATING FILTERS USING GENETIC ALGORITHMS

We are concerned with the design of inhomogeneous, all dielectric (lossless) periodic structures which act as filters. Dielectric filters made as stacks of inhomogeneous gratings and layers of materials are being used in optical technology, but are not common at microwave frequencies. The problem is then finding the periodic cell's geometric configuration and permittivity values which correspond to a specified reflectivity/transmittivity response as a function of frequency/illumination angle. This type of design can be thought of as an inverse-source problem, since it entails finding a distribution of sources which produce fields (or quantities derived from them) of given characteristics. Electromagnetic sources (electric and magnetic current densities) in a volume are related to the outside fields by a well known linear integral equation. Additionally, the sources are related to the fields inside the volume by a constitutive equation, involving the material properties. Then, the relationship linking the fields outside the source region to those inside is non-linear, in terms of material properties such as permittivity, permeability and conductivity. The solution of the non-linear inverse problem is cast here as a combination of two linear steps, by explicitly introducing the electromagnetic sources in the computational volume as a set of unknowns in addition to the material unknowns. This allows to solve for material parameters and related electric fields in the source volume which are consistent with Maxwell's equations. Solutions are obtained iteratively by decoupling the two steps. First, we invert for the permittivity only in the minimization of a cost function and second, given the materials, we find the corresponding electric fields through direct solution of the integral equation in the source volume. The sources thus computed are used to generate the far fields and the synthesized triter response. The cost function is obtained by calculating the deviation between the synthesized value of reflectivity/transmittivity and the desired one. Solution geometries for the periodic cell are sought as gratings (ensembles of columns of different heights and widths), or combinations of homogeneous layers of different dielectric materials and gratings. Hence the explicit unknowns of the inversion step are the material permittivities and the relative boundaries separating homogeneous parcels of the periodic cell.

Zuffada, Cinzia↗
DOE OSTI2021

Boundary zonal flows in rapidly rotating turbulent thermal convection

Recently, in Zhang et al. ( Phys. Rev. Lett. , vol. 124, 2020, 084505), it was found that, in rapidly rotating turbulent Rayleigh–Bénard convection in slender cylindrical containers (with diameter-to-height aspect ratio $\varGamma =1/2$ ) filled with a small-Prandtl-number fluid ( ${Pr}\approx 0.8$ ), the large-scale circulation is suppressed and a boundary zonal flow (BZF) develops near the sidewall, characterized by a bimodal probability density function of the temperature, cyclonic fluid motion and anticyclonic drift of the flow pattern (with respect to the rotating frame). This BZF carries a disproportionate amount ( ${>}60\,\%$ ) of the total heat transport for ${Pr} < 1$ , but decreases rather abruptly for larger ${Pr}$ to approximately $35\,\%$ . In this work, we show that the BZF is robust and appears in rapidly rotating turbulent Rayleigh–Bénard convection in containers of different $\varGamma$ and over a broad range of ${Pr}$ and ${Ra}$ . Furthermore, tirect numerical simulations for Prandtl number $0.1 \leq {\textit {Pr}} \leq 12.3$ , Rayleigh number $10^7 \leq {Ra} \leq 5\times 10^{9}$ , inverse Ekman number $10^{5} \leq 1/{\textit {Ek}} \leq 10^{7}$ and $\varGamma = 1/3$ , 1/2, 3/4, 1 and 2 show that the BZF width $\delta _0$ scales with the Rayleigh number ${Ra}$ and Ekman number ${\textit {Ek}}$ as $\delta _0/H \sim \varGamma ^{0} Pr^{\{-1/4, 0\}} {Ra}^{1/4} {\textit {Ek}}^{2/3}$ ( $\{{\textit {Pr}}<1, {\textit {Pr}}>1\}$ ) and with the drift frequency scales as $\omega /\varOmega \sim \varGamma ^{0} Pr^{-4/3} {Ra}\,{\textit {Ek}}^{5/3}$ , where $H$ is the cell height and $\varOmega$ the angular rotation rate. The mode number of the BZF is 1 for $\varGamma \lesssim 1$ and $2 \varGamma$ for $\varGamma = \{1,2\}$ independent of ${Ra}$ and ${Pr}$ . The BZF is quite reminiscent of wall mode states in rotating convection.

42 ENGINEERING↗