Search NASA⌕ Search

SEARCH · Search NASA

Results for “parameter reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

A method for the measurement and analysis of ride vibrations of transportation systems

The measurement and recording of ride vibrations which affect passenger comfort in transportation systems and the subsequent data-reduction methods necessary for interpreting the data present exceptional instrumentation requirements and necessitate the use of computers for specialized analysis techniques. A method is presented for both measuring and analyzing ride vibrations of the type encountered in ground and air transportation systems. A portable system for measuring and recording low-frequency, low-amplitude accelerations and specialized data-reduction procedures are described. Sample vibration measurements in the form of statistical parameters representative of typical transportation systems are also presented to demonstrate the utility of the techniques.

Catherines, J. J.↗

Real time telemetry and data compression

The generation of telemetry and data compression by the flight program was verified. The adequacy of flight program telemetry control and timing is proven by the analysis of simulation laboratory runs of past programs through the use of telemetry. The telemetry data are correctly issued using specific tags called process input/output (P10) tags. Verification is accomplished by ensuring that a specific P10 tag and mode register setting identifies the correct parameter and that the data are properly scaled for subsequent ground station reduction. It was checked that the LVDC telemetry correctly adheres to the general requirements specified by the EDD. Data compression specifications are verified using compressed data from nominal flight simulations and from a series of perturbations designed to test data table overflows, data dump rates, and compression of data for occurrence events.

Source record↗

A statistical study of the upstream wave boundary outside the earth's bow shock

The location of the forward boundary of the upstream wave region ahead of the earth's bow shock is investigated statistically using plasma and magnetic-field data obtained by Heos 1. The analysis is conducted on the assumption that the waves are produced by protons reflected from the bow shock and traveling upstream with an effective velocity equal to the product of a parameter, p, and the solar-wind bulk velocity. The data-reduction methods are summarized, and uncertainties in the determination of the value of p are discussed. It is found that the overall average boundary corresponds to a velocity of approximately twice the solar-wind velocity for protons reflected from the daytime sector of the bow shock. More refined analysis of the data shows that the value of p is approximately 1.6 near the subsolar point and greater than 2 along the daytime flanks of the bow shock.

Diodato, L.↗

Turbulent flow in a channel with a wall with progressive waves

The effects of prescribed wall motion on turbulent channel flow were examined with the objective of understanding the drag mechanisms and obtaining a possible means for drag reduction. A computer program for large-eddy simulation (LES) of turbulent flow in a channel was adapted to treat the case of time-varying wall motion using linearized boundary conditions. The code was applied to flow in a channel with prescribed wall motion on one wall. It was found that the results can be explained by a model based on a Stokes-like layer near the moving wall. This provides a theory which can be used to guide the selection of parameters. Considering both viscous and pressure drag components, it was found that net drag reduction is possible under certain conditions of wall motion. However, the work required to drive the wall motion can be greater than the reduced through-flow energy requirement. The major effects of the wall motion are restricted to the viscous sublayer of the turbulent flow.

Kuhn, G. D.↗

Precision X-band Doppler and ranging navigation for current and future Mars exploration missions

This paper describes a navigation error covariance analysis of two scenarios derived from the Mars Observer mission and the planned Mars Environmental SURvey (MESUR) Pathfinder mission, respectively. The analysis was performed to establish the potential navigational performance of the X-band tracking system in NASA's Deep Space Network, and to evaluate the sensitivity of the predicted performance to variations in the quantity of data acquired, the ground system error modeling assumptions, and data reduction schemes. The simulated data arcs used in the analysis are representative of the actual data arcs that will be used to predict the aim point for the Mars orbit insertion maneuver, in the case of Mars Observer, and the interplanetary trajectory aim point corresponding to the target Mars landing site in the case of MESUR Pathfinder. The results indicate that with a suitable sequential data reduction scheme and accurate calibrations of instrumentation, transmission media, and platform model parameters, navigation accuracies of 5 to 15 km (1 sigma) can be achieved, equivalent to 15 to 40 nrad in geocentric angle uncertainty.

Estefan, Jeffrey A.↗

The NASA landing gear test airplane

A tire and landing gear test facility has been developed and incorporated into a Convair 990 aircraft. The system can simulate tire vertical load profiles to 250,000 lb, sideslip angles to 15 degrees, and wheel braking on actual runways. Onboard computers control the preprogrammed test profiles through a feedback loop and also record three axis loads, tire slip angle, and tire condition. The aircraft to date has provided tire force and wear data for the Shuttle Orbiter tire on three different runways and at east and west coast landing sites. This report discusses the role of this facility in complementing existing ground tire and landing gear test facilities, and how this facility can simultaneously simulate the vertical load, tire slip, velocity, and surface for an entire aircraft landing. A description is given of the aircraft as well as the test system. An example of a typical test sequence is presented. Data collection and reduction from this facility are discussed, as well as accuracies of calculated parameters. Validation of the facility through ground and flight tests is presented. Tests to date have shown that this facility can operate at remote sites and gather complete data sets of load, slip, and velocity on actual runway surfaces. The ground and flight tests have led to a successful validation of this test facility.

Carter, John F.↗

Mathematical Analysis of Space Radiator Segmenting for Increased Reliability and Reduced Mass

Spacecraft for long duration deep space missions will need to be designed to survive micrometeoroid bombardment of their surfaces some of which may actually be punctured. To avoid loss of the entire mission the damage due to such punctures must be limited to small, localized areas. This is especially true for power system radiators, which necessarily feature large surface areas to reject heat at relatively low temperature to the space environment by thermal radiation. It may be intuitively obvious that if a space radiator is composed of a large number of independently operating segments, such as heat pipes, a random micrometeoroid puncture will result only in the loss of the punctured segment, and not the entire radiator. Due to the redundancy achieved by independently operating segments, the wall thickness and consequently the weight of such segments can be drastically reduced. Probability theory is used to estimate the magnitude of such weight reductions as the number of segments is increased. An analysis of relevant parameter values required for minimum mass segmented radiators is also included.

Juhasz, Albert J.↗

Methods of Constructing a Blended Performance Function Suitable for Formation Flight

Two methods for constructing performance functions for formation fight-for-drag-reduction suitable for use with an extreme-seeking control system are presented. The first method approximates an a prior measured or estimated drag-reduction performance function by combining real-time measurements of readily available parameters. The parameters are combined with weightings determined from a minimum squares optimization to form a blended performance function.

control systems↗

Estimating the Effects of Module Area on Thin-Film Photovoltaic System Costs: Preprint

We investigate the potential effects of module area on the cost and performance of photovoltaic systems. Applying a bottom-up methodology, we analyzed the costs associated with thin-film modules and systems as a function of module area. We calculate a potential for savings of up to 0.10 dollars/W and 0.13 dollars/W in module manufacturing costs for CdTe and CIGS respectively, with large area modules. We also find that an additional 0.04 dollars/W savings in balance-of-systems costs may be achieved. Sensitivity of the dollar/W cost savings to module efficiency, manufacturing yield, and other parameters is presented. Lifetime energy yield must also be maintained to realize reductions in the levelized cost of energy; the effects of module size on energy yield for monolithic thin-film modules are not yet well understood. Finally, we discuss possible non-cost barriers to adoption of large area modules.

14 SOLAR ENERGY↗

Additive Manufacturing: A New Paradigm for the Next Generation of High-Power-Density Direct-Drive Electric Generators: Preprint

In recent years, there has been a growing demand for high-power-density direct-drive generators in the wind industry owing to their high reliability, torque per-unit volume, and conversion efficiencies. However, direct-drive wind turbine generators are very large, low-speed electric machines, which pose remarkable design and manufacturing issues that challenge their upscaling potential and cost of implementation. With air-gap tolerance as the main design driver, the need for high stiffness shifts the focus toward support-structure design that forms a significant portion of the generator's total mass. Existing manufacturing processes allow the use of segmented-steel-weldment disk or spoke-arm assemblies that yield stiffer structures per unit mass but tend to be heavier and more expensive to build. As a result, there is a need for a transformative approach to realize lightweight designs that can also facilitate series production at competitive costs. Inspired by recent developments in metal additive manufacturing (AM), we explore a new freedom in the structural design space with a high potential for weight savings in direct-drive generators. This includes the feasibility of using nonconventional complex geometries, such as lattice-based structures as structurally efficient options. Powder-binder jetting of a sand-cast mold was identified as the most feasible AM technology to produce large-scale generator rotor structures with complex geometry. A parametric optimization study was performed and optimized results within deformation and mass constraints were found for each design. The response to the maximum Maxwell stress due to unbalanced magnetic pull was also explored for each design. Further, a topology optimization was applied for each parameter-optimized design to validate results and provide insights into further mass reduction. These novel designs catered for AM are compared in both deflection and mass to conventional rotor designs using NREL's systems engineering design tool, GeneratorSE. The optimized lattice design with a Ubeam truss resulted in a 24% reduction in structural mass of the rotor and 60% reduction in radial deflection. It is demonstrated that additive manufacturing shifts the focus from manufacturability constraints toward lower mass.

17 WIND ENERGY↗

Power System Network Reduction for Power Hardware-in-the-Loop Simulation: Preprint

This paper proposes a single-port equivalent and a two-port equivalent to respectively reduce single-port and two-port areas in a large power network. Parameters of the reduced systems are rigorously derived, which guarantees that the electrical quantities at the port remain unchanged over the reduction, including voltage magnitude and phase, active and reactive power injections into the area to be reduced. The proposed techniques are applied to reduce a practical Maui grid, where the total numbers of buses, lines and transformers are respectively reduced from 212, 106 and 108 to 45, 30 and 13. Dynamic behaviors between the full model and the reduced model are compared in detail to illustrate the efficacy and accuracy of the proposed network reduction.

41 EE - Solar Energy Technologies Office (EE-4S)↗

The MSFR as a flexible CR reactor: the viewpoint of safety

In this paper, the possibility has first been discussed of using the liquid-fuelled Molten Salt Fast Reactor (MSFR) as a flexible conversion ratio (CR) reactor without design modification. By tuning the reprocessing rate it is possible to determine the content of fission products in the core, which in turn can significantly affect the neutron economy without incurring in solubility problems. The MSFR can thus be operated as U-233 breeder (CR>1), iso-breeder (CR=1) and burner reactor (CR<1). In particular a 40 year doubling time can be achieved, as well as a considerable Transuranics and MA (minor actinide) burning rate equal to about 150 kg{sub HN}/GWE-yr. The safety parameters of the MSFR have then been evaluated for different fuel cycle strategies. Th use and a softer spectrum combine to give a strong Doppler coefficient, one order of magnitude higher compared to traditional fast reactors (FRs). The fuel expansion coefficient is comparable to the Doppler coefficient and is only mildly affected by core compositions, thus assisting the fuel cycle flexibility of the MSFR. βeff and generation time are comparable to the case of traditional FRs, if a static fuel is assumed. A notable reduction of βeff is caused by salt circulation, but a low value of this parameter is a limited concern in the MSFR thanks to the lack of a burnup reactivity swing and of positive feedbacks. A simple approach has also been developed to evaluate the MSFR capabilities to withstand all typical double-fault accidents, for different fuel cycle options.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Influence of Na and Ca Concentrations on Sr Adsorption Performance of Cs-Sr Simultaneous Adsorbent - 19315

Treating evaporation-concentrated liquid waste stored in tanks at Fukushima Daiichi Nuclear Power Station site with high radioactive Cs and Sr concentrations has been examined using Cs-Sr simultaneous adsorbent. The evaporation-concentrated liquid waste contains Na and Ca concentrations which are almost equal to or higher than their natural concentrations in seawater. In the Cs-Sr simultaneous adsorbent, Na and Ca compete with Sr adsorption. For the aforementioned reasons, the influence of Na and Ca concentrations on Sr adsorption performance of Cs-Sr simultaneous adsorbent was experimentally evaluated. The throughput of Sr adsorption was measured by column test in which Na and Ca concentrations were set as parameters. The results showed that higher concentrations of Na and Ca caused reduction of throughput of Sr adsorbent, and Ca concentration that showed a certain throughput was two or more orders of magnitude lower than Na concentration. This result reflected the selectivity of Cs-Sr simultaneous adsorbent was higher in the order of Sr > Ca > Na. Based on the results, treatment process of evaporation-concentrated liquid waste that consisted of dilution by water and then removal of Sr using Cs-Sr simultaneous adsorbent was investigated. The results suggested that the dilution of the evaporation-concentrated liquid waste improve the throughput of the Cs-Sr simultaneous adsorbent and leads to the reduction of the amount of Cs-Sr simultaneous adsorbent needed to treat the evaporation-concentrated liquid waste. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Local structure of solid Rb at megabar pressures

We have investigated the local and electronic structure of solid rubidium by means of x-ray absorption spectroscopy up to 101.0 GPa, thus doubling the maximum investigated experimental pressure. This study confirms the predicted stability of phase VI and was completed by the combination of two pivotal instrumental solutions. On one side, we made use of nanocrystalline diamond anvils, which, contrary to the more commonly used single crystal diamond anvils, do not generate sharp Bragg peaks (glitches) at specific energies that spoil the weak fine structure oscillations in the x-ray absorption cross section. Second, we exploited the performance of a state-of-the-art x-ray focussing device yielding a beam spot size of 5 × 5 μm{sup 2}, spatially stable over the entire energy scan. An advanced data analysis protocol was implemented to extract the pressure dependence of the structural parameters in phase VI of solid Rb from 51.2 GPa up to the highest pressure. A continuous reduction of the nearest neighbour distances was observed, reaching about 6% over the probed pressure range. We also discuss a phenomenological model based on the Einstein approximation to describe the pressure behaviour of the mean-square relative displacement. Within this simplified scheme, we estimate the Grüneisen parameter for this high pressure Rb phase to be in the 1.3–1.5 interval.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Divertor plasma detachment: roles of plasma momentum, energy, and particle balances

Abstract Contrary to statements from some recent papers, the bifurcation of the scrape-off layer and divertor plasma parameters, as described within a 1D model, does exist. The analysis of both numerical simulations and experimental data shows that the real physical reasons that can cause a strong reduction of the plasma particle flux to the target j d are impurity radiation loss and volumetric plasma recombination. Fitting the parameter describing the ‘plasma momentum removal’, based on the results of 2D numerical simulations, then using this fit in subsequent analytic expressions for j d , and finally interpreting the evolution of j d as the result of elastic plasma-neutral interactions break the causality principle and lead to a wrong physical picture of divertor plasma detachment.

Physics↗

Chromium (VI) reduction in acetate- and molasses-amended natural media: empirical model development

Stimulating indigenous microbes to reduce heavy metals from highly toxic oxidized species to more benign reduced species is a promising groundwater remediation technique that has already seen successful field applications. Designing such a bio-remediation scheme requires a model incorporating the kinetics of nonlinear bio-geochemical interactions between multiple species. With this motivation, we performed a set of microcosm experiments in natural sediments and their indigenous pore water and microbes, generating simultaneous time series for concentrations of Cr(VI), an electron donor (both molasses and acetate were considered), and biomass. Molasses was found to undergo a rapid direct abiotic reaction which eliminated all Cr(VI) before any biomass had time to grow. This was not found in the acetate microcosms, and a distinct zero-order bio-reduction process was observed. Existing models were found inappropriate and a new set of three coupled governing equations representing these process dynamics were developed and their parameters calibrated against the time series from the acetate-amended microcosms. Cell suspension batch experiments were also performed to calibrate bio-reduction rates in the absence of electron donor and sediment. The donor used to initially grow the cells (molasses or acetate) was found not to impact the reduction rate constants in suspension, which were orders of magnitude larger than those explaining the natural media microcosm experiments. This suggests the limited utility of kinetics determined in suspension for remedial design. Scoping studies on the natural media microcosms were also performed, suggesting limited impact of foreign abiotic material and minimal effect of diffusion limitation in the vertical dimension. These analyses may be of independent value to future researchers.

54 ENVIRONMENTAL SCIENCES↗

Editorial: Selective Controls on Microbial Energy Metabolisms: From the Microscale to the Macroscale

A mechanistic and predictive understanding of the genotypic and phenotypic controls on microbial element cycling remains a grand challenge in microbiology. While the composition and concentration of carbon sources, electron donors, and electron acceptors are known to influence microbial community structure by selecting for microbial sub-populations with distinct catabolic and respiratory pathways, selective inhibitors and trace nutrient availability modulate the activity of metabolic enzymes. This in turn influences the distribution of microbial sub-populations with distinct metabolic and respiratory traits, which are then structured by complex multi-dimensional environmental gradients that influence the composition, gene content and element cycling activity of microbiomes. While some parameters are known to select for different respiratory activities (e.g., lanthanides as essential nutrients for methanotrophs, molybdate as a specific inhibitor of sulfate reduction, carbon:nitrogen ratio and concentration as a control on the end-products of nitrate respiration), there are others to discover, and demonstrating how selective parameters operate and mediate element cycling across scales requires multi-disciplinary research in both the lab and field.

59 BASIC BIOLOGICAL SCIENCES↗

Accelerating uncertainty quantification in incremental dynamic analysis using dimension reduction-based surrogate modeling

We propose a surrogate modeling framework based on dimension reduction to facilitate the quantification of seismic risk of structural systems in performance-based earthquake engineering. The framework adopts incremental dynamic analysis (IDA) for addressing hazard variability, and promotes significant computational efficiency improvement for propagating epistemic uncertainties associated with the structural models. It utilizes both linear and nonlinear dimension reduction approaches, equipped with inverse mappings, to learn a functional between the input parameter space (e.g., the epistemic uncertainties of the structure) to the high-dimensional output space created through the IDA implementation across different ground motions and seismic intensity levels. Polynomial chaos expansion is adopted as the surrogate model to learn this functional in the reduced space. A nine-story steel moment-resisting frame with uncertain structural properties is used as a testbed. Furthermore, we select the seismic fragility curves as a measure of the structure’s seismic performance, since it provides an estimate of the probability of entering specified damage states for given levels of ground shaking.

42 ENGINEERING↗