Search NASA⌕ Search

SEARCH · Search NASA

Results for “reverse engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

The Impact of Inverter Dead-Time in Single-Phase Wireless Power Transfer Systems

In this paper, the effect of the dead-time on a single-phase wireless power transfer system is studied in detail. In practice, the dead-time is always placed between the complementary switching pulses of the inverter phase-leg. At higher operating frequencies, the dead-time issues in the resonant inverter become critical, especially as the power level increases. The detailed analysis of the dead-time on a wireless power transfer system is discussed for different operating conditions of the inverter duty-cycle and power factor. The switching characteristics of the wireless power transfer system inverter are analyzed, and the notch phenomenon that appears at the output of the inverter is also discussed. A notch equation based on the observations is derived to predict the notch occurrence during the system operation. Furthermore, the mathematical expressions are presented for different notch conditions. Subsequently, the effect of the notches on the sensitivity and the power transfer of the series-series compensated wireless power transfer system is analyzed. Finally, the approach is verified experimentally on an 8 kW wireless power transfer system prototype, and the results are compared with the theoretical analysis.

42 ENGINEERING↗

Correlation of combustor acoustic power levels inferred from internal fluctuating pressure measurements

Combustion chamber acoustic power levels inferred from internal fluctuating pressure measurements are correlated with operating conditions and chamber geometries over a wide range. The variables include considerations of chamber design (can, annular, and reverse-flow annular) and size, number of fuel nozzles, burner staging and fuel split, airflow and heat release rates, and chamber inlet pressure and temperature levels. The correlated data include those obtained with combustion component development rigs as well as engines.

Vonglahn, U. H.↗

Correlation of combustor acoustic power levels inferred from internal fluctuating pressure measurements

Combustion chamber acoustic power levels inferred from internal fluctuating pressure measurements are correlated with operating conditions and chamber geometries over a wide range. The variables include considerations of chamber design (can, annular, and reverse-flow annular) and size, number of fuel nozzles, burner staging and fuel split, airflow and heat release rates, and chamber inlet pressure and temperature levels. The correlated data include those obtained with combustion component development rigs as well as engines.

Von Glahn, U. H.↗

Mechanical Backup For Fly-By-Wire Control System

Mechanical device eliminates need for redundant fly-by-wire subsystems. Main components are two linkages. One connected to control column in conventional, reversible control system. Other slides inside first linkage and connected to pilot's control wheel. In addition to aircraft applications, design used in control systems in which computer control desirable but safety backup systems required; for example, in boat rudders, engine controls in boats and automobiles, and controls in construction equipment.

Stewart, Eric C.↗

Coupled numerical simulation of the external and engine inlet flows for the F-18 at large incidence

This paper presents a numerical simulation of the external and engine inlet flows for the F-18 aircraft at typical high-angle-of-attack flight conditions. Two engine inlet mass flow rates, corresponding to flight idle and maximum power, were computed. This was accomplished using a structured, overset grid technique to couple the external and internal grid systems. Reynolds-averaged Navier-Stokes solutions were obtained using an implicit, finite-differencing scheme. Results show a strong coupling of the external and engine inlet flows, especially at the maximum power setting. Increasing the mass flow rate through the inlet caused the primary vortex breakdown location to move downstream. This trend is also observed in flight tests performed on the F-18. A reversed flow region upstream of the inlet duct is visible in the faired-inlet and flight-idle computations. This flow reversal is not present in the maximum power setting computation. These large-scale changes in flow structure highlight the importance of simulating inlet conditions in high-angle-of-attack aircraft computations.

Murman, Scott M.↗

Magellan Aerodynamic Characteristics During the Termination Experiment Including Thruster Plume-Free Stream Interaction

Results are presented on the aerodynamic characteristics of the Magellan spacecraft during the October 1994 Termination Experiment, including the effects of the thruster engine exhaust plumes upon the molecular free stream around the spacecraft and upon the aerodynamics coefficients. As Magellan passed through the Venusian atmosphere, the solar arrays were turned in opposite directions relative to the free stream creating a torque on the spacecraft. The spacecraft control system was programmed to counter the effects of this torque with attitude control engines to maintain an inertially fixed attitude. The orientation and reaction engine telemetry returned from Magellan are used to create a model of the aerodynamic torques. Geometric models of the Magellan spacecraft are analyzed with the aid of both free molecular and Direct Simulation Monte Carlo codes. The simulated aerodynamic torques determined are compared to the measured torques. The Direct Simulation Monte Carlo method is also used to model the attitude engine exhaust plumes, the free stream disturbance caused by these plumes, and the resulting torques acting on the spacecraft compared to no-exhaust plume cases. The effect of the exhaust plumes was found to be sufficiently large that thrust reversal is possible.

Cestero, Francisco J.↗

Boosting the activity of non-platinum group metal electrocatalyst for the reduction of oxygen via dual-ligated atomically dispersed precursors immobilized on carbon supports

This paper describes the use of both atomically dispersed precursors (ADPs) and conductive carbon dispersion towards the synthesis of iron-based single atom electrocatalysts for the oxygen reduction reaction (ORR). For non-platinum group metal (non-PGM) catalysts, single iron, cobalt or manganese atoms coordinated with nitrogen are the most active structures towards the ORR. Achieving a high density of active sites made of single atoms is still challenging, requiring careful controls of pyrolysis to reduce the sintering of metal active sites. Herewith, we present a new strategy to synthesize iron-based single atom ORR electrocatalysts using a two pronged approach. We first designed a dual-ligated metal organic framework (MOF) precursor. This MOF was then immobilized onto Ketjen black carbon that serves as a conductive dispersion medium for creating the highly dispersed single atom sites. In this work, we demonstrate a near complete dispersion of the iron sites without obvious formation of nanoparticles. The activity of the resulting electrocatalyst exhibited an onset potential of 0.96 V and a half-wave potential of 0.84 V vs. reversible hydrogen electrode (RHE).

42 ENGINEERING↗

Analysis of Diode Reverse Recovery Effect on ZVS Condition for GaN-Based LLC Resonant Converter

LLC resonant converter can achieve zero voltage switching (ZVS) for primary-side devices and zero current switching (ZCS) for secondary-side rectifiers. However, the reverse recovery and junction capacitance (C j ) of secondary-side diode critically affect the ZVS condition of primary-side switches. The effect of C j has been discussed in literature, but not the reverse recovery. In this paper, the reverse recovery charge (Q rr ) is converted to an equivalent capacitance (C rr_eq ) for the study of primary-side ZVS performance. An accurate model during deadtime is derived and further applied to characterize ZVS performance with different reverse recovery charges in different regions. The concept of establishing parameter C total to consider both C j and C rr_eq is proposed to evaluate the effect of the secondary-side rectifiers. This concept provides the guideline for diode and synchronous rectification MOSFET selection to ensure ZVS condition for LLC converters. To verify the concept and the derived model,a 200/400 V 400 W LLC resonant converter prototype operating from 200 to 700 kHz is built and its ZVS performances with different diodes are compared. Two issues caused by Q rr effect, including V ds reverse charging and asymmetrical waveform during deadtime, are explained thoroughly as well.

42 ENGINEERING↗

Measurements of Forward Flight Effects on the Advanced Ducted Propulsion Demonstrator Engine

The performance of the Pratt & Whitney Advanced Ducted Propulsion (ADP) UHB concept has been recently evaluated with studies of a 17 in. diameter fan simulator. Following the model scale tests, a 118 in. diameter demonstrator was tested at the NASA Ames 40- by 80-Foot Wind Tunnel. The 18 blade fan was driven by the low compressor shaft of a PW2037 core through a reduction gear system fabricated by Fiat with approximately 1:3.7 reduction ratio. ne variable pitch fan was hydraulically actuated with settings for take-off, cruise, feather, and reverse thrust. The low-pressure turbine was built by MTU to provide higher shaft power in comparison with the standard PW2037. The demonstrator was provided with 45 vanes located 2.6 fan chords downstream of the rotor, and 10 case struts approximately 1 fan chord downstream of the vanes. The inlet, mid-duct, and exhaust linings were acoustically treated. Acoustic surveys were taken in the for-ward thrust mode for fan speeds of 898, 1120, 1205, and 1302 R.P.M., and at tunnel speeds of 25, 50, 100, and 140 kts. The lowest speed was achieved with the wind tunnel fans at flat pitch, but with the engine pumping the test section Microphone signals were recorded for 30 seconds at 5 deg. increments. These measurements will be used to assess the effects of forward speed on UHB engines, to compare these effects with the corresponding characteristics of conventional bypass ratio engines, and to discuss the various aspects of testing large engines in the wind tunnel.

Horne, W. C.↗

Manipulating mesoscopic multipartite entanglement with atom-light interfaces

Entanglement between two macroscopic atomic ensembles induced by measurement on an ancillary light system has proven to be a powerful method for engineering quantum memories and quantum state transfer. Here we investigate the feasibility of such methods for generation, manipulation, and detection of genuine multipartite entanglement (Greenberger-Horne-Zeilinger and clusterlike states) between mesoscopic atomic ensembles without the need of individual addressing of the samples. Our results extend in a nontrivial way the Einstein-Podolsky-Rosen entanglement between two macroscopic gas samples reported experimentally in [B. Julsgaard, A. Kozhekin, and E. Polzik, Nature (London) 413, 400 (2001)]. We find that under realistic conditions, a second orthogonal light pulse interacting with the atomic samples, can modify and even reverse the entangling action of the first one leaving the samples in a separable state.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Engineering a biopolymer for vascular embolization based on fundamental polymer principals

Herein we describe the engineering of a potential polymer substitute to metal coils for achieving vascular embolization. Our system is based on a methacrylate end-functionalized polyethylene oxide-polypropylene oxide-polyethylene oxide (PEO-PPO-PEO) triblock copolymer which displays thermal-reversible gelation properties and FCC ordering of the original copolymer while also being able to chemically crosslink. This system shows injectability, two-step gelation, chemical crosslinking with a five-fold increase in modulus and is highly resistant to washout under physiological flow conditions. Furthermore, we show that exposure to aqueous flow imparts resistance to swelling where less than 10 % swelling was observed under physiological flow as opposed to more than 60 % under static conditions after 30 days. Auxiliary experiments with PEO-PPO-PEO copolymers of various molecular weights indicate that this phenomenon may possibly be attributed to entanglements known to occur between adjacent micelles, where the reptation time, the time for polymer disentanglement, is long compared to the flow rate.

36 MATERIALS SCIENCE↗

GRB 091024A and the nature of ultra-long gamma-ray bursts

We present a broadband study of gamma-ray burst (GRB) 091024A within the context of other ultra-long-duration GRBs. An unusually long burst detected by Konus-Wind (KW), Swift, and Fermi, GRB 091024A has prompt emission episodes covering ∼1300 s, accompanied by bright and highly structured optical emission captured by various rapid-response facilities, including the 2 m autonomous robotic Faulkes North and Liverpool Telescopes, KAIT, S-LOTIS, and the Sonoita Research Observatory. We also observed the burst with 8 and 10 m class telescopes and determine the redshift to be z = 1.0924 ± 0.0004. We find no correlation between the optical and γ-ray peaks and interpret the optical light curve as being of external origin, caused by the reverse and forward shock of a highly magnetized jet (R{sub B} ≈ 100-200). Low-level emission is detected throughout the near-background quiescent period between the first two emission episodes of the KW data, suggesting continued central-engine activity; we discuss the implications of this ongoing emission and its impact on the afterglow evolution and predictions. We summarize the varied sample of historical GRBs with exceptionally long durations in gamma-rays (≳1000 s) and discuss the likelihood of these events being from a separate population; we suggest ultra-long GRBs represent the tail of the duration distribution of the long GRB population.

79 ASTRONOMY AND ASTROPHYSICS↗

Problems in propulsion system integration

Jet engine components are considered that influence propulsion system integration on the airframe and related aircraft drag areas. Emphasis is placed on high Mach number inlet geometries, boattailed nozzle configurations, propulsive wing installation, wing surface blowing lift, fuselage mounted nacelles, and thrust reversal.

Henderson, W. P.↗

Liquid chromatographic analysis of a formulated ester from a gas-turbine engine test

Size exclusion chromatography (SEC) utilizing mu-Bondagel and mu-Styragel columns with a tetrahydrofuran mobile phase was used to determine the chemical degradation of lubricant samples from a gas-turbine engine test. A MIL-L-27502 candidate, ester-based lubricant was run in a J57-29 engine at a bulk oil temperature of 216 C. In general, the analyses indicated a progressive loss of primary ester, additive depletion, and formation of higher molecular weight material. An oil sample taken at the conclusion of the test showed a reversal of this trend because of large additions of new oil. The high-molecular-weight product from the degraded ester absorbed strongly in the ultraviolet region at 254 nanometers. This would indicate the presence of chromophoric groups. An analysis of a similar ester lubricant from a separate high-temperature bearing test yielded qualitatively similar results.

Jones, W. R., Jr.↗

Towards Accurate and Efficient Predictions of Martensitic Transition Temperatures for Shape Memory Alloys from First Principles

Shape memory alloys (SMAs) can remember and recover their original shapes upon heating due to the existence of a reversible martensitic transition (MT) between the high-temperature austenite (A) and low-temperature martensite (M) phases. The martensitic transition temperature (MTT) is a crucial characteristic of an SMA. SMAs have a wide range of potential applications in aerospace, civil engineering, bioengineering, etc., but their operating temperatures are limited by the available SMAs. MTT can be tuned by alloying a binary with other metals, and the multicomponent NiTi-based SMAs have attracted tremendous research efforts recently. It is not efficient to employ the trial-and-error method alone due to the dramatically increased complexity and possibilities in compositions, and thus reliable theory and accurate computations play an indispensable role in creating SMAs with desirable properties.

Zhigang Wu↗

An Ultrafast, Durable, and High-Loading Polymer Anode for Aqueous Zinc-Ion Batteries and Supercapacitors

Zn metal has shown promise as an anode material for grid-level energy storage, yet is challenged by dendritic growth and low Coulombic efficiency. Herein, an ultrafast, stable, and high-loading polymer anode for aqueous Zn-ion batteries and capacitors (ZIBs and ZICs) is developed by engineering both the electrode and electrolyte. The anode polymer is rationally prepared to have a suitable electronic structure and a large pi-conjugated structure, whereas the electrolyte is manufactured based on the superiority of triflate anions over sulfate anions, as analyzed and confirmed via experiments and simulations. This dual engineering results in an optimal polymer anode with a low discharge potential, near-theoretical capacity, ultrahigh-loading capability (approximate to 50 mg cm -2 ), ultrafast rate (100 A g -1 ), and ultralong lifespan (one million cycles). Further, its mechanism involves reversible Zn 2+ /proton co-storage at the carbonyl site. When the polymer anode is coupled with cathodes for both ZIB and ZIC applications, the devices demonstrate ultrahigh power densities and ultralong lifespans, far surpassing those of corresponding Zn-metal-based devices.

25 ENERGY STORAGE↗