Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Two-dimensional Navier-Stokes heat transfer analysis for rough turbine blades

A quasi-three-dimensional thin-layer Navier-Stokes analysis was used to predict heat transfer to rough surfaces. Comparisons are made between predicted and experimental heat transfer for turbine blades and flat plates of known roughness. The effect of surface roughness on heat transfer was modeled using a mixing length approach. The effect of near-wall grid spacing and convergence criteria on the accuracy of the heat transfer predictions are examined. An eddy viscosity mixing length model having an inner and outer layer was used. A discussion of the appropriate model for the crossover between the inner and outer layers is included. The analytic results are compared with experimental data for both flat plates and turbine blade geometries. Comparisons between predicted and experimental heat transfer showed that a modeling roughness effects using a modified mixing length approach results in good predictions of the trends in heat transfer due to roughness.

Boyle, R. J.↗

Pseudomorphic growth of InAs on misoriented GaAs for extending quantum cascade laser wavelength

The authors have studied the impact of epilayer strain on the deposition of InAs/GaAs on (100) and (111)B with 2° offset toward<2-1-1> surfaces. Consequences of a 7% lattice mismatch between these orientations in the form of three-dimensional growth are less apparent for (111)B with 2° offset toward<2-1-1> surfaces compared to (100). By exploring a range of molecular beam epitaxy process parameters for InAs/GaAs growth and utilizing scanning electron microscopy, atomic force microscopy, and Raman spectroscopy to evaluate the quality of these strained layers, the authors develop empirical models that describe the influence of the process conditions in regards to surface roughness with >92% accuracy. The smoothest InAs/GaAs samples demonstrated average surface roughness of 0.08 nm for 10 μm{sup 2} areas, albeit at very low deposition rates. The authors have found the most important process conditions to be substrate temperature and deposition rate, leading us to believe that controlling diffusion length may be the key to reducing defects in severely strained structures. InGaAs/AlGaAs quantum cascade laser structures were also produced on (111)B with 2° offset toward<2-1-1> to take advantage of the piezoelectric effect, and the modified laser transitions due to these effects were observed.

36 MATERIALS SCIENCE↗

Ceramic Strain Gages for Use at Temperatures up to 1500 Celsius

Indium-tin-oxide (ITO) thin film strain gages were successfully demonstrated at temperatures beyond 1500 C. High temperature static strain tests revealed that the piezoresistive response and electrical stability of the ceramic sensors depended on the thickness of the ITO films comprising the active strain elements. When 2.5 microns-thick ITO films were employed as the active strain elements, the piezoresistive response became unstable at temperatures above 1225 C. In contrast to this, ceramic sensors prepared with 5 microns-thick ITO were stable beyond 1430 C and sensors prepared with 8 microns-thick ITO survived more than 20 hr of operation at 1481 C. Very thick (10 microns) ITo strain gages were extremely stable and responsive at 1528 C. ESCA depth profiles confirmed that an interfacial reaction between the ITO strain gage and alumina substrate was responsible for the high temperature electrical stability observed. Similar improvements in high temperature stability were achieved by doping the active ITO strain elements with aluminum. Several Sic-Sic CMC constant strain beams were instrumented with ITO strain gages and delivered to NASA for testing. Due to the extreme surface roughness of the CMC substrates, new lithography techniques and surface preparation methods were developed. These techniques relied heavily on a combination of Sic and A12O3 cement layers to provide the necessary surface finish for efficient pattern transfer. Micro-contact printing using soft lithography and PDMS stamps was also used to successfully transfer the thin film strain gage patterns to the resist coated CMC substrates. This latter approach has considerable potential for transferring the thin film strain gage patterns to the extremely rough surfaces associated with the CMC's.

Gregory, Otto↗

Effects of Mineral Surface Properties on Supercritical CO 2 Wettability in a Siliciclastic Reservoir

Wettability is a key reservoir characteristic influencing geological carbon sequestration (GCS) processes, such as CO 2 transport and storage capacity. Wettability is often determined on a limited number of reservoir samples by measuring the contact angle at the CO 2 /brine/mineral interface, but the ability to predict this value remains a challenge. In this work, minerals comprising a natural reservoir sample were identified, and the influence of their surface roughness and mineralogy on the contact angle was quantified to evaluate predictive models and controlling mechanisms. The natural sample was obtained from the Mount Simon formation, a representative siliciclastic reservoir that is the site of a United States Department of Energy CO 2 injection project. A thin section of the Mount Simon sandstone was examined with compound light microscopy and environmental scanning electron microscopy (ESEM) coupled with energy-dispersive X-ray spectroscopy (EDS). Quartz and feldspar were identified as dominant minerals and were coated with various reddish black precipitates consistent with illite clay and iron oxide hematite. Contact angle (θ) measurements were conducted for the four representative minerals and the Mount Simon sample over a range of pressures (2–25 MPa) at 40 °C. At supercritical conditions, all samples are strongly water-wet, with contact angles between 27° and 45°. Several predictive models for contact angle were evaluated for the mineral and Mount Simon samples, including the Wenzel and Cassie–Baxter models, plus newly proposed modifications of these that account for the fraction of different minerals comprising the reservoir sample surface, the surface roughness, and the extent that roughness pits are filled with brine. Modeling results suggest that the fraction of mineral surfaces containing roughness pits filled with brine is the most important reservoir characteristic that controls wettability in the Mount Simon sandstone, followed by surface mineralogy. Finally, to our knowledge, this is one of the few studies to investigate the effects of individual minerals on the wettability of a natural reservoir sample.

58 GEOSCIENCES↗

Surface Quality of AMg2 Aluminum Alloy with Ultrafine Grain Structure after Machining. 1. Turning

The influence of cutting on the surface roughness and undulation of AMg2 aluminum alloy with regular and ultrafine grain structure is considered. The quantitative influence of profile filters on its surface roughness and undulation is established, on the basis of 2D parameters. In the machining of materials with ultrafine grain structure, the surface quality is better than for materials with regular grain structure.

42 ENGINEERING↗

Dependence of the Electron Beam Energy and Types of Surface to Determine EBSD Indexing Reliability in Yttria-Stabilized Zirconia

Electron backscatter diffraction (EBSD) is a powerful technique for the surface microstructure analysis. EBSD analysis of cubic yttria-stabilized zirconia (YSZ) in two and three dimensions (2-D, 3-D) is demonstrated using sequential slicing from a focused ion beam (FIB) followed by EBSD mapping to represent 3-D reconstructed high density grain structure with random orientation. The statistics related to accuracy of EBSD band detection shows that probability of accurate grain orientation detection increased significantly when the electron beam energy is increased from 10 kV to 30 kV. As a result of better sampling with increased interaction volume, a disparity between local and average grain orientation angle also exhibited the dependence of the electron beam energy to determine the accuracy of grain orientation. To study the accuracy and quality of EBSD band detection as a function of surface roughness and over layer formation, rapid EBSD measurement tests are performed on (a) YSZ surfaces ion-polished at ion beam energies of 65 nA at 30 kV and 1 nA at 30 kV and (b) carbon coated versus uncoated YSZ surfaces. The EBSD results at both 10 kV and 30 kV electron beam energies indicate that EBSD band detection accuracy is negatively affected by surface roughness and amorphous over layer formation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Surface Chemistry and Particle Morphology Changes in Pine Biomass under Indirect Thermal Gradients: Implications for Feed Screw Design

The conversion of biomass feedstocks into fuels and chemicals using fast pyrolysis is a promising approach to renewable energy. Feed screws that convey biomass to pyrolysis reactors, however, often encounter plugging. Indirect heating of the feed screw occurs due to contact with the pyrolysis chamber, resulting in a heating gradient ranging from ambient temperature (22 °C) to reactor temperature (500 °C). Given that major cell wall macromolecules, such as lignin, cellulose, and hemicellulose, begin to produce bio-oils and volatile resin acid compounds within this temperature gradient, we hypothesized that indirect heating during feed screw conveyance is sufficient to cause premature degradation of biomass. We characterized this degradation by observing increases in surface roughness, changes in overall particle morphology, and the production and deposition of bio-oils on biomass particle surfaces. Correlative analysis between optical in situ hot-stage microscopy, confocal Raman spectroscopy, and SEM analysis revealed that heating at temperatures as low as 375 °C caused significant increases in surface roughness, with large fissures forming between and within cell walls. Additionally, droplets of bio-oil were observed on particles, especially in the bark and cambium samples. This work suggests that these phenomena contribute to particle agglomeration, leading to feed screw plugging, and that engineering a solution to cool the feed screw could prevent particle agglomeration and reduce plugging incidents, thereby increasing biomass processing efficiency.

09 BIOMASS FUELS↗

Effect of cryogenic temperatures and processing parameters on gradient-structure of a stainless steel treated by ultrasonic surface mechanical attrition treatment

Highlights: • Gradient microstructures made by SMAT are investigated for an austenitic 304 L steel. • Cryogenic shot peening reduces the surface roughness. • Cryogenic condition increases subsurface hardening by formation of additional martensite. • The maximum martensite fraction is always located at the subsurface. • Combination of parameters allow to tailor broad ranges of hardness and roughness. - Abstract: The beneficial effect of using cryogenic temperatures for the ultrasonic surface mechanical attrition treatment (SMAT) is depicted in the case of the 304 L austenitic stainless steel. The cryogenic temperatures induce an additional driving force for the formation of martensite at depth where the effect of shot peening tends to vanish, raising the subsurface hardness by 20 to 30%. The maximum amount of α′ martensite was always located within the subsurface. This is explained by different mechanisms operating at different stages during the SMAT process: (i) higher shear stresses at the subsurface due to the Hertzian contact stress, (ii) local heating due to the shot impacts and (iii) surface martensite destabilization when the microstructure enters the nanometric range. Consequently, the gradient structure formed by the SMAT superimposes different natures of gradients in terms of grain size and martensitic fraction. The steel being harder to deform at cryogenic temperatures, a significant decrease of the apparent surface roughness (down to 44%) is also obtained. An appropriate selection of processing parameters allows to tailor the surface towards a broad range of hardness and roughness values: 425 to 560 HV and 1.6 to 3.3 μm, respectively.

36 MATERIALS SCIENCE↗

Development of a New Method to Investigate the Dynamic Friction Behavior of Interfaces Using a Kolsky Tension Bar

In order to understand interfacial interaction of a bi-material during an impact loading event, the dynamic friction coefficient is one of the key parameters that must be characterized and quantified. In this study, a new experimental method to determine the dynamic friction coefficient between two metals was developed by using a Kolsky tension bar and a custom-designed friction fixture. Polyvinylidene fluoride (PVDF) force sensors were used to measure the normal force applied to the friction tribo pairs and the friction force was measured with conventional Kolsky tension bar method. To evaluate the technique, the dynamic friction coefficient between 4340 steel and 7075-T6 aluminum was investigated at an impact speed of approximately 8 m/s. Additionally, the dynamic friction coefficient of the tribo pairs with varied surface roughness was also investigated. The data suggest that higher surface roughness leads to higher friction coefficients at the same speed of 8 m/s.

36 MATERIALS SCIENCE↗

An almost 'perfectly' diffuse, 'perfect' reflector for far-infrared reflectance calibration

Specular and diffuse reflectance measurements made near normal incidence of two very rough, solid aluminum surfaces are presented for the wavelength range from 2.2 to 512 microns. The diffuse measurements made at nonspecular angles by two different detectors indicate that between 33 and 201 microns the reflectance of one surface is nearly Lambertian (isotropic) with a bidirectional reflectance distribution function (BRDF) value within 32 percent of the theoretical value of (1/pi)/sr for a perfectly diffuse, perfect reflector. Photometric reflectance spectra at the specular angle show that between 6.9 and 100 microns the specular BRDF of these surfaces is within 5 percent of the theoretical value of (1/pi)/sr. At longer wavelengths of 235, 320, and 512 microns the specular reflectance rapidly departs from that of a perfectly diffuse, perfect reflector. The two samples studied have rms surface roughnesses of 44 and 60 microns. A durable metal surface with these near perfect reflectance characteristics can be advantageously used in the FIR as a black-body source, the interior surface of an integrating sphere, and most especially as an absolute calibration standard. BRDF measurements at 40 deg incidence, though still highly diffuse, show a significant departure from Lambertian reflectance.

Smith, Sheldon M.↗

An integrated optical CO2 sensor. Phase 0: Design and fabrication of critical elements

Significant progress has been made toward all of the goals for the first phase of the project short of actual fabrication of a light path. Two alternative approaches to fabricating gold mirrors using the basic LIGA process were developed, one using electroplated solid gold mirrors and the second using gold plated over a nickel base. A new method of fabrication, the transfer mask process, was developed and demonstrated. Analysis of the projected surface roughness and beam divergence effects was completed. With gold surface with low surface roughness scattering losses are expected to be insignificant. Beam divergence due to diffraction will require a modification of the original design, but should be eliminated by fabricating mirrors 1000 mu m in height by 1000 mu m in width and using a source with an initial beam radius greater than 300 mu m. This may eliminate any need for focusing optics. Since the modified design does not affect the mask layout, ordering of the mask and fabrication of the test structures can begin immediately at the start of Phase 1.

Murphy, Michael C.↗

Enhanced surface flashover strength in vacuum of polymethylmethacrylate by surface modification using atmospheric-pressure dielectric barrier discharge

Polymer materials, such as polymethylmethacrylate (PMMA), are widely used as insulators in vacuum. The insulating performance of a high-voltage vacuum system is mainly limited by surface flashover of the insulators rather than bulk breakdown. Non-thermal plasmas are an efficient method to modify the chemical and physical properties of polymer material surfaces, and enhance the surface insulating performance. In this letter, an atmospheric-pressure dielectric barrier discharge is used to treat the PMMA surface to improve the surface flashover strength in vacuum. Experimental results indicate that the plasma treatment method using Ar and CF{sub 4} (10:1) as the working gas can etch the PMMA surface, introduce fluoride groups to the surface, and then alter the surface characteristics of the PMMA. The increase in the surface roughness can introduce physical traps that can capture free electrons, and the fluorination can enhance the charge capturing ability. The increase in the surface roughness and the introduction of the fluoride groups can enhance the PMMA hydrophobic ability, improve the charge capturing ability, decrease the secondary electron emission yield, increase the surface resistance, and improve the surface flashover voltage in vacuum.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

An Experimental Study of the Aerodynamics of a Swept and Unswept Semispan Wing with a Simulated Glaze Ice Accretion

Two semispan wings, one with a rectangular planform and one with 30 degrees of leading edge sweep were tested. Both had a NACA 0012 airfoil section, and both were tested clean and with simulated glaze ice shapes on their leading edges. Several surface roughness were tested. Each model geometry is documented and each surface roughness is explained. Aerodynamic performance of the wing in the form of sectional lift and integrated three-dimensional lift is documented through pressure measurements obtained from rows of surface pressure taps placed at five span locations on the wing. For the rectangular wing, sectional drag near the midspan is obtained from wake total pressure profiles. The data is presented in tabular and graphical form and is also available on computer disk.

Bragg, Michael B.↗

Corrosion protection of mild steel by superhydrophobic magnetite coating

Corrosion-resistant hydrophobic magnetite coatings on mild steel surfaces were developed by immersion method. The effect of steel surface roughness (R a ) on its hydrophobicity was systematically studied using contact angle measurement (CAM), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The corrosion resistance of hydrophobic magnetite coatings was evaluated using a potentiodynamic polarization test. The durability of the coatings was assessed in air, tap water, and 3.5 wt% NaCl environments. Hydrophobic magnetite coating with a water contact angle of 146-152° showed excellent resistance to corrosion, longevity in atmospheric air, and significant self-cleaning properties. The primary focus of this study was to develop a quick and simple immersion technique to create hydrophobic surfaces on mild steel. Finally, results suggest that surface roughness plays a significant role in surface hydrophobicity, and enhancing the hydrophobicity of mild steel improves its corrosion resistance.

36 MATERIALS SCIENCE↗

Effects of nose bluntness, roughness, and surface perturbations on the asymmetric flow past slender bodies at large angles of attack

The effects of such geometric perturbations as variations of model-tip sharpness and roughness, as well as discrete surface perturbations, on the asymmetric flow past slender bodies is experimentally investigated for the cases of a cone/cylinder model having a 10-deg semiapex angle and a 3.0-caliber tangent ogive model. Both models have base diameters of 3.5 inches, and were tested in laminar flow conditions at angles-of-attack in the 30-60 deg range. Single, discrete roughness elements were represented by beads; bead effectiveness was judged on the basis of the extent to which they affected the flowfield in various conditions.

Moskovitz, Cary A.↗

Ga induced superstructures as templates for lattice matched hetroepitaxial growth of GaN on Si(111) substrate

High quality GaN is grown by plasma assisted molecular beam epitaxy on Ga induced superstructural phases of Si(111)7x7. Three stable surface phases induced by Ga adsorption, viz., (1x1), (6.3x6.3), and ({radical}3x{radical}3)R30 deg., are employed as templates to grow epitaxial (0001) GaN thin films. GaN grown on Si({radical}3x{radical}3)R30 deg. -Ga is found to be highly crystalline with intense (0002) x-ray diffraction and photoluminescence peaks with low full width at half maximum, low surface roughness, and stoichiometric surface composition. The high quality of these GaN films formed at a low temperature of 400 deg. C is explained by the integral (x2) lattice matching between the unit cell of GaN and the ({radical}3x{radical}3) phase. The experiments demonstrate a plausible approach of adsorbate induced surface modifications as templates for III-V hetroepitaxy on Si surfaces.

36 MATERIALS SCIENCE↗

Effect of PVD-coated chromium on the subcooled flow boiling performance of nuclear reactor cladding materials

Here we elucidate the separate effect of a thin Cr coating deposited by physical vapor deposition (PVD) on the subcooled flow boiling performance of zircaloy-4. First, we run flow boiling experiments on prototypical zircaloy-4 surfaces mimicking the scratch pattern and surface roughness of nuclear reactor claddings. Then, we PVD-coat a 0.3 µm thick chromium layer on the same exact surface and repeat the same flow boiling investigations. All experiments are run using deionized water at atmospheric pressure, flowing on a 1 × 3 cm 2 rectangular cross section channel at a rate of 1000 kg/m 2 /s and a subcooling of 10 K. We measure the average temperature of the boiling surface at increasing surface heat fluxes, covering a wide range of heat transfer regimes, from single-phase forced convection to the boiling crisis. We also record high-speed videos of the boiling process, which we postprocess to measure bubble nucleation site density, growth time, departure diameter and frequency. The surface analysis reveals that, while the chromium coating does not seem change the surface roughness and morphology, it improves surface wettability. However, it decreases the critical heat flux. The chromium coating causes an increase of nucleation temperature, bubble departure diameter and growth time, and a reduction of the nucleation site density. The concurrence of these observations indicates that a size reduction of the nucleation sites, conformally covered by the chromium coating, may be the cause of the boiling performance deterioration. We confirm this hypothesis repeating the same analysis on a FeCrAl sample prepared and tested using the same protocol as the zircaloy-4 sample, but with a different initial surface texture.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Thermal characteristics of the moon.

The papers describe earth-based and in situ surface measurements of the thermal characteristics of lunar-type materials. A geophysical interpretation of the thermal history of the moon is given. Microwave emission from the moon and radar mapping of lunar surface roughness are studied. Lunar thermal aspects from Surveyor data, lunar surface temperatures from Apollo 11 data, the development of an in situ thermal conductivity measurement for the lunar heat flow experiment, and the Apollo 15 lunar heat flow measurement are reviewed. Thermal properties of granulated materials, thermal property measurements on lunar material returned by Apollo 11 and 12 missions, and thermal characteristics of lunar surface roughness are discussed. Individual items are abstracted in this issue.

Lucas, J. W.↗