Search NASA⌕ Search

SEARCH · Search NASA

Results for “stream flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Experimental Investigation of Centrifugal Compressor Stabilization Techniques

Results from a series of experiments to investigate techniques for extending the stable flow range of a centrifugal compressor are reported. The research was conducted in a high-speed centrifugal compressor at the NASA Glenn Research Center. The stabilizing effect of steadily flowing air-streams injected into the vaneless region of a vane-island diffuser through the shroud surface is described. Parametric variations of injection angle, injection flow rate, number of injectors, injector spacing, and injection versus bleed were investigated for a range of impeller speeds and tip clearances. Both the compressor discharge and an external source were used for the injection air supply. The stabilizing effect of flow obstructions created by tubes that were inserted into the diffuser vaneless space through the shroud was also investigated. Tube immersion into the vaneless space was varied in the flow obstruction experiments. Results from testing done at impeller design speed and tip clearance are presented. Surge margin improved by 1.7 points using injection air that was supplied from within the compressor. Externally supplied injection air was used to return the compressor to stable operation after being throttled into surge. The tubes, which were capped to prevent mass flux, provided 9.3 points of additional surge margin over the baseline surge margin of 11.7 points.

Skoch, Gary J.↗

Effect of Flow Incidence and Reynolds Number on Low-Speed Aerodynamic Characteristics of Several Noncircular Cylinders with Applications to Directional Stability and Spinning

The aerodynamic characteristics of several noncircular two-dimensional cylinders with axes normal to the stream at various flow incidences (analogous to angles of attack of a two-dimensional airfoil and obtained by rotating the cylinders about their axes) for a range of Reynolds numbers have been determined from low-speed wind-tunnel tests. The results indicate that these parameters have rather large effects on the drag and side force developed on these cylinders. The side force is especially critical and very often undergoes a change in sign with a change in Reynolds number. Since the flow incidences correspond to combined angles of attack and sideslip in the crossflow plane of three-dimensional bodies, these two-dimensional results appear to have strong implications with regard to directional stability of fuselages at high angles of attack. These implications, along with those associated with the spin-recovery characteristics of aircraft, are briefly discussed.

Polhamus, Edward C.↗

Solar Energetic Particles and Space Weather

The solar energetic particles (SEPs) of consequence to space weather are accelerated at shock waves driven out from the Sun by fast coronal mass ejections (CMEs). In the large events, these great shocks fill half of the heliosphere. SEP intensity profiles change appearance with longitude. Events with significant intensities of greater than ten MeV protons occur at an average rate of approx. 13 per year near solar maximum and several events with high intensities of > 100 McV protons occur each decade. As particles stream out along magnetic field lines from a shock near the Sun, they generate waves that scatter subsequent particles. At high intensities, wave growth throttles the flow below the 'streaming limit.' However, if the shock maintains its strength, particle intensities can rise above this limit to a peak when the shock itself passes over the observer creating a 'delayed' radiation hazard, even for protons with energies up to approx. one GeV. The streaming limit makes us blind to the intensities at the oncoming shock, however, heavier elements such as He, O, and Fe probe the shape of the wave spectrum, and variation in abundances of these elements allow us to evade the limit and probe conditions at the shock, with the aid of detailed modeling. At high energies, spectra steepen to form a spectral 'knee'. The location of the proton spectral knee can vary from approx. ten MeV to approx. one GeV, depending on shock conditions, greatly affecting the radiation hazard. Hard spectra are a serious threat to astronauts, placing challenging requirements for shielding, especially on long-duration missions to the moon or Mars.

Reames, Donald V.↗

Use of Remote Technology in the Surface Water Environmental Monitoring Program at SRS Reducing Measurements in the Field - 13336

There are a wide range of sensor and remote technology applications available for use in environmental monitoring programs. Each application has its own set of limitations and can be challenging when attempting to utilize it under diverse environmental field conditions. The Savannah River Site Environmental Monitoring Program has implemented several remote sensing and surface water flow technologies that have increased the quality of the data while reducing the number of field measurements. Implementation of this technology reduced the field time for personnel that commute across the Savannah River Site (SRS) over a span of 310 square miles. The wireless surface water flow technology allows for immediate notification of changing field conditions or equipment failure thus reducing data-loss or erroneous field data and improving data-quality. This wireless flow technology uses the stage-to-flow methodology coupled with implementation of a robust highly accurate Acoustic Doppler Profiler system for measuring discharge under various field conditions. Savings for implementation of the wireless flow application and Flowlink{sup R} technology equates to approximately 1175 hours annually for the radiological liquid effluent and surveillance programs. The SonTek River Suveyor and Flowtracker technologies are utilized for calibration of the wireless flow monitoring devices in the site streams and validation of effluent flows at the SRS. Implementation of similar wireless devices is also planned in the National Pollutant Discharge Elimination System (NPDES) Storm-water Monitoring Program. SRS personnel have been developing a unique flow actuator device. This device activates an ISCO{sup TM} automated sampler under flowing conditions at storm-water outfall locations across the site. This technology is unique in that it was designed to be used under field conditions with rapid changes in flow and sedimentation where traditional actuators have been unsuccessful in tripping the automated sampler. In addition, automated rain gauges will be tied into this technology for immediate notification of rain at storm-water locations further enhancing the automation of environmental data collection. These technological improvements at SRS have led to data-quality improvements while reducing the field technician time in the field and costs for maintaining the traditional environmental monitoring applications. (authors)

54 ENVIRONMENTAL SCIENCES↗

ZFP Hardware Implementation

ZFP is a floating-point compression format gaining traction in high-performance computing applications. A software implementation has demonstrated the ability to reduce data movement across communication channels and to reduce the footprint of floating-point arrays in memory. Nevertheless, any benefit in performance is limited to the spare compute cycles available before reaching bandwidth limitations. A hardware implementation of ZFP has the potential to substantially improve HPC application performance. Hardware compression speedup over software alone on a single CPU core ranges from 15x for 1-D arrays to over 200x for 3-D arrays. The implementation of ZFP is sourced in SystemC to facilitate its evaluation in various architectures. The encode pipeline consists of several modules. Uncompressed blocks of floating-point numbers in IEEE format flow into the pipeline in a stream and a compressed bitstream flows out from the pipeline. The decode pipeline is the inverse of the encode pipeline. A modular design enables formats other than IEEE (such as posits) to be considered with minor adaptations. Best performance will be realized from the hardware ZFP unit when batches of blocks are processed at a time. The implementation supports 1-D, 2- D and 3-D blocks of floating-point numbers. The hardware implementation of ZFP has been validated with the software implementation of ZFP. C++ template parameters are used to specify the bit width of floating-point numbers and the array dimension of the encoder. A test bench program has been created with several test cases, some with continuous data that is ideal for ZFP, and others with extreme cases containing numbers near or at the maximum or minimum values supported by the number format.

Lloyd, GS↗

A decade of computer simulations for space shuttle aerodynamics

Ten years ago computer simulations of the flow field around the Space Shuttle Orbiter were limited to inviscid calculations for the windward side of the forebody and viscous calculations for selected 2-D problems. Advances in computer hardware and numerical methods during the past ten years made it possible to calculate viscous flow over the complete orbiter configuration at angle of attack. The equations solved are the Reynolds-averaged, Navier-Stokes equation, simplified by either the thin-layer or parabolized approximation. An algebraic eddy viscosity model is used for turbulent flow. The free stream is assumed to be a perfect gas for wind tunnel conditions and a real gas in thermodynamic equilibrium for flight conditions. Four examples of recent computer simulations are presented. Flow field results include oil flow patterns on the surface and Mach number contours, isobars, and cross-flow velocity vectors in the shock layer.

Inouye, Mamoru↗

A decade of computer simulations for Space Shuttle aerodynamics

Ten years ago computer simulations of the flow field around the Space Shuttle Orbiter were limited to inviscid calculations for the windward side of the forebody and viscous calculations for selected 2-D problems. Advances in computer hardware and numerical methods during the past ten years made it possible to calculate viscous flow over the complete orbiter configuration at angle of attack. The equations solved are the Reynolds-averaged, Navier-Stokes equation, simplified by either the thin-layer or parabolized approximation. An algebraic eddy viscosity model is used for turbulent flow. The free stream is assumed to be a perfect gas for wind tunnel conditions and a real gas in thermodynamic equilibrium for flight conditions. Four examples of recent computer simulations are presented. Flow field results include oil flow patterns on the surface and Mach number contours, isobars, and cross-flow velocity vectors in the shock layer.

Inouye, Mamoru↗

The influence of free-stream turbulence on separation of turbulent boundary layers in incompressible, two-dimensional flow

Experiments were conducted to determine if free-stream turbulence scale affects separation of turbulent boundary layers. In consideration of possible interrelation between scale and intensity of turbulence, the latter characteristic also was varied and its role was evaluated. Flow over a 2-dimensional airfoil in a subsonic wind tunnel was studied with the aid of hot-wire anemometry, liquid-film flow visualization, a Preston tube, and static pressure measurements. Profiles of velocity, relative turbulence intensity, and integral scale in the boundary layer were measured. Detachment boundary was determined for various angles of attack and free-stream turbulence. The free-stream turbulence intensity and scale were found to spread into the entire turbulent boundary layer, but the effect decreased as the airfoil surface was approached. When the changes in stream turbulence were such that the boundary layer velocity profiles were unchanged, detachment location was not significantly affected by the variations of intensity and scale. Pressure distribution remained the key factor in determining detachment location.

Potter, J. Leith↗

Gas stream in Algol

Additional absorption features in the red wings of the Mg II resonance lines near 2800 A are found in observations of Algol made from the Copernicus satellite. The absorption features were clearly seen only during a part of the primary eclipse, in the phase interval 0.90-0.03. The observations are interpreted as being produced by a stream of matter flowing from Algol B in the direction of Algol A. The measured Doppler shifts of the features give the value of 150 km/s as the characteristic velocity of matter in the stream. The mass transfer connected with the stream is estimated to be of the order of 10 to the -13th power solar mass per year.

Cugier, H.↗

Evolution of OH and CO-dark molecular gas fraction across a molecular cloud boundary in Taurus

We present observations of {sup 12}CO J = 1-0, {sup 13}CO J = 1-0, H i, and all four ground-state transitions of the hydroxyl (OH) radical toward a sharp boundary region of the Taurus molecular cloud. Based on a photodissociation region (PDR) model that reproduces CO and [C i] emission from the same region, we modeled the three OH transitions, 1612, 1665, and 1667 MHz successfully through escape probability non-local thermal equilibrium radiative transfer model calculations. We could not reproduce the 1720 MHz observations, due to unmodeled pumping mechanisms, of which the most likely candidate is a C-shock. The abundance of OH and CO-dark molecular gas is well-constrained. The OH abundance [OH]/[H{sub 2}] decreases from 8×10{sup −7} to 1×10{sup −7} as A{sub v} increases from 0.4 to 2.7 mag following an empirical law: which is higher than PDR model predictions for low-extinction regions by a factor of 80. The overabundance of OH at extinctions at or below 1 mag is likely the result of a C-shock. The dark gas fraction (DGF, defined as the fraction of molecular gas without detectable CO emission) decreases from 80% to 20% following a Gaussian profile: This trend of the DGF is consistent with our understanding that the DGF drops at low visual extinction due to photodissociation of H{sub 2} and drops at high visual extinction due to CO formation. The DGF peaks in the extinction range where H{sub 2} has already formed and achieved self-shielding but {sup 12}CO has not. Two narrow velocity components with a peak-to-peak spacing of ∼1 km s{sup −1} were clearly identified. Their relative intensity and variation in space and frequency suggest colliding streams or gas flows at the boundary region.

79 ASTRONOMY AND ASTROPHYSICS↗

Dynamic behavior of chemical exchange column in a water detritiation system for a fusion reactor

The dynamic behavior of a CECE column used for a demonstration reactor (DEMO) plant has been studied. In the case where the column was filled with natural water, the time required to achieve steady state was almost the same as that for the column operated under the total reflux mode. The manipulated variables were flow rate of the bottom stream for the control of the bottom tritium concentration, and flow rate of the hydrogen stream for the control of the top tritium concentration. For both the variables, the response curve was expressed by the first-order lag system, and a PID controller could be applied. (authors)

07 ISOTOPE AND RADIATION SOURCES↗

The turbomachine blading design using S2-S1 approach

The boundary conditions corresponding to the design problem when the blades being simulated by the bound vorticity distribution are presented. The 3D flow is analyzed by the two steps S2 - S1 approach. In the first step, the number of blades is supposed to be infinite, the vortex distribution is transformed into an axisymmetric one, so that the flow field can be analyzed in a meridional plane. The thickness distribution of the blade producing the flow channel striction is taken into account by the modification of metric tensor in the continuity equation. Using the meridional stream function to define the flow field, the mass conservation is satisfied automatically. The governing equation is deduced from the relation between the azimuthal component of the vorticity and the meridional velocity. The value of the azimuthal component of the vorticity is provided by the hub to shroud equilibrium condition. This step leads to the determination of the axisymmetric stream sheets as well as the approximate camber surface of the blade. In the second step, the finite number of blades is taken into account, the inverse problem corresponding to the blade to blade flow confined in each stream sheet is analyzed. The momentum equation implies that the free vortex of the absolute velocity must be tangential to the stream sheet. The governing equation for the blade to blade flow stream function is deduced from this condition. At the beginning, the upper and the lower surfaces of the blades are created from the camber surface obtained from the first step with the assigned thickness distribution. The bound vorticity distribution and the penetrating flux conservation applied on the presumed blade surface constitute the boundary conditions of the inverse problem. The detection of this flux leads to the rectification of the geometry of the blades.

Luu, T. S.↗

Applying the light: nutrient hypothesis to stream periphyton

The light:nutrient hypothesis (LNH) states that algal nutrient content is determined by the balance of light and dissolved nutrients available to algae during growth. Light and phosphorus gradients in both laboratory and natural streams were used to examine the relevance of the LNH to stream periphyton. Controlled gradients of light (12-426 mol photons m{sup -2} s{sup -1}) and dissolved reactive phosphorus (DRP, 3-344 {mu}g L{sup -1}) were applied experimentally to large flow-through laboratory streams, and natural variability in canopy cover and discharge from a wastewater treatment facility created gradients of light (0.4-35 mol photons m{sup -2} day{sup -1}) and DRP (10-1766 {mu}g L{sup -1}) in a natural stream. Periphyton phosphorus content was strongly influenced by the light and DRP gradients, ranging from 1.8 to 10.7 {mu}g mg AFDM{sup -1} in the laboratory streams and from 2.3 to 36.9 {mu}g mg AFDM{sup -1} in the natural stream. Phosphorus content decreased with increasing light and increased with increasing water column phosphorus. The simultaneous effects of light and phosphorus were consistent with the LNH that the balance between light and nutrients determines algal nutrient content. In experiments in the laboratory streams, periphyton phosphorus increased hyperbolically with increasing DRP. Uptake then began leveling off around 50 {mu}g L{sup -1}. The relationship between periphyton phosphorus and the light: phosphorus ratio was highly nonlinear in both the laboratory and natural streams, with phosphorus content declining sharply with initial increases in the light: phosphorus ratio, then leveling off at higher values of the ratio. Although light and DRP both affected periphyton phosphorus content, the effects of DRP were much stronger than those of light in both the laboratory and natural streams. DRP explained substantially more of the overall variability in periphyton phosphorus than did light, and light effects were evident only at lower phosphorus concentrations ({approx}< 25 {mu}g L{sup -1}) in the laboratory streams. These results suggest that light has a significant negative effect on the food quality of grazers in streams only under a limited set of conditions.

59 BASIC BIOLOGICAL SCIENCES↗

Systems and methods of making carbon nanotubes

A method of producing a carbon nanotube may include heating a convergent flow nozzle and a flow chamber of a carbon nanotube reactor, flowing a vaporized reactant stream through the nozzle and collecting a carbon nanotube product from an outlet of a heated flow chamber disposed downstream of the heated convergent flow nozzle. The vaporized reactant stream may include a carbon nanotube nucleation carbon source, a carbon nanotube growth carbon source, and a carbon nanotube catalyst precursor. The nozzle may have a nozzle contraction ratio of from 3:1 to 300:1.

Wang, Yuhuang↗

A swirl flow evaporative cold plate

A forced flow evaporative cold plate is under development for future application to the thermal bus concept being pursued by NASA for Space Station Thermal Control. The vaporizer is a swirl-flow device employing a spiral tube coil geometry sandwiched between conductive metal plates upon which electric components could be mounted. This concept is based on the inherent phase separation that occurs in a two phase stream in curvilinear flow. This is a zero 'g' design with one 'g' all-attitude capability and is capable of high heat transfer coefficients, good isothermality, and the ability to function at heat fluxes approaching 5w/sq cm on the cold plates (10w/sq cm on the tube wall) with Freon 114. The advantages of this design over other two phase evaporator approaches are high heat flux capability, simplified control requirements, insensitivity to micro-gravity oscillations, and inexpensive manufacturability. The program included design, fabrication, and test of such a cold plate utilizing an existing test stand developed for two-phase thermal management system (TPTMS) testing. Test results analysis and conclusions are included.

Niggemann, R. E.↗

Reducing or stopping the uncontrolled flow of fluid such as oil from a well

The uncontrolled flow of fluid from an oil or gas well may be reduced or stopped by injecting a composition including 2-cyanoacrylate ester monomer into the fluid stream. Injection of the monomer results in a rapid, perhaps instantaneous, polymerization of the monomer within the flow stream of the fluid. This polymerization results in formation of a solid plug that reduces or stops the flow of additional fluid from the well.

42 ENGINEERING↗