Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface codes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47

Postflight aerothermodynamic analysis of Pegasus(tm) using computational fluid dynamic techniques

The objective was to validate the computational capability of the NASA Ames Navier-Stokes code, F3D, for flows at high Mach numbers using comparison flight test data from the Pegasus (tm) air launched, winged space booster. Comparisons were made with temperature and heat fluxes estimated from measurements on the wing surfaces and wing-fuselage fairings. Tests were conducted for solution convergence, sensitivity to grid density, and effects of distributing grid points to provide high density near temperature and heat flux sensors. The measured temperatures were from sensors embedded in the ablating thermal protection system. Surface heat fluxes were from plugs fabricated of highly insulative, nonablating material, and mounted level with the surface of the surrounding ablative material. As a preflight design tool, the F3D code produces accurate predictions of heat transfer and other aerodynamic properties, and it can provide detailed data for assessment of boundary layer separation, shock waves, and vortex formation. As a postflight analysis tool, the code provides a way to clarify and interpret the measured results.

Kuhn, Gary D.↗

A new environment to simulate the dynamics in the close proximity of rubble-pile asteroids

This paper presents a new environment to simulate close-proximity dynamics around rubble-pile asteroids. The code provides methods for modeling the asteroid’s gravity field and surface through granular dynamics. It implements stateof-the-art techniques to model both gravity and contact interaction between particles: 1) mutual gravity as either direct N2 or Barnes-Hut GPU-parallel octree and 2) contact dynamics with a soft-body (force-based, smooth dynamics), hard-body (constraint-based, non-smooth dynamics), or hybrid (constraint-based with compliance and damping) approach. A very relevant feature of the code is its ability to handle complex-shaped rigid bodies and their full 6D motion. Examples of spacecraft close-proximity scenarios and their numerical simulations are shown.

Ferrari, Fabio↗

Simulation of etch pit formation through active sites in carbon fiber micro-structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation as a result of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gasses such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various reaction mechanisms such as adsorption, desorption, Eley-Rideal (ER) and Langmuir-Hinshelwood (LH) mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

Simulation of Etch Pit Formation in DSMC Through Active Sites in Carbon Fiber Micro-Structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation because of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gases such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various detailed surface reaction mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

DSMC Simulation of Etch Pit Formation Through Active Sites in Carbon Fiber Micro-Structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation because of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gases such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various detailed surface reaction mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

Analysis of an advanced ducted propeller subsonic inlet

A time marching Navier-Stokes code called PARC (PARC2D for 2-D/axisymmetric and PARC3D for 3-D flow simulations) was validated for an advanced ducted propeller (ADP) subsonic inlet. The code validation for an advanced ducted propeller (ADP) subsonic inlet. The code validation was implemented for a non-separated flow condition associated with the inlet operating at angles-of-attack of 0 and 25 degrees. The inlet test data were obtained in the 9 x 15 ft Low Speed Wind Tunnel at NASA Lewis Research Center as part of a cooperative study with Pratt and Whitney. The experimental study focused on the ADP inlet performance for take-off and approach conditions. The inlet was tested at a free stream Mach number of 0.2, at angles-of-attack between O and 35 degrees, and at a maximum propeller speed of 12,000 RPM which induced a corrected air flow rate of about 46 lb/sec based on standard day conditions. The computational grid and flow boundary conditions (BC) were based on the actual inlet geometry and the funnel flow conditions. At the propeller face, two types of BC's were applied: a mass flow BC and a fixed flow properties BC. The fixed flow properties BC was based on a combination of data obtained from the experiment and calculations using a potential flow code. Comparison of the computational results with the test data indicates that the PARC code with the propeller face fixed flow properties BC provided a better prediction of the inlet surface static pressures than the predictions when the mass flow BC was used. For an angle-of-attack of 0 degrees, the PARC2D code with the propeller face mass flow BC provided a good prediction of inlet static pressures except in the region of high pressure gradient. With the propeller face fixed flow properties BC, the PARC2D code provided a good prediction of the inlet static pressures. For an angle-of-attack of 25 degrees with the mass flow BC, the PARC3D code predicted statis pressures which deviated significantly from the test data; however, with the fixed flow properties BC, a good comparison with the test data was obtained.

Iek, Chanthy↗

Mars surface radiation exposure for solar maximum conditions and 1989 solar proton events

The Langley heavy-ion/nucleon transport code, HZETRN, and the high-energy nucleon transport code, BRYNTRN, are used to predict the propagation of galactic cosmic rays (GCR's) and solar flare protons through the carbon dioxide atmosphere of Mars. Particle fluences and the resulting doses are estimated on the surface of Mars for GCR's during solar maximum conditions and the Aug., Sep., and Oct. 1989 solar proton events. These results extend previously calculated surface estimates for GCR's at solar minimum conditions and the Feb. 1956, Nov. 1960, and Aug. 1972 solar proton events. Surface doses are estimated with both a low-density and a high-density carbon dioxide model of the atmosphere for altitudes of 0, 4, 8, and 12 km above the surface. A solar modulation function is incorporated to estimate the GCR dose variation between solar minimum and maximum conditions over the 11-year solar cycle. By using current Mars mission scenarios, doses to the skin, eye, and blood-forming organs are predicted for short- and long-duration stay times on the Martian surface throughout the solar cycle.

Simonsen, Lisa C.↗

In Search of the Physics: NASA's Approach to Airframe Noise

An extensive numerical and experimental study of airframe noise mechanisms associated with a subsonic high-lift system has been performed at NASA Langley Research Center (LaRC). Investigations involving both steady and unsteady computations and experiments on small-scale models with part-span flaps and full-span flaps are presented. Both surface (steady and unsteady pressure measurements, hot films, oil flows, pressure sensitive paint) and off-surface (5 holeprobe, particle-imaged velocimetry, laser velocimetry, laser light sheet measurements) were taken in the LaRC Quiet Flow Facility (QFF) and several hard-wall tunnels. Experiments in the Low Turbulence Pressure Tunnel (LTPT) included Reynolds number variations up to flight conditions. Successful microphone array measurements were also taken providing both acoustic source maps on the model, and quantitative spectra. Critical directivity measurements were obtained in the QFF. NASA Langley unstructured and structured Reynolds-Averaged Navier-Stokes codes modeled the steady aspects of the flows. Excellent comparisons with surface and off-surface experimental data were obtained. Subsequently, these meanflow calculations were utilized in both linear stability and direct numerical simulations of the flow fields to calculate unsteady surface pressures and farfield acoustic spectra. Accurate calculations were critical in obtaining not only noise source characteristics, but shear layer correction data as well. Techniques utilized in these investigations as well as brief overviews of the results are given.

Macaraeg, Michele G.↗

photoemission

The code is a python package that implements a one-step model to estimate quantum efficiency of photoemission from solid state surfaces. The analytical formulation is based on the approach proposed in Phys Rev B 95, 075439 (2017). This code extends that formalism from a model Hamiltonian to the calculation of quantum efficiency from the electronic states derived from solid-state quantum mechanical calculations obtained using the VASP code.

Batista, Enrique↗

Solution of the surface Euler equations for accurate three-dimensional boundary-layer analysis of aerodynamic configurations

The three-dimensional boundary-layer equations in the limit as the normal coordinate tends to infinity are called the surface Euler equations. The present paper describes an accurate method for generating edge conditions for three-dimensional boundary-layer codes using these equations. The inviscid pressure distribution is first interpolated to the boundary-layer grid. The surface Euler equations are then solved with this pressure field and a prescribed set of initial and boundary conditions to yield the velocities along the two surface coordinate directions. Results for typical wing and fuselage geometries are presented. The smoothness and accuracy of the edge conditions obtained are found to be superior to the conventional interpolation procedures.

Iyer, V.↗

Aerothermodynamics of Pyrolizing Surfaces in Hypersonic Rarefied Flows

Direct simulation Monte Carlo (DSMC) calculations of rarefied flows about entry bodies typically employ a fixed surface temperature or a radiative-equilibrium energy balance to compute that temperature. Such boundary conditions neglect any effects of heat capacitance and heat conduction in the spacecraft heat shield and, therefore, provide an upper bound for the surface temperature. Such calculations also neglect pyrolysis from the heat shield which can be significant for a high-energy incident flow at very low densities. Accurate prediction of both heating and aerodynamic forces requires including pyrolysis and surface heat transfer in the models for gas-surface interaction employed in DSMC methods. Although these physical models have long appeared in various continuum flow calculation codes, they have only recently appeared in DSMC codes which are required to simulate rarefied flows during entry at high altitudes. In the current implementation, routines from the widely distributed Charring Material Thermal Response and Ablation (CMA) program are coupled into a DSMC code to calculate the one-dimensional heat transfer into the carbon phenolic heat shield at each point on a vehicle surface. Temperature-dependent material properties, surface re-radiation, and in-depth pyrolysis were included in the calculation, but surface ablation was neglected. Sample calculations for entry of the Galileo probe into the atmosphere of Jupiter demonstrate that including pyrolysis in the model leads to significant differences in predicted aerodynamics. Granted, the drag coefficient does not depend strongly on the surface temperature which can itself be significantly below the radiative equilibrium value during entry. However, the surface mass flux due to pyrolysis of the material is significant once the probe drops to altitudes characterized by transition flow. This leads to a noticeable increase in drag and a decrease in heating compared to a body without pyrolysis.

Haas, Brian L.↗

Improving the Estimation of the Atmospheric Water Vapor Pressure Using Interpretable Long Short-Term Memory Networks: Dataset, Python code, and trained models

Atmospheric water vapor pressure is an essential meteorological control on land surface and hydrologic processes. It is not as frequently observed as other meteorologic conditions, but often inferred through the August–Roche–Magnus formula by simply assuming dew point and daily minimum temperatures are equivalent or by empirically correlating the two temperatures using an aridity correction. The performance of both methods varies considerably across different regions and during different time periods; obtaining consistently accurate estimates across space and time remains a great challenge. We applied an interpretable Long Short-Term Memory (iLSTM) network conditioned on static, location specific attributes to estimate daily vapor pressure for 83 FLUXNET sites in the United States and Canada. This data package includes all raw data of the 83 FLUXNET sites, input data for model training/validation/test, trained models and results, and python codes for the manuscript "Improving the Estimation of the Atmospheric Water Vapor Pressure Using an Interpretable Long Short-term Memory Network". Specifically, it consists of five parts. - First, "1_Daymet_data_83sites.zip" includes raw data downloaded from Daymet for the 83 sites used in the paper according to their longitude and latitude, in which vapor pressure is used. It also includes a pre-processed CSV data file combining all data from the 83 sites which is specifically used for the paper. - Second, "2_Fluxnet2015_data_83sites.zip" includes raw half hourly data of the 83 sites downloaded from FLUXNET2015 data portal, pre-processed daily data of the 83 sites, a CSV file including combined pre-processed daily data of the 83 sites, and a CSV file including the information (site ID, site name, latitude, longitude, data available period) of the 83 sites. - Third, "3_MODIS_LAI_data_83sites_raw.zip" includes raw leaf area index (LAI) data downloaded from the AppEEARs data portal. - Fourth, "4_Scripts.zip" includes all scripts related to model training and post-processing of a trained model, and a jupyter notebook showing an example for model post-processing. Two typo errors in files titled "run2get_args.py" and "postprocess.py" were corrected on March 27, 2024 to avoid confusions. - Finally, "Trained_models_and_results.zip" includes three folders and three files with suffix ".npy", and each folder corresponds to one file with suffix ".npy" with the same title. Each of the three folders include all trained models associated with one iLSTM model configuration (35 models for each configuration, details are described in the paper). Each file with suffix ".npy" includes the post-processed results of the corresponding 35 models under one iLSTM model configuration.

54 ENVIRONMENTAL SCIENCES↗

Cross-Validation of Computational and Experimental Distributed Surface Pressures on the Space Launch System

This paper presents a new workflow for comparing experimental pressure-sensitive paint (PSP) data to computational fluid dynamic (CFD) simulations by way of mapping data from corresponding grids utilizing interpolation methods. In addition to generating quantitative and qualitative point-to-point comparisons between PSP and CFD data, this workflow extracts sectional loading data from both grids and generates lineload comparison charts for corresponding PSP and CFD runs. Experimental PSP data presented in this paper were taken from a 2016 NASA Ames Research Center Unitary Plan Wind Tunnel 11- by 11-Foot Transonic WindTunnel Facility test of the NASA Space Launch System. CFD simulation data for comparison purposes were generated using the FUN3D code. Overall, interpolation onto PSP grids versus CFD grids yields comparable surface pressure fields. However, lineload comparisons are easier to make on the CFD grid-mapped data due to the grid topology and the current capabilities of the lineload analysis tools at NASA Langley Research Center. This workflow is written using contemporary software (Python, Tecplot, PyTecplot), is compatible with existing tools at NASA Langley, and is developed to be adaptable depending on the situation.

SLS↗

Analysis of H atoms in a negative ion source plasma with the non-equilibrium electron energy distribution function

In negative ion sources for the neutral beam injection, it is important to calculate H atom flux onto the plasma grid (PG) surface for the evaluation of H{sup -} production on the PG surface. We have developed a neutral (H{sub 2} molecules and H atoms) transport code. In the present study, the neutral transport code is applied to the analysis of the H{sub 2} and H transport in a NIFS-R and D ion source in order to calculate the flux onto the PG surface. Taking into account non-equilibrium feature of the electron energy distribution function (EEDF), i.e., the fast electron component, we have done the neutral transport simulation. The results suggest that the precise evaluation of the EEDF, especially in the energy range 15 eV < E < 30 eV is important for the dissociation rate of H{sub 2} molecules by the electron impact collision and the resultant H atom flux on the PG.

43 PARTICLE ACCELERATORS↗

Heat Transfer Computations of Internal Duct Flows With Combined Hydraulic and Thermal Developing Length

This study investigated the Navier-Stokes computations of the surface heat transfer coefficients of a transition duct flow. A transition duct from an axisymmetric cross section to a non-axisymmetric cross section, is usually used to connect the turbine exit to the nozzle. As the gas turbine inlet temperature increases, the transition duct is subjected to the high temperature at the gas turbine exit. The transition duct flow has combined development of hydraulic and thermal entry length. The design of the transition duct required accurate surface heat transfer coefficients. The Navier-Stokes computational method could be used to predict the surface heat transfer coefficients of a transition duct flow. The Proteus three-dimensional Navier-Stokes numerical computational code was used in this study. The code was first studied for the computations of the turbulent developing flow properties within a circular duct and a square duct. The code was then used to compute the turbulent flow properties of a transition duct flow. The computational results of the surface pressure, the skin friction factor, and the surface heat transfer coefficient were described and compared with their values obtained from theoretical analyses or experiments. The comparison showed that the Navier-Stokes computation could predict approximately the surface heat transfer coefficients of a transition duct flow.

Wang, C. R.↗

Fast physics-based launcher optimization for electron cyclotron current drive

With the increased urgency to design fusion pilot plants, fast optimization of electron cyclotron current drive (ECCD) launchers is paramount. Traditionally, this is done by coarsely sampling the 4D parameter space of possible launch conditions consisting of (1) the launch location (constrained to lie along the reactor vessel), (2) the launch frequency, (3) the toroidal launch angle, and (4) the poloidal launch angle. For each initial condition, a ray-tracing simulation is performed to evaluate the ECCD efficiency. Unfortunately, this approach often requires a large number of simulations (sometimes millions in extreme cases) to build up a dataset that adequately covers the plasma volume, which must then be repeated every time the design point changes. Here we adopt a different approach. Rather than launching rays from the plasma periphery and hoping for the best, we instead directly reconstruct the optimal ray for driving current at a given flux surface using a reduced physics model coupled with a commercial ray-tracing code. Repeating this throughout the plasma volume requires only hundreds of simulations, constituting a significant speedup. The new method is validated on two separate example tokamak profiles, and is shown to reliably drive localized current at the specified flux surface with the same optimal efficiency as obtained from the traditional approach.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

STREAM II-V5: REVISION OF STREAM II-V4 TO ACCOUNT FOR THE EFFECTS OF RAINFALL EVENTS

STREAM II-V4 is the aqueous transport module currently used by the Savannah River Site emergency response Weather Information Display (WIND) system. The transport model of the Water Quality Analysis Simulation Program (WASP) was used by STREAM II to perform contaminant transport calculations. WASP5 is a US Environmental Protection Agency (EPA) water quality analysis program that simulates contaminant transport and fate through surface water. STREAM II-V4 predicts peak concentration and peak concentration arrival time at downstream locations for releases from the SRS facilities to the Savannah River. The input flows for STREAM II-V4 are derived from the historical flow records measured by the United States Geological Survey (USGS). The stream flow for STREAM II-V4 is fixed and the flow only varies with the month in which the releases are taking place. Therefore, the effects of flow surge due to a severe storm are not accounted for by STREAM II-V4. STREAM II-V4 has been revised to account for the effects of a storm event. The steps used in this method are: (1) generate rainfall hyetographs as a function of total rainfall in inches (or millimeters) and rainfall duration in hours; (2) generate watershed runoff flow based on the rainfall hyetographs from step 1; (3) calculate the variation of stream segment volume (cross section) as a function of flow from step 2; (4) implement the results from steps 2 and 3 into the STREAM II model. The revised model (STREAM II-V5) will find the proper stream inlet flow based on the total rainfall and rainfall duration as input by the user. STREAM II-V5 adjusts the stream segment volumes (cross sections) based on the stream inlet flow. The rainfall based stream flow and the adjusted stream segment volumes are then used for contaminant transport calculations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Disordering and H-embrittlement of Pb(110) surface using embedded atom method and molecular dynamics

The dynamics and structure of the crystal melt interface are of great importance in crystal growth, melting, and other properties of the solid-liquid interface. The Embedded Atom Method (EAM), a semiempirical method developed by Daw and Baskes for determining the energetics of atoms in a bulk environment, is a useful method in the computer simulation. The EAM functions of PB in conjunction with the MD code are employed to study melting and disordering of the Pb(100) surface. The EAM functions are fitted to the bulk experimental data at zero temperature, and it is not clear if it will behave correctly at higher temperatures. In fact, it is shown that use of a similar type of potential at higher temperatures might result in a negative coefficient of thermal expansion. The primary purpose here is to perform MD simulation combined with the EAM functions of PB to study melting of the Pb(100) surface. This provides an accurate test of the EAM functions at higher temperatures. In particular, we calculate the two dimensional structure factor, the two dimensional distribution function, and density profile as a function of temperature up to the melting point of lead.

Karimi, Majid↗