Results for “wave guide” — Page 47

DOE OSTI2016

Investigation of a K-band large coaxial relativistic backward wave oscillator

A K-band large coaxial relativistic backward wave oscillator has been investigated by the 2.5-D particle-in-cell code. This device can generate high-power microwave at a constant frequency with a constant efficiency by increasing the radius of the electron beam and the average radius of the slow-wave structure. The simulation results show that the power conversion efficiency can reach 38.8% at the frequency of 25.48 GHz with the output power of 1.65 GW, while the electron beam has the energy of 196 kV and carries the current of 21.6 kA guided by the magnetic field of 2.5 T.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2017

Experimental demonstration of a 5th harmonic mm-wave frequency multiplying vacuum tube

Here, we report the experimental demonstration of a 5th harmonic mm-wave frequency multiplying vacuum electronic device, which uses an over-moded spherical sector output cavity. In this device, a pencil electron beam is helically deflected in a transverse deflecting cavity before entering the output cavity. No magnetic field is required to focus or guide the beam. We built and tested a proof-of-principle device with an output frequency of 57.12 GHz. The measured peak power was 52.67 W at the 5th harmonic of the drive frequency. Power at the 4th, 6th, and 7th harmonics was 33.28 dB lower than that at the 5th harmonic.

43 PARTICLE ACCELERATORS↗

NASA NTRS2004

White Light Modeling, Algorithm Development, and Validation on the Micro-arcsecond Metrology Testbed

The Space Interferometry Mission (SIM) scheduled for launch in early 2010, is an optical interferometer that will perform narrow angle and global wide angle astrometry with unprecedented accuracy, providing differential position accuracies of 1uas, and 4uas global accuracies in position, proper motion and parallax. The astrometric observations of the SIM instrument are performed via delay measurements provided by three Michelson-type, white light interferometers. Two 'guide' interferometers acquire fringes on bright guide stars in order to make highly precise measurements of variations in spacecraft attitude, while the third interferometer performs the science measurement. SIM derives its performance from a combination of precise fringe measurements of the interfered starlight (a few ten-thousandths of a wave) and very precise (tens of picometers) relative distance measurements made between a set of fiducials. The focus of the present paper is on the development and analysis of algorithms for accurate white light estimation, and on validating some of these algorithms on the MicroArcsecond Testbed.

metrology↗

DOE OSTI2022

Multiscale and multiphysics FEA simulation and materials optimization for laser ultrasound transducers

In this study, the relationship between the nanocomposite design and the laser ultrasound transducer (LUT) characteristics was investigated through simulations in multiple scale levels for material behavior, device response, and acoustic wave propagation in media. First, the effects of the nanoparticle size and concentration on the effective properties of composites were quantitatively investigated with the finite element analysis (FEA) method. Second, the effective properties of the nanocomposite were assigned to the layer, which is modeled as a homogeneous material, in the FEA for the LUT simulating the energy conversion from the incident laser to the acoustic wave. Finally, the ultrasound propagation in the water was calculated by a theoretical wave propagation model. The FEA-based prediction was compared with the experimental data in the literature and a theoretical analysis for LUT based on Thermal-Acoustic coupling. As a result, the ultrasound waves on the transducer surface and at a distance in the water could be predicted. Based on the hierarchically integrated prediction procedure, the optimal conditions of the photoacoustic nanocomposites were investigated through the parametric study with the particle size and concentration as variables. The results guide the material designs optimized for different device characteristics, such as high pressure and broad bandwidth.

36 MATERIALS SCIENCE↗

DOE OSTI2014

Inertial confinement fusion based on the ion-bubble trigger

Triggering the ion-bubble in an inertial confinement fusion, we have developed a novel scheme for the fast ignition. This scheme relies on the plasma cavitation by the wake of an intense laser pulse to generate an ion-bubble. The bubble acts both as an intense electron accelerator and as an electron wiggler. Consequently, the accelerated electrons trapped in the bubble can emit an intense tunable laser light. This light can be absorbed by an ablation layer on the outside surface of the ignition capsule, which subsequently drills it and thereby produces a guide channel in the pellet. Finally, the relativistic electron beam created in the bubble is guided through the channel to the high density core igniting the fusion fuel. The normalized beam intensity and beam energy required for triggering the ignition have been calculated when core is heated by the e-beam. In addition, through solving the momentum transfer, continuity and wave equations, a dispersion relation for the electromagnetic and space-charge waves has been analytically derived. The variations of growth rate with the ion-bubble density and electron beam energy have been illustrated. It is found that the growth rates of instability are significantly controlled by the ions concentration and the e-beam energy in the bubble.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1994

High-resolution imaging with a tip-tilt Cassegrain secondary

A prototype adaptive secondary mirror has been developed on a 2.3-m telescope to stabilize rapid motion caused by atmospheric turbulence. The instantaneous position of an image's centroid, or brightest speckle, is measured by a near-infrared camera system which enables the tip-tilt mirror to recenter the image. Correction is accomplished at closed-loop frequencies of less than or = 100 Hz on guide stars with K (2.2 micrometers) magnitudes less than or = 8. Image motion is reduced to less than 0.1 sec rms, removing over 90% of low-frequency (f less than or = 5 Hz) tilt power, leaving less than or = 1 rad exp 2 mean square wave front tilt phase error. In seeing conditions where D/r sub o approximately = 4, long exposures in the H band (1.6 micrometers) exhibit a nearly diffraction-limited resolution of 0.19 sec full width at half maximum (FWHM) (Strehl ratio aprroximately = 0.14)-a factor of 4 improvement over uncorrected images. Reduction of the present static optical errors will improve the Strehl ratio another factor of 2, leading to approximately 70% of the maximum possible Strehl ratio.

Close, L. M.↗

DOE OSTI2026

Ultrabroadband Spacetime Nanoscopy of Terahertz Polaritons in a van der Waals Cavity

Guiding, storing, and processing light at the nanoscale hinges on understanding how polaritons — hybrid quasiparticles of light and matter — propagate and interfere in both space and time. This work introduces a synchrotron-based technique, SYnchrotron SpaceTimE Mapping (SYSTEM), which captures real-time evolution of polariton wave packets with ∼10 nm spatial and sub-100 fs temporal resolution across an ultrabroadband 5–50 THz range. Here, SYSTEM directly visualizes the creation, interference, and decay of multiple high-quality Fabry-Pérot phonon polariton cavity modes in an α-MoO 3 microcavity. These real-space, real-time observations reveal wave-packet dynamics and cavity resonances with record-high quality factors (Q ≈ 100) in the single-digit terahertz regime near 9 THz. SYSTEM thus offers a powerful and broadly applicable platform for probing and engineering ultraslow, deeply subwavelength polaritons, opening new avenues for tailoring light–matter interactions and advancing next-generation THz nanophotonic technologies.

36 MATERIALS SCIENCE↗

DOE OSTI2015

Sphere-by-Sphere Manufacturing of 3D Microscale Granular Materials

Two of the central challenges in the mechanical design of components in nuclear systems are the dissipation of energy from external shocks and the localization of energy in energetic materials. This research seeks to address these problems by developing a patterned granular microstructure that can be optimized to direct or impede the transfer of energy carried by stress waves. Such structures require the development of a manufacturing technique that can yield perfectly ordered lattices. Two branches of research are detailed here: the development of a sphere-by-sphere additive manufacturing technique, and the development of a framework for modeling the technique in order to guide future improvements. Proof of concept of the method is demonstrated, and recommendations for future work are made.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1979

A new technique for measuring solar rotation

A new technique for measuring solar photospheric and subphotospheric rotation rates is described. The technique utilizes the standing-wave nature of the nonradial p-mode oscillations of the whole sun. Specifically, the technique is based upon the observed concentration of p-mode oscillatory power into well defined ridges in two-dimensional wavenumber-frequency power spectra. The frequencies of the ridges in the eastward- and westward-traveling portions of an individual spectrum are systematically shifted in opposite directions by a drift of the standing-wave pattern across the observing field of view. The magnitudes of these frequency shifts are related to the drift velocity and to the horizontal wavenumber in such a way that measurement of the observed frequency shifts in a spectrum yields the drift velocity for that observing run. By guiding on the solar limbs and observing the velocity field at disk center, the observed drift velocity obtained in this way is exactly the rotational velocity of the solar p-mode pattern, and of the solar gas itself.

Rhodes, E. J., Jr.↗

NASA NTRSDate not supplied

Development and Assessment of a New Particle Image Velocimetry System in the NASA GRC 225 cm2 Wind Tunnel

As part of an ongoing campaign to provide detailed and thorough measurements in a two-dimensional impinging shock-wave/boundary-layer interaction (SWBLI), a custom implementation of the Particle Image Velocimetry (PIV) measurement technique in the NASA Glenn 225 cm2 Wind Tunnel was constructed. The flow seeding apparatus was devised to locally seed the region of interest in the overall flowfield to avoid coating the viewing window with seed material. The ability of the PIV system to provide small particles which faithfully track the underlying gas-phase flowfield was of key importance for the success of this system to make quality measurements in the SWBLI flowfield. In order to optimize and assess the performance of the particle seeding system, PIV measurements were made across a planar oblique shock wave and particle response was analyzed to quantify the particle lag effects due to the finite inertia of the seed droplets. Video recordings from a camera placed in the wind tunnel plenum tank were also used to discern the near-field behavior of the seeded plume and guide the design evolution of the seeding apparatus. The resulting optimized seeding configuration was applied to make PIV measurements in the wind tunnel test section boundary layer to assess the seed particle spatial coverage and concentration. This sample boundary layer dataset provides an analog to the eventual boundary layer measurements to be made in the axisymmetric test section under much more challenged viewing conditions.

PIV↗

NASA NTRSDate not supplied

Development and Assessment of a New Particle Image Velocimetry System in the NASA GRC 225 cm2 Wind Tunnel

As part of an ongoing campaign to provide detailed and thorough measurements in a two-dimensional impinging shock-wave/boundary-layer interaction (SWBLI), a custom implementation of the Particle Image Velocimetry (PIV) measurement technique in the NASA Glenn 225 cm2 Wind Tunnel was constructed. The flow seeding apparatus was devised to locally seed the region of interest in the overall flowfield to avoid coating the viewing window with seed material. The ability of the PIV system to provide small particles which faithfully track the underlying gas-phase flowfield was of key importance for the success of this system to make quality measurements in the SWBLI flowfield. In order to optimize and assess the performance of the particle seeding system, PIV measurements were made across a planar oblique shock wave and particle response was analyzed to quantify the particle lag effects due to the finite inertia of the seed droplets. Video recordings from a camera placed in the wind tunnel plenum tank were also used to discern the near-field behavior of the seeded plume and guide the design evolution of the seeding apparatus. The resulting optimized seeding configuration was applied to make PIV measurements in the wind tunnel test section boundary layer to assess the seed particle spatial coverage and concentration. This sample boundary layer dataset provides an analog to the eventual boundary layer measurements to be made in the axisymmetric test section under much more challenged viewing conditions.

PIV↗

DOE OSTI2019

Instabilities and turbulence in low-$β$ guide field reconnection exhausts with kinetic Riemann simulations

The role of turbulence in low-$β$, guide-field reconnection exhausts is explored in 2D reconnection and 2D and 3D Riemann simulations. The structure of the exhaust and associated turbulence is controlled by a pair of rotational discontinuities (RDs) at the exhaust boundary and a pair of slow shocks (SSs) that are generated by counterstreaming ions beams. In 2D, the exhaust develops large-amplitude striations at the ion Larmor radius scale that are produced by electron-beam-driven ion cyclotron waves. The electron beams driving the instability are injected into the exhaust from one of the RDs. However, in 3D Riemann simulations, the additional dimension (in the out-of-plane direction) results in strong Buneman and electron-electron streaming instabilities at the RD which suppress the electron beam formation and therefore the striations in the exhaust. The strength of the streaming instabilities at the RD is controlled by the ratio of the electron thermal speed to Alfvén speed, with the lower thermal speed being more unstable. In the 3D simulations, an ion-ion streaming instability acts to partially thermalize the counterstreaming ion beams at the SSs. This instability is controlled by the ratio of the sound speed to Alfvén speed and is expected to be stable in the low $β$ solar corona. The results suggest that in a guide field reconnection exhaust with 1 $\gg$ $β >$ $m_e/m_i$, the kinetic-scale turbulence that develops will be too weak to play a significant role in energy conversion and particle acceleration. Therefore, the energy conversion will be mostly controlled by laminar physics or multi-x-line reconnection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Quasi‐Binary Transition Metal Dichalcogenide Alloys: Thermodynamic Stability Prediction, Scalable Synthesis, and Application

Abstract Transition metal dichalcogenide (TMDCs) alloys could have a wide range of physical and chemical properties, ranging from charge density waves to superconductivity and electrochemical activities. While many exciting behaviors of unary TMDCs have been demonstrated, the vast compositional space of TMDC alloys has remained largely unexplored due to the lack of understanding regarding their stability when accommodating different cations or chalcogens in a single‐phase. Here, a theory‐guided synthesis approach is reported to achieve unexplored quasi‐binary TMDC alloys through computationally predicted stability maps. Equilibrium temperature–composition phase diagrams using first‐principles calculations are generated to identify the stability of 25 quasi‐binary TMDC alloys, including some involving non‐isovalent cations and are verified experimentally through the synthesis of a subset of 12 predicted alloys using a scalable chemical vapor transport method. It is demonstrated that the synthesized alloys can be exfoliated into 2D structures, and some of them exhibit: i) outstanding thermal stability tested up to 1230 K, ii) exceptionally high electrochemical activity for the CO 2 reduction reaction in a kinetically limited regime with near zero overpotential for CO formation, iii) excellent energy efficiency in a high rate Li–air battery, and iv) high break‐down current density for interconnect applications. This framework can be extended to accelerate the discovery of other TMDC alloys for various applications.

Hemmat, Zahra↗

DOE OSTI2021

Enabling Marine Energy Integration for Ocean Observing: Functional Requirements

Marine renewable energy (i.e., wave, tidal or ocean current, thermal gradient, and salinity gradient) or MRE can revolutionize ocean observing capabilities. Five use cases representing a range of ocean observing platforms were developed based on end-user feedback. Drawing from these use cases, common needs or functional requirements were developed to help guide the integration of MRE power delivery for ocean observation structures and functions. The functional requirements were determined from descriptions of the use cases, specifications of hardware that are used or closely associated with existing ocean observation platforms, and direct feedback from ocean observation sensor/platform developers and users. Twenty types of functional requirements were identified, including those associated with power and energy use; physical system requirements; temperature and depth; electrical, acoustic, and motion interference; and reliability. Each set of functional requirements is illustrated as features of the use cases. By defining functional requirements for MRE technology integration in ocean observing platforms, and focusing on end-user requirements, barriers to developing MRE-driven ocean observation missions can be reduced.

50 EE - Wind and Water Power Program - Water (EE-4↗

NASA NTRS1979

Combined pressure and temperature distortion effects on internal flow of a turbofan engine

An additional data base for improving and verifying a computer simulation developed by an engine manufacturer was obtained. The multisegment parallel compressor simulation was designed to predict the effects of steady-state circumferential inlet total-pressure and total-temperature distortions on the flows into and through a turbofan compression system. It also predicts the degree of distortion that will result in surge of the compressor. The effect of combined 180 deg square-wave distortion patterns of total pressure and total temperature in various relative positions is reported. The observed effects of the combined distortion on a unitary bypass ratio turbofan engine are presented in terms of total and static pressure profiles and total temperature profiles at stations ahead of the inlet guide vanes as well as through the fan-compressor system. These observed profiles are compared with those predicted by the complex multisegment model. The effects of relative position of the two components comprising the combined distortion on the degree resulting in surge are discussed. Certain relative positions required less combined distortion than either a temperature or pressure distortion by itself.

Braithwaite, W. M.↗

NASA NTRS1993

Experimental verification of a theoretical model of an active cladding optical fiber fluorosensor

Experiments were conducted to verify a theoretical model on the injection efficiency of sources in the cladding of an optical fiber. The theoretical results predicted an increase in the injection efficiency for higher differences in refractive indices between the core and cladding. The experimental apparatus used consisted of a glass rod 50 cm long, coated at one end with a thin film of fluorescent substance. The fluorescent substance was excited with side illumination, perpendicular to the rod axis, using a 476 nm Argon-ion laser. Part of the excited fluorescence was injected into the core and guided to a detector. The signal was measured for several different cladding refractive indices. The cladding consisted of sugar dissolved in water and the refractive index was changed by varying the sugar concentration in the solution. The results indicate that the power injected into the rod, due to evanescent wave injection, increases with the difference in refractive index which is in qualitative agreement with theory.

Albin, Sacharia↗

DOE OSTI2020

Enabling Marine Energy Integration for Ocean Observing: Functional Requirements

Marine renewable energy (i.e., wave, tidal or ocean current, thermal gradient, and salinity gradient) or MRE can revolutionize ocean observing capabilities. Five use cases representing a range of ocean observing platforms were developed based on end-user feedback. Drawing from these use cases, common needs or functional requirements were developed to help guide the integration of MRE power delivery for ocean observation structures and functions. The functional requirements were determined from descriptions of the use cases, specifications of hardware that are used or closely associated with existing ocean observation platforms, and direct feedback from ocean observation sensor/platform developers and users. Twenty types of functional requirements were identified, including those associated with power and energy use; physical system requirements; temperature and depth; electrical, acoustic, and motion interference; and reliability. Each set of functional requirements is illustrated as features of the use cases. By defining functional requirements for MRE technology integration in ocean observing platforms, and focusing on end-user requirements, barriers to developing MRE-driven ocean observation missions can be reduced.

Cavagnaro, Robert J.↗

DOE OSTI2024

Dynamic control of the spatial frequency content of an intense laser via intra-beam energy transfer

We present theory and simulations demonstrating that bandwidth-inducing optical smoothing techniques such as smoothing by spectral dispersion (SSD) can initiate intra-beam energy transfer (IBET) within a single beam. IBET consists of energy transfer between the different frequency components of the beam and results in a simultaneous and correlated redistribution of the temporal and spatial frequencies of the laser's electric field. We identify a threshold in bandwidth for IBET to occur and validate the theory with simulations. The bandwidth and the color cycling of SSD can result in IBET in conditions relevant for high-energy density experiments at the National Ignition Facility and Omega Laser. We show that IBET could be used to manipulate a laser's spatial frequency content within a plasma. In particular, this technique could be used to increase a laser's effective f-number, with potential applications for self-guiding in plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗