Search NASA⌕ Search

SEARCH · Search NASA

Results for “ACOUSTIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Single stage, low noise advanced technology fan. Volume 3: Acoustic design

The acoustic design for a half-scale fan vehicle, which would have application on an advanced transport aircraft, is described. The single stage advanced technology fan was designed to a pressure ratio of 1.8 at a tip speed of 503 m/sec (1,650 ft/sec). The two basic approaches taken in the acoustic design were: (1) minimization of noise at the source, and (2) suppression of the generated noise in the inlet and bypass exhaust duct. Suppression of the generated noise is accomplished in the inlet through use of the hybrid concept (wall acoustic treatment plus airflow acceleration suppression) and in the exhaust duct with extensive acoustic treatment including a splitter. The goal of the design was attainment of twenty effective perceived noise decibels (20 EPNdB) below current Federal Air Regulation noise standards for a full-scale fan at the takeoff, cutback, and approach conditions. Predicted unsuppressed and suppressed fore and aft maximum perceived noise levels indicate that the cutback condition is the most critical with respect to the goal, which is probably unattainable for that condition. This is also true for aft radiated noise in the approach condition.

Kazin, S. B.↗

Single stage, low noise, advanced technology fan. Volume 5: Fan acoustics. Section 1: Results and analysis

The acoustic tests and data analysis for a 0.508-scale fan vehicle of a 111,300 newton (25,000 pound) thrust, full-size engine, which would have application on an advanced transport aircraft, is described. The single-stage advanced technology fan was designed to a pressure ratio of 1.8 at a tip speed of 503 m/sec (1,650 ft/sec) to achieve the desired pressure ratio in a single-stage fan with low radius ratio (0.38), and to maintain adequate stall margin. The fan has 44 tip-shrouded rotor blades and 90 outlet guide vanes. The two basic approaches taken in the acoustic design were: (1) minimization of noise at the source, and (2) suppression of the generated noise in the inlet and bypass exhaust duct. Suppression of the generated noise was accomplished in the inlet through use of the hybrid concept (wall acoustic treatment plus airflow acceleration suppression) and in the exhaust duct with extensive acoustic treatment including a splitter. The goal of the design was attainment of twenty effective perceived noise decibels (20 EPNdB) below current Federal Air Regulation noise standards for a full-scale fan at the takeoff, cutback, and approach conditions. The suppression goal of FAR 36-20 was not reached, but improvements in the technology of both front and aft fan-noise suppression were realized. The suppressed fan noise was shown to be consistent with the proposed federal regulation on aircraft noise.

Jutras, R. R.↗

Propagation of acoustic modes in the transitional ionosphere

Continuum theory is unsatisfactory for describing wave propagation in the transitional ionosphere, since the mean free path is of the same order as the characteristic length (i.e., Knudsen number in this region is of the order of unity). Therefore a transition model in which isotropic electrons behave as a fluid while the ions are governed by the kinetic equation modified by ion-electron collision effects is proposed to study acoustic wave propagation in the upper atmosphere in the altitude region from 500 to 2000 km. The results show that the dissipation of acoustic waves by electrons is through the viscous and thermal conduction effects, and the dissipation of acoustic waves by ions is through Landau damping. Comparisons of the characteristics of acoustic mode propagation and wave dissipation mechanisms in the collision-dominated, transitional from collisional to collisionless, and collisionless media are also discussed.

Hung, R. J.↗

Reduction of noise from a fan stage for a turbofan engine by use of long-chord acoustically-treated stator vanes

A set of acoustically-treated long-chord vanes was designed to replace the vanes in an existing fan stage to investigate the noise reduction possibilities of both increased stator chord length and this method of incorporating acoustic damping material. The vanes were tested with both active and inactive acoustic surfaces. The inactive tests showed significant broadband noise effects with noise reductions in the middle to high frequencies and an increase at low frequencies. No reduction in blade passage tone was observed, but decreases in the overtones were observed. The tests with the active acoustic treatment showed large noise reductions over a wide frequency range.

Dittmar, J. H.↗

Design of optimum acoustic treatment for rectangular ducts with flow

A design optimization technique for acoustic treatment in rectangular ducts with uniform mean flow is presented. The technique is based on the acoustic wave solution in terms of series of characteristic duct modes. The analysis allows multiple axial treatment sections along the length of the duct and requires a known modal characterization of the sound source. Conditions of acoustic pressure and acoustic velocity continuity are used to match modal solutions at planes of impedance discontinuity in the duct. Experimental techniques for obtaining this modal characterization are presented. Using duct modes measured at the source plane, the optimization technique is exercised to design an optimized single element liner in a case without mean flow, and optimized single and dual element liners in cases with mean flow. The validity of the program for predicting noise suppression is demonstrated by comparing analytical predictions with measured data for several (non-optimum) cases. Application to treatment design in turbomachinery exhaust ducts is considered.

Motsinger, R. E.↗

Aeroacoustics: Fan noise and control; Duct acoustics; Rotor noise

The recent progress in duct acoustic research is reflected by fourteen papers which cover essentially the areas of linear duct acoustics, the characteristics of absorbent materials, and nonlinear duct acoustics. With respect to propagation in ducts, emphasis is placed on computational methods aimed at attaining effective economical modeling of propagation in variable-geometry and in hard-wall or soft-wall ducts. Computational methods developed to reduce computer processing and storage requirements are outlined, along with a wave envelope technique for reducing processing and storage needs. The latter technique is applied to the optimum segmented acoustic duct linear design. A finite difference technique is used in combination with conformal mapping to compute the optimum multisection duct linear design.

Schwartz, I. R.↗

Influence of acoustics in separation processes

The effects of introducing high energy acoustics into various filtering and drying systems were studied. With very slow velocity filtration systems, it was found that the introduction of acoustics could substantially increase the flow rate and also aided in the coagulation of the particulates before reaching the filter media. In the drying of temperature sensitive powders, the rate was increased by the introduction of acoustics. The acoustic frequency used was 20 kHz with power levels up to 3 watts per square centimeter.

Fairbanks, H. V.↗

Pulse analysis of acoustic emission signals

A method for the signature analysis of pulses in the frequency domain and the time domain is presented. Fourier spectrum, Fourier transfer function, shock spectrum and shock spectrum ratio were examined in the frequency domain analysis, and pulse shape deconvolution was developed for use in the time domain analysis. Comparisons of the relative performance of each analysis technique are made for the characterization of acoustic emission pulses recorded by a measuring system. To demonstrate the relative sensitivity of each of the methods to small changes in the pulse shape, signatures of computer modeled systems with analytical pulses are presented. Optimization techniques are developed and used to indicate the best design parameters values for deconvolution of the pulse shape. Several experiments are presented that test the pulse signature analysis methods on different acoustic emission sources. These include acoustic emissions associated with: (1) crack propagation, (2) ball dropping on a plate, (3) spark discharge and (4) defective and good ball bearings. Deconvolution of the first few micro-seconds of the pulse train are shown to be the region in which the significant signatures of the acoustic emission event are to be found.

Houghton, J. R.↗

Constitutive acoustic-emission elastic-stress behavior of magnesium alloy

Repeated laoding and unloading of a magnesium alloy below the macroscopic yield stress result in continuous acoustic emissions which are generally repeatable for a given specimen and which are reproducible between different specimens having the same load history. An acoustic emission Bauschinger strain model is proposed to describe the unloading emission behavior. For the limited range of stress examined, loading and unloading stress delays of the order of 50 MN/sq m are observed, and they appear to be dependent upon the direction of loading, the stress rate, and the stress history. The stress delay is hypothesized to be the manifestation of an effective friction stress. The existence of acoustic emission elastic stress constitutive relations is concluded, which provides support for a previously proposed concept for the monitoring of elastic stresses by acoustic emission.

Williams, J. H., Jr.↗

Acoustic source location in the secondary mixing region of a jet-blown flap using a cross-correlation technique

An experimental investigation of the acoustic sources in the secondary mixing region of a laboratory-scale jet-flap was made using a causality correlation technique. The processed signal of a hot-film anemometer probe was cross correlated with the output signal of a far-field microphone. Axial acoustic source strength distributions were measured for three far-field microphone locations: plus or minus 45 deg in the flyover plane and 45 deg in the sideline plane. These measurements showed that the acoustic sources in the secondary mixing region are highly directional, radiating much more effectively to the -45 deg-microphone, located below the plane of the flap surface. A relative maximum in the acoustic source strength measured for the microphones in the flyover plane occurred very near the flap trailing edge, which may be due to an edge amplification effect predicted by the theoretical work of Ffowcs Williams and Hall.

Becker, R. S.↗

Pulse analysis of acoustic emission signals

A method for the signature analysis of pulses in the frequency domain and the time domain is presented. Fourier spectrum, Fourier transfer function, shock spectrum and shock spectrum ratio were examined in the frequency domain analysis and pulse shape deconvolution was developed for use in the time domain analysis. Comparisons of the relative performance of each analysis technique are made for the characterization of acoustic emission pulses recorded by a measuring system. To demonstrate the relative sensitivity of each of the methods to small changes in the pulse shape, signatures of computer modeled systems with analytical pulses are presented. Optimization techniques are developed and used to indicate the best design parameter values for deconvolution of the pulse shape. Several experiments are presented that test the pulse signature analysis methods on different acoustic emission sources. These include acoustic emission associated with (a) crack propagation, (b) ball dropping on a plate, (c) spark discharge, and (d) defective and good ball bearings. Deconvolution of the first few micro-seconds of the pulse train is shown to be the region in which the significant signatures of the acoustic emission event are to be found.

Houghton, J. R.↗

Acoustic design of the QCSEE propulsion systems

Acoustic design features and techniques employed in the Quiet Clean Short-Haul Experimental Engine (QCSEE) Program are described. The role of jet/flap noise in selecting the engine fan pressure ratio for powered lift propulsion systems is discussed. The QCSEE acoustic design features include a hybrid inlet (near-sonic throat velocity with acoustic treatment); low fan and core pressure ratios; low fan tip speeds; gear-driven fans; high and low frequency stacked core noise treatment; multiple-thickness treatment; bulk absorber treatment; and treatment on the stator vanes. The QCSEE designs represent and anticipated acoustic technology improvement of 12 to 16 PNdb relative to the noise levels of the low-noise engines used on current wide-body commercial jet transport aircraft.

Loeffler, I. J.↗

Applications of velocity potential function to acoustic duct propagation and radiation from inlets using finite element theory

A finite element velocity potential program was developed to study acoustic wave propagation in complex geometries. For irrotational flows, relatively low sound frequencies, and plane wave input, the finite element solutions showed significant effects of inlet curvature and flow gradients on the attenuation of a given acoustic liner in a realistic variable area turbofan inlet. The velocity potential approach can not be used to estimate the effects of rotational flow on acoustic propagation, since the potential acoustic disturbances propagate at the speed of the media in sheared flow. Approaches are discussed that are being considered for extending the finite element solution to include the far field, as well as the internal portion of the duct. A new matrix partitioning approach is presented that can be incorporated in previously developed programs to allow the finite element calculation to be marched into the far field. The partitioning approach provided a large reduction in computer storage and running times.

Baumeister, K. J.↗

An acoustic emission study of plastic deformation in polycrystalline aluminium

Acoustic emission experiments were performed on polycrystalline and single crystal 99.99% aluminum while undergoing tensile deformation. It was found that acoustic emission counts as a function of grain size showed a maximum value at a particular grain size. Furthermore, the slip area associated with this particular grain size corresponded to the threshold level of detectability of single dislocation slip events. The rate of decline in acoustic emission activity as grain size is increased beyond the peak value suggests that grain boundary associated dislocation sources are giving rise to the bulk of the detected acoustic emissions.

Bill, R. C.↗

An experimental investigation of acoustic radiation from a source inside a large turbulent free jet

An experiment has been conducted in NASA Langley's free-jet anechoic facility to assess the effect of a free-jet shear layer on sound radiation from an acoustic source placed inside the jet. The nozzle diameter was 1.22 m and operated at an exit velocity of 35 m/s. Two different types of sources were used; one was a compact source with a nearly uniform radiation pattern, the other was a noncompact source with highly directional radiation pattern. The acoustic source was driven by pure tone and 1/3-octave band white noise. Acoustic measurements were made both inside the jet flow in the potential core region and outside the jet in the acoustic farfield. The effects of mean flow convection and mean shear refraction on sound radiation were determined. The experimental results compared favorably with analytical predictions. The effect of free-jet turbulence on sound scattering was found to be insignificant.

Ozkul, A.↗

A comparison of linear acoustic theory with experimental noise data for a small-scale hovering rotor

Linear acoustic calculations based on full aerodynamic data as input are presented and compared with measured cases reported by Boxwell et al. (1978). The full aerodynamic data are obtained using three programs giving radial loading, chordwise loading, and chordwise position of transition. It is shown that in the theoretical results the most significant noise source mechanism is due to blade thickness. Thus the conclusions of Boxwell et al. as to the importance of nonlinearities around the blades are upheld. These conclusions concern the width, shape and the level of the acoustic pressure calculated from linear acoustic theory. Some of the approximations involved in the application of acoustic analogy using quadrupole sources are discussed. It is necessary that the near- and far-field problems of rotating blades be treated together as shown for the case of an oscillating sphere.

Farassat, F.↗

Applications of velocity potential function to acoustic duct propagation and radiation from inlets using finite element theory

A finite element velocity potential program has been developed to study acoustic wave propagation in complex geometries. For irrotational flows, relatively low sound frequencies, and plane wave input, the finite element solutions show significant effects of inlet curvature and flow gradients on the attenuation of a given acoustic liner in a realistic variable area turbofan inlet. In addition, as shown in the paper, the velocity potential approach can not be used to estimate the effects of rotational flow on acoustic propagation since the potential acoustic disturbances propagate at the speed of the media in sheared flow. Approaches are discussed that are being considered for extending the finite element solution to include the far field as well as the internal portion of the duct. A new matrix partitioning approach is presented that can be incorporated in previously developed programs to allow the finite element calculation to be marched into the far field. The partitioning approach provides a large reduction in computer storage and running times.

Baumeister, K. J.↗

Acoustic energy in ducts - Further observations

The transmission of acoustic energy in uniform ducts carrying uniform flow is investigated with the purpose of clarifying two points of interest. The two commonly used definitions of acoustic 'energy' flux are shown to be related by a Legendre transformation of the Lagrangian density exactly as in deriving the Hamiltonian density in mechanics. In the acoustic case the total energy density and the Hamiltonian density are not the same which accounts for two different 'energy' fluxes. When the duct has acoustically absorptive walls neither of the two flux expressions gives correct results. A reevaluation of the basis of derivation of the energy density and energy flux provides forms which yield consistent results for soft walled ducts.

Eversman, W.↗