Search NASA⌕ Search

SEARCH · Search NASA

Results for “Inverter Controls”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Ground surface temperature reconstructions: Using in situ estimates for thermal conductivity acquired with a fiber-optic distributed thermal perturbation sensor

We have developed a borehole methodology to estimate formation thermal conductivity in situ with a spatial resolution of one meter. In parallel with a fiber-optic distributed temperature sensor (DTS), a resistance heater is deployed to create a controlled thermal perturbation. The transient thermal data is inverted to estimate the formation's thermal conductivity. We refer to this instrumentation as a Distributed Thermal Perturbation Sensor (DTPS), given the distributed nature of the DTS measurement technology. The DTPS was deployed in permafrost at the High Lake Project Site (67 degrees 22 minutes N, 110 degrees 50 minutes W), Nunavut, Canada. Based on DTPS data, a thermal conductivity profile was estimated along the length of a wellbore. Using the thermal conductivity profile, the baseline geothermal profile was then inverted to estimate a ground surface temperature history (GSTH) for the High Lake region. The GSTH exhibits a 100-year long warming trend, with a present-day ground surface temperature increase of 3.0 {+-} 0.8 C over the long-term average.

54 ENVIRONMENTAL SCIENCES↗

Light scattering under conditions of nonstationary electromagnetically induced transparency

The propagation of probe radiation pulses in ultracold atomic ensembles is studied theoretically under conditions of electromagnetically induced transparency. The pulse 'stopping' process is considered which takes place upon nonadiabatic switching off and subsequent switching on the control field. We analysed the formation of an inverted recovered probe radiation pulse, i.e. the pulse propagating in the direction opposite to the propagation direction before the pulse stopping. Based on this analysis, a scheme is proposed for lidar probing atomic or molecular clouds in which the probe pulse penetrates into a cloud over the specified depth, while information on the cloud state is obtained from the parameters of the inverted pulse. Calculations are performed for an ensemble of {sup 87}Rb atoms. (fifth seminar in memory of d.n. klyshko)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Impedance Modeling and Stability Analysis for the PLL-less and Voltage Sensor-less Grid-tied Converters

The newly developed control methodology, which omits the phase-locked loop (PLL) and voltage sensor, has garnered considerable attention for its rapid dynamic response and reduced hardware expenses. Nonetheless, its stability concerns have not yet been thoroughly scrutinized. In this paper, the impedance modeling of the PLL-less and voltage sensorless control strategy has been established. The impedance model has been contrasted with the traditional PLL-based control scheme. Our findings demonstrate that the PLL-less and voltage sensorless control approach lacks the negative resistance behavior that is frequently observed in the traditional scheme, which results in unstable operations. Furthermore, the role of virtual resistance has been examined. To substantiate the aforementioned findings, simulation results are presented.

24 POWER TRANSMISSION AND DISTRIBUTION↗

A Generic and Multifunctional Electromagnetic Transient Model for Grid-Following Inverters

This paper presents a generic and multifunctional electromagnetic transient (EMT) dynamic model of grid-following (GFL) inverter-based resources (IBRs) using the PSCAD software platform. The features of the model include flexibility in selecting various types and combinations of DC sources covering photovoltaic modules, battery modules, and ideal DC-source modules as well as flexibility in selecting either switching or averaged models of the inverter. This model also covers exhaustive lists of controller algorithm, including open-loop/closed-loop PQ dispatch control, DC voltage and AC terminal voltage control, and conventional current control designed in the dq-domain, the ..alpha....beta.. -domain, and the positive-/negative-sequence domain. Moreover, this model is equipped with flexibility in selecting various types of current-limiting schemes, including saturation-based and latching-based current limiters, and anti-windup protection. Also, the EMT model is agnostic to the MVA rating and is suitable for interfacing transmission systems by complying with IEEE Std. 2800. The generality in the power circuits and the multifunctional options in the operation and control of the developed EMT model make it suitable for both academia and industry to study various power system aspects, including, but not limited to, the fault behavior of GFL IBRs, the impacts on the protection system, and the transient stability of a system interfaced with large numbers of GFL IBRs.

integrated circuit modeling↗

Fuel Cell Inverter Dataset

This data set contains the three phase AC voltage, three phase AC current, DC voltage and DC current. These data sets were captured during fuel cell inverter operation in grid-connected dispatch, islanded load changes, transition from grid-connected mode to islanded mode and vice-versa.

25 ENERGY STORAGE↗

Cold startup and low temperature performance of the Brayton cycle electrical subsystem

Cold performance tests and startup tests were conducted on the Brayton-cycle inverter, motor-driven pump, dc supply, speed control with parasitic load resistor and the Brayton control system. These tests were performed with the components in a vacuum and mounted on coldplates. A temperature range of ?25 to -50 C was used for the tests. No failures occurred, and component performance gave no indication that there would be any problem with the safe operation of the Brayton power generating system.

Vrancik, J. E.↗

Experimental and Theoretical Results in Output-Trajectory Redesign for Flexible Structures

In this paper we study the optimal redesign of output trajectory for linear invertible systems. This is particularly important for tracking control of flexible structures because the input-state trajectories that achieve the required output may cause excessive vibrations in the structure. A trade-off is then required between tracking and vibrations reduction. We pose and solve this problem as the minimization of a quadratic cost function. The theory is developed and applied to the output tracking of a flexible structure and experimental results are presented.

Dewey, J. S.↗

Experimental and Theoretical Results in Output Trajectory Redesign for Flexible Structures

In this paper we study the optimal redesign of output trajectories for linear invertible systems. This is particularly important for tracking control of flexible structures because the input-state trajectores, that achieve tracking of the required output may cause excessive vibrations in the structure. We pose and solve this problem, in the context of linear systems, as the minimization of a quadratic cost function. The theory is developed and applied to the output tracking of a flexible structure and experimental results are presented.

Dewey, J. S.↗

Free-Spinning-Tunnel Tests of a 1/16-Scale Model of the Chance Vought XF5U-1 Airplane, TED No. NACA 2349

Spin tests of a 1/16-scale model of the Chance Vought XF5U-1 airplane have been performed in the Langley 20-foot free-spinning tunnel. The effect of control position and movement upon the erect and inverted spin and recovery characteristics ae well as the effects of propellers, of stability flaps, and of various revisions to the design configuration have been determined for the normal fighter loading. The investigation also included spin recovery parachute, tumbling, and pilot-escape tests. For the original design configuration, with or without windmilling propellers, the recovery characteristics of the model were considered unsatisfactory. Increasing the maximum upward deflection of the ailavators from 45 deg to 65 deg resulted in greatly improved recovery characteristics. Dimensional revisions to the original airplane configuration, which satisfactorily improved the general spin and recovery characteristics of the model, consisted of: (1) a supplementary vertical tail 34 inches by 59 inches (full-scale) attached to a boom 80 inches aft of the trailing edge of the airplane in the plane of symmetry, (2) a large semispan undersurface spoiler placed along the airplane quarter-chord line and opened on the outboard side in a spin, or (3) two additional vertical tails 64 inches by 52 inches (full-scale) located at the tips of the ailavators. A satisfactory parachute arrangement for emergency spin recovery from demonstration spins was found to be an arrangement consisting of a 13.3-foot parachute attached by a 30-foot towline to the arresting gear mast on the airplane and opened simultaneously with an 8-foot parachute on the outboard end of the wing attached by a 3-foot towline. Tests indicated that pilot escape from a spin would be extremely hazardous unless the pilot is mechanically ejected from the cockpit. Model tumbling tests indicated that the airplane would not tumble.

White, Richard P.↗

Free-Spinning-Tunnel Tests of a 1/24-Scale Model of the McDonnell XP-88 Airplane with a VEE Tail

An investigation of the spin and recovery characteristics of a 1/24-scale model of the McDonnell XP-88 airplane has been conducted in the Langley 20-ft free-spinning tunnel. Results of tests with a conventional tail have been previously reported; the results presented herein are for the model with a vee tail installed. The effects of control settings and movements on the erect and inverted spin and recovery characteristics of the model. In the normal loading were determined. Tests of the model in the long-range loading also were made. The investigation included leading-edge-flap, spin-recovery-parachute, and rudder-pedal-force tests. The recovery characteristics of the model were satisfactory for the normal loading. Deflecting the leading-edge flaps improved recoveries. The results indicated that with the external wing tanks installed (long-range loading) recoveries may be poor and, therefore, if a spin is inadvertently entered in this condition the tanks should be jettisoned if recovery does not appear imminent immediately after it is attempted. A 10-foot spin-recovery tail parachute with a towline 40 feet long and a drag coefficient of 0.63 was found to be effective for spin recovery. The rudder pedal force required for spin recovery was indicated to be within the capabilities of the pilot.

Berman, Theodore↗

Free-Spinning-Tunnel Tests of a 1/24-Scale Model of the McDonnell XP-88 Airplane with a Conventional Tail

An investigation of the spin and recovery characteristics of a 1/24-scale model of the McDonnell XP-88 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements on the erect and inverted spin and recovery characteristics of the model in the normal loading were determined. Tests of the model in the long-range loading also were made. The investigation included tail-modification, spin-recovery parachute, pilot-escape, and rudder-pedal-force tests. Recoveries were generally satisfactory for spins in the normal loading provided the ailerons were not held against the spin. Satisfactory recoveries were obtained regardless of the aileron setting when the leading-edge flaps were deflected and normal recovery technique was used or when the horizontal tail was raised 70 inches, full scale. Recoveries were rapid from all inverted spins obtained. In the long-range loading with tanks on, it may be necessary to jettison the tanks in order to obtain recovery. A 12.0-foot spin-recovery parachute at the tail or a 4.0-foot parachute opened on the outer wing tip (drag coefficient of 0.66) was found to be effective for recoveries from demonstration spins. Test results showed that in an emergency the pilot should attempt to escape from the outboard side of the spinning airplane. The rudder-pedal forces in a spin were indicated to be within the capabilities of the pilot.

Berman, Theodore↗

Free-Spinning Tunnel Tests of a 1/24-Scale Model of the Grumman XTB3F-1 Airplane, TED No. NACA DE304

In accordance with a request of the Bureau of Aeronautics, Navy Department, tests were performed in the Langley 20-foot free-spinning tunnel to determine the spin and recovery characteristics of a 1/24 scale model of the Grumman XTB3F-1 airplane. The airplane is a two-place, midwing torpedo bomber equipped with a tractor propeller and an auxiliary jet engine. The effect of control setting and movement on the erect and inverted spin and recovery characteristics of the model were determined for the normal loading. Brief tests with mass extended slightly along the fuselage were also made, however, in order to determine the effect of such a mass variation on elevator effectiveness. Tests were performed to determine the size of emergency spin-recovery tail and wing-tip parachutes required for satisfactory recovery by parachute action alone. The investigation also included emergency pilot-escape tests and tests to determine the rudder pedal and elevator stick forces necessary to move the rudder and elevator for recovery.

Berman, Theodore↗

Free-Spinning-Tunnel Tests of a 1/24-Scale Model of the North American XP-86 Airplane

A spin investigation has been conducted in the Langley 20-foot free-spinning tunnel on a 1/24-scale model of the North American XP-86 airplane. The effects of control settings and movements upon the erect and inverted spin and recovery characteristics of the model were determined for the design gross weight loading. The long-range loading was also investigated and the effects of extending slats and dive flaps were determined. In addition, the investigation included the determination of the size of spin-recovery parachute required for emergency recovery from demonstration spins, the rudder force required to move the rudder for recovery, and the best method for the pilot to escape if it should become necessary to do so during a spin. The results of the investigation indicated that the XP-86 airplane will probably recover satisfactorily from erect and inverted spins for all possible loadings. It was found that fully extending both slats would be beneficial but that extending the dive brakes would cause unsatisfactory recoveries. It was determined that a 10.0-foot-diameter tail parachute with a drag coefficient of 0.7 and with a towline 30.0 feet long attached below the jet exit or a 6.0-foot-diameter wingtip parachute opened on the outer wing tip with a towline 6.0 feet long would insure recoveries from any spins obtainable. The rudder-pedal force necessary to move the rudder for satisfactory recovery was found to be within the physical capabilities of the pilot.

Berman, Theodore↗

Free-Spinning-Tunnel Investigation of a 1/25-Scale Model of the McDonnell F3H-1N Airplane, TED No. NACA AD 3100

An investigation was conducted in the Langley 20-foot free-spinning tunnel on a 1/23-scale model of the McDonnell F3H-1N airplane. The effects of control settings and movements upon the erect and inverted spin and recovery characteristics of the model were determined for the clean condition. Spin-recovery parachute tests were also performed. The results indicated that erect spins obtained on the airplane for the take-off or combat loadings should be satisfactorily terminated if full rudder reversal is accompanied by moving the ailerons to full with the spin (stick full right in a right spin). The spins obtained should be oscillatory in pitch, roll, and yaw. Recoveries from inverted spins should be satisfactory by full reversal of the rudder. A 16.7-foot- diameter tail parachute with a towline length of 30 feet and a drag coefficient of 0.734 should be adequate for emergency recovery from demonstration spins.

Lee, Henry A.↗

Capacitive Trans-Impedance Amplifier Circuit with Charge Injection Compensation

A capacitive trans-impedance amplifier circuit with charge injection compensation is provided. A feedback capacitor is connected between an inverting input port and an output port of an amplifier. A MOS reset switch has source and drain terminals connected between the inverting input and output ports of the amplifier, and a gate terminal controlled by a reset signal. The reset switch is open or inactive during an integration phase, and closed or active to electrically connect the inverting input port and output port of the amplifier during a reset phase. One or more compensation capacitors are provided that are not implemented as gate oxide or MOS capacitors. Each compensation capacitor has a first port connected to a compensation signal that is a static signal or a toggling compensation signal that toggles between two compensation voltage values, and a second port connected to the inverting input port of the amplifier.

Milkov, Mihail M.↗

Nanoscale molecularly imprinted polymers and method thereof

Nanoscale molecularly imprinted polymers (MIP) having polymer features wherein the size, shape and position are predetermined can be fabricated using an xy piezo stage mounted on an inverted microscope and a laser. Using an AMF controller, a solution containing polymer precursors and a photo initiator are positioned on the xy piezo and hit with a laser beam. The thickness of the polymeric features can be varied from a few nanometers to over a micron.

36 MATERIALS SCIENCE↗