Search NASA⌕ Search

SEARCH · Search NASA

Results for “LIGNITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Underground coal gasification using oxygen and steam

In this paper, through model experiment of the underground coal gasification, the effects of pure oxygen gasification, oxygen-steam gasification, and moving-point gasification methods on the underground gasification process and gas quality were studied. Experiments showed that H{sub 2} and CO volume fraction in product gas during the pure oxygen gasification was 23.63-30.24% and 35.22-46.32%, respectively, with the gas heating value exceeding 11.00 MJ/m{sup 3}; under the oxygen-steam gasification, when the steam/oxygen ratio stood at 2: 1, gas compositions remained virtually stable and CO + H{sub 2} was basically between 61.66 and 71.29%. Moving-point gasification could effectively improve the changes in the cavity in the coal seams or the effects of roof inbreak on gas quality; the ratio of gas flowing quantity to oxygen supplying quantity was between 3.1:1 and 3.5:1 and took on the linear changes; on the basis of the test data, the reasons for gas quality changes under different gasification conditions were analyzed.

01 COAL, LIGNITE, AND PEAT↗

Transformations and affinities for sulfur of Chinese Shenmu coal ash in a pulverized coal-fired boiler

The self-desulfurization efficiency of Shenmu coal with a high initial Ca/S molar ratio of 2.02 was measured in a 1,025 t/h pulverized coal-fired boiler. It increases from 29% to 32% when the power capacity decreases from 100% to 70%. About 60% of the mineral matter and calcium element fed into the furnace is retained in the fly ash, while less than 10% is retained in the bottom ash. About 70% of the sulfur element fed into the furnace is emitted as SO{sub 2} in the flue gas, while less than 10% is retained in the fly ash and less than 1% is retained in the bottom ash. The mineralogical compositions of feed coal, fly ash, and bottom ash were obtained by X-ray diffraction analysis. It is found that the initial amorphous phase content is 91.17% and the initial CaCO{sub 3} phase content is 2.07% in Shenmu coal. The vitreous phase and sulfation product CaSO{sub 4} contents are, respectively, 70.47% and 3.36% in the fly ash obtained at full capacity, while the retained CaCO{sub 3} and CaO contents are, respectively, 4.73% and 2.15%. However, the vitreous phase content is only 25.68% and no CaSO{sub 4} is detected in the bottom ash obtained at full capacity. When the power capacity decreases from 100% to 70%, the vitreous phase content in fly ash decreases from 70.47% to 67.41% and that in bottom ash increases from 25.68% to 28.10%.

01 COAL, LIGNITE, AND PEAT↗

Selective enrichment of phenols from coal liquefaction oil by solid phase extraction method

This study focuses on the solid phase extraction method for the enrichment and separation of phenol from coal liquefaction oil. The phenols' separation efficiency was compared on different solid phase extraction (SPE) cartridges, and the effect of solvents with different polarity and solubility parameter on amino-bonded silica was compared for selection of optimal elution solution. The result showed that amino-bonded silica has the highest selectivity and best extraction capability due to two factors, weak anion exchange adsorption and polar attraction adsorption.

01 COAL, LIGNITE, AND PEAT↗

Effect of hydrogen bond on coal extraction by in-situ vacuum FTIR

Coal chemical formation environment might result in different properties of hydrogen bonds in coal structure. The thermo stability, amount and types of hydrogen bond in six typical Chinese coal macerals were investigated by in situ vacuum Fourier transform infrared spectroscopy (FTIR). It was found that three types of hydrogen bond were involved in coal structure, which were OH-N, OH self associated, and OH tetrapolymer hydrogen bond. There was no correlation between the amount of three types of hydrogen bonds and extraction yield. The thermo stability of hydrogen bond in inertinite was stronger than that of vitrinite, especially the thermo stability of hydrogen bond in Pingshuo inertinite.

01 COAL, LIGNITE, AND PEAT↗

The Development of Methanol Industry and Methanol Fuel in China

In 2007, China firmly established itself as the driver of the global methanol industry. The country became the world's largest methanol producer and consumer. The development of the methanol industry and methanol fuel in China is reviewed in this article. China is rich in coal but is short on oil and natural gas; unfortunately, transportation development will need more and more oil to provide the fuel. Methanol is becoming a dominant alternative fuel. China is showing the rest of the world how cleaner transportation fuels can be made from coal.

01 COAL, LIGNITE, AND PEAT↗

Numerical study on convection diffusion for gasification agent in underground coal gasification. Part I: establishment of mathematical models and solving method

The aim of this article is to discuss the distribution law of the gasification agent concentration in a deep-going way during underground coal gasification and the new method of solving the problem for the convection diffusion of the gas. In this paper, the basic features of convection diffusion for the gas produced in underground coal gasification are studied. On the basis of the model experiment, through the analysis of the distribution and patterns of variation for the fluid concentration field in the process of the combustion and gasification of the coal seams within the gasifier, the 3-D non-linear unstable mathematical models on the convection diffusion for oxygen are established. In order to curb such pseudo-physical effects as numerical oscillation and surfeit which frequently occurred in the solution of the complex mathematical models, the novel finite unit algorithm, the upstream weighted multi-cell balance method is advanced in this article, and its main derivation process is introduced.

01 COAL, LIGNITE, AND PEAT↗

Coal production and energy fact in Turkey

Energy is an important input for manufacturing plants and serves human beings to improve their level of development. However, as a person living in this society, each of us is getting anxious since the external dependence on the side of energy increases. In order to handle the deficiencies, which may occur in the near future, it is necessary to look into today's energy policies. In doing so, coal should be kept in mind as a respectful actor.

01 COAL, LIGNITE, AND PEAT↗

For sustainable development: some aspects on energy and environment in Turkey

The high energy demand in Turkey is closely linked to economic growth, industrialization, and population increase. Turkish general energy policies are designed to support economic and social development. Natural conditions of Turkey are favorable for utilization of new and renewable energies, such as hydraulic energy, geothermal energy, wind energy, biomass energy, solar energy, and, probably, nuclear energy. As the use of hydraulic and coal in Turkey will reach its full capacity by 2020, imported natural gas, coal, and other resources will be used to meet the energy demand. By 2020, approximately 75% of final energy demand and 67% of electricity supply will be met by coal, oil, and natural gas. Energy investments, which are closely related with the environmental protection, require massive financial resources. It is also important to use standardized equipment and materials in all areas of energy generation, transmission, distribution, and trade. For a sustainable development, the next investments on industry should be made for the clean technologies in regard with being environment-friendly.

01 COAL, LIGNITE, AND PEAT↗

Exploratory investigation on the use of low-cost alternative media for ultrafine grinding of coal

In this study, the energy efficiency of three alternative grinding media including, coarse silica beads, fine silica beads, and granular sand, were evaluated and compared against standard stainless steel. Stirred mill test results show that both silica beads and granular sand were more efficient than stainless steel in producing ultrafine particles following the order of coarse silica beads>granular sand>fine silica beads>stainless steel. The finest product size corresponding to a P 80 value of 2.33 μm was generated by coarse silica beads with a nominal size of 420×1190 μm, which also consumed the least amount of grinding energy. The specific energy input was reduced by almost 50% as opposed to that of stainless steel, while the operating work index was reduced by 87%. Overall, the test data indicate that grinding media density, media particle size and shape all play a role in determining the optimized grinding behavior of the coal material.

01 COAL, LIGNITE, AND PEAT↗

Parametric study of an acid baking process for rare earth element recovery from a bituminous-coal source

Acid baking treatment is widely used to extract rare earth elements (REEs) from refractory rare earth bearing minerals such as monazite and xenotime. Since these REE minerals have been identified in coal-based sources, a parametric study was conducted to evaluate the impact and optimize the parametric values associated with the acid-baking process when treating a bituminous coal source. The parameters studied using a three-level statistical experimental program were acid baking time, acid solution concentration, baking temperature, and acid solution-to-solids ratio and each were found to significantly impact REE and contaminant element recovery. An increase in baking temperature up to around 250°C improved the light and heavy REE recovery values by more than 50 absolute percentage points relative to performances achieved when direct leaching. Acid baking was needed to dehydroxylate the clays and liberate the REE minerals, which allowed access for the acid to solubilize the REEs. Acid concentration of the solution used for acid baking was studied as a means of minimizing the amount of acid needed to achieve a target REE recovery. However, thermo-gravimetric and differential scanning calorimetry analysis (TGA-DSC) of sulfuric acid under oxidizing atmosphere revealed that the addition of water decreased the evaporation temperature, which explains the lower REE recovery values obtained when using lower acid concentrations. Using pure sulfuric acid at an acid-to-solid ratio of 0.8:1 resulted in recovery values of around 70% for both LREEs and HREEs. The decomposition reaction time was relatively quick with 65% of the TREEs recovered within the first 10 minutes. Water leaching experiments performed on the acid-baked products under a temperature of 25°C instead of 75°C revealed an increase in REE recovery by 10 absolute percentage points, which was likely due to the high solubility of REE-sulfates at room temperatures.

01 COAL, LIGNITE, AND PEAT↗

Dualities in Persistent (Co)Homology

We consider sequences of absolute and relative homology and cohomology groups that arise naturally for a filtered cell complex. We establishalgebraic relationships between their persistence modules, and show that they contain equivalent information. We explain how one can use the existingalgorithm for persistent homology to process any of the four modules, and relate it to a recently introduced persistent cohomology algorithm. Wepresent experimental evidence for the practical efficiency of the latter algorithm.

01 COAL, LIGNITE, AND PEAT↗

A study on the effect of tantalum-impurity content on the superconducting properties of niobium materials used for making superconducting radio frequency cavities

Niobium materials in highly pure form are used in the fabrication of superconducting radio frequency cavities. We present here a study of the superconducting properties of such niobium materials that have been used in the fabrication of high accelerating gradient superconducting radio frequency cavities after determining their tantalum-impurity contents using a synchrotron-based x-ray fluorescence spectroscopy technique. Our results show that there is a small change in superconducting parameters such as T{sub C},H{sub C1} and H{sub C2} when the tantalum-impurity content varies from ≈150 to ≈1300 ppm. In contrast, a buffered chemical polishing of the same niobium samples changes all these superconducting parameters more significantly. The implications of these results on the performance of niobium superconducting radio frequency cavities are discussed.

01 COAL, LIGNITE, AND PEAT↗

Microstrip patch antenna for simultaneous strain and temperature sensing

A patch antenna, consisting of a radiation patch, a dielectric substrate, and a ground plane, resonates at distinct fundamental frequencies that depend on the substrate dielectric constant and the dimensions of the radiation patch. Since these parameters change with the applied strain and temperature, this study investigates simultaneous strain and temperature sensing using a single antenna that has two fundamental resonant frequencies. The theoretical relationship between the antenna resonant frequency shifts, the temperature, and the applied strain was first established to guide the selection of the dielectric substrate, based on which an antenna sensor with a rectangular radiation patch was designed and fabricated. A tensile test specimen instrumented with the antenna sensor was subjected to thermo-mechanical tests. Experiment results validated the theoretical predictions that the normalized antenna resonant frequency shifts are linearly proportional to the applied strain and temperature changes. As a result, an inverse method was developed to determine the strain and temperature changes from the normalized antenna resonant frequency shifts, yielding measurement uncertainty of 0.4 °C and 17.22 μϵ for temperature and strain measurement, respectively.

01 COAL, LIGNITE, AND PEAT↗

Advanced coal gasifier designs using large-scale simulations

Porting of the legacy code MFIX to a high performance computer (HPC) and the useof high resolution simulations for the design of a coal gasifier are described here. MFIX isbased on a continuum multiphase flow model that considers gas and solids to forminterpenetrating continua. Low resolution simulations of a commercial scale gasifier with avalidated MFIX model revealed interesting physical phenomena with implications on thegasifier design, which prompted the study reported here. To be predictive, the simulations needto model the spatiotemporal variations in gas and solids volume fractions, velocities,temperatures with any associated phase change and chemical reactions. These processes occurat various time- and length-scales requiring very high spatial resolution and large number ofiterations with small time-steps. We were able to perform perhaps the largest knownsimulations of gas-solids reacting flows, providing detailed information about the gas-solidsflow structure and the pressure, temperature and species distribution in the gasifier. One keyfinding is the new features of the coal jet trajectory revealed with the high spatial resolution,which provides information on the accuracy of the lower resolution simulations.Methodologies for effectively combining high and low resolution simulations for designstudies must be developed. From a computational science perspective, we found that globalcommunication has to be reduced to achieve scalability to 1000s of cores, hybridparallelization is required to effectively utilize the multicore chips, and the wait time in thebatch queue significantly increases the actual time-to-solution. From our experience,development is required in the following areas: efficient solvers for heterogeneous, massivelyparallel systems; data analysis tools to extract information from large data sets; andprogramming environments for easily porting legacy codes to HPC.

01 COAL, LIGNITE, AND PEAT↗

Influence of process changes on PCDD/Fs produced in an iron ore sintering plant

This study investigated the influence of different charge typologies and additives on the PCDD/Fs amount produced and on the congener profiles in an iron ore sintering plant. Many tests were carried out combining different typologies of charge (iron materials) and solid fuel ('coke breeze' or 'anthracite') with or without the use of urea. The PCDD/Fs produced ranged from 1.2 to 22.7 {mu} g I-TEQ/ton of agglomerate, whereas the PCDD/Fs released to the ambient air ranged from 0.10 to 1.92 ng I-TEQ/Nm{sup 3} because of cleaning in an electrostatic precipitator (ESP) and a Wetfine scrubber (WS). A more homogeneous charge with a higher amount of fine particles charge appeared to produce a lower PCDD/Fs concentration due to a better combustion but this hypothesis needs further investigations on charges having different dimension particles. Only a synergitic action of urea and anthracite was able to reduce the high PCDD/Fs content due to the bad combustion of the more inhomogeneous charge with a lower amount of fine particles. The congener profile was a typical combustion process fingerprint because the PCDFs predominated, the highly chlorinated congeners (HeptaCDD and OctaCDD) prevailed in PCDDs, whereas in PCDFs the profile was more varied; 1,2,3,4,6,7,8-HeptaCDF was the main contributor to the total concentration while 2,3,4,7,8-PentaCDF was the main contributor to the I-TEQ concentration. Whereas all the parameters under scrutiny influenced strongly the amount of PCDD/Fs produced, they affected only slightly the fingerprint of PCDD/Fs. In all cases studied, the reduction obtained using urea, anthracite, or the more homogeneous charge with a higher amount of fine particles was slightly greater on the higher chlorinated congeners in respect to the lower ones.

01 COAL, LIGNITE, AND PEAT↗

Desulphurization and simultaneous treatment of wastewater from blast furnace by pulsed corona discharge

Laboratory tests were conducted for removal of SO{sub 2} from simulated flue gas and simultaneous treatment of wastewater from blast furnace by pulsed corona discharge. Tests were conducted for the flue gas flow from 12 to 18 Nm{sup 3}/h, the simulated gas temperature from 80 to 120 {sup o}C, the inlet flux of wastewater from 33 to 57 L/h, applied voltage from 0 to 27 kV, and SO{sub 2} initial concentration was about 1,430 mg/m{sup 3}. Results showed that wastewater from blast furnace has an excellent ability of desulphurization (about 90%) and pulsed corona discharge can enhance the desulphurization efficiency. Meanwhile, it was observed that the SO{sub 2} removal ratio decreased along with increased cycle index, while it increased as the flux of flue gas was reduced, and increased when the flux of wastewater from blast furnace was increased. In addition, results demonstrated that the content of sulfate radical produced in wastewater increase with an increment of applied pulsed voltage, cycle index, or the flux of flue gas. Furthermore, the results indicated that the higher the inlet content of cyanide the better removal effect of it, and the removal rate can reach 99.9% with a residence time of 2.1 s in the pulsed corona zone during the desulphurization process when the inlet content was higher, whereas there was almost no removal effect when the inlet content was lower. This research may attain the objective of waste control, and can provide a new way to remove SO{sub 2} from flue gas and simultaneously degrade wastewater from blast furnace for integrated steel plants.

01 COAL, LIGNITE, AND PEAT↗

Emission control system for nitrogen oxides using enhanced oxidation, scrubbing, and biofiltration

Nitric oxide (NO) constitutes about 90% of the nitrogen oxide (NOx) species in the flue gases emitted from combustion processes, but NO is difficult to remove in existing scrubbers due to its low solubility. NO may be oxidized with hydrogen peroxide (H{sub 2}O{sub 2}) into soluble species that can be partially removed in wet scrubbers simultaneously with sulfur dioxide (SO{sub 2}) and biofilters located downstream of the scrubber can increase the removal efficiency. This article presents the results of a bench-scale evaluation of such an integrated system combining enhanced oxidation, scrubbing, and biofiltration. Main components of the bench-scale system consisted of a quartz tube in a furnace to simulate the NO oxidation stage and two vertical packed bed cylinders constituting the scrubber and the biofilter. Inlet synthetic gas had a concentration of 50 mu L/L of NO. Overall removal efficiency by the integrated system was in the range of 53% to 93% with an average of 79%, absorption accounted for 43% and biofiltration for 36% of the total removal. Key parameters in the operation of the system are the H{sub 2}O{sub 2}:NO mole ratio, the reaction temperature, the liquid to gas flow ratio, and the biofilter residence time. Experimental results suggest a path for optimization of the technology focusing simultaneously in minimizing H{sub 2}O{sub 2} use in the enhanced oxidation stage, reducing water consumption in the scrubber stage and balancing the residence times in the three stages of the integrated system.

01 COAL, LIGNITE, AND PEAT↗

Determination of heavy metal pollution in Zonguldak (Turkey) by moss analysis (hypnum cupressiforme)

This paper explores the first attempt at determining the levels of atmospheric heavy metal contamination in the Zonguldak province through the analysis of moss (Hypnum cupressiforme Hedw.). Sampling was performed at 24 sites after a wet period to avoid contamination from soil compounds in the province. Dried samples, which were unwashed but cleaned of soil particles and other extraneous material, were digested with HNO{sub 3}/HClO{sub 4}. Concentrations of heavy metals (Fe, Cu, Pb, Cr, Co, Ni, and As) were analyzed by ICP-OES to estimate the geographic distribution of the atmospheric heavy metal depositions. The general order of the concentrations of the heavy metal content in Hypnum cupressiforme Hedw. was observed to be Fe > Pb > Cu > Ni > Cr > As > Co. Mean levels of the measured elements were higher when compared to European levels. Arsenic, iron, and chromium were the most elevated elements when compared with European data. The mean concentrations of these elements in the studied area were 8.3 (Co), 6.7 (Fe), 5.2 (Cr), 4.6 (As), and 2.7 (Ni) times the background levels of the reference site (C3). Among the studied heavy metals, only lead showed little variation in measured values due to traffic in the area. Main sources of increased heavy metal content of the moss samples were found to be: I) the Catalagzi Power Plant (CATES); ii) the Eregli Iron-Steel Plant (ERDEMIR); iii) space heating; and iv) traffic-related emissions. Results are presented in the form of color-scaled contour maps using a Geographic Information System (GIS)-based mapping technique.

01 COAL, LIGNITE, AND PEAT↗