Search NASA⌕ Search

SEARCH · Search NASA

Results for “Layered Structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Synergistically optimized electrical and thermal transport properties of SnTe via alloying high-solubility MnTe

Lead chalcogenides are the most efficient thermoelectric materials. In comparison, SnTe, a lead-free analogue of PbTe, exhibits inferior thermoelectric performance due to low Seebeck coefficient and high thermal conductivity. In this report, we show that we can synergistically optimize the electrical and thermal transport properties of SnTe via alloying Mn. Further, we report that the introduction of Mn (0–50%) induces multiple effects on the band structure and microstructure of SnTe: for the former, it can tune the Fermi level and promote the convergence of the two valence bands, concurrently enhancing the Seebeck coefficient; for the latter, it can profoundly modify the microstructure into an all-scale hierarchical architecture (including nanoscale precipitates/MnTe laminates, stacking faults, layered structure, atomic-scale point defects, etc.) to scatter phonons with a broad range of mean free paths, strongly reducing the lattice thermal conductivity. Meanwhile, most significantly, the Mn alloying enlarges the energy gap of the conduction band (C band) and the light valence band (L band), thereby suppressing the bipolar thermal conductivity by increasing the band gap. The integration of these effects yields a high ZT of 1.3 at 900 K for 17% Mn alloyed SnTe.

36 MATERIALS SCIENCE↗

Evaluation of thermal gradients in longitudinal spin Seebeck effect measurements

In the framework of the longitudinal spin Seebeck effect (LSSE), we developed an experimental setup for the characterization of LSSE devices. This class of device consists in a layered structure formed by a substrate, a ferrimagnetic insulator (YIG) where the spin current is thermally generated, and a paramagnetic metal (Pt) for the detection of the spin current via the inverse spin-Hall effect. In this kind of experiments, the evaluation of a thermal gradient through the thin YIG layer is a crucial point. In this work, we perform an indirect determination of the thermal gradient through the measurement of the heat flux. We developed an experimental setup using Peltier cells that allow us to measure the heat flux through a given sample. In order to test the technique, a standard LSSE device produced at Tohoku University was measured. We find a spin Seebeck S{sub SSE} coefficient of 2.8×10{sup −7} V K{sup −1}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Z-Pinning approach for 3D printing mechanically isotropic materials

Conventional 3D printing approaches are restricted to building up material in a layer-by-layer format, which is more appropriately considered “2.5-D” printing. The layered structure inherently results in significant mechanical anisotropy in printed parts, causing the tensile strength in the build direction (z-axis) to be only a fraction of the in-plane strength – a decrease of 50–75% is common. In this study, a novel “z-pinning” approach is described that allows continuous material to be deposited across multiple layers within the volume of the part. Here, the z-pinning process is demonstrated using a Fused Filament Fabrication (FFF) printer for polylactic acid (PLA) and carbon fiber reinforced PLA. For both materials, z-pinning increased the tensile strength and toughness in the z-direction by more than a factor of 3.5. Direct comparisons to tensile strength in the x-axis showed a significant decrease in mechanical anisotropy as the volume of the pin was increased relative to the void in the rectilinear grid structure. In fact, the PLA sample with the largest pin volume demonstrated mechanically isotropic properties within the statistical uncertainty of the tests. Tensile test results were also analyzed relative to the functional area resisting deformation for each sample.

36 MATERIALS SCIENCE↗

In situ oligomerization of 2-(thiophen-3-yl)acetate intercalated into Zn{sub 2}Al layered double hydroxide

A layered double hydroxide (LDH) with cation composition Zn{sub 2}Al was intercalated with 2-(thiophen-3-yl)acetate (3-TA) monomers. To achieve in situ polymerization and/or oligomerization of the intercalated monomers, soft thermal treatments were carried out, and subsequent hybrid LDH materials were analyzed by means of several characterization techniques using powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), {sup 13}C CP–MAS nuclear magnetic resonance (NMR), electron spin resonance (EPR), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), inductively coupled plasma optical emission spectroscopy (ICP–OES), and elemental analysis. PXRD analysis suggested that the intercalated monomers formed a bilayer. Thermal treatment of the hybrid LDH assembly above 120 °C provokes partially the breakdown of the layered structure, generating the phase zincite. EPR results indicated that vicinal monomers (oligomerization) were bound to each other after hydrothermal or thermal treatment, leading to a polaron response characteristic of electron conductivity localized on a restricted number of thiophene-based monomer segments. Localized unpaired electrons exist in the material and interact with the {sup 27}Al nuclei of the LDH layers by superhyperfine coupling. These unpaired electrons also interact with the surface of ZnO (O{sup 2−} vacancies), formed during the thermal treatments. - Graphical abstract: We synthesized a layered double hydroxide (LDH) with cation composition Zn{sub 2}Al, intercalated with 2-(thiophen-3-yl)acetate (3-TA) monomers, by coprecipitation at constant pH. We thermally treated the material, to achieve in situ polymerization and/or oligomerization of the intercalated monomers. - Highlights: • A Zn{sub 2}Al–LDH was intercalated with 2-(thiophen-3-yl)acetate monomers. • To achieve in situ oligomerization of the monomers, thermal treatments were made. • Thermal treatment above 120 °C causes partially breakdown of the LDH structure. • ESR results indicated a polaron response characteristic of electron conductivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evaluation of the feasibility for detecting hidden corrosion damage in multi-layer gusset plates using multiple inspection techniques

Gusset plates are used to connect the members in truss bridges and they are usually inspected using calipers or conventional thickness measurement ultrasonic testing (UT) devices. The damage mechanism of particular concern in gusset plates is corrosion and the regions most susceptible to corrosion damage are on the gusset interior surface where it intersects the chord, diagonal, and vertical members from water collecting at the interfaces. For heavily loaded gusset plates, one or more shingle plates are used to reinforce the gusset plate, creating a multi-layer structure. While the areas with corrosion damage remain near the members on the gusset plate, the shingle plates cover the gusset plate and greatly limit the surface access to the gusset plate, making UT thickness measurement impractical. Because of the critical nature of the gussets, a viable inspection strategy for multi-layer gusset assemblies must be developed. The premise of this research and development effort was to develop viable, field-deployable inspection approaches for this problem area. This paper presents three separate inspection approaches: two ultrasonic-based techniques and one radiographic approach. Each of these techniques was evaluated on a mock-up specimen provided by the Federal Highway Administration (FHWA) that is representative of gusseted connection from a truss bridge.

42 ENGINEERING↗

Skin explosion of double-layer conductors in fast-rising high magnetic fields

An experiment has been performed to study the electrical explosion of thick cylindrical conductors using the MIG pulsed power generator capable of producing a peak current of 2.5 MA within 100 ns rise time. The experimental goal was to compare the skin explosion of a solid conductor with that of a double-layer conductor whose outer layer had a lower conductivity than the inner one. It has been shown that in magnetic fields of peak induction up to 300 T and average induction rise rate 3 × 10{sup 9} T/s, the double-layer structure of a conductor makes it possible to achieve higher magnetic induction at the conductor surface before it explodes. This can be accounted for, in particular, by the reduction of the ratio of the Joule heat density to the energy density of the magnetic field at the surface of a double-layer conductor due to redistribution of the current density over the conductor cross section.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Synthesis and anisotropic magnetism in quantum spin liquid candidates A YbSe 2 ( A = K and Rb)

The quantum spin liquid (QSL) state in rare-earth triangular lattices has attracted much attention recently due to its potential application in quantum computing and communication. Here, we report the single-crystal growth synthesis, crystal structure characterizations, and magnetic properties of AYbSe 2 (A = K and Rb) compounds. The x-ray diffraction analysis shows that AYbSe 2 (A = K and Rb) crystallizes in a trigonal space group, R-3m (No. 166) with Z = 3. AYbSe 2 possesses a two-dimensional (2D) Yb–Se–Yb layered structure formed by edged-shared YbSe 6 octahedra. The magnetic properties are highly anisotropic for both title compounds, and no long-range order is found down to 0.4 K, revealing the possible QSL ground state in these compounds. The isothermal magnetization exhibits a one-third magnetization plateau when the magnetic fields are applied in the ab-plane. Heat capacity is performed along both ab-plane and c axis and features the characteristic dome for triangular magnetic lattice compounds as a function of magnetic fields. Due to the change in the interlayer and intralayer distance of Yb 3+ , the dome shifts to low fields from KYbSe 2 to RbYbSe 2 . All these results indicate that the AYbSe 2 family presents unique frustrated magnetism close to the possible QSL and noncollinear spin states.

36 MATERIALS SCIENCE↗

Structure and optical properties of [In{sub 1−2x}Sn{sub x}Zn{sub x}]GaO{sub 3}(ZnO){sub m}

Compounds of [In{sub 1−2x}Sn{sub x}Zn{sub x}]GaO{sub 3}(ZnO){sub 1} (x≤0.22) and [In{sub 1−2x}Sn{sub x}Zn{sub x}]GaO{sub 3}(ZnO){sub 2} (x≤0.42) were prepared by solid state processing proving a substantial solid solution of Sn in the layered compounds InGaO{sub 3}(ZnO){sub m} (m=1, 2). Single crystal X-ray diffraction of the compounds reveals two In{sup 3+} ions to be substituted by one Sn{sup 4+} and one Zn{sup 2+} at the octahedral layer preserving the average charge of +3 at these sites. The substitution does not lead to an ordering of the ions but proves for the first time that the octahedral site can be occupied by different ions while all characteristics of the layered structures remain unchanged. Consequences of indium substitution are (i) decrease of the a axis compared to InGaO{sub 3}(ZnO){sub m} according to smaller ionic radii of Sn{sup 4+} and Zn{sup 2+} compared to In{sup 3+} and (ii) shift of the optical band gap to higher energies shown by UV–vis measurements. - Graphical abstract: Substitution limits of indium in InGaO{sub 3}(ZnO){sub m} (IGZO) by Sn and Zn are studied for m=1, 2 by single crystal X-ray diffraction and micro-chemical analysis. - Highlights: • New Oxides [In{sub 1−2x}Sn{sub x}Zn{sub x}]GaO{sub 3}(ZnO){sub m} (m=1, 2) with IGZO type structure. • Sn and Zn substitute for In at octahedral sites. • Crystal structures were characterized by single crystal X-ray diffraction. • Optical band gap energies were determined by UV–vis spectroscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Temperature dependence of the energy bandgap of two-dimensional hexagonal boron nitride probed by excitonic photoluminescence

Hexagonal boron nitride (hBN) is an emerging material for the exploration of new physics in two-dimensional (2D) systems that are complementary to graphene. Nanotubes with a diameter (∼60 nm) that is much larger than the exciton binding energy in hBN have been synthesized and utilized to probe the fundamental optical transitions and the temperature dependence of the energy bandgap of the corresponding 2D hBN sheets. An excitonic transition at 5.901 eV and its longitudinal optical phonon replica at 5.735 eV were observed. The excitonic emission line is blue shifted by about 130 meV with respect to that in hBN bulk crystals due to the effects of reduced dimensionality. The temperature evolution of the excitonic emission line measured from 300 to 800 K revealed that the temperature coefficient of the energy bandgap of hBN nanotubes with large diameters (or equivalently hBN sheets) is about 0.43 meV/{sup 0}K, which is a factor of about 5 times smaller than the theoretically predicted value for the transitions between the π and π* bands in hBN bulk crystals and 6 times smaller than the measured value in AlN epilayers with a comparable energy bandgap. The observed weaker temperature dependence of the bandgap than those in 3D hBN and AlN is a consequence of the effects of reduced dimensionality in layer-structured hBN.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of conductive TiN buffer layer on the growth of stoichiometric VO{sub 2} films and the out-of-plane insulator–metal transition properties

A TiN buffer film is used with a conductive interfacial layer for stoichiometric vanadium dioxide (VO{sub 2}) film growth, creating a layered device with a VO{sub 2} insulator–metal transition. Low-temperature growth (<250 °C) of the VO{sub 2} film on a Ti layer on a Si substrate is achieved using inductively coupled plasma-assisted sputtering. It is found that Ti diffusion and oxidation degrades the VO{sub 2} film quality at higher temperatures, but the introduction of a TiN buffer layer suppresses the degradation and enables growth of a stoichiometric VO{sub 2} film even at 400 °C. The high resistance of the VO{sub 2} film grown on the TiN layer suggests the benefit of using the intrinsic insulator–metal transition of VO{sub 2}. The voltage-triggered switching properties of the layered devices are examined, and the cause of the high out-of-plane resistance in this layered structure is discussed based upon the dependence of the initial resistance as a function the electrode area.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Unique optical excitations in topological insulators (Final Technical Report)

The overall objective of this research is to understand how light interacts with topological insulator (TI) films and layered structures. Unlike normal materials, the electrons in TI films are trapped at the top and bottom surfaces of the film. These electrons have unusual properties, including low mass and high velocity. Light shining on these trapped electrons will excite electron density waves, called plasmons, which inherit the unusual properties of the electrons. This project aims to understand how these plasmons interact with each other and how the plasmon properties change as the film dimensions change. By controlling the physical properties of the films, the optical response of the film can also be controlled. In addition to single TI films, the project will also investigate the properties of stacks of TI films layered with normal insulating films. Stacking these materials results in multiple layers of trapped electrons whose plasmons can interact in ever more complex ways. After these interactions are understood, we can begin to engineer complex TI structures to obtain designer optical phenomena in the far-infrared and THz, wavelength ranges of interest for environmental monitoring and chemical sensing. This research directly addresses DOE Grand Challenges, including understanding how properties of matter emerge from complex electronic correlations and learning how to control these properties as well as the mission of the Basic Energy Sciences program to understand and control matter at the electronic/atomic level.

36 MATERIALS SCIENCE↗

Magnetic resonance in bilayers of ferrite and functionally graded piezoelectric

Highlights: • Ferromagnetic resonance in a ferrite-piezoelectric laminate is studied. • An electric field induced FMR line broadening results from bending the sample. • Ferrite layer between the two piezoelectric layers shows a large line broadening. - Abstract: The particular purpose of this paper is theoretical modeling of magnetoelectric interactions at the ferromagnetic resonance in a layered structure of a ferrite and a piezoelectric with through-thickness graded polarization. We show that using the functionally graded piezoelectric with through-thickness variation of polarization can lead to an electric field induced broadening of ferromagnetic resonance line. As an example, we consider the laminate based on the yttrium iron garnet layer which is placed between two lead zirconate titanate layers with different poling direction. The maximal ferromagnetic resonance line broadening of 9.3 Oe is obtained for the yttrium iron garnet to lead zirconate titanate layer thickness ratio of 1.7 at 9.3 GHz for E equal to 10 kV/cm.

36 MATERIALS SCIENCE↗

Shear Band Formation in Thin-Film Multilayer Columns Under Compressive Loading: A Mechanistic Study

Micro-pillar compression is a popular experimental technique used for characterizing the mechanical behavior of nano- and micro-laminates. The compressive stress–strain response of the column-shaped thin-film composite can be measured, and the deformation and damage features can be revealed by post-test cross-section microscopy. The development of plastic instability in the form of localized strain concentration (shear bands), leading to eventual failure, is frequently observed. In the present study, a computational approach is used to illustrate the commonality of shear band formation from a continuum standpoint. Systematic finite element analyses are conducted, showing that the strain field tends to become localized once plastic yielding commences. Distinct shear offsets of the layered structure can be revealed from the numerical model, which is similar to those observed in experiments. The actual appearance of shear bands depends on the materials’ constitutive behavior and precise geometries. Post-yield strain hardening reduces the propensity of shear band formation, while strain softening enhances it. Imperfections such as the undulated layer geometry, as well as the frictional characteristics between the specimen and test apparatus, can also influence the shear band morphology and overall stress–strain response.

finite element modeling↗

Synthesis and characterization of novel barium iron phosphates: Insight into new structure types tailored by hydrogen atoms

A significant gap in our knowledge of phosphate crystal chemistry is the lack of understanding of what controls the depolymerization of [PO{sub 4}] tetrahedra. A new route using phosphoric acid without any added water at 240 °C has been developed to synthesize two new compounds Ba{sub 2}Fe{sub 2}[H(PO{sub 3}OH){sub 2}][H(P{sub 2}O{sub 7}){sub 2}] and Ba{sub 2}Fe[H(P{sub 2}O{sub 7}){sub 2}], as well as a new polymorph β-BaFe{sub 2}(P{sub 2}O{sub 7}){sub 2} from annealing the former at ≥500 °C. Structural characterizations show that Ba{sub 2}Fe{sub 2}[H(PO{sub 3}OH){sub 2}][H(P{sub 2}O{sub 7}){sub 2}] features a novel 2D {sup 2}{sub ∞}([Fe{sub 2}[H(PO{sub 3}OH){sub 2}][H(P{sub 2}O{sub 7}){sub 2}]]{sup 4−}) layer structure containing both hydrogen-diphosphate [H(P{sub 2}O{sub 7}){sub 2}] and hydrogen-monophosphate [H(PO{sub 3}OH){sub 2}] groups, whereas Ba{sub 2}Fe[H(P{sub 2}O{sub 7}){sub 2}] and β-BaFe{sub 2}(P{sub 2}O{sub 7}){sub 2} possess an 1D chain structure and a 3D framework structure, respectively. These structures support a control of hydrogen on the depolymerization of [PO{sub 4}] groups and our work opens a new way for the synthesis of other novel phosphates using controlled water activities. - Graphical abstract: A new route of controlled water activities led to syntheses of three new compounds, indicating water plays a crucial role in the formation of novel phosphates. - Highlights: • A new mild thermal route for the synthesis of novel phosphates. • Water activities controlling the reaction: 2H{sub 3}PO{sub 4}↔H{sub 4}P{sub 2}O{sub 7}+H{sub 2}O. • Phosphate with mixed hydrogen-monophosphate and diphosphate groups. • H atoms in the structural backbone affect the depolymerization of PO{sub 4} groups.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Hydrothermal synthesis, crystal structure and properties of a novel chain coordination polymer constructed by tetrafunctional phosphonate anions and cobalt ions

A novel cobalt phosphonate, [Co(HL)(H{sub 2}O){sub 3}]{sub n} (1) (L=N(CH{sub 2}PO{sub 3}H){sub 3}{sup 3−}) has been synthesized by hydrothermal reaction at 150 °C and structurally characterized by X-ray diffraction, infrared spectroscopy, elemental and thermogravimetric analysis. Complex 1 features a 1D chain structure with double-channel built from CoO{sub 6} octahedra bridged together by the phosphonate groups. Each cobalt ion is octahedrally coordinated by three phosphonate oxygen atoms and three water molecules. The coordinated water molecules can form the hydrogen bonds with the phosphonate oxygen atoms to link the 1D chains, building a 2D layered structure, further resulting in a 3D network. The luminescence spectrum indicates an emission maximum at 435 nm. The magnetic susceptibility curve exhibits a dominant antiferromagnetic behavior with a weakly ferromagnetic component at low temperatures. - Graphical abstract: The connectivity between cobalt ions and the ligands results in a chain structure with a 1D double-channel structure, which is constructed by A-type subrings and B-type subrings. - Highlights: • The tetrafunctional phosphonate ligand was used as the ligand. • A novel chain structure can be formed by A-type rings and B-type rings. • Two types of rings can form a 1D double-channel structure, along the c-axis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reducing extrinsic damping of surface acoustic waves at gigahertz frequencies

High-frequency surface acoustic waves (SAWs) in the gigahertz range can be generated using absorption from an ultrafast laser in a patterned metallic grating on a substrate. Reducing the attenuation at these frequencies can yield better sensors as well as enable them to better probe phonon and electron-phonon interactions near surfaces. It is not clear from existing experiments which mechanisms dominate damping at high frequencies. We calculate damping times of SAWs due to various mechanisms in the 1–100 GHz range to find that mechanical loading of the grating on the substrate dominates dissipation by radiating energy from the surface into the bulk. To overcome this and enable future measurements to probe intrinsic damping, we propose incorporating distributed acoustic Bragg reflectors in the experimental structure. Layers of alternating materials with contrasting acoustic impedances embedded a wavelength away from the surface serve to reflect energy back to the surface. Using numerical simulations, we show that a single Bragg reflector is sufficient to increase the energy density at the surface by more than five times. We quantify the resulting damping time to find that it is longer than the intrinsic damping time. The proposed structure can enable future measurements of intrinsic damping in SAWs at ∼100 GHz.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Modelling of Blast Furnace with Respective Chemical Reactions in Coke and Ore Burden Layers

The ironmaking blast furnace (BF) is an efficient chemical reactor for producing liquid iron from solid iron ore, where the solids of coke and iron ore are charged in alternative layers and different chemical reactions occur in the two solid layers as they descend. Such respective reacting burden layers have not been considered explicitly in the previous BF models. In this article, a mathematical model based on multi-fluid theory is developed for describing the multiphase reacting flows considering the respective reacting burden layers. Then, this model is applied to a BF, covering the area from the burden surface at the furnace top to the liquid surface above the hearth, to describe the inner states of a BF in terms of the multiphase flows, temperature distribution and reduction process. The results show that some key important features in the layered burden with respective chemical reactions are captured, including fluctuating iso-lines in terms of gas flow and thermochemical behaviours; particularly the latter cannot be well captured in the previous BF models. The temperature difference between gas–solid phases is found to be larger near the raceway, at the cohesive zone and at the furnace top, and the thermal reserved zone can be identified near the shaft. Three chemical reserve zones of hematite, magnetite and wustite can also be observed near the stockline, in the shaft near the wall and near centre, respectively. Inside each reserve zone, the corresponding ferrous oxides stay constantly high in alternative layers; the overall performance indicators including gas utilization efficiency and reduction degree also stay stable in an alternative-layered structure. This model provides a cost-effective tool to investigate the BF in-furnace process and optimize BF operation.

36 MATERIALS SCIENCE↗

Structure of Diamond-Like Silicon–Carbon Films Alloyed by Vanadium

The structure of diamond-like silicon–carbon films formed on silicon substrates by magnetron and plasmatron codeposition using a closed-field magnetron and a plasmatron activated by tungsten cathode has been studied by transmission electron microscopy. The main feature of the films alloyed by vanadium to concentrations of 12–31 at % was found to be a layered structure of the film cross section. It was established that vanadium alloying leads to the formation of vanadium carbide (VC) nanocrystals; the nanocrystal size increases from 1–2 to 10 nm. At the maximum vanadium content, VC nanocrystals have an anisotropic shape: they are extended in the direction perpendicular to the film–substrate interface.

36 MATERIALS SCIENCE↗