Search NASA⌕ Search

SEARCH · Search NASA

Results for “Manufacturing processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Cold-Sprayed NMC622 Composite as a Cathode for Lithium-Ion Batteries

The growing demand for high-energy, low-cost lithium-ion batteries (LIBs) to power electric vehicles (EVs) necessitates advances in both materials and manufacturing processes. Conventional cathode fabrication methods, such as slurry casting and drying, are energy-intensive and pose challenges for scalability and environmental compliance. In this study, we propose cold-spray (CS) deposition as a solvent-free approach for fabricating LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) composite cathodes. Powder blends of NMC622, poly(vinylidene fluoride) (PVDF), and carbon black (CB) are directly deposited onto stainless steel and Inconel substrates under varied gas temperatures, pressures (and thus velocities), and standoff distances. The effects of temperature on the deposit morphology, coating density, and volume are systematically investigated. Computational fluid dynamics simulations reveal that increasing the gas temperature enhances the particle velocity, narrows the spray angle, and reduces the mass concentration radially at the nozzle outlet. CS deposition results in a dense cathode microstructure, accompanied by fracture in polycrystalline NMC622 particles. X-ray diffraction analysis further verifies that there are no phase changes during the deposition process. The electrochemical performance of the cold-sprayed cathodes reveals an initial capacity of approximately 96 mAh g –1 for single-crystal NMC622 and 167 mAh g –1 for polycrystalline NMC622. While these values are modest compared to state-of-the-art slurry-cast cathodes, which typically exhibit 180–200 mAh g –1 under optimized conditions. The results demonstrate a competitive performance given the solvent-free nature of the CS process and compare favorably with tape-cast samples made from identical feedstock. In conclusion, he CS process enables the formation of dense, binder-integrated cathode coatings without the need for solvent processing, offering a promising pathway for scalable, energy-efficient dry electrode manufacturing of next-generation LIBs.

Batteries↗

Survey of PFAS Treatment Technologies

Per- and polyfluoroalkyl substances (PFAS) are a group of manufactured chemicals that have caught the attention of many governmental agencies and researchers. These chemicals are highly stable and possess hydrophobic properties that lead to the widespread use of PFAS in aqueous film forming foams, and household products such as carpets, paper and non-stick cookware (Prevedouros et al., 2006). Regulatory and health advisories have focused determining a lifetime drinking water health advisory of 70 ng/L for PFOA and PFOS (USEPA, 2016). Other PFASs may be present in the environment, along with PFOA and PFOS, due to product manufacturing processes (Prevedouros et al., 2006). A variety of proprietary AFFF formulations were manufactured and sold during different timeframes, thereby complicating the signature and distribution of PFASs in groundwater beneath former firefighting training areas (McGuire et al., 2014). PFOA and PFOS are stable chemicals that persistent in the environment and are difficult to remediate. The understanding of the physicochemical properties and fate and transport of PFASs in groundwater is growing but is still limited (USEPA, 2012). Many traditional approaches such as coagulation and conventional water treatment are ineffective in treating PFOA and PFOS. Selecting the most appropriate remedial strategy for PFOA and PFOS is therefore challenging. In this survey findings from the literature on PFASs removal using various technologies were compiled.

54 ENVIRONMENTAL SCIENCES↗

Materials Dynamics: Area of Leadership [Slides]

Materials Dynamics focuses on deterministic linkages between microstructure-properties-performance of materials at high strain rates and pressures. Understanding process-structure-propertiesperformance (PSPP) is increasingly important for new material qualification, accepting manufacturing process changes, and new materials development.

36 MATERIALS SCIENCE↗

Fuzzy sets predict flexural strength and density of silicon nitride ceramics

In this work, we utilize fuzzy sets theory to evaluate and make predictions of flexural strength and density of NASA 6Y silicon nitride ceramic. Processing variables of milling time, sintering time, and sintering nitrogen pressure are used as an input to the fuzzy system. Flexural strength and density are the output parameters of the system. Data from 273 Si3N4 modulus of rupture bars tested at room temperature and 135 bars tested at 1370 C are used in this study. Generalized mean operator and Hamming distance are utilized to build the fuzzy predictive model. The maximum test error for density does not exceed 3.3 percent, and for flexural strength 7.1 percent, as compared with the errors of 1.72 percent and 11.34 percent obtained by using neural networks, respectively. These results demonstrate that fuzzy sets theory can be incorporated into the process of designing materials, such as ceramics, especially for assessing more complex relationships between the processing variables and parameters, like strength, which are governed by randomness of manufacturing processes.

Cios, Krzysztof J.↗

Evaluation of the Effect of Surface Finish on High-Cycle Fatigue of SLM-IN718

The surface finish of parts produced by additive manufacturing processes is much rougher than the surface finish generated by machining processes, and a rougher surface can reduce the fatigue strength of a part. This paper discusses an effort to quantify that reduction of strength in high-cycle fatigue for selective laser melt (SLM) coupons. A high-cycle fatigue (HCF) knockdown factor was estimated for Inconel 718, manufactured with the SLM process. This factor is the percentage reduction from the maximum stress in fatigue for low-stress ground (LSG) specimens to the maximum stress of those left with the original surface condition at the same fatigue life. Specimens were provided by a number of vendors, free to use their "best practice"; only one heat treat condition was considered; and several test temperatures were characterized, including room temperature, 800F, 1000F, and 1200F. The 1000F data had a large variance, and was omitted from consideration in this document. A first method used linear approximations extracted from the graphs, and only where data was available for both. A recommended knockdown factor of the as-built surface condition (average roughness of approximately 245 micro-inches/inch) versus low-stress ground condition (roughness no more than 4 micro-inches/inch) was established at approximately 1/3 or 33%. This is to say that for the as-built surface condition, a maximum stress of 2/3 of the stress for LSG can be expected to produce a similar life in the as-built surface condition. In this first evaluation, the knockdown factor did not appear to be a function of temperature. A second approach, the "KP method", incorporated the surface finish measure into a new parameter termed the pseudo-stress intensity factor, Kp, which was formulated to be similar to the fracture mechanics stress intensity factor. Using Kp, the variance seemed to be reduced across all sources, and knockdown factors were estimated using Kp over the range where data occurred. A plot of the results suggests that the knockdown factor is a function of temperature, and that for low lives the knockdown might be lower than the knockdown observed above about one million cycles, where it tended to stabilize. This was not universal for all temperatures tested. The higher temperature tests are thought to be influenced by the test temperature, which perhaps continued the aging process. Further evaluation of the method is suggested.

Lambert, D. M.↗

Renewable Energy for Industrial Environmental Management

Costs for renewable energy technologies have declined rapidly in the past decade and their use for residential, commercial, and utility scale electricity has grown exponentially as they become cost competitive. Simultaneously, industrial and manufacturing processes have been increasingly seeking ways to reduce emissions and operational costs in highly competitive sectors. With these combined drivers of lower cost and reduced environmental impact, renewable energy may become a viable energy provider for industrial processes such as oil and gas, mining, chemical refining, food production, and manufacturing. Renewable energy technologies may also partner with other reduced emission energy sources, such as small modular nuclear reactors and carbon capture and utilization, to create cleaner and circular industrial systems for reduced resource use. The Joint Institute for Strategic Energy Analysis (JISEA), which is a partnership of the National Renewable Energy Laboratory (NREL) and five universities and others, has been studying to potential for application of clean energy technologies to the heterogenous energy demands in industry. Dr. Jill Engel-Cox will present an overview of NREL and JISEA, the status and potential future of renewable energy technologies, and collaborations with the oil and gas industry and other industrial sectors to improve their environmental performance and reduce operational costs.

ENERGY PLANNING, POLICY, AND ECONOMY↗

Additive Manufacturing of Advanced High Temperature Masking Fixtures for EBPVD TBC Coating

The purpose of this Manufacturing Demonstration Facility (MDF) technical collaboration project between Praxair Surface Technologies, Inc. (PST) and Oak Ridge National Laboratory (ORNL) was to develop an additive manufacturing process to fabricate next generation high temperature masking fixtures for coating of turbine airfoils with ceramic Thermal Barrier Coatings (TBC) by the Electron Beam Physical Vapor Deposition (EBPVD) process. Typical masking fixtures are sophisticated designs and require complex part manipulation in order to achieve the desired coating distribution. Fixtures are typically fabricated from high temperature nickel (Ni) based superalloys. The fixtures are fabricated from conventional processes by welding of thin sheet material into a complex geometry, to decrease the weight load for the manipulator and to reduce the thermal mass of the fixture. Recent attempts have been made in order to fabricate the fixtures through casting, but thin walled sections are difficult to cast and have high scrap rates. This project focused on understanding the potential for fabricating high temperature Ni based superalloy fixtures through additive manufacturing. Two different deposition processes; electron beam melting (EBM) and laser powder bed fusion were evaluated to determine the ideal processing route of these materials. Two different high temperature materials were evaluated. The high temperature materials evaluated were Inconel 718 and another Ni base alloy, designated throughout the remainder of this document as Alloy X, as the alloy composition is sensitive. Inconel 718 is a more widely utilized material for additive manufacturing although it is not currently the material utilized for current fixtures. Alloy X is the alloy currently used for the fixtures, but is not a commercially available alloy for additive manufacturing. Praxair determined it was possible to build the fixture using laser powder bed technology from Inconel 718. ORNL fabricated the fixture geometry using the EBM technology in order to compare deposition features such as surface roughness, geometric accuracy, deposition rate, surface and subsurface porosity, and material quality. It was determined that the laser powder bed technology was ideal for the geometry and requirements of the fixture set by Praxair, and Praxair moved forward with the purchase of a laser powder bed system. The subsequent portion of the project focused on determining the ideal processing parameters for alloy X for the laser powder bed system using ORNL’s Renishaw laser powder bed system. Praxair supplied gas atomized powders of alloy X material with properties specified by ORNL. ORNL printed text cube arrays in order to determine the ideal combination of laser powder and laser travel speed in order to maximize material density, improve surface quality, and maintain geometric accuracy. Additional powder supplied by Praxair was used to fabricate a full-scale fixture component.

42 ENGINEERING↗

Recycling Irradiated Nuclear Graphite - A Greener Path Forward

Here we report the successful recycle of irradiated graphite to fabricate new nuclear graphite using conventional manufacturing processes (albeit on a on a bench scale). Radiological concerns such as the containment of contamination in industrial scale manufacturing plants, or the release of 14C, were not considered. Moreover, a study of the annealing kinetics was conducted to elucidate the extent of property recovery over a representative temperature range. The goal of the preliminary work reported here was to determine if nuclear graphite, produced through the normal graphite fabrication process, but using crushed, previously irradiated nuclear graphite, could be manufactured with sufficient mechanical integrity to warrant further investigation

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Clean Energy Manufacturing: Renewable Energy Technology Benchmarks

The manufacturing of clean energy technologies has become a global enterprise. An analysis of four clean energy technology manufacturing processes—wind turbine components, crystalline silicon solar photovoltaic modules, light-duty vehicle lithium-ion battery cells, and light-emitting diodes—was conducted to provide a reference point for comparison over time as this sector evolves. The manufacturing supply chain analysis included processing of raw materials, making required subcomponents, and assembling final products, using benchmarks that crossed 12 economies: Brazil, Canada, China, Germany, India, Japan, Malaysia, Mexico, South Korea, Republic of China (Taiwan), the United Kingdom, and the United States. Larger economies, with extensive manufacturing supply chains and high prevailing wages, tend to retain more value added from clean energy manufacturing than small economies. Manufacturing of clean energy technologies drives extensive trade among economies to support the widely distributed supply chain links. Production of wind turbine components and photovoltaic modules is more centralized than production of light-emitting diodes and lithium-ion battery cells. Across the four clean energy technologies evaluated, there was generally an excess of manufacturing capacity relative to global supply.

benchmarks↗

Metrology for Fuel Cell Manufacturing

The project was divided into three subprojects. The first subproject is Fuel Cell Manufacturing Variability and Its Impact on Performance. The objective was to determine if flow field channel dimensional variability has an impact on fuel cell performance. The second subproject is Non-contact Sensor Evaluation for Bipolar Plate Manufacturing Process Control and Smart Assembly of Fuel Cell Stacks. The objective was to enable cost reduction in the manufacture of fuel cell plates by providing a rapid non-contact measurement system for in-line process control. The third subproject is Optical Scatterfield Metrology for Online Catalyst Coating Inspection of PEM Soft Goods. The objective was to evaluate the suitability of Optical Scatterfield Microscopy as a viable measurement tool for in situ process control of catalyst coatings.

08 HYDROGEN↗

Design optimization of lightweight automotive seatback through additive manufacturing compression overmolding of metal polymer composites

With the growing demand for enhanced automotive fuel efficiency and environmental sustainability, there is a need for lightweighting automotive components through innovative design and manufacturing processes. Here, this study leverages a combination of numerical iterative design optimization and hybrid additive manufacturing–compression molding (AM-CM) technique for metal polymer composites to lightweight an automotive seatback. The AM-CM process enables robust mechanical interlocking between metals and composites, boasting high stiffness and strength with low overall density. Replacing metallic components with such metal polymer composites allows for comparable mechanical performance while significantly reducing the overall weight. First, the automotive seatback design space is reduced to critical load carrying regions using topology optimization and high stress concentration areas are identified using finite element analysis. Next, a lightweight metal polymer subcomponent is designed for a high stress concentration region. The full seatback frame with spatially heterogeneous material-specific design is then iteratively optimized to enable enhanced stiffness with minimal weight. Overall, the automotive seatback frame designed with location-specific metal, polymer, and metal polymer composite materials weighs 20% less than the metal-only design while exhibiting similar stiffness.

36 MATERIALS SCIENCE↗

A coupled thermo‐chemo‐mechanical reduced‐order multiscale model for predicting process‐induced distortions, residual stresses, and strength

Summary We study residual stresses and part distortion induced by a manufacturing process of a polymer matrix composite and its effect on the component strength. Unlike most of the thermo‐chemo‐mechanical models in the literature where governing multiphysics equations are directly formulated on the macroscale, we present a multiscale‐multiphysics approach. To address the enormous computational complexity involved, a reduced‐order homogenization was originally developed for a single physics problem is employed. The proposed reduced‐order two‐scale thermo‐chemo‐mechanical model has been validated for predicting part distortion beam strength in three‐point bending test. It is shown that while macroscopic stresses are relatively low, and therefore often ignored in practice, stresses at the scale of microconstituents are significant and may have an effect on the overall composite component strength.

Yuan, Zifeng↗

Optimization of edge bead removal (EBR) process to enhance defect reduction in optical lithography

Defect reduction remains a critical objective in the integrated circuit manufacturing process, particularly within the highly re-entrant lithography modules where minimizing defects is crucial. Defects at the wafer edge can contaminate lithography modules and downstream processing equipment, leading to redistribution onto the wafer surface and adversely affecting overall device yield. A persistent challenge in the resist coating process is the formation of resist edge beads, driven by the strong Van der Waals attraction of excess photoresist (PR) to itself and the underlying substrate. The edge bead removal (EBR) process is a standard cleaning step designed to eliminate these edge beads and prevent potential contamination. Here, in this study, we identify the sources of EBR induced defects and additional EBR process encroachment toward edge patterning during the EBR cleaning process. This study provides a comprehensive study aimed at optimizing the EBR cleaning process to effectively eliminate EBR-induced defects, thereby enhancing overall device yield. Specifically, we identify three primary defects induced by the EBR cleaning process: rainbow-type, finger-shaped, and teardrop-type defects. Our experimental study reveals that in addition to EBR rinse time, PR cast time is crucial parameters contributing to the formation of these defects. By properly optimizing the PR cast time and EBR rinse time, we were able to remove nearly 100 % of dense clusters of defects that were easily visible even at low magnification optical microscopy throughout the wafer edge. We observed that shorter PR casting times shows edge defects caused by inefficient EBR process because of insufficient time for PR to fully settle causing superfluous PR to continue flowing toward wafer edge during EBR clearing step, leading to partial removal of PR at the wafer edge and the formation of rainbow defects. Proper optimization of both PR casting time and EBR chemistries dispense time is essential to resolve these defects, ensuring efficient EBR cleaning process and improved overall device yield.

42 ENGINEERING↗

VARTM Process Modeling of Aerospace Composite Structures

A three-dimensional model was developed to simulate the VARTM composite manufacturing process. The model considers the two important mechanisms that occur during the process: resin flow, and compaction and relaxation of the preform. The model was used to simulate infiltration of a carbon preform with an epoxy resin by the VARTM process. The model predicted flow patterns and preform thickness changes agreed qualitatively with the measured values. However, the predicted total infiltration times were much longer than measured most likely due to the inaccurate preform permeability values used in the simulation.

Song, Xiao-Lan↗

EE&RE; Session: CIGS (Presentation)

This project supports the Solar America Initiative by carrying out work on target topics identified for Photovoltaic Systems: (1) Improving cell and module efficiency of thin film Cu(In,Ga)Se2 materials; (2) Implementing the Science and Technology Facility (S&TF) and the Process Development and Integration Laboratory (PDIL) to facilitate laboratory/industry interaction in developing PV manufacturing technologies; (3) Addressing industrial issues in materials and manufacturing processes with the objective to lower the cost of PV power; (4) Providing technology transfer efforts to accelerate transition of thin film PV technology to market and deployment; (5) Assisting R&D efforts to asses and improve reliability and stability of thin film PV products; and (6) Assist the SAI TPPs in technical matters related to CIGS PV technology.

14 SOLAR ENERGY↗

Statistical analysis of the Nb 3 Sn strand production for the ITER toroidal field coils

The ITER toroidal field (TF) strand procurement initiated the largest Nb 3 Sn superconducting strand production hitherto. The industrial-scale production started in Japan in 2008 and finished in summer 2015. Six ITER partners (so-called Domestic Agencies, or DAs) are in charge of the procurement and involved eight different strand suppliers all over the world, of which four are using the bronze route (BR) process and four the internal-tin (IT) process. In total more than 500 tons have been produced including excess material covering losses during the conductor manufacturing process, in particular the cabling. The procurement is based on a functional specification where the main strand requirements like critical current, hysteresis losses, Cu ratio and residual resistance ratio are specified but not the strand production process or layout. We introduce the analysis on the data acquired during the quality control (QC) process that was carried out to ensure the same conductor performance requirements are met by the different strand suppliers regardless of strand design. The strand QC is based on 100% billet testing and on applying statistical process control (SPC) limits. Throughout the production, samples adjacent to the strand pieces tested by the suppliers are cross-checked ('verified') by their respective DAs reference labs. The level of verification was lowered from 100% at the beginning of the procurement progressively to approximately 25% during the final phase of production. Based on the complete dataset of the TF strand production, an analysis of the SPC limits of the critical strand parameters is made and the related process capability indices are calculated. In view of the large-scale production and costs, key manufacturing parameters such as billet yield, number of breakages and piece-length distribution are also discussed. Furthermore, the results are compared among all the strand suppliers, focusing on the difference between BR and IT processes. Following the completion of the largest Nb 3 Sn strand production, our experience gained from monitoring the execution of the QC activities and from auditing the results from the measurements is summarised for future superconducting strand material procurement activities.

Vostner, A.↗

Efficient screening of rare large pit anomalies on polished surfaces using a minimalist sampling scheme

Lawrence Livermore National Laboratory (LLNL) has made significant strides in generating clean energy through its inertial confinement fusion (ICF) experiments. These experiments rely on high-density carbon (HDC) coated shells to encapsulate the fusion fuel. The success of these experiments is heavily dependent on the surface quality of these shells, as even minor imperfections, such as deep pits, can negatively impact fusion yield. Ensuring the required smoothness involves an extensive surface-finishing process that spans approximately 20 stages, making it both time-intensive and resource-demanding. A critical challenge in this process is the need for high-resolution scans to detect rare deep pits, which can be costly and impractical if performed on every shell. This highlights the necessity of developing more efficient scanning methods to optimize time and cost without compromising accuracy. To address these challenges, we introduce a novel approach that employs the multivariate Dvoretzky–Kiefer–Wolfowitz (DKW) inequality to provide a probabilistic upper bound on the error in estimating pit distribution characteristics via a Kernel Density Estimator (KDE). This error bound enables efficient and reliable estimation of pit distribution characteristics at a specified statistical confidence level using a minimal number of surface scans. The integrated DKW-KDE approach was validated through surface-finishing experiments across two batches of HDC-coated shells, demonstrating consistent and robust performance across multiple stages of the surface-finishing experiments. The validation studies suggest that the integrated DKW-KDE approach achieves comparable accuracy in estimating the risk of deleterious large pits with six scans, thus conserving time and resources. Further evaluations show that performance remains consistent across batches and over multiple polishing stages. In conclusion, based on these findings, one can leverage the minimal-scan insights to strategically improve the bottleneck inspection process, thus enhancing the productivity and quality of shell polishing and similar challenging manufacturing processes.

Inertial confinement fusion↗

Manufacturing scalability implications of materials choice in inorganic solid-state batteries

The pursuit of scalable and manufacturable all-solid-state batteries continues to intensify, motivated by the rapidly increasing demand for safe, dense electrical energy storage. Here, we describe the numerous, often conflicting implications of materials choices that have been made in the search for effective mitigations to the interfacial instabilities plaguing solid-state batteries. Specifically, we show that the manufacturing scalability of solid-state batteries can be governed by at least three principal consequences of materials selection: (1) the availability, scaling capacity, and price volatility of the chosen materials’ constituents, (2) the manufacturing processes needed to integrate the chosen materials into full cells, and (3) the cell performance that may be practically achieved with the chosen materials and processes. While each of these factors is, in isolation, a pivotal determinant of manufacturing scalability, we show that consideration and optimization of their collective effects and trade-offs is necessary to more completely chart a scalable pathway to manufacturing.

25 ENERGY STORAGE↗