Search NASA⌕ Search

SEARCH · Search NASA

Results for “RESISTANCE DEVICE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

Utility of reactively sputtered CuN{sub x} films in spintronics devices

We have studied nitrified copper (CuN{sub x}) thin films grown by reactive sputtering in the context of spintronic devices. The Ar-to-N{sub 2} flow ratio enables tunability of the electrical resistivity and surface roughness of the CuN{sub x} films, with the former increasing to nearly 20 times that of Cu, and the latter reduced to the atomic scale. Incorporating this into a Ta/CuN{sub x}/Ta seed stack for spin valves improves the current-in-plane (CIP) magnetoresistance; maximum magnetoresistance results with CuN{sub x} seed layer and Cu interlayer. Finally, finite element modeling results are presented that suggest the use of CuN{sub x} in nanocontact spin torque oscillators can enhance current densities by limiting the current spread through the device. This may positively impact threshold currents, power requirements, and device reliability.

36 MATERIALS SCIENCE↗

A surface plasmon enabled liquid-junction photovoltaic cell

Plasmonic nanosystems have recently been shown to be capable of functioning as photovoltaics and of carrying out redox photochemistry, purportedly using the energetic electrons and holes created following plasmonic decay as charge carriers. Although such devices currently have low efficiency, they already manifest a number of favorable characteristics, such as their tunability over the entire solar spectrum and a remarkable resistance to photocorrosion. Here, we report a plasmonic photovoltaic using a 25 μm thick electrolytic liquid junction which supports the iodide/triiodide (I - /I 3 - ) redox couple. The device produces photocurrent densities in excess of 40 μA cm -2 , an open circuit voltage ( V oc ) of ~0.24 V and a fill factor of ~0.5 using AM 1.5 G solar radiation at 100 mW cm -2 . The photocurrent and the power conversion efficiency are primarily limited by the low light absorption in the 2-D gold nanoparticle arrays. The use of a liquid junction greatly reduces dielectric breakdown in the oxide layers utilized, which must be very thin for optimal performance, leading to a great improvement in the long-term stability of the cell's performance.

Lee, Woo-ram↗

Purely electronic insulator-metal transition in rutile VO 2

Volatile resistive switching in neuromorphic computing can be tuned by external stimuli such as temperature or electric-field. However, this type of switching is generally coupled to structural changes, resulting in slower reaction speed and higher energy consumption when incorporated into an electronic device. The vanadium dioxide (VO 2 ), which has near room temperature metal-insulator transition (MIT), is an archetypical volatile resistive switching system. Here, we demonstrate an isostructural MIT in an ultrathin VO 2 film capped with a photoconductive cadmium sulfide (CdS) layer. Transmission electron microscopy, resistivity experiments, and first-principles calculations show that the hole carriers induced by CdS photovoltaic effect are driving the MIT in rutile VO 2 . The insulating-rutile VO 2 phase has been proved and can remain stable for hours. Our finding provides a new approach to produce purely electronically driven MIT in VO 2 , and widens its applications in fast-response, low-energy neuromorphic devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Photoinduced Halide Segregation in Ruddlesden–Popper 2D Mixed Halide Perovskite Films

2D lead halide perovskites, which exhibit bandgap tunability and increased chemical stability, have been found to be useful for designing optoelectronic devices. Reducing dimensionality with decreasing number of layers (n = 10–1) also imparts resistance to light-induced ion migration as seen from the halide ion segregation and dark recovery in mixed halide (Br:I = 50:50) perovskite films. The light-induced halide ion segregation efficiency, as determined from difference absorbance spectra, decreases from 20% to <1% as the dimensionality is decreased for 2D perovskite film from n = 10 to 1. The segregation rate constant (ksegregation), which decreases from 5.9 × 10 –3 s –1 (n = 10) to 3.6 × 10 –4 s –1 (n = 1), correlates well with nearly an order of magnitude decrease observed in charge-carrier lifetime (τ average = 233 ps for n = 10 vs τ avg = 27 ps for n = 1). The tightly bound excitons in 2D perovskites make charge separation less probable, which in turn decreases the halide mobility and resulting phase segregation. Furthermore, the importance of controlling the dimensionality of the 2D architecture in suppressing halide ion mobility is discussed.

14 SOLAR ENERGY↗

Supercurrent Flow in Multiterminal Graphene Josephson Junctions

We investigate the electronic properties of ballistic planar Josephson junctions with multiple super- conducting terminals. Our devices consist of monolayer graphene encapsulated in boron nitride with molybdenum- rhenium contacts. Resistance measurements yield multiple resonant features, which are attributed to supercurrent flow among adjacent and nonadjacent Josephson junctions. In particular, we find that superconducting and dissipative currents coexist within the same region of graphene. We show that the presence of dissipative currents primarily results in electron heating and estimate the associated temperature rise. We find that the electrons in encapsulated graphene are efficiently cooled through the electron-phonon coupling.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Origin of Giant Ionic Currents in Carbon Nanotube Channels

Fluid flow inside carbon nanotubes is remarkable: transport of water and gases is nearly frictionless, and the small channel size results in selective transport of ions. Very recently, devices have been fabricated in which one narrow single-walled carbon nanotube spans a barrier separating electrolyte reservoirs. Ion current through these devices is about 2 orders of magnitude larger than predicted from the bulk resistivity of the electrolyte. Electroosmosis can drive these large excess currents if the tube both is charged and transports anions or cations preferentially. By building a nanofluidic field-effect transistor with a gate electrode embedded in the fluid barrier, we show that the tube carries a negative charge and the excess current is carried by cations. The magnitude of the excess current and its control by a gate electrode are correctly predicted by the Poisson-Nernst-Planck-Stokes equations.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Study of graphene p-n junctions formed by the electrostatic modification of the SiO2 substrate

Abstract We study the transport properties of mm-scale CVD graphene p-n junctions, which are formed in a single gated graphene field effect transistor configuration. Here, an electrical-stressing-voltage technique served to modify the electrostatic potential in the SiO 2 /Si substrate and create the p-n junction. We examine the transport characteristics about the Dirac points that are localized in the perturbed and unperturbed regions in the graphene channel and note the quantitative differences in the Hall effect between the perturbed and unperturbed regions. The results also show that the longitudinal resistance is highly sensitive to the external magnetic field when the Hall bar device operates as a p-n junction.

Science & Technology - Other Topics↗

Integration of an Axcelis Optima HD Single Wafer High Current Implanter for p- and n-S/D Implants in an Existing Batch Implanter Production Line

This paper is focused on the integration and qualification of an Axcelis Optima HD single wafer high current spot beam implanter in an existing 200 mm production line with different types of Axcelis batch implanters for high current applications. Both the design of the beamline and the beam shape are comparable between single wafer and batch high current spot beam implanters. In contrast to the single wafer high current ribbon beam implanter, energy contamination is not a concern for the considered spot beam tool because the drift mode can be used down to energies in the 2 keV region. The most important difference between single wafer and batch high current implanters is the significantly higher dose rate and, therefore, the higher damage rate for the single wafer tool due to the different scanning architecture. The results of the integration of high dose implantations, mainly for p- and n-S/D formation, for DRAM 110 nm without pre-amorphization implantation (PAI), CMOS Logic from around 250 nm down to 90 nm without and with PAI, are presented and discussed. Dopant concentration profile analysis using SIMS was performed for different technologies and implantation conditions. The impurity activation was measured using sheet resistance and in some cases spreading resistance technique was applied. The amorphous layer thickness was measured using TEM. Finally, device data are presented in combination with dose, energy and beam current variations. The results have shown that the integration of implantation processes into crystalline structure without PAI is more complex and time consuming than implantations into amorphous layer where the damage difference due to the different dose rates is negligible.

36 MATERIALS SCIENCE↗

Ni doping of semiconducting boron carbide

The wide band gap, temperature stability, high resistivity, and robustness of semiconducting boron carbide make it an attractive material for device applications. Undoped boron carbide is p type; Ni acts as a n-type dopant. Here we present the results of controlled doping of boron carbide with Ni on thin film samples grown using plasma enhanced chemical vapor deposition. The change in the dopant concentration within the thin film as a function of the dopant flow rate in the precursor gas mixture was confirmed by x-ray photoelectron spectroscopy measurements; with increasing dopant concentration, current-voltage (I-V) curves clearly establish the trend from p-type to n-type boron carbide.

36 MATERIALS SCIENCE↗

Evaluation of freestanding boron-doped diamond grown by chemical vapour deposition as substrates for vertical power electronic devices

In this study, 4 x 4 mm{sup 2} freestanding boron-doped diamond single crystals with thickness up to 260 {mu}m have been fabricated by plasma assisted chemical vapour deposition. The boron concentrations measured by secondary ion mass spectroscopy were 10{sup 18} to 10{sup 20} cm{sup -3} which is in a good agreement with the values calculated from Fourier transform infrared spectroscopy analysis, thus indicating that almost all incorporated boron is electrically active. The dependence of lattice parameters and crystal mosaicity on boron concentrations have also been extracted from high resolution x-ray diffraction experiments on (004) planes. The widths of x-ray rocking curves have globally shown the high quality of the material despite a substantial broadening of the peak, indicating a decrease of structural quality with increasing boron doping levels. Finally, the suitability of these crystals for the development of vertical power electronic devices has been confirmed by four-point probe measurements from which electrical resistivities as low as 0.26 {Omega} cm have been obtained.

36 MATERIALS SCIENCE↗

Pulsed laser deposition of high-quality thin films of the insulating ferromagnet EuS

High-quality thin films of the ferromagnetic insulator europium(II) sulfide (EuS) were fabricated by pulsed laser deposition on Al{sub 2}O{sub 3} (0001) and Si (100) substrates. A single orientation was obtained with the [100] planes parallel to the substrates, with atomic-scale smoothness indicates a near-ideal surface topography. The films exhibit uniform ferromagnetism below 15.9 K, with a substantial component of the magnetization perpendicular to the plane of the films. Optimization of the growth condition also yielded truly insulating films with immeasurably large resistance. This combination of magnetic and electric properties opens the gate for future devices that require a true ferromagnetic insulator.

36 MATERIALS SCIENCE↗

Large surface conductance and superconductivity in topological insulator microstructures

Controllable geometric manipulation via micromachining techniques provides a promising tool for enhancing useful topological electrical responses relevant to future applications such as quantum information science [P. J. W. Moll, “Focused ion beam microstructuring of quantum matter,” Annu. Rev. Condens. Matter Phys. 9, 147 (2018); Jang et al., “Observation of half-height magnetization steps in Sr 2 RuO 4 ,” Science 331, 186 (2011); Moll et al., “Transport evidence for Fermi-arc-mediated chirality transfer in the Dirac semimetal Cd 3 As 2 ,” Nature 535, 266 (2016); Moll et al., “Evidence for hydrodynamic electron flow in PdCoO 2 ,” Science 351, 1061 (2016)]. Here, we present microdevices fabricated with a focused ion beam from an indium-doped topological insulator Pb 1–x Sn x Te. Furthermore, with the device thickness on the order of 1 μm and an extremely large bulk resistivity, we achieve an unprecedented enhancement of the surface contribution to about 30% of the total conductance near room temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low-cost sensor-based damage localization for large-area monitoring of FRP composites

Abstract In recent years, there has been growing interest in self-sensing structural materials across research and industry sectors. Detecting and locating structural damage typically requires numerous sensors wired to a data acquisition (DAQ) circuit, rendering implementation impractical in real structures. This paper proposes an innovative, cost-effective sensor network for damage detection and localization in fiber-reinforced polymer composites. The innovation encompasses three key elements: (1) utilizing carbon fiber tows within the composite as piezoresistive sensors, eliminating the need for additional foreign sensor devices; (2) introducing a novel sensor layout wherein sensor tow branches with varied resistance values are connected in parallel, reducing the number of connections to the DAQ circuit and cutting manufacturing costs significantly; (3) developing a practical sensor terminal fabrication technique to minimize manufacturing expenses. The proposed design methodology for the branch resistance values is first validated using a demonstration panel. Subsequently, the overall strategy is assessed by conducting impact tests on carbon and glass fiber-reinforced composite specimens. Results validate the sensor’s ability to accurately detect and locate structural damage.

Demo, Luke B. (ORCID:0000000208806522)↗

Design and Analysis of an Integral MPPT Control Law for Wave Energy Conversion Systems

In this paper, we propose an integral-based maximum power point tracking (MPPT) algorithm for point absorber wave energy conversion (WEC) systems. A permanent magnet synchronous generator (PMSG) is coupled to the point absorber and its drive implements the proposed MPPT control. While the rotating frame of reference of the PMSG implements power control, the slower mechanical frequency of the incident waves are processed with an additional transformation that yields another set of dc dynamics. The computed dc power in the new reference frame, which is focused on slow wave dynamics, is input to the MPPT control law that tunes the emulated resistance of the machine drive to extract peak power from the wave absorber device. We derive a stability condition for the proposed controller and validate our control design on a simulated 10kW system.

wave energy, maximum power point tracking (MPPT), ↗

Microcantilever heater-thermometer with integrated temperature-compensated strain sensor

The present invention provides microcantilever hotplate devices which incorporate temperature compensating strain sensors. The microcantilever hotplate devices of the present invention comprise microcantilevers having temperature compensating strain sensors and resistive heaters. The present invention also provides methods for using a microcantilever hotplate for temperature compensated surface stress measurements, chemical/biochemical sensing, measuring various properties of compounds adhered to the microcantilever hotplate surface, or for temperature compensated deflection measurements.

47 OTHER INSTRUMENTATION↗

Flow control valve

Disclosed is a flow device including an inlet, an outlet, and a plurality of fluid flow paths hydraulically connected in parallel to the inlet and the outlet, wherein the plurality of fluid flow paths forms a first ring of fluid flow paths circumferentially arranged at a first radial distance from a centerline of the fluid flow device a second ring of fluid flow patch circumferentially arranged at a second radial distance from the centerline of the fluid flow device, each of the plurality of fluid flow paths has a first hydraulic resistance in a forward flow direction and a second hydraulic resistance in a reverse flow direction, and the second hydraulic resistance is greater than the first hydraulic resistance.

Siebert, Brett W.↗

Methods and systems for rapid prototyping of high density circuits

A preferred embodiment provides, for example, a system and method of integrating fluid media dispensing technology such as direct-write (DW) technologies with rapid prototyping (RP) technologies such as stereolithography (SL) to provide increased micro-fabrication and micro-stereolithography. A preferred embodiment of the present invention also provides, for example, a system and method for Rapid Prototyping High Density Circuit (RPHDC) manufacturing of solderless connectors and pilot devices with terminal geometries that are compatible with DW mechanisms and reduce contact resistance where the electrical system is encapsulated within structural members and manual electrical connections are eliminated in favor of automated DW traces. A preferred embodiment further provides, for example, a method of rapid prototyping comprising: fabricating a part layer using stereolithography and depositing thermally curable media onto the part layer using a fluid dispensing apparatus.

42 ENGINEERING↗

Directional ballistic transport in the two-dimensional metal PdCoO2

Abstract In an idealized infinite crystal, the material properties are constrained by the symmetries of the unit cell. The point-group symmetry is broken by the sample shape of any finite crystal, but this is commonly unobservable in macroscopic metals. To sense the shape-induced symmetry lowering in such metals, long-lived bulk states originating from an anisotropic Fermi surface are needed. Here we show how a strongly facetted Fermi surface and the long quasiparticle mean free path present in microstructures of PdCoO 2 yield an in-plane resistivity anisotropy that is forbidden by symmetry on an infinite hexagonal lattice. We fabricate bar-shaped transport devices narrower than the mean free path from single crystals using focused ion beam milling, such that the ballistic charge carriers at low temperatures frequently collide with both of the side walls that define the channel. Two symmetry-forbidden transport signatures appear: the in-plane resistivity anisotropy exceeds a factor of 2, and a transverse voltage appears in zero magnetic field. Using ballistic Monte Carlo simulations and a numerical solution of the Boltzmann equation, we identify the orientation of the narrow channel as the source of symmetry breaking.

36 MATERIALS SCIENCE↗