Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tracking error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Level B/C software ground navigation program. Delta-T processor

The Delta-T Processor (DTP) computes the instantaneous downtrack error in a specified orbiter onboard navigation state vector recovered via downlink telemetry. The downtrack error, expressed in units of time, is computed based on current incoming Earth based range and Doppler navigation tracking data and the ground selected onboard navigation state vector. The computed time difference when used to modify the timetag of the vector used for onboard navigation reduces the instantaneous downtrack error in this vector to within the threshold of the DTP, the input data, and the onboard software. This threshold is currently estimated to be approximately 2 to 4 nautical miles. The DTP is not restricted to using only onboard vectors. Any vector, either input via the manual entry device or accessible via the vector administration table, may be used. The DTP does not require that both data types be available.

Source record↗
NASA NTRS2002

CATS-based Agents That Err

This report describes preliminary research on intelligent agents that make errors. Such agents are crucial to the development of novel agent-based techniques for assessing system safety. The agents extend an agent architecture derived from the Crew Activity Tracking System that has been used as the basis for air traffic controller agents. The report first reviews several error taxonomies. Next, it presents an overview of the air traffic controller agents, then details several mechanisms for causing the agents to err in realistic ways. The report presents a performance assessment of the error-generating agents, and identifies directions for further research. The research was supported by the System-Wide Accident Prevention element of the FAA/NASA Aviation Safety Program.

Callantine, Todd J.↗
NASA NTRS2012

Quaternion-Based Control Architecture for Determining Controllability/Maneuverability Limits

Dynamic inversion has often been used in the simulation environment to rapidly prototype controls for the full flight envelope, because of its capacity for assessing a vehicle s maneuver performance and proper sizing of control surfaces. Generally, the architectures involve either a direct inversion of the entire set of equations of motion or a sequential set of inversions exploiting time scale separation in the vehicle dynamics where faster parameters are considered as controls for slower varying parameters. The proposed architecture builds on the latter using a quaternion formulation that provides singularity free tracking. Of interest, the proposed architecture simplifies the sequential approach by exploiting a simpler kinematic inversion in place of a more difficult inversion typically used. This kinematic relationship accurately describes the angular rate required to drive some reference frame of interest to a desired attitude at some desired quaternion error rate. A simple PID control is used to define the desired quaternion error rate. The paper develops the theoretical framework for the approach, and shows results in tracking a desired trajectory.

Bacon, Barton J↗
NASA NTRS1982

An advanced tracker design for pointing and control of space vehicles using the charge injection device

The use of charge transfer devices (CTD) in pointing and control of space vehicles is examined, with emphasis on the use of charge injection devices (CID). The selection of CTD type and CID operation, including CID signal and noise analysis and signal improvement, are discussed. Star tracking operational advantages of the CTD are pointed out, and the tracking optical concept is discussed and graphically depicted. The position interpolation procedure and the effects of rate of stellar motion on position interpolation are considered, and error analysis is examined. Finally, the breadboard and test program are discussed in detail, coarse and fine acquisition, test for star, track pattern, test procedure and results. An overall accuracy performance of approximately 0.02 pixels or approximately 0.8 arcsec for the test equipment and tracker was obtained.

Jones, C.↗
NASA NTRS1994

Gravity model improvement using the DORIS tracking system on the SPOT 2 satellite

A high-precision radiometric satellite tracking system, Doppler Orbitography and Radio-positioning Integrated by Satellite system (DORIS), has recently been developed by the French space agency, Centre National d'Etudes Spatiales (CNES). DORIS was designed to provide tracking support for missions such as the joint United States/French TOPEX/Poseidon. As part of the flight testing process, a DORIS package was flown on the French SPOT 2 satellite. A substantial quantity of geodetic quality tracking data was obtained on SPOT 2 from an extensive international DORIS tracking network. These data were analyzed to assess their accuracy and to evaluate the gravitational modeling enhancements provided by these data in combination with the Goddard Earth Model-T3 (GEM-T3) gravitational model. These observations have noise levels of 0.4 to 0.5 mm/s, with few residual systematic effects. Although the SPOT 2 satellite experiences high atmospheric drag forces, the precision and global coverage of the DORIS tracking data have enabled more extensive orbit parameterization to mitigate these effects. As a result, the SPOT 2 orbital errors have been reduced to an estimated radial accuracy in the 10-20 cm RMS range. The addition of these data, which encompass many regions heretofore lacking in precision satellite tracking, has significantly improved GEM-T3 and allowed greatly improved orbit accuracies for Sun-synchronous satellites like SPOT 2 (such as ERS 1 and EOS). Comparison of the ensuing gravity model with other contemporary fields (GRIM-4C2, TEG2B, and OSU91A) provides a means to assess the current state of knowledge of the Earth's gravity field. Thus, the DORIS experiment on SPOT 2 has provided a strong basis for evaluating this new orbit tracking technology and has demonstrated the important contribution of the DORIS network to the success of the TOPEX/Poseidon mission.

Nerem, R. S.↗
NASA NTRS1989

Impact of device level faults in a digital avionic processor

This study describes an experimental analysis of the impact of gate and device-level faults in the processor of a Bendix BDX-930 flight control system. Via mixed mode simulation, faults were injected at the gate (stuck-at) and at the transistor levels and, their propagation through the chip to the output pins was measured. The results show that there is little correspondence between a stuck-at and a device-level fault model, as far as error activity or detection within a functional unit is concerned. In so far as error activity outside the injected unit and at the output pins are concerned, the stuck-at and device models track each other. The stuck-at model, however, overestimates, by over 100 percent, the probability of fault propagation to the output pins. An evaluation of the Mean Error Durations and the Mean Time Between Errors at the output pins shows that the stuck-at model significantly underestimates (by 62 percent) the impact of an internal chip fault on the output pins. Finally, the study also quantifies the impact of device fault by location, both internally and at the output pins.

Suk, Ho Kim↗
NASA NTRS1994

Global and regional kinematics with GPS

The inherent precision of the doubly differenced phase measurement and the low cost of instrumentation made GPS the space geodetic technique of choice for regional surveys as soon as the constellation reached acceptable geometry in the area of interest: 1985 in western North America, the early 1990's in most of the world. Instrument and site-related errors for horizontal positioning are usually less than 3 mm, so that the dominant source of error is uncertainty in the reference frame defined by the satellites orbits and the tracking stations used to determine them. Prior to about 1992, when the tracking network for most experiments was globally sparse, the number of fiducial sites or the level at which they could be tied to an SLR or VLBI reference frame usually, set the accuracy limit. Recently, with a global network of over 30 stations, the limit is set more often by deficiencies in models for non-gravitational forces acting on the satellites. For regional networks in the northern hemisphere, reference frame errors are currently about 3 parts per billion (ppb) in horizontal position, allowing centimeter-level accuracies over intercontinental distances and less than 1 mm for a 100 km baseline. The accuracy of GPS measurements for monitoring height variations is generally 2-3 times worse than for horizontal motions. As for VLBI, the primary source of error is unmodeled fluctuations in atmospheric water vapor, but both reference frame uncertainties and some instrument errors are more serious for vertical than horizontal measurements. Under good conditions, daily repeatabilities at the level of 10 mm rms were achieved. This paper will summarize the current accuracy of GPS measurements and their implication for the use of SLR to study regional kinematics.

King, Robert W.↗
NASA NTRS1990

A noncontacting motion monitoring system for an astronaut translation aid

The development of a noncontacting motion sensing system designed to monitor the movement of a cart along a track in the low earth orbit space environment is described. The system uses Hall effect sensors to detect the position of small permanent magnets located along the track. The measurement criteria are described, the system design is discussed, and estimates of the system error are given. The system will be used on the Crew and Equipment Translation Aid (CETA) experiment scheduled for the STS37 flight in November 1990. It will allow the position, velocity, and acceleration of the cart to be determined as it moves along the track.

Finley, Tom D.↗
NASA NTRS1976

Improvements in navigation resulting from the use of dual spacecraft radiometric data

If two spacecraft lying along similar geocentric lines-of-sight are simultaneously tracked by two nearby ground stations (dual spacecraft two-station tracking), navigational capabilities may be substantially improved. A thorough accuracy analysis study of dual spacecraft tracking using simulated tracking data based on the trajectories of Viking and Mariner Jupiter-Saturn '77(MJS '77) missions has been carried out. Results of the study reveal the following advantages: (1) cancellation of platform parameter and transmission media modelling errors in short arc solutions, (2) accurate encounter guidance for the trailing spacecraft, (3) reduction of total tracking time requirements, and (4) rapid determination of the orbit following a maneuver on either spacecraft. It is shown that dual spacecraft data types can improve navigational capabilities by a factor of 5 to 10, under the conditions of small angular separation (not exceeding 3 degrees) of the two spacecraft and well determined trajectory of the reference spacecraft. The research to carry out and the data to obtain before the new technique can be used in interplanetary navigation are pointed out.

Chao, C. C.↗
NASA NTRS2015

Swarm Flyby Gravimetry

This study describes a new technology for discerning the gravity fields and mass distribution of a solar system small body, without requiring dedicated orbiters or landers. Instead of a lander, a spacecraft releases a collection of small, simple probes during a flyby past an asteroid or comet. By tracking those probes from the host spacecraft, one can estimate the asteroid's gravity field and infer its underlying composition and structure. This approach offers a diverse measurement set,equivalent to planning and executing many independent and unique flyby encounters of a single spacecraft. This report assesses a feasible hardware implementation, derives the underlying models,and analyzes the performance of this concept via simulation.In terms of hardware, a small, low mass, low cost implementation is presented, which consists of a dispenser and probes. The dispenser contains roughly 12 probes in a tube and has a total size commensurate with a 6U P-Pod. The probes are housed in disc shaped sabots. When commanded,the dispenser ejects the top-most probe using a linear motor. The ejected probe separates from its sabots and unfolds using internal springs. There are two types of probes, each designed for a particular tracking modality. The reflective probe type, tracked by a telescope, unfolds to forma diffusely reflective sphere. The retroreflector probe type, tracked by a lidar, unfolds to form a corner-cube retroreflector assembly. Both types are designed to spherical so that their attitude doesn't affect the spacecraft's tracking performance.This analysis indicates that the point-mass term of small bodies larger than roughly 500 m in diameter can be observed from a host spacecraft that tracks locally deployed probes throughout a flyby to an uncertainty of better than 5%. The conditions by which this measurement is possible depends on the characteristics of the asteroid (size, type), the flyby velocity, and the type of tracking available (angles-only or angles+ranging). For most encounters, a few (1-3) well placed probes can be very effective, with marginal improvement for additional probes. Given realistic deployment errors, an encounter may require roughly 10-12 probes to ensure that 1-3 achieve their target. Long duration tracking of probes flying by large asteroids (>5 km diameter) can sometimes provide observability of the gravity field's first spherical harmonic, J( sub 2). In summary, this method offers a feasible, affordable approach to enabling or augmenting flyby science.

Atchison, Justin↗
NASA NTRS1993

A preliminary error analysis of the gravity field recovery from a lunar Satellite-to-Satellite mission

A low cost lunar Satellite-to-Satellite radio tracking mission in a low-low configuration could considerably improve the existing knowledge about the lunar gravity field. The impact of various mission parameters that may contribute to the recovery of the gravity field, such as satellite altitude, satellite separation mission duration, measurement precision and sampling interval were quantified using the Jekeli-Rapp algorithm. Preliminary results indicate that the gravity field resolution up to harmonic degree 40 to 80 is feasible depending on various mission configurations. Radio tracking data from a six-month mission with a precision of 1 mm/s every 10 s and 300 km satellite separation at 150 km altitude will permit the determination of 5 deg x 5 deg mean gravity anomalies with an error of approximately 15 mgals. Consideration of other unaccounted error sources of instrumental, operational, and environmental nature may lower this resolution.

Iz, Huseyin B.↗
NASA NTRS2015

Full-Carpet Design of a Low-Boom Demonstrator Concept

The Cart3D adjoint-based design framework is used to mitigate the undesirable o -track sonic boom properties of a demonstrator concept designed for low-boom directly under the flight path. First, the requirements of a Cart3D design mesh are determined using a high-fidelity mesh adapted to minimize the discretization error of the CFD analysis. Low-boom equivalent area targets are then generated at the under-track and one off-track azimuthal position for the baseline configuration. The under-track target is generated using a trim- feasible low-boom target generation process, ensuring that the final design is not only low-boom, but also trimmed at the specified flight condition. The o -track equivalent area target is generated by minimizing the A-weighted loudness using an efficient adjoint-based approach. The configuration outer mold line is then parameterized and optimized to match the off-body pressure distributions prescribed by the low-boom targets. The numerical optimizer uses design gradients which are calculated using the Cart3D adjoint- based design capability. Optimization constraints are placed on the geometry to satisfy structural feasibility. The low-boom properties of the final design are verified using the adaptive meshing approach. This analysis quantifies the error associated with the CFD mesh that is used for design. Finally, an alternate mesh construction and target positioning approach offering greater computational efficiency is demonstrated and verified.

Ordaz, Irian↗
NASA NTRS1963

The autotrack system

The autotrack system accurately senses the direction of arrival, at the horn-reflector antenna, of the microwave beacon signal from the communications satellite. When this direction does not coincide with the horn-reflector pointing direction, error correcting voltages are automatically generated to enable the antenna direction system to steer the antenna toward the satellite. This paper presents a simple analysis of error voltage generation, a description of the system, and a brief discussion of system performance. Measurements at Andover, Maine, have shown that an angular pointing error of less than 0.005 degree is maintained by the antenna when using the autotrack system to follow the Telstar communications satellite.

SATELLITE COMMUNICATION↗
NASA NTRS1969

Multipath performance of a TDRS system employing wideband FM VHF signals

An approximate theoretical analysis is presented for the effects of specular reflection multipath on the performance of a one-way tracking and data relay satellite-to-user link. The analysis pertains to the wideband FM system employing a sinusoidal subcarrier to achieve spectrum spreading. Bounds on multipath effects are derived for receivers with and without limiters and for data modulated on the carrier or the subcarrier. For data modulation, performance is evaluated in terms of an additive lowpass signal at the data detection filter. Doppler and range tracking performance is evaluated in terms of root-mean-square (RMS) error of carrier frequency in a carrier PLL and rms phase jitter in a subcarrier PLL.

Sohn, S. J.↗
NASA NTRS1972

Hybrid carrier and modulation tracking loops.

The tracking loops presented herein exploit the coherency of the observed data sidebands at the carrier frequency for improvements in phase-coherent tracking, telemetry, and command system performance. The loop is motivated by one aspect of generalized harmonic analysis, viz., the so-called cross spectrum. The basic idea of the loop centers around using the power in the composite received signal (sidebands including cross-modulation components) to enhance the signal-to-noise ratio in the carrier tracking loop, thereby reducing the noisy reference loss and ultimately the subcarrier reference jitter, the symbol sync jitter, and the error probability of the data detector. The modulation from the extracted sidebands is removed in such a way that the coherence power in the data sidebands can be used for tracking at the carrier frequency.

Lindsey, W. C.↗
NASA NTRS1974

Conditioning of MVM '73 radio-tracking data

An extensive effort was undertaken to edit Mariner 10 radiometric tracking data. Interactive computer graphics were used for the first time by an interplanetary mission to detect blunder points and spurious signatures in the data. Interactive graphics improved the former process time by a factor of 10 to 20, while increasing reliability. S/X dual Doppler data was used for the first time to calibrate charged particles in the tracking medium. Application of the charged particle calibrations decreased the orbit determination error for a short data arc following the 16 March 1974 maneuver by about 80%. A new model was developed to calibrate the earth's troposphere with seasonal adjustments. The new model has a 2% accuracy and is 5 times better than the old model.

Koch, R. E.↗
NASA NTRS1976

Tracker implementation for the orbiter Ku-band communications antenna

Possible implementations and recommendations for the Space Shuttle Ku-Band integrated communications/radar antenna tracking system were evaluated. Communication aspects involving the Tracking Data Relay Satellite (TDRS)/Orbiter Ku-Band link are emphasized. Detailed analysis of antenna sizes, gains and signal-to-noise ratios shows the desirability of using maximum size 36-inch diameter dish and a triple channel monopulse. The use of the original baselined 20 inch dish is found to result in excessive acquisition time since the despread signal would be used in the tracking loop. An evaluation of scan procedures which includes vehicle dynamics, designation error, time for acquisition and probability of acquisition shows that the conical scan is preferred since the time for lock-on for relatively slow look angle rates will be significantly shorter than the raster scan. Significant improvement in spherical coverage may be obtained by reorienting the antenna gimbal to obtain maximum blockage overlap.

Rudnicki, J. F.↗