Search NASA⌕ Search

SEARCH · Search NASA

Results for “Two Phase Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
DOE OSTI2015

Effects of gas flow on oxidation reaction in liquid induced by He/O{sub 2} plasma-jet irradiation

We present here analysis of oxidation reaction in liquid by a plasma-jet irradiation under various gas flow patterns such as laminar and turbulence flows. To estimate the total amount of oxidation reaction induced by reactive oxygen species (ROS) in liquid, we employ a KI-starch solution system, where the absorbance of the KI-starch solution near 600 nm behaves linear to the total amount of oxidation reaction in liquid. The laminar flow with higher gas velocity induces an increase in the ROS distribution area on the liquid surface, which results in a large amount of oxidation reaction in liquid. However, a much faster gas flow conversely results in a reduction in the total amount of oxidation reaction in liquid under the following two conditions: first condition is that the turbulence flow is triggered in a gas flow channel at a high Reynolds number of gas flow, which leads to a marked change of the spatial distribution of the ROS concentration in gas phase. Second condition is that the dimpled liquid surface is formed by strong gas flow, which prevents the ROS from being transported in radial direction along the liquid surface.

42 ENGINEERING↗
DOE OSTI2024

Modeling of Sagging for 3D Printed Layers During the Curing Process

Here, a printed layer of silica-enforced poly(dimethylsiloxane)-co-(diphenylsiloxane) is modeled as a two-phase system consisting of air and polymer with an interface set up during the printing process. The structural geometry changes mostly due to the action of surface tension, while all material properties are strongly temperature dependent. Polymer flow is described using equations of the extended Herschel–Bulkley model, with parameters strongly dependent on temperature and degree of curing. Parameters of the model are determined using flow sweep measurements and separate experiments with vertical structure sagging at different temperatures. The curing process is modeled using dependencies between the curing rate, degree of curing, and temperature obtained in studies by differential scanning calorimetry. The developed model is used for simulations of printed structure deformations with different initial and boundary conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Active nematic ratchet in asymmetric obstacle arrays

We numerically investigate the effect of an asymmetric periodic obstacle array in a two-dimensional active nematic. We find that activity in conjunction with the asymmetry leads to a ratchet effect or unidirectional flow of the fluid along the asymmetry direction. The directional flow is still present even in the active turbulent phase when the gap between obstacles is sufficiently small. We demonstrate that the dynamics of the topological defects transition from flow mirroring to smectic-like as the gap between obstacles is made smaller, and explain this transition in terms of the pinning of negative winding number defects between obstacles. This also leads to a nonmonotonic ratchet effect magnitude as a function of obstacle size, so that there is an optimal obstacle size for ratcheting at fixed activity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Presentation of the Dana Medal of the Mineralogical Society of America for 2019 to Matthew J. Kohn

If there’s one word that describes Matt Kohn’s career, it’s eclectic. What is possibly most astounding is that Matt’s contributions have not been in a single, narrow field, but in two distinct fields that, at least at first glance, are not even that closely related. While Matt is a metamorphic petrologist par excellence making significant contributions to the fields of geo-thermobarometry, metamorphic phase equilibria, metamorphic fluid flow, monazite geochronology, argon geochronology, and metamorphic P-T-t studies and their tectonic implications, he has also pioneered the use of stable isotopes to unravel vertebrate paleodietary patterns and paleoclimate.

58 GEOSCIENCES↗
DOE OSTI2021

An Integrated Multiscale Modeling Framework for Unconventional Stimulation and Production (Final Report)

The production of oil and gas from unconventional reservoirs largely depends upon two main features operating at different scales: (1) the establishment of a reservoir scale stimulated fracture network that effectively communicates with the rock volume, enhancing permeability and transport to the wellbore and (2) the coupled multi-phase flow, chemical and mechanical processes affecting the migration of hydrocarbons from the low permeability country rock adjacent to the stimulated fracture network. To date, there has been no simulation framework that allows seamless and integrated prediction of these features across spatial scales extending from the pore structure of the reservoir rock to the volume of the reservoir. In addition, there has been a lack of suitable field measurements to test such models, as stimulation and production data are often proprietary and not freely available to national laboratories and academic institutions. New multi-scale simulation capabilities are needed that are validated against suitable field-based research experiments on hydraulic fracturing and shale production.

02 PETROLEUM↗
DOE OSTI2024

Active Nematic Ratchet in Asymmetric Obstacle Arrays

We numerically investigate the effect of an asymmetric periodic obstacle array in a two-dimensional active nematic. We find that activity in conjunction with the asymmetry leads to a ratchet effect or unidirectional flow of the fluid along the asymmetry direction. The directional flow is still present even in the active turbulent phase when the gap between obstacles is sufficiently small. We demonstrate that the dynamics of the topological defects transition from flow-mirroring to smectic-like as the gap between obstacles is made smaller, and explain this transition in terms of the pinning of negative winding number defects between obstacles. This also leads to a non-monotonic ratchet effect magnitude as a function of obstacle size, so that there is an optimal obstacle size for ratcheting at fixed activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Modeling Dense Particle Flow in Multistage and Obstructed Flow Receivers Using High Fidelity Simulations

Particles are a leading contender for next-generation, concentrating solar power technologies, and the design of the particle receiver is critical to minimize the levelized cost of electricity. Falling particle receivers (FPRs) are a viable receiver concept, but many new designs feature complex particle obstructions that include dense discrete phase flows. This creates additional challenges for modeling as particle-to-particle interactions (i.e., collisions) and particle drag become more complex. To improve upon existing modeling strategies, a CFD-DEM simulation capability was created by coupling two independent codes: Sierra/Fuego and LAMMPS. A suitable receiver model was then defined using a traditional continuum-based model for the air and a granular model for the particle curtain. A sensitivity study was executed using this model to determine the relevance of different granular model inputs on important quantities of interest in obstructed flow FPRs: the particle velocity and curtain opacity. The study showed that the granular model inputs had little effect on the particle velocity magnitude and curtain opacity after an obstruction.

Mills, Brantley↗
DOE OSTI2018

Volume fraction determination of the annular three-phase flow of gas-oil-water using adaptive neuro-fuzzy inference system

The use of adaptive neuro-fuzzy inference system (ANFIS) has been reported for predicting the volume fractions in a gas–oil–water multiphase system. In fact, the volume fractions in the annular three-phase flow are measured based on a dual energy metering system consisting of {sup 152}Eu and {sup 137}Cs and one NaI detector using ANFIS. Since the summation of volume fractions is constant, therefore ANFIS must predict only two volume fractions. In this study, three ANFIS networks are applied. The first is utilized to predict the gas and water volume fractions. The next one is applied to predict the gas and oil, and the last one is used to predict the water and oil volume fractions. In the next step, ANFIS networks must be trained based on numerically obtained data from MCNP-X code. Then, the average testing errors of these three networks are computed and compared. The network with the least error has been selected as the best predictor model.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2022

Room-temperature polariton quantum fluids in halide perovskites

Abstract Quantum fluids exhibit quantum mechanical effects at the macroscopic level, which contrast strongly with classical fluids. Gain-dissipative solid-state exciton-polaritons systems are promising emulation platforms for complex quantum fluid studies at elevated temperatures. Recently, halide perovskite polariton systems have emerged as materials with distinctive advantages over other room-temperature systems for future studies of topological physics, non-Abelian gauge fields, and spin-orbit interactions. However, the demonstration of nonlinear quantum hydrodynamics, such as superfluidity and Čerenkov flow, which is a consequence of the renormalized elementary excitation spectrum, remains elusive in halide perovskites. Here, using homogenous halide perovskites single crystals, we report, in both one- and two-dimensional cases, the complete set of quantum fluid phase transitions from normal classical fluids to scatterless polariton superfluids and supersonic fluids—all at room temperature, clear consequences of the Landau criterion. Specifically, the supersonic Čerenkov wave pattern was observed at room temperature. The experimental results are also in quantitative agreement with theoretical predictions from the dissipative Gross-Pitaevskii equation. Our results set the stage for exploring the rich non-equilibrium quantum fluid many-body physics at room temperature and also pave the way for important polaritonic device applications.

42 ENGINEERING↗
DOE OSTI2024

Electromagnetic Inhomogeneous-Energy-Density-Driven Instability in the UCLA Large Plasma Device (EM-IEDDI in LAPD) (Final Technical Report)

Using the Large Plasma Device (LAPD), the electromagnetic signatures associated with the inhomogeneous-energy-density-driven (IEDD) instability were targeted for documentation in a lab experiment. Exploitable features of LAPD are the extreme-length, high-beta, low-collisionality, and excellent reproducibility. The signatures of interest were mode amplitude, mode structure, frequency spectrum, phase velocity, and excitation threshold. The abrupt inhomogeneity at the interface between two coaxial plasma columns, that have disparate space potential values, were expected to generate a strong, localized, transverse, dc electric field and form a strong ExB-flow inhomogeneity that was expected to trigger broadband, intermediate-frequency waves that propagate many gyroradii beyond the interfacial source region. WVU was unable to destabilize the IEDDI mode in LAPD. Experimental limitation of three different parameters conspire to prevent IEDDI-favorable conditions even though Alfven-favorable conditions are met. Electron-neutral collision frequency is too high, Structuring of the radial profile of the radial electric field is negligible and the control of that structure is minimal, and the Magnetic field is too large for some purposes and too small for other purposes. WVU designed a new antenna and relied on externally-driving the IEDDI (instead of spontaneous destabilization). The antenna operation failed for unforeseen reasons and lack of electrician time and availability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2018

CTF_

CTF is a thermal-hydraulic simulation tool designed for modeling the reactor vessel region of light water reactors. The code is capable of modeling both coolant and solid regions and includes a nuclear fuel rod model. Coolant is represented with a 9-equation (two phases plus droplets and non-condensable gas) model with closure relationships being provided for normal and accident conditions. Meshing is done using the subchannel approach, which models the coolant region as a collection of parallel 1-D flow paths that communicate laterally through "gaps". CTF also includes a collection of supporting software tools that include: Xml2ctf - A utility for creating native CTF input decks from a simplified input file; pyCTF - A collection of Python utilities used for post-processing CTF results, manipulating CTF input models, and testing differences between output files; CTFFuel - A separate front-end to the CTF fuel rod solver package; Multistate - A separate driver for CTF that communicates through the code coupling interface; and veraAPI - A c++ interface to the code.

Salko, Robert K↗
DOE OSTI2023

Experimental Investigation of a Phase Change Material Charged Serpentine Heat Exchanger with Louvered Fins

Phase change material heat exchangers (PCM-HX) can be used as a latent heat thermal energy storage (LHTES) component in heat pump applications to further enhance the efficiency of a heat pump as well as to yield financial savings by peak-load shifting. In this paper, a low-cost commercially available aluminum serpentine heat exchanger with louvered fins was experimentally investigated to check its thermal performance as a PCM-HX. A transparent rectangular box fabricated from acrylic plates served as a PCM container. Two cameras were used to capture the phase change process of the PCM on the front and top sides of the container during the experiment. A total of 88 installed temperature sensors throughout the test setup and a mass flow meter enabled a quantitative analysis of the PCM-HX as well. The energy balance deviation between the estimated theoretical and experimentally calculated PCM storage was ±14% considering the often-neglected heat loss and thermal mass of the PCM-HX. PCM temperature profiles, charge and discharge rates, and energy densities under different test conditions were also investigated.

42 ENGINEERING↗
DOE OSTI2023

Lime slurry treatment of soils developing on abandoned coal mine spoil: Linking contaminant transport from the micrometer to pedon-scale

Historical and abandoned coal mine spoil continues to generate acid- and metal(loid)-rich porewaters and represents a geographically large and diffuse non-point source of contamination to local watersheds. A potentially inexpensive approach to treat these materials and soils developing on them is through the application of lime slurries, to neutralize acidity and encourage the (co)precipitation of metal(loids) with Fe(III)-(oxy)hydroxides, and potentially other metal-oxides and/or Ca-bearing phases. Here, the efficacy of this approach was evaluated through parallel field application and laboratory-based flow-through column experiments. The field site is Huff Run sub-watershed 25 located in Tuscarawas County, Ohio and was chosen in part because it was previously classified as one of the most highly AMD-impacted sub-watersheds in the region. Two locations with historical spoil were chosen and suction lysimeters were installed at 25 and 75 cm depth to monitor porewater composition on two sides at the base of each pile. Half of each slope received seven lime slurry treatments from June through October of 2017. A suite of aqueous (ICP-OES, IC, and TOC-L) and solid phase geochemical and mineralogical approaches (quantitative SEM-EDS and synchrotron μ-XRF) were used to determine how composition, texture, morphology, and spatial distribution of mineral coatings differ in pre- and post-lime treated soils, and how that impacts the distribution and transport of trace metal(loid)s. Mine spoil porewater at site 1 was slightly less alkaline (pH ranging from 7.04 to 7.37) than at site 2 (ranging from 7.55 to 7.71), and average electrical conductivity values at site 1 (316–405 μS cm —1 ) were slightly lower than at site 2 (358–464 μS cm —1 ), although differences between the sites were not significant. Porewater pH and electrical conductivity in all lysimeters decreased over the course of the field season but there was no obvious response to lime treatment at either site or any depth. At site 1, both treatment and depth were significant factors affecting Ca, K, Ni, SO 4 2— , and DOC concentrations while only treatment effects were significant for dissolved Al and Cu (p < 0.05). For all soils, there were no trends in metal concentration observed over time although DOC and SO 4 2— decreased over the field season. Pedon-scale changes in metal porewater concentrations in response to treatment were linked to micrometer-scale changes in mineral surface coatings; specifically, higher concentrations of Ca, Fe, Mn, and Zn were observed in the coatings and no changes were observed in Fe redox speciation, whereas total S decreased likely due to oxidation of S in coal fragments. In contrast to the field experiment, the column experiments exhibited a much greater response in effluent composition with respect to lime treatment. The untreated columns had approximately an order of magnitude more H + leached over the course of the experiment (p < 0.001) and resulted in greater Ca, Al, Cu, and DIC leached and less Mn, Zn, and SO 4 2— . Soils treated with the lime slurry in the column experiments exhibited larger and thicker secondary Fe-coatings, including the addition of Fe-sulfates. Despite clear trends in the laboratory-based column experiment where the lime-to-soil ratio was higher, the effects were either muted or undetected in the field pilot project, suggesting that a higher application rate of lime in the field is needed to achieve a similar effect. This work provides evidence that a less alkaline lime slurry could be a practical and inexpensive method of treating coal mine spoil-impacted soils and represents an important step in linking laboratory-based remediation studies to implemented field-based studies.

58 GEOSCIENCES↗
DOE OSTI2024

Interactions of laser-driven tin ejecta microjets over phase transition boundaries

Ejecta microjets offer an experimental methodology to study high-speed particle laden-flow interactions, as microjets consist of millions of particulates traveling at velocities of several kilometers per second and are easily generated by most common shock drives. Previous experiments on the OMEGA Extended Performance laser found that collisions between two counter-propagating laser-driven tin ejecta microjets varied as a function of drive pressure; jets generated near shock pressures of 10 GPa passed through each other without interacting, whereas jets generated at shock pressures of over 100 GPa interacted strongly, forming a cloud around the center interaction point. In this paper, we present a more systematic scan of tin ejecta microjet collisions over intermediate pressure regimes to identify how and at what shock pressure interaction behavior onsets. Radiographs of interacting microjets at five different laser drive energies qualitatively demonstrate that interaction behavior onsets slowly as a function of laser drive energy. Quantitative mass and density metrics from each radiograph provide trends on jet characteristics and collisional mass dispersion. It is observed that jetting mass, jet densities, and mass dispersion increase with increasing drive pressures and that the increased jet density at the higher drive energies may account for the increased mass dispersion. This work provides an important step in the understanding of tin ejecta microjet collisions and paves the way for future studies on the physics dominating high-speed particle-laden flow interactions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Techno-Economic Wind Blade Manufacturing Model to Identify Opportunities for Cost Improvements Phase II IACMI Project 4.6/4.8

In IACMI Project 4.6 and IACMI Project 4.8, an Excel-based Techno-Economic Model (TEM) of the manufacturing process for composite wind turbine blades and a DELMIA Factory Flow Simulation of a generic wind blade manufacturing facility was developed. Together, these two tools provide a combined economic modeling capability that accounts for the material, labor, overhead and full-lifecycle operating costs associated with wind blade manufacturing as well as the impact of process flow and factory layout on overall manufacturing efficiency. The tools provide a novel means of detailed comparative analysis of the economic feasibility of proposed technologies and process changes for blade manufacturing. The modeling tools were developed with close support from members of industry and visits to multiple blade manufacturing facilities. With industry oversight, a detailed generalized manufacturing process plan and facility layout were developed with manufacturing parameters, material costs and economic factors based on historical data. Dassault Systèmes and the University of Texas at Dallas (UTD) contributed to the development of the Techno-Economic Model by providing macros to enable the generation of Bill of Material (BOM) data from a 3D blade design in either CATIA or NuMAD format, respectively. The TEM was built with the capability to directly import a Bill of Materials for economic analysis, and with the addition of the macros provided by Dassault and UTD, the TEM can directly import blade designs from both CATIA and NuMAD file formats. The modeling tools developed in Project 4.6 were used to investigate four wind blade manufacturing concepts in detail and select one to explore with laboratory-scale experimentation in Project 4.8. The four manufacturing concepts that were investigated were down-selected by the full project team from a larger list of concepts. The selections were made based on a number of criteria ranking viability and level of interest for each concept. The ‘One-Step Close’ manufacturing concept was ultimately selected for investigation in Project 4.8 and the demonstration was performed at the NREL CoMET facility. The TPI advanced manufacturing facility in Warren, RI contributed the production of several prototype components, the designs for which were developed by Janicki Industries. The demonstration project provided clear indication of the viability of the One-Step Close manufacturing concept for blade manufacturing and good validation of the Techno-Economic Model’s prediction of its economic impact.

17 WIND ENERGY↗
DOE OSTI2022

A particle resolved simulation approach for studying shock interactions with moving, colliding solid particles

This work applies a new combination of techniques for the fully resolved simulation of compressible, gas–particle multiphase flows. Here, the adaptive wavelet collocation method is used to dynamically, and efficiently, adapt the computational grid to localized flow features and the particles. A characteristic-based volume penalization method that imposes arbitrary Dirichlet, Neumann, or Robin-type immersed boundary conditions, is used to enforce the no-slip condition at particle surfaces. A hard-sphere collision model is applied to capture the particle–particle collisions. Proof of concept test cases are presented, showcasing the dynamic grid adaptation and fully resolved two-way coupling between the phases that is possible with this approach. Results for a shock-driven single cylinder under viscous and inviscid conditions are presented along with a demonstration of a shock interacting with a cloud of randomly distributed cylinders and spheres.

42 ENGINEERING↗
DOE OSTI2021

Exactness of OPF Relaxation on Three-phase Radial Networks with Delta Connections

Simulations have shown that while semi-definite relaxations of AC optimal power flow (AC-OPF) on three-phase radial networks with only wye connections tend to be exact, the presence of delta connections seem to render them inexact. This paper shows that such inexactness originates from the non-uniqueness of relaxation solutions and numerical errors amplified by the non-uniqueness. This finding motivates two algorithms to recover the exact solution of AC-OPF in unbalanced distribution networks featuring both wye and delta connections. In simulations using IEEE 13, 37 and 123-bus systems, the proposed algorithms provide exact optimal solutions up to numerical precision.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2016

Modeling seven years of event horizon telescope observations with radiatively inefficient accretion flow models

An initial three-station version of the Event Horizon Telescope, a millimeter-wavelength very-long baseline interferometer, has observed Sagittarius A* (Sgr A*) repeatedly from 2007 to 2013, resulting in the measurement of a variety of interferometric quantities. Of particular importance is that there is now a large set of closure phases measured over a number of independent observing epochs. We analyze these observations within the context of a realization of semi-analytic radiatively inefficient disk models, implicated by the low luminosity of Sgr A*. We find a broad consistency among the various observing epochs and between different interferometric data types, with the latter providing significant support for this class of model of Sgr A*. The new data significantly tighten existing constraints on the spin magnitude and its orientation within this model context, finding a spin magnitude of a=0.10{sub −0.10−0.10}{sup +0.30+0.56}, an inclination with respect to the line of sight of θ=60{sup ∘}{sub −8{sup ∘}−13{sup ∘+5{sup {sup ∘+10{sup {sup ∘}}}}}}, and a position angle of ξ=156{sup ∘}{sub −17{sup ∘}−27{sup ∘+10{sup {sup ∘+14{sup {sup ∘}}}}}} east of north. These are in good agreement with previous analyses. Notably, the previous 180° degeneracy in the position angle has now been conclusively broken by the inclusion of the closure-phase measurements. A reflection degeneracy in the inclination remains, permitting two localizations of the spin vector orientation, one of which is in agreement with the orbital angular momentum of the infrared gas cloud G2 and the clockwise disk of young stars. This may support a relationship between Sgr A*'s accretion flow and these larger-scale features.

79 ASTRONOMY AND ASTROPHYSICS↗