Search NASA⌕ Search

SEARCH · Search NASA

Results for “VAPOR PHASE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48

High carrier mobility of CoPc wires based field-effect transistors using bi-layer gate dielectric

Polyvinyl alcohol (PVA) and anodized Al{sub 2}O{sub 3} layers were used as bi-layer gate for the fabrication of cobalt phthalocyanine (CoPc) wire base field-effect transistors (OFETs). CoPc wires were grown on SiO{sub 2} surfaces by organic vapor phase deposition method. These devices exhibit a field-effect carrier mobility (μ{sub EF}) value of 1.11 cm{sup 2}/Vs. The high carrier mobility for CoPc molecules is attributed to the better capacitive coupling between the channel of CoPc wires and the gate through organic-inorganic dielectric layer. Our measurements also demonstrated the way to determine the thicknesses of the dielectric layers for a better process condition of OFETs.

36 MATERIALS SCIENCE↗

Nanowell-patterned TiO{sub 2} microcantilevers for calorimetric chemical sensing

A sensitive calorimetric sensor using a TiO{sub 2} microcantilever with nanowells patterned on one of its sides is described. This single material cantilever is sensitive to temperature change without relying on the metal deposition-based bimetallic effect. The thermomechanical sensitivity originates from the structure dependent variations in both the elastic modulus and thermal expansion coefficient due to the presence of ordered nanowells. These cantilever beams offer an alternate and efficient chemical sensing route for vapor phase analytes using photothermal spectroscopy. Selective and sensitive detection of organophosphorus compounds, as well as their photocatalytic decomposition under ultraviolet light exposure are demonstrated.

36 MATERIALS SCIENCE↗

Electron and hole drift mobility measurements on thin film CdTe solar cells

We report electron and hole drift mobilities in thin film polycrystalline CdTe solar cells based on photocarrier time-of-flight measurements. For a deposition process similar to that used for high-efficiency cells, the electron drift mobilities are in the range of 10{sup −1}–10{sup 0} cm{sup 2}/V s, and holes are in the range of 10{sup 0}–10{sup 1} cm{sup 2}/V s. The electron drift mobilities are about a thousand times smaller than those measured in single crystal CdTe with time-of-flight; the hole mobilities are about ten times smaller. Cells were examined before and after a vapor phase treatment with CdCl{sub 2}; treatment had little effect on the hole drift mobility, but decreased the electron mobility. We are able to exclude bandtail trapping and dispersion as a mechanism for the small drift mobilities in thin film CdTe, but the actual mechanism reducing the mobilities from the single crystal values is not known.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Localized surface plasmon resonance enhanced ultraviolet emission and F-P lasing from single ZnO microflower

In this work, monodispersed ZnO microflowers are fabricated by a vapor phase transport method, and Au nanoparticles (NPs) are directly decorated on the surface of the ZnO microflowers. The micro-photoluminescence of a single ZnO microflower demonstrates that the near band-edge emission is tremendously enhanced while the defect-related emission is completely suppressed after Au decoration. The average enhancement factor reaches up to 65 fold. The enhancement mechanism is assumed to be the electron transfer from excited Au NPs to the ZnO microflower induced by the localized surface plasmon resonance based on the time-resolved photoluminescence. The enhanced F-P lasing from a single ZnO sample is further realized.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dynamic competition between island growth and coalescence in metal-on-insulator deposition

The morphology of thin metal films and nanostructures synthesized from the vapor phase on insulating substrates is strongly influenced by the coalescence of islands. Here, we derive analytically the quantitative criterion for coalescence suppression by combining atomistic nucleation theory and a classical model of coalescence. Growth simulations show that using this criterion, a coalescence-free growth regime can be reached in which morphological evolution is solely determined by island nucleation, growth, and impingement. Experimental validation for the ability to control the rate of coalescence using this criterion and navigate between different growth regimes is provided by in situ monitoring of Ag deposition on SiO{sub 2}. Our findings pave the way for creating thin films and nanostructures that exhibit a wide range of morphologies and physical attributes in a knowledge-based manner.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

UV light sensing properties of Sm doped vertically aligned ZnO nanorod arrays

Samarium doped ZnO nanorods were grown on silicon substrate by using vapor phase transport method (VPT) with the growth temperature of 950°C. The synthesized nanorods were characterized by XRD, field emission scanning electron microscopy, Raman spectra, and photocurrent measurements. The XRD result revealed that Sm was successfully doped into lattice plane of hexagonal ZnO nanorods. The FESEM result confirms the pure ZnO has nanorod like morphology with an average diameter and length of 130nm and 10µm respectively. The above observation is supported by the Micro-Raman spectroscopy result. The photocurrent in the visible region has been significantly enhanced due to deposition of Sm on the surface of the ZnO nanorods. Sm acts as a visible sensitizer because of its lower band gap compared to ZnO.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Indium segregation during III–V quantum wire and quantum dot formation on patterned substrates

We report a model for metalorganic vapor-phase epitaxy on non-planar substrates, specifically V-grooves and pyramidal recesses, which we apply to the growth of InGaAs nanostructures. This model—based on a set of coupled reaction-diffusion equations, one for each facet in the system—accounts for the facet-dependence of all kinetic processes (e.g., precursor decomposition, adatom diffusion, and adatom lifetimes) and has been previously applied to account for the temperature-, concentration-, and temporal-dependence of AlGaAs nanostructures on GaAs (111)B surfaces with V-grooves and pyramidal recesses. In the present study, the growth of In{sub 0.12}Ga{sub 0.88}As quantum wires at the bottom of V-grooves is used to determine a set of optimized kinetic parameters. Based on these parameters, we have modeled the growth of In{sub 0.25}Ga{sub 0.75}As nanostructures formed in pyramidal site-controlled quantum-dot systems, successfully producing a qualitative explanation for the temperature-dependence of their optical properties, which have been reported in previous studies. Finally, we present scanning electron and cross-sectional atomic force microscopy images which show previously unreported facetting at the bottom of the pyramidal recesses that allow quantum dot formation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electrical compensation by Ga vacancies in Ga{sub 2}O{sub 3} thin films

The authors have applied positron annihilation spectroscopy to study the vacancy defects in undoped and Si-doped Ga{sub 2}O{sub 3} thin films. The results show that Ga vacancies are formed efficiently during metal-organic vapor phase epitaxy growth of Ga{sub 2}O{sub 3} thin films. Their concentrations are high enough to fully account for the electrical compensation of Si doping. This is in clear contrast to another n-type transparent semiconducting oxide In{sub 2}O{sub 3}, where recent results show that n-type conductivity is not limited by cation vacancies but by other intrinsic defects such as O{sub i}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Kinetic Monte Carlo simulations of GaN homoepitaxy on c- and m-plane surfaces

The surface orientation can have profound effects on the atomic-scale processes of crystal growth and is essential to such technologies as GaN-based light-emitting diodes and high-power electronics. We investigate the dependence of homoepitaxial growth mechanisms on the surface orientation of a hexagonal crystal using kinetic Monte Carlo simulations. To model GaN metal-organic vapor phase epitaxy, in which N species are supplied in excess, only Ga atoms on a hexagonal close-packed (HCP) lattice are considered. The results are thus potentially applicable to any HCP material. Growth behaviors on c-plane (0001) and m-plane (011¯0) surfaces are compared. We present a reciprocal space analysis of the surface morphology, which allows extraction of growth mode boundaries and direct comparison with surface X-ray diffraction experiments. For each orientation, we map the boundaries between 3-dimensional, layer-by-layer, and step flow growth modes as a function of temperature and growth rate. Two models for surface diffusion are used, which produce different effective Ehrlich-Schwoebel step-edge barriers and different adatom diffusion anisotropies on m-plane surfaces. Simulation results in agreement with observed GaN island morphologies and growth mode boundaries are obtained. These indicate that anisotropy of step edge energy, rather than adatom diffusion, is responsible for the elongated islands observed on m-plane surfaces. As a result, island nucleation spacing obeys a power-law dependence on growth rate, with exponents of –0.24 and –0.29 for the m- and c-plane, respectively.

36 MATERIALS SCIENCE↗

Role of threading dislocations in strain relaxation during GaInN growth monitored by real-time X-ray reflectivity

Ga 1–x In x N epilayers (x =0.09 or 0.14) grown on c-plane GaN layers with different densities of threading dislocations have been investigated by real-time x-ray reflectivity during metal-organic vapor phase epitaxial growth. We found that the density of pre-existing threading dislocations in GaN plays an important role in the strain relaxation of Ga 1–x In x N. Critical thicknesses were obtained and compared with theoretical predictions using the mechanical equilibrium model and the energy balance model. We report the critical thickness of GaInN varies inversely with dislocation density in the GaN sublayer. When the threading dislocation density in the sublayer was reduced by three orders of magnitude, the photoluminescence intensity of the Ga 0.86 In 0.14 N epilayer was improved by a factor of ten.

42 ENGINEERING↗

Evolution of AlGaN deep level defects as a function of alloying and compositional grading and resultant impact on electrical conductivity

AlGaN:Si epilayers with uniform Al compositions of 60%, 70%, 80%, and 90% were grown by metal-organic vapor phase epitaxy along with a compositionally graded, unintentionally doped (UID) AlGaN epilayer with the Al composition varying linearly between 80% and 100%. The resistivity of AlGaN:Si with a uniform composition increased significantly for the Al content of 80% and greater, whereas the graded UID-AlGaN film exhibited resistivity equivalent to 60% and 70% AlGaN:Si owing to polarization-induced doping. Deep level defect studies of both types of AlGaN epilayers were performed to determine why the electronic properties of uniform-composition AlGaN:Si degraded with increased Al content, while the electronic properties of graded UID-AlGaN did not. The deep level density of uniform-composition AlGaN:Si increased monotonically and significantly with the Al mole fraction. Conversely, graded-UID AlGaN had the lowest deep level density of all the epilayers despite containing the highest Al composition. These findings indicate that Si doping is an impetus for point defect incorporation in AlGaN that becomes stronger with the increasing Al content. However, the increase in deep level density with the Al content in uniform-composition AlGaN:Si was small compared to the increase in resistivity. This implies that the primary cause for increasing resistivity in AlGaN:Si with the increasing Al mole fraction is not compensation by deep levels but rather increasing activation energy for the Si dopant. As a result, the graded UID-AlGaN films maintained low resistivity because they do not rely on thermal ionization of Si dopants.

36 MATERIALS SCIENCE↗

Iron and intrinsic deep level states in Ga 2 O 3

In this study, using a combination of deep level transient spectroscopy, secondary ion mass spectrometry, proton irradiation, and hybrid functional calculations, we identify two similar deep levels that are associated with Fe impurities and intrinsic defects in bulk crystals and molecular beam epitaxy and hydride vapor phase epitaxi-grown epilayers of β-Ga 2 O 3 . First, our results indicate that Fe Ga , and not an intrinsic defect, acts as the deep acceptor responsible for the often dominating E2 level at ~0.78 eV below the conduction band minimum. Second, by provoking additional intrinsic defect generation via proton irradiation, we identified the emergence of a new level, labeled as E2*, having the ionization energy very close to that of E2, but exhibiting an order of magnitude larger capture cross section. Importantly, the properties of E2* are found to be consistent with its intrinsic origin. As such, contradictory opinions of a long standing literature debate on either extrinsic or intrinsic origin of the deep acceptor in question converge accounting for possible contributions from E2 and E2* in different experimental conditions.

36 MATERIALS SCIENCE↗

Thermal conductivity of GaN single crystals: Influence of impurities incorporated in different growth processes

The thermal conductivity of GaN crystals grown by different techniques is analyzed using the 3ω method in the temperature range of 30 K to 295 K. GaN wafers grown by the ammonothermal method show a significant variation in thermal conductivity at room temperature with values ranging between 164 W m -1 K -1 and 196 W m -1 K -1 . GaN crystals produced with the sodium flux and hydride vapor phase epitaxy methods show results of 211 W m -1 K -1 and 224 W m -1 K -1 , respectively, at room temperature. Analysis using secondary ion mass spectrometry indicates varying amounts of impurities between the respective crystals and explains the behavior of thermal conductivity trends in the samples. The observed difference between thermal conductivity curves suggests that scattering of phonons at point defects dominates the thermal conductivity of GaN within the investigated temperature range. Finally, deviations of model curves from thermal conductivity measurements and disparities between modelled characteristic lengths and actual sample thicknesses indicate that phonon resonances are active in GaN.

36 MATERIALS SCIENCE↗

Six-Junction Concentrator Solar Cells

We report on six-junction inverted metamorphic (6J IMM) solar cells developed for concentrator applications. Monolithic III-V structures are grown by metal organic vapor phase epitaxy with junction bandgaps of 2.06, 1.70, 1.40, 1.16, 0.94, and 0.70 eV. The top three junctions are lattice-matched to the GaAs substrate, but the bottom three junctions use three consecutive metamorphic compositionally graded buffers to transition the lattice constant to GaxIn1-xAs compositions with the previously listed bandgaps. Performance of 6J IMM devices at one-sun AM1.5 Direct conditions gives VOC = 5.301 V, JSC = 8.05 mA/cm2, fill factor=83.9%, and efficiency=35.8%. Promising operation at high concentration is achieved but the spectrum was not controlled to AM1.5D. Tunnel junctions do not limit until at least several hundred suns. High concentration performance appears to be limited by internal heterojunction barriers created by zinc diffusion that decreases the fill factor. The properties of each junction within the 6J IMM have been separately characterized through electroluminescence and luminescent coupling measurements.

14 SOLAR ENERGY↗

Effect of InAs quantum dots capped with GaAs on atomic-scale ordering in Ga 0.5 In 0.5 P

The CuPt ordering of the group III elements in Ga x In 1-x P ( x ≃ 0.5) has been observed to vary during growth by metalorganic vapor-phase epitaxy of InAs quantum dots capped with GaAs in a GaInP matrix. While ordering is not affected by the insertion of a GaAs layer, the growth of InAs quantum dots capped with GaAs results in ordered, partially ordered, or fully disordered GaInP. We show that the degree of ordering depends on the deposition time of the InAs quantum dots and on the thickness of the GaAs capping layer. Our results indicate that disordered GaInP occurs in the presence of excess indium at the growth surface, which results from the growth of strained InAs quantum dots. Ordering resumes when the excess indium is consumed. Cathodoluminescence, scanning transmission electron microscopy, and atomic force microscopy are used in this study to correlate the electronic properties and the microstructure of the thin films.

Atomic force microscopy↗

The chemical physics of sequential infiltration synthesis—A thermodynamic and kinetic perspective

Sequential infiltration synthesis (SIS) is an emerging materials growth method by which inorganic metal oxides are nucleated and grown within the free volume of polymers in association with chemical functional groups in the polymer. SIS enables the growth of novel polymer-inorganic hybrid materials, porous inorganic materials, and spatially templated nanoscale devices of relevance to a host of technological applications. Although SIS borrows from the precursors and equipment of atomic layer deposition (ALD), the chemistry and physics of SIS differ in important ways. These differences arise from the permeable three-dimensional distribution of functional groups in polymers in SIS, which contrast to the typically impermeable two-dimensional distribution of active sites on solid surfaces in ALD. In SIS, metal-organic vapor-phase precursors dissolve and diffuse into polymers and interact with these functional groups through reversible complex formation and/or irreversible chemical reactions. In this perspective, we describe the thermodynamics and kinetics of SIS and attempt to disentangle the tightly coupled physical and chemical processes that underlie this method. Here, we discuss the various experimental, computational, and theoretical efforts that provide insight into SIS mechanisms and identify approaches that may fill out current gaps in knowledge and expand the utilization of SIS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structural reversibility of Cu doped NU-1000 MOFs under hydrogenation conditions

The metal-organic framework (MOF), NU-1000, and its metalated counterparts have found proof-of-concept application in heterogeneous catalysis and hydrogen storage amongst others. A vapor-phase technique, akin to atomic layer deposition (ALD), is used to selectively deposit divalent Cu ions on oxo, hydroxo-bridged hexa-zirconium(IV) nodes capped with terminal –OH and -OH 2 ligands. Subsequent reaction with steam yields node-anchored, CuII-oxo,hydroxo clusters. We find that cluster installation via AIM (= ALD In MOFs) is accompanied by an expansion of MOF mesopore (channel) diameter . We investigated the behavior of the cluster-modified material, termed Cu-AIM-NU-1000, to heat treatment up to 325 °C, at atmospheric pressure with a low flow of H2 into the reaction cell. The response under these conditions revealed two important results: (1) Above 200 °C, the initially installed few-metal-ion clusters reduce to neutral Cu atoms. The neutral atoms migrate from the nodes and aggregate into Cu nanoparticles. While the size of particles formed in the MOF interior is constrained by the width of mesopores (ca. 3 nm), those formed on the exterior surface of the MOF can grow as large as ca. 8 nm. (2) Reduction and release of Cu atoms from the MOFs nodes is accompanied NU-1000 undergoes dynamic structural transformation as it reverts back to its original dimension following the release. These results show while the MOF framework itself remains intact at 325 °C in an H 2 atmosphere, the small, AIM-installed Cu II -oxo,hydroxo clusters are stable with respect to reduction and conversion to metallic nanoparticles only up to ~200 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗