Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - SWEEPBACK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Progress Towards the Design of a Natural Laminar Flow Wing for a Low-Boom Concept Using CDISC

The X-59 is being developed to evaluate the ability to reduce boom loudness to acceptable levels, with the ultimate goal of enabling supersonic flight overland. If successful, one of the future research challenges will be focused on reducing fuel burn. In this paper, Natural Laminar Flow (NLF) is proposed as a technology to decrease fuel burn for a low-boom configuration. This will require an evaluation of the compatibility of NLF wings for a low-boom configuration. As a first step towards this goal, the CATNLF method was employed using the CDISC design module to perform NLF design on an isolated wing from a low-boom configuration. The results show that the NLF wing features laminar flow over 46\% of the wing upper surface, providing a potential 8.3 drag count reduction relative to the design with no laminar flow. Off-design analyses were additionally performed to evaluate the performance of the NLF wing for changes in angle of attack and Mach number. The results showed that the NLF wing offers a performance benefit over the entire range of off-design conditions considered, with the majority of the laminar flow maintained for near cruise conditions. Future work will consider the full configuration, which will enable an assessment of the impact of the NLF wing design on sonic boom loudness. Additionally, attachment line transition will be addressed, which was predicted to result in a loss of laminar flow on the inboard 50\% span for this work. Finally, future research will focus on developing a method for effectively choosing the frequency-beta pairs used for the stability analysis to improve transition prediction and provide a more accurate estimate of the performance benefit.

Supersonic↗
NASA NTRSDate not supplied

Transition Analysis for the Pazy Wing

The Pazy wing, designed as a benchmark for highly flexible wings that experience large deformations, presents intriguing nonlinear phenomena due to its unique geometry with spanwise varying static deformation and low Reynolds number flow conditions. These phenomena include limit cycle oscillation related to laminar separation bubbles, boundary-layer transition, and dynamic stall. The primary focus of this study is to investigate transition behavior on the sagged Pazy wing under static loading by using the shear-stress-transport (SST)-based Langtry-Menter 𝜸 − 𝑹𝒆𝜽𝒕 transition model in the NASA OVERFLOW and FUN3D solvers. Based on the steady-state results obtained via different variants of the Langtry-Menter model, we investigate the likely transition behavior over a range of incidence angles. The predicted flowfield on the sagged Pazy wing is strongly three dimensional and the application of turbulence index as a viable indicator of the transition front in such flows is also explored. The study demonstrates the limitations of the Langtry-Menter model when applied to low Reynolds number flows. We introduce a spanwise periodic configuration to simulate a narrow-span section of the Pazy wing, specifically centered on one of the 14 nearly equidistant ribs spanning the wing. The computational results demonstrate that the spanwise periodic configuration provides a straightforward environment for studying transition characteristics as well as demonstrating systematic grid convergence and successful code-to-code comparisons. The research offers useful insights into the transition characteristics of flexible wings under various loading conditions, contributing to the field of aeroelastic simulations.

CFD Modeling↗
NASA NTRS1925

Results of recent experiments with slotted wings

This report gives the results of a recent series of experiments performed on a wing designed for a cantilever monoplane. Both wings were trapezial in their ground plan, with their tips rounded elliptically. These wing sections combine all known devices for increasing the lift, namely, the slot, the increased camber and angle of attack by means of an aileron running the whole length of the span. The last advance included in the wing section was an increase in wing area by means of an auxiliary wing adjusted by a sort of rectangular joint.

BOUNDARY LAYER THICKNESS↗
NASA NTRS1985

An Attached Flow Design of a Noninterferring Leading Edge Extension to a Thick Delta Wing

An analytical procedure for the determination of the shape of a Leading-Edge Extension (LEE) which satisfies design criteria, including especially noninterference at the wing design point, has been developed for thick delta wings. The LEE device best satisfying all criteria is designed to be mounted on a wing along a dividing stream surface associated with an attached flow design lift coefficient (C L,d ) of greater than zero. This device is intended to improve the aerodynamic performance of transonic aircraft at C L greater than C L,d system emanating from the LEE leading edge. In order to quantify this process a twisted and cambered thick delta wing was chosen for the initial application of this design procedure. Appropriate computer codes representing potential and vortex flows were employed to determine the dividing stream surface at C L,d and an optimized LEE planform shape at C L greater than C L,d , respectively. To aid in the LEE selection, the aerodynamic effectiveness of 36 planforms was investigated at C L greater than C L,d . This study showed that reducing the span of the candidate LEEs has the most detrimental effect on overall aerodynamic efficiency, regardless of the shape or area. Furthermore, for a fixed area, constant-chord LEE candidates were relatively more efficient than those with sweep less than the wing. At C L,d , the presence of the LEE planform best satisfying the design criteria was found to have no effect on the wing alone aerodynamic performance.

Leading edge extension↗
NASA NTRS1951

Stability and Control Characteristics of a Complete Airplane Model Having a Wing with Quarter-chord Line Swept Back 40 Degrees, Aspect Ratio 2.50, and Taper Ratio 0.42

An investigation has been made of a complete airplane model having a wing with the quarter-chord line swept back 40 degrees, aspect ratio 2.50, and taper ratio 0.42 to determine its low-speed stability and control characteristics. The longitudinal stability investigation included stabilizer and tail-off tests with different wing dihedral angles (Gamma = 0 degrees and Gamma = -10 degrees) over an angle-of-attack range for the cruising and landing configurations and tests. with a high horizontal-tail location (Gamma = -10 degrees) for the cruising configuration. Tests were made of the wing alone and to determine the effect of wing end plates in pitch. Lateral stability characteristics were determined for the airplane with different geometric wing dihedrals, with end plates, and with several dorsal modifications. Tests were made with ailerons and spoilers to determine control characteristics.

STABILITY, STATIC↗
NASA NTRS2014

Core and Wing Densities of Asymmetric Coronal Spectral Profiles: Implications for the Mass Supply of the Solar Corona

Recent solar spectroscopic observations have shown that coronal spectral lines can exhibit asymmetric profiles, with enhanced emissions at their blue wings. These asymmetries correspond to rapidly upflowing plasmas at speeds exceeding approximately equal to 50 km per sec. Here, we perform a study of the density of the rapidly upflowing material and compare it with that of the line core that corresponds to the bulk of the plasma. For this task, we use spectroscopic observations of several active regions taken by the Extreme Ultraviolet Imaging Spectrometer of the Hinode mission. The density sensitive ratio of the Fe(sub XIV) lines at 264.78 and 274.20 Angstroms is used to determine wing and core densities.We compute the ratio of the blue wing density to the core density and find that most values are of order unity. This is consistent with the predictions for coronal nanoflares if most of the observed coronal mass is supplied by chromospheric evaporation driven by the nanoflares. However, much larger blue wing-to-core density ratios are predicted if most of the coronal mass is supplied by heated material ejected with type II spicules. Our measurements do not rule out a spicule origin for the blue wing emission, but they argue against spicules being a primary source of the hot plasma in the corona. We note that only about 40% of the pixels where line blends could be safely ignored have blue wing asymmetries in both Fe(sub XIV) lines. Anticipated sub-arcsecond spatial resolution spectroscopic observations in future missions could shed more light on the origin of blue, red, and mixed asymmetries.

coronal spectral profiles↗
NASA NTRS2016

Analysis of Low-Speed Stall Aerodynamics of a Business Jets Wing Using STAR-CCM+

Reynolds-Averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) analysis was conducted: to study the low-speed stall aerodynamics of a GIII aircrafts swept wing modified with (1) a laminar-flow wing glove, or (2) a seamless flap. The stall aerodynamics of these two different wing configurations were analyzed and compared with the unmodified baseline wing for low-speed flight. The Star-CCM+ polyhedral unstructured CFD code was first validated for wing stall predictions using the wing-body geometry from the First AIAA CFD High-Lift Prediction Workshop.

fluid mechanics↗
NASA NTRS2018

Analysis of High-Speed Aerodynamics of a Swept Wing with Seamless Flaps

Computational fluid dynamics (CFD) analysis was conducted to evaluate the high-speed aerodynamics of a Gulfstream GIII airplane (Gulfstream Aerospace Corporation, Savannah, Georgia) swept wing modified with an experimental seamless, compliant flap called the Adaptive Compliant Trailing Edge (ACTE) flap for airworthiness. The high-speed aerodynamics of the modified ACTE wing were analyzed at a Mach number of 0.85 and an altitude of 40,000 ft. A polyhedral finite-volume unstructured Reynolds-averaged Navier-Stokes CFD code was used with a two-equation turbulence model. Wing aerodynamics sensitivities to lift coefficients, airplane engine operation, vortex generators (VGs), and ACTE flap deflections were examined. High-speed flow over the clean GIII wing without VGs was found to be complex with outboard shock and boundary-layer interactions causing flow separation over the upper wing surface upstream of the aileron, which could result in buffet and controllability problems at higher lift coefficient values. The VGs were found to improve the high-speed aerodynamics of the clean wing, as expected; however, ACTE flap deflections of as little as 1 to 2 deg were found to negate all of the aerodynamic benefits provided by the VGs at high speeds.

wings↗
NASA NTRSDate not supplied

X-57 Wing Structural Load Testing

The X-57 flight project will provide an opportunity to assess the benefits of distributed electric propulsion. The plan is to use a TECNAM P2006T twin-engine light aircraft (Aeronautiche TECNAM S.p.A., Capua, Italy) as the baseline aircraft, but design and fabricate a new wing to test the technology. The wing when fully integrated onto the X-57 TECNAM P2006T fuselage will incorporate two wingtip cruise electric motors and 12 high-lift electric motors along the wing span. The testing described in this paper confirmed the strength of the X-57 wing for flight and provided an opportunity to calibrate the wing flight strain gages for monitoring loads in flight. The X-57 wing was qualification tested in the National Aeronautics and Space Administration Armstrong Flight Research Center Flight Loads Laboratory. This paper documents the airworthiness approach, test setup, instrumentation, and preliminary results. The X-57 ground load testing lessons learned are also discussed.

Wing loading↗
NASA NTRS1956

Finite Span Wings in Compressible Flow

Equations are developed using the source distribution method for the velocity potential function and pressure on thin wings in steady and unsteady motion. Closed form solutions are given for harmonically oscillating wings of general plan form including the effect of the wing wake. Some useful examples are presented in an appendix for arrow, semielliptical, and hexagonal plan form wings.

WINGS, ELLIPTICAL↗
DOE OSTI2015

Effect of skin flexibility on aerodynamic performance of flexible skin flapping wings for micro air vehicles

As part of the ongoing research on micro air vehicles, the present work focuses on the effect of membrane flexibility on the aerodynamic performance of flexible latex flapping wings. Wings with membrane thicknesses 0.37, 0.28, and 0.13 mm are chosen, which are named as least flexible (A), flexible (B), and most flexible (C), respectively. The experiments are performed in an air chamber of size 1.5 m × 1.5 m × 1.5 m, facilitated with wind velocities up to 15 m/s. The time-averaged lift and drag as functions of flapping frequency, forward flight velocity, the angles of attack (AoA), and advance ratio (J). The novel electronic control system developed previously is used to monitor and measure the flapping frequency. It is found that the effect of flexibility on the aerodynamic performance mainly depends on the range of flight speed; at 7200 ≤ Re ≤ 18,000, the lift and drag increase with increase of flexibility, and at 18,000 ≤ Re ≤ 25,200, the lift decreases and drag increases with increase of flexibility. Hence latex compliant (Wing C) wings are advantageous in the low Re range, while the least flexible wing (Wing A) is preferable for higher range.

42 ENGINEERING↗
NASA NTRS1971

Autorotating wings - An experimental investigation.

The autorotation of a flat plate about its spanwise axis was experimentally studied. Most of the work was done with a wing mounted in a 5 x 7 ft low-speed wind tunnel. The measurements consisted of the unsteady lift, drag, angular acceleration and the wing rotation rate. The flow pattern was very different from that over a static wing. The maximum and average lift, drag and angular acceleration were measured for Reynolds numbers from 25,000 to 250,000. The effect of applying driving and retarding torques to the wing was studied. A variety of wing configurations were tested, together with freely falling wings. For Reynolds numbers above 4000 the average lift and drag coefficients were comparable to those observed in the fixed axis tests, and it appeared that the flow pattern was similar.

Smith, E. H.↗
NASA NTRS1973

V/STOL tilt rotor aircraft study. Volume 6: Preliminary design of a composite wing for tilt rotor research aircraft

The results of a study of the use of composite materials in the wing of a tilt rotor aircraft are presented. An all-metal tilt rotor aircraft was first defined to provide a basis for comparing composite with metal structure. A configuration study was then done in which the wing of the metal aircraft was replaced with composite wings of varying chord and thickness ratio. The results of this study defined the design and performance benefits obtainable with composite materials. Based on these results the aircraft was resized with a composite wing to extend the weight savings to other parts of the aircraft. A wing design was then selected for detailed structural analysis. A development plan including costs and schedules to develop this wing and incorporate it into a proposed flight research tilt rotor vehicle has been devised.

Soule, V. A.↗
NASA NTRS1973

An experimental investigation of three oblique-wing and body combinations at Mach numbers between 0.60 and 1.40

An experimental investigation was conducted in an 11- by 11-foot transonic wind tunnel to determine the aerodynamic characteristics of three oblique high aspect ratio wings in combination with a high fineness-ratio Sears-Haack body. The three wings had the same elliptical planform and base line curvature but had different airfoil sections. One wing had an airfoil section designed to have a lift coefficient of 1.0 at a Mach number of 0.7, another to have shock-free supersonic flow over the upper surface, and the other to have a lift coefficient of 1.3 at a Mach number of 0.6. Longitudinal and lateral-directional stability data were obtained at wing yaw angles of 0 deg, 45 deg, 50 deg, and 60 deg over a test Mach number range from 0.6 to 1.4 for angles of attack between minus 7 deg and 9 deg. Reynolds numbers for the study were 4 and 6 million per foot. Flow-visualization studies were made to examine the nature of the flow on the wing surfaces. Notable differences were found in the aerodynamic characteristics of the three wing-body combinations, particularly in the lateral-directional characteristics.

Graham, L. A.↗
NASA NTRS1974

Study of the single body yawed-wing aircraft concept

Areas relating to the development and improvement of the single-fuselage, yawed-wing transonic transport concept were investigated. These included: (1) developing an alternate configuration with a simplified engine installation;(2) determining a structural design speed placard that would allow the engine-airframe match for optimum airplane performance; and (3) conducting an aeroelastic stability and control analysis of the yawed-wing configuration with a flexible wing. A two-engine, single-fuselage, yawed-wing configuration was developed that achieved the Mach 1.2 design mission at 5560 km (3000 nmi) and payload of 18,140 kg (40,000 lb) with a gross weight of 217,700 kg (480,000 lb). This airplane was slightly heavier than the aft-integrated four-engine configuration that had been developed in a previous study. A modified structural design speed placard, which was determined, resulted in a 6% to 8% reduction in the gross weight of the yawed-wing configurations. The dynamic stability characteristics of the single-fuselage yawed-wing configuration were found to be very dependent on the magnitude of the pitch/roll coupling, the static longitudinal stability, and the dihedral effect.

Kulfan, R. M.↗
NASA NTRS1974

The effect of canard leading edge sweep and dihedral angle on the longitudinal and lateral aerodynamic characteristic of a close-coupled canard-wing configuration

A generalized wind-tunnel model, with canard and wing planforms typical of highly maneuverable aircraft, was tested in the Langley high-speed 7- by 10-foot tunnel at a Mach number of 0.30. The test was conducted in order to determine the effects of canard sweep and canard dihedral on canard-wing interference at high angles of attack. In general, the effect of canard sweep on lift is small up to an angle of attack of 16 deg. However, for angles of attack greater than 16 deg, an increase in the canard sweep results in an increase in lift developed by the canard when the canard is above or in the wing chord plane. This increased lift results in a lift increase for the total configuration for the canard above the wing chord plane. For the canard in the wing chord plane, the increased canard lift is partially lost by increased interference on the wing.

Gloss, B. B.↗
NASA NTRS1975

Computer programs for calculating the static longitudinal aerodynamic characteristics of wing-body-tail configurations

Four computer programs developed to calculate the longitudinal aerodynamic characteristics of wing-body and wing-body-tail combinations are presented. The R1307 program is based on a linear method and is limited to the small range of angles of attack for which the lift and moment characteristics of wings and bodies are linear with angle of attack. The CRSFLW program is based on a crossflow method of predicting the forces and moments on bodies alone or wing-body combinations over a large angle of attack range. The SUBSON program predicts the longitudinal aerodynamic characteristics of wing-body-tail combinations at subsonic speeds and at angles of attack for which symmetrical pairs of vortices are shed from the body nose and the leading and side edges of the lifting surfaces. Program SUPSON predicts the longitudinal aerodynamic characteristics of wing-body-tail combinations at supersonic speeds in the same angle-of-attack range. A description of the use of each program, instructions for preparation of input, a description of the output, program listings, and sample cases for each program are included.

Mendenhall, M. R.↗
NASA NTRS1974

Lifting-surface theory for a semi-infinite wing in oblique gust

An unsteady lifting-surface theory is developed for the calculation of the airload on a semi-infinite-span thin wing in a compressible flow due to interaction with an oblique gust. By using the solutions obtained for a two-dimensional wing, the problem is formulated so that the unknown is taken to be the difference between the airload on the semi-infinite wing and that on a two-dimensional wing under the same gust conditions. Since this airload difference is nonzero only near the wing tip, the control points need be distributed in the tip region only; this significantly simplifies the numerical procedure. Results are presented for a wing with rectangular tip. The implication for noise and unsteady loads due to blade-vortex interaction for helicopter rotors is discussed.

Chu, S.↗